Original record summaries, dates and identifiers for this model-year. Records 101–200 of 585, ordered newest first. Dated records on this page: Aug 1, 2023–Feb 11, 2025.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Feb 11, 2025Service Bulletin/Repair Instructions
03-001-25 REV. A
NHTSA communication ID: 11014369
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Clicking Noise While In 4WD Customers may experience the following: ● Ratcheting, click, or clicking noise in 4WD while turning. This bulletin involves replacing the front driveshaft."
Source components: POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Clicking Noise While In 4WD ustomers may experience the following: ● Ratcheting, click, or clicking noise in 4WD while turning. his bulletin involves replacing the front driveshaft"
NHTSA source summary · Original PDF not reviewed by Recallfolio
TRANSFER CASE BW 44-46 If fluid leak is present between the transfer case and the rear driveshaft on a 4WD vehicle the Output Shaft Seal should be considered in lieu of entire transfer case or driveshaft replacement. In the case of major damage to components, contact StarCenter and/or proceed with replacements as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SWITCH Headlamp Before replacing the Headlamp Switch for faulty dimmer operation. Please follow the next steps to corroborate if the Headlamp Switch is malfunctioning: 1.- Please disconnect and reconnect the headlamp Switch. And verify if the issue is corrected. 2.- Review the internal resistance of the switch: a.- For the Right Dimmer (IP) between Pins 6 & 3. The value should be around 5.74 KOhms, when in the lowest position to 311 ohms in the top position (Parade Detent). b.- For the left Dimmer (Ambient Light) between pins 8 & 3. The value should be around 14.52 KOhms, when in the lowest position to 182 ohms in the top position. If a problem is found in the resistor values. Please replace the Switch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Brake Warning Lamp Illumination Over Rumble Strips Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● C003A-2F - Right Rear Wheel Speed Sensor - Signal Erratic. ● C0037-2F - Left Rear Wheel Speed Sensor - Signal Erratic. Customers may also comment on the following: ● Automatic Brake System (ABS) lamp and Electronic Stability Control (ESC) lamp turn on when driving over rumble strips. This bulletin involves replacing one or both rear wheel speed sensors. "
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Flash: Diesel Exhaust Fluid (DEF) Dosing Control Unit (DCU) Update Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P21C4-00 - Reductant Line Heater Relay Control Circuit High. ● U11C1-00 - Reductant Control Module Received Implausible Data From ECM/PCM. These DTCs will occur after installation of service DCU 68458603AB. This bulletin involves reprogramming the DCU with the latest available software."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Flash: Anti-Lock Brake System (ABS) Module Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● **C2200-47 - Anti-Lock Brake Module Internal - Watchdog / Safety Auc Failure.** ● C006A-49 - Multi-Axis Acceleration Sensor - Internal Electronic Failure. Customers may also comment on one or more of the following: ● **Anti-lock Brake System (ABS) indicator light illuminated in the Instrument Panel Cluster (IPC). ● Electronic Stability Control (ESC) indicator light illuminated in the IPC. ● The Red Brake Warning indicator light illuminated in the IPC.** This bulletin involves reprogramming the ABS with the latest software available."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transfer case BW44-47 If fluid leak is present between the transfer case and the rear driveshaft on a 4WD vehicle the Output Shaft Seal - sub component parts should be considered in lieu of entire transfer case or driveshaft replacement. In the case of major damage to components, contact StarCenter and/or proceed with replacements as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Diesel Exhaust Fluid (DEF) Fluid Freezing Warranty Extension XR1 Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P203E-00 - Reductant Level Sensor 1 Circuit Intermittent-Erratic. Customers may also experience one or more of the following: ● Repeated freeze/thaw cycles of the urea tank to cause solid DEF crystals to form and settle on the focus tube, blocking the level sensor signal. ● Rapid temperature swings from below freezing to above freezing causing an incomplete thaw of the DEF tank. When the vehicle is powered on, the diagnostic is enabled due to thawed DEF at the tank bottom surface, but the fluid in the center is still partially frozen. ● Not following the proper DEF fill procedure and overfilling the tank. This bulletin involves replacing the urea delivery module and possibly updating the Dosing Control Unit (DCU) software"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Diesel Exhaust Fluid (DEF) Fluid Freezing Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P203E-00 - Reductant Level Sensor 1 Circuit Intermittent-Erratic. Customers may also experience one or more of the following: ● Repeated freeze/thaw cycles of the urea tank to cause solid DEF crystals to form and settle on the focus tube, blocking the level sensor signal. ● Rapid temperature swings from below freezing to above freezing causing an incomplete thaw of the DEF tank. When the vehicle is powered on, the diagnostic is enabled due to thawed DEF at the tank bottom surface, but the fluid in the center is still partially frozen. ● Not following the proper DEF fill procedure and overfilling the tank This bulletin involves replacing the urea delivery module and grade vent valve and updating the Dosing Control Unit (DCU) software This bulletin involves replacing the urea delivery module and possibly updating the Dosing Control Unit (DCU) software"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Replace K1 Clutch / Input Shaft Assembly Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0731-00 - Gear 1 Shift Incorrect Ratio (This DTC will set during a key cycle and shifting into Drive). Customers may also comment on the following: ● The transmission will not shift into or out of 1st - 4th gears. 5th and reverse gears are still available. **This bulletin involves replacing the K1 clutch and possibly the K1 input shaft drum sub-assembly. These repairs are to be performed only if the vehicle is inoperable due to K1 clutch failure. ** "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Diesel Exhaust Fluid (DEF) Fluid Freezing Warranty Extension XR1 Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P203E-00 - Reductant Level Sensor 1 Circuit Intermittent-Erratic. Customers may also experience one or more of the following: ● Repeated freeze/thaw cycles of the urea tank to cause solid DEF crystals to form and settle on the focus tube, blocking the level sensor signal. ● Rapid temperature swings from below freezing to above freezing causing an incomplete thaw of the DEF tank. When the vehicle is powered on, the diagnostic is enabled due to thawed DEF at the tank bottom surface, but the fluid in the center is still partially frozen. ● Not following the proper DEF fill procedure and overfilling the tank. This bulletin involves replacing the urea delivery module and possibly updating the Dosing Control Unit (DCU) software."
NHTSA source summary · Original PDF not reviewed by Recallfolio
WARRANTY BULLETIN D-24-15 announces the addition of the Rear Axle Assembly replacement for 2019 - 2024 RAM 3500 Cab Chassis (DD), RAM 4500/ 5500 Cab Chassis (DP), RAM 3500 Pickup (D2), RAM 2500 Pickup (DJ), RAM 1500 Pickup (DS) and RAM 1500 Pickup (DT) vehicles to the Powertrain Pre-Authorization program for all dealers (Base, Plus & Premium) to ensure proper repair of Rear Axle Assembly failures and to assist in quality improvements. REV.A
NHTSA source summary · Original PDF not reviewed by Recallfolio
"WARRANTY BULLETIN D-24-15 Addition of Rear Axle / Differential Assembly for 2019 - 2024 RAM 3500 Cab Chassis (DD) to the Powertrain Service Center (PTSC) Pre-Authorization Program ALL DEALERS"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"FCA CARIBBEAN WARRANTY BULLETIN ID-24-16 Addition of Rear Axle / Differential Assembly for 2019 - 2024 RAM 3500 Cab Chassis (DD) to the Powertrain Service Center (PTSC) Pre-Authorization Program"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."
NHTSA source summary · Original PDF not reviewed by Recallfolio
TRANSFER CASE BW 44-46 If fluid leak is present between the transfer case and the rear driveshaft on a 4WD vehicle the Output Shaft Seal - service part numbers 68161329AA OR 68449218AA (max tow application) - should be considered in lieu of entire transfer case or driveshaft replacement. In the case of major damage to components, contact StarCenter and/or proceed with replacements as necessary
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Rear Axle Vibration Shudder Or Chatter Customers may experience the following: ● A chatter, shudder, or vibration from the rear axle during turns. NOTE: This may happen more as the vehicle ages, especially if the vehicle is used extensively for towing or hauling heavy loads. The cause of the concern may be due to degradation of the rear axle fluid. It is very important to follow the routine maintenance schedules on these vehicles when it comes to changing the rear axle fluid if the vehicle is used primarily for towing or hauling heavy loads. If you experience a vehicle with the above condition, please perform the proper maintenance procedures for the rear axle and replace the fluid first before replacing any hardware components. NOTE: This service bulletin is only applicable to vehicles that have no history of an axle fluid replacement. If the vehicle usage includes police, taxi, fleet, off-road or frequent trailer towing, regular axle fluid changes are required every 3 years or 30,000 miles (whichever comes first) per the Maintenance Schedule in the vehicle Owner's Manual. This bulletin involves changing the rear axle lube to possibly address a chatter, shudder or vibration."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Diesel Exhaust Fluid (DEF) Fluid Freezing **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC):** ● P203E-00 - Reductant Level Sensor 1 Circuit Intermittent-Erratic. Customers may also experience one or more of the following: ● Repeated freeze/thaw cycles of the urea tank to cause solid DEF crystals to form and settle on the focus tube, blocking the level sensor signal. ● Rapid temperature swings from below freezing to above freezing causing an incomplete thaw of the DEF tank. When the vehicle is powered on, the diagnostic is enabled due to thawed DEF at the tank bottom surface, but the fluid in the center is still partially frozen. ● Not following the proper DEF fill procedure and overfilling the tank.** This bulletin involves replacing the urea delivery module and grade vent valve and updating the Dosing Control Unit (DCU) software."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"GENERATOR Engine Prior to alternator/generator removal: 1. Inspect & check all electrical connections to the alternator a. 2-way connector containing field control circuit & alternator sense voltage circuit. b. Unplug & plug-in the 2-way connector for field & sense circuit. Verify the connection is tight & check for any bent pins in alternator connector or damage to female terminals in connector. c. Check Alternator B+ Stud connection to be sure nut is securing positive cable terminal properly (i.e. nut is clamping terminal & connection is tight). d. Check fuse between the alternator B+ stud & PDC terminal to make sure it is not blown. e. Be sure to follow service manual sections on ALTERNATOR CONTROL CIRCUIT DIAGNOSTIC & ALTERNATOR SENSE CIRCUIT DIAGNOSTIC looking for any opens & shorts (to ground or battery voltage). 2. Check/verify all grounds in the charging system circuit a. Check tightness of mounting bolts securing alternator to engine block. Alternator is a case ground component. b. Check main ground from engine to chassis; connection must be tight. c. Check battery ground cable connections are tight. d. Potentially, loosen alternator mounting bolts, without removing alternator, and re-tighten to torque specifications in service manual. e. After all steps above are complete, re-start engine & check charging system operation. 3. Verify that the Smart Charging System is not the reason for alternator low voltage & current output (Amps). a. Alternator charging can be suspended during engine idle operation because of the Smart Charge strategy. b. Refer to service manual section ""System Operation - Smart Charging System"". c. Refer to Star Case S2008000031 Rev A for low charging voltage & Smart Charge Mode Voltage Range diagram & mode descriptions. d. The alternator has no internal regulator; thus, has no smart circuitry. All alternator control signals come from ECM. 4. If alternator is faulty, remove alternator & mounting bolts. Return alternator with bolts for analysis at QEC."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Update from LR34.51 to LR35.41 Software Version Customer may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from LR34.51 to LR35.41. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Update from QR39.82F to QR40.12 Software Version Customer may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.82F to QR40.12. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.
NHTSA source summary · Original PDF not reviewed by Recallfolio
C003A-2F Right Rear Wheel Speed Sensor, C0037-2F Left Rear Wheel Speed Sensor Diagnostic Trouble Codes (DTCs) Set While Driving With Payload Or Trailer Towing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Update from QR39.5 to QR40.11 Software Version Customer may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.5 to QR40.11. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Updating to QR40.12 Software Version Customers may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.2 to QR40.11. NOTE: National launch for this FOTA update is expected to begin February 19, 2023.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Update to LR34.31 to LR35.41 Software Version Customers may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from LR34.31 to LR35.41. NOTE: The National launch for this FOTA update campaign is expected to begin December 04, 2023.
Source components: ELECTRICAL SYSTEM:SOFTWARE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Update to Q339.3 to QR39.62 Software Version Customers may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from Q339.3 to QR39.62. NOTE: The National launch for this FOTA update campaign is expected to begin December 04, 2023.
Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC. · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Updating From QR39.6 to QR40.12 Software Version Customers may experience one or more of the following symptoms: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.6 to QR40.12. NOTE: National launch for this FOTA update is expected to begin November 06, 2023.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC. · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rain Sensor Before replacing the rain sensor during a front windshield replacement inspect the part for part numbers. If you have part numbers; 68507366, 68483780, 68384226 or 68384225, these parts do not utilize a replaceable gel pad, only replace the sensor for a missing or damaged gel pad. For part numbers 68298334, 68298468, 68607452 or 68194700 the gel pad should be replaced during all windshield replacements and can be ordered through MOPAR, complete sensor replacement is not necessary. Contact: FCA Redacted Content for further questions If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rain Sensor Before replacing the rain sensor during a front windshield replacement inspect the part for part numbers. If you have part numbers; 68507366, 68483780, 68384226 or 68384225, these parts do not utilize a replaceable gel pad, only replace the sensor for a missing or damaged gel pad. For part numbers 68298334, 68298468, 68607452 or 68194700 the gel pad should be replaced during all windshield replacements and can be ordered through MOPAR, complete sensor replacement is not necessary. Contact: FCA Redacted Content for further questions If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
C003A-2F Right Rear Wheel Speed Sensor, C0037-2F Left Rear Wheel Speed Sensor Diagnostic Trouble Codes (DTCs) Set While Driving With Payload Or Trailer Towing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
K1 Clutch Snap Ring Repair Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) has been set: ? P0731-00 - Gear 1 Shift Incorrect Ratio (This DTC will set during a key cycle and shifting into Drive). Customers may also comment on the following: ? The transmission will not shift into/or out of 1st - 4th gears. 5th and reverse gears are still available. This bulletin involves replacing the K1 clutch drum snap ring and possibly the K1 input shaft drum subassembly.