Original record summaries, dates and identifiers for this model-year. Records 101–200 of 396, ordered newest first. Dated records on this page: Aug 11, 2017–Apr 7, 2021.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 7, 2021Service Bulletin/Repair Instructions
9003453
NHTSA communication ID: 10221096
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacyed Content.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.
Source components: PARKING BRAKE · POWER TRAIN · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacyed Content.
Source components: BACK OVER PREVENTION · FUEL SYSTEM, GASOLINE · POWER TRAIN · SUSPENSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Split/Crack of Metal Body Side Door Check Strap This bulletin involves retrofitting the door check strap mounting on the body side. The customer may notice a metal split or crack on the body side on either the driver or passenger side of the door check strap area
NHTSA source summary · Original PDF not reviewed by Recallfolio
Split/Crack of Metal Body Side Door Check Strap This bulletin involves retrofitting the door check strap mounting on the body side. The customer may notice a metal split or crack on the body side on either the driver or passenger side of the door check strap area
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission,Trans Oil Pump,Torque Converter, Flexplate, Rear Seal, Engine NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flex plate found broken on vehicles > 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on trans bell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblong holes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Split/Crack of Metal Body Side Door Check Strap This bulletin involves retrofitting the door check strap mounting on the body side. The customer may notice a metal split or crack on the body side on either the driver or passenger side of the door check strap areaFig. 1.Check Strap Area Cracking
Source components: AIR BAGS · STRUCTURE · VEHICLE SPEED CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Split/Crack of Metal Body Side Door Check Strap This bulletin involves retrofitting the door check strap mounting on the body side. The customer may notice a metal split or crack on the body side on either the driver or passenger side of the door check strap areaFig. 1.Check Strap Area Cracking
NHTSA source summary · Original PDF not reviewed by Recallfolio
Split/Crack of Metal Body Side Door Check Strap This bulletin involves retrofitting the door check strap mounting on the body side. The customer may notice a metal split or crack on the body side on either the driver or passenger side of the door check strap areaFig. 1.Check Strap Area Cracking
NHTSA source summary · Original PDF not reviewed by Recallfolio
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CABLE, Gearshift Control If you are replacing a transmission shift cable on a VF ProMaster vehicle built with a 3.6L engine, for binding/kinked/seized or broken cable please take a picture of the shifter end of the cable, from the bottom of the cable mounting clip to the shifter end of the cable, also take a picture of the 4 digit code printed in white on the outer covering of the cable. Send pictures with VIN to Bob Henderson at bob.henderson@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Left Transmission Mount Bracket Fasteners This bulletin is to emphasize the importance of replacing and torquing the one time use bolts that fasten the left transmission mount bracket to the transmission.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Heating, Ventilation and Air Conditioning (HVAC) Module Updates This bulletin involves reprogramming the HVAC control module with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination with one or more of the following Diagnostic Trouble Codes (DTCs) or the symptom/conditions listed below:U1710-86 - Implausible Data Received From HVAC. U1710-87 - ACM (Automatic Climate Module) On B CAN - Missing Message. The HVAC control for the air conditioning/heating outlet control, fan speed or other controls maybe inoperative after a Body Control Module (BCM) had been replaced. The rear defrost/heated mirror LED indicator on the HVAC controller does not illuminate when the button is depressed(2014 MY only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison (248-292-9510) ron.dallison@fcagroup.com Joe Lovell (734) 309-6467 - joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair. All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Job aid - If you have a suspected TC shudder/vibration, check the Interactive Network for Service Bulletins for the vehicle you are working on. A test-drive snap shot may help you isolate the source of the issue.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Body Control Module (BCM) Diagnostic and System Improvements This bulletin involves reprogramming the BCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:U0019-01-CAN B BUS - General Electrical Failure(2015 MY Only). In addition, the following software enhancements are available:Update to allow the programming of one additional key without reprogramming all other keys. Fog light telltale stays illuminated when the high-beams are turned on(2015 MY Only). Allow for the vehicle to be locked with the key in the ignition(2015 MY Only). Additional updates for upfitters to correct the following conditions when using LED bulbs for the turn signals and enabling the ?Bulb Out Diagnostics?:External lamp failure icon being illuminated(2015 MY Only). Turn signal indicators flash at double the normal speed(2015 MY Only). Bulb out message displayed in the Electronic Vehicle Information Center (EVIC)(2015 MY Only).
Source components: AIR BAGS · ELECTRICAL SYSTEM · EXTERIOR LIGHTING · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Notification T12 VECI Label The Vehicle Emission Control Information (VECI) label on about 120,000 of the above vehicles may be missing emission control information. The VECI label is often used during in-use Inspection and Maintenance (I/M) testing to verify proper emissions related components. Incorrect VECI label information could result in denial of vehicle registration for the vehicle in the state of California. A new VECI label must be installed.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tire Pressure Monitor Jumper Harness This bulletin involves installing a Tire Pressure Monitor (TPM) jumper harness. The customer may describe a TPM warning light turn on due missing information or localization failure.Replacement of the TPM jumper harnessFig. 1will be necessary. Refer toStep 1.Tire Pressure Monitor Jumper Harness
Source components: ELECTRICAL SYSTEM · TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Outside Mirror Turn Signal is Inoperative This bulletin involves replacing both outside mirror turn signal housings and bulbs. Customer may experience "external lighting failure" indicator light along with accelerated blinking during turn signal operation. The inner turn signal amber lens may be distorted from excessive heat. Upon further investigation the technicianmay find one or more of the following Diagnostic Trouble Codes (DTCs):B1008-18 - Right Turn Lamp - Under Current. B1007-18 - Left Turn Lamp - Under Current.
Source components: AIR BAGS · EXTERIOR LIGHTING · VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR.