Original record summaries, dates and identifiers for this model-year. Records 101–200 of 393, ordered newest first. Dated records on this page: May 29, 2019–Apr 17, 2021.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 17, 2021Service Bulletin/Repair Instructions
S1608000226
NHTSA communication ID: 10221153
NHTSA source summary · Original PDF not reviewed by Recallfolio
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PLATE - CLUTCH PRESSURE For 68RFE trans use selective fit pressure plates between the overdrive and reverse clutch packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$
NHTSA source summary · Original PDF not reviewed by Recallfolio
PLATE - CLUTCH PRESSURE For 68RFE trans use selective fit pressure plates between the overdrive and reverse clutch packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer may complain of a MIL lamp on. Upon further investigation there could be a fault code in the PCM for P1524 ? Oil Pressure Out of Range ? Camshaft Advance/Retard Disabled.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer may complain of a MIL lamp on. Upon further investigation there could be a fault code in the PCM for P1524 ? Oil Pressure Out of Range ? Camshaft Advance/Retard Disabled.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
Source components: ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Drivetrain Control Module (DTCM) Update This bulletin involves reprogramming the DTCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set::If the customer has any concerns with the transfer case or if the tech performs any repairs on the transfer case, the software must be updated.C140E - Transfer Case Motor Blocked. If DTC C140E is present, follow normal diagnostic procedures before updating the DTCM.In addition the customer may describe the following:The ?Service 4WD? message/fault is displayed in the Instrument Panel Cluster (IPC). Transfer case shift fork tabs broken during range shift. Noisy (clunking/ratcheting) transfer case range shifts. Failure to complete transfer case range shifts. The following software enhancement is available:This update will help reduce premature transfer case failure.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Drivetrain Control Module (DTCM) Update This bulletin involves reprogramming the DTCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set::If the customer has any concerns with the transfer case or if the tech performs any repairs on the transfer case, the software must be updated.C140E - Transfer Case Motor Blocked. If DTC C140E is present, follow normal diagnostic procedures before updating the DTCM.In addition the customer may describe the following:The ?Service 4WD? message/fault is displayed in the Instrument Panel Cluster (IPC). Transfer case shift fork tabs broken during range shift. Noisy (clunking/ratcheting) transfer case range shifts. Failure to complete transfer case range shifts. The following software enhancement is available:This update will help reduce premature transfer case failure.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Power Distribution Center If the PDC is being replaced due to a failed internal fuel pump relay, the relay can now be serviced as a separate component. Please use relay replacement KIT part number: 68510768A$.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Intelligent Power Distribution Center If the PDC requires replacement due to a failed internal fuel pump relay, the relay can now be serviced as a separate component. Please use relay replacement KIT part number: 68510768A$.
NHTSA source summary · Original PDF not reviewed by Recallfolio
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
6.7L New Oil Usage Information This bulletin provides information regarding the correct oil grade to use on the 6.7L Cummins used in the 2019 and newer HD Trucks. The following information is intended to eliminate confusion.
NHTSA source summary · Original PDF not reviewed by Recallfolio
6.7L New Oil Usage Information This bulletin provides information regarding the correct oil grade to use on the 6.7L Cummins used in the 2019 and newer HD Trucks. The following information is intended to eliminate confusion.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
6.7L New Oil Usage Information This bulletin provides information regarding the correct oil grade to use on the 6.7L Cummins used in the 2019 and newer HD Trucks. The following information is intended to eliminate confusion.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Anti-lock Brake System (ABS) Enhancements This bulletin involves reprogramming the ABS module with the latest software available. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set:C006A-49 - Multi-Axis Acceleration Sensor - Internal Electronic Failure.
Source components: SERVICE BRAKES, AIR:ANTILOCK:CONTROL UNIT/MODULE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GASKET, Timing Case Cover, Rear Gear Housing For 2017-2020 model years only. If you are replacing the timing housing gasket due to an oil leak, please take detailed pictures of the leak, and submit them to the Star Center. Once submitted, continue with the repair. During the repair, check the breakaway torque of the gear housing retaining bolts. If any are found to be loose, note the location of the loose bolt(s) in the Star case.
Source components: ENGINE AND ENGINE COOLING · STEERING:GEAR BOX (OTHER THAN RACK AND PINION).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Axle Vibration, Shudder Or Chatter This bulletin involves changing the rear axle lube to possibly address a chatter, shudder or vibration. The customer may describe the following: A chatter, shudder, or vibration from the rear axle during turns. This may happen more as the vehicle ages, especially if the vehicle is used extensively for towing or hauling heavy loads. The cause of the concern may be due to degradation of the rear axle fluid. It is very important to follow the routine maintenance schedules on these vehicles when it comes to changing the rear axlefluid if the vehicle is used primarily for towing or hauling heavy loads. If you experience a vehicle with the above condition, please perform the proper maintenance procedures for the rear axle and replace the fluid first before replacing any hardware components.This service bulletin is only applicable to vehicles that have no history of an axle fluid replacement. If the vehicle usage includes police, taxi, fleet, off-road or frequent trailer towing, regular axle fluid changes are required every2 years or 20,000 miles (whichever comes first) per the Maintenance Schedule in the vehicle Owner's Manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · SUSPENSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MODULE, Anti-Lock Brake System If ordering ECU PN 68347098AB or later to repair a C0020-01 ABS PUMP MOTOR CONTROL - GENERAL ELECTRICAL FAILURE, The HCU Hydraulic Control Unit can be replaced alone for this DTC. For any other DTC's follow published diagnostics.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CASE ASSEMBLY, Differential For concern of shudder/chatter/vibration from the rear axle that is more prominent during turns and customer has the following: 1) Limited Slip Differential 2) No record of rear axle oil being serviced in the last 20,000 miles 3) No apparent damage to the axle/differential case or differential case internal gears Service the rear axle oil with new and test drive to see if condition is still present. If still present follow standard diagnostic procedures and contact FCA Redacted Content for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the followingDTC has been set:U1111-00 - Lost Odometer Message(DD, DF, and DP with Diesel Engine Only). In addition, the customer may notice one or more of the following conditions: The customer may notice a harsh 2-3 and/or 3-4 shift(2017 MY D2 with ETK 6.7L Diesel and DF2 Transmission Only). 1-2 hard shift. 3-4 flare issue fix. Trans quick learn fix(Gas Engine Only). Transmission oil temperature light illumination during high engine and tow loads. Less than desired towing performance while using cruise control. Harsh engagement while shifting from neutral to drive, neutral to reverse,or park to reverse with vehicle still in motion (rolling garage shift). Engine flare during 2-1 tip in downshift. Less than desired shift quality during 6-5 and 5-4 coasting downshifts. Delayed downshifts in Tow/Haul mode while driving down grades. Less than desired transmission shift performance when transitioning froma low traction to high traction surfaces i.e. ice covered road to clear pavement. Less than desired shift points during light pedal and Wide Open Throttle(WOT) operation or while in Tow/Haul and engine brake modes. 1-2 upshift shudder correction(Diesel engine and DF2 Transmission Only). A harsh 1-2 upshift(DF2 Transmission Only). Excessive gear shifting(DF2 Transmission Only). Harsh 2-1 downshift(DF2 Transmission Only). Delayed engagement when shifting from neutral to drive, neutral to reverse,or park to reverse (garage shifts)(DF2 Transmission Only). Audible squawk noise on 4-3 downshift(DF2 Transmission Only). Poor vehicle acceleration in first gear with vehicle fully loaded(DF2 Transmission Only). MIL illumination with no defect found forDTC P253D - PTO Sense Circuit High(DF2 Transmission Only).
Source components: AIR BAGS · BACK OVER PREVENTION · ELECTRICAL SYSTEM · EXTERIOR LIGHTING · FUEL SYSTEM, DIESEL · FUEL SYSTEM, GASOLINE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the followingDTC has been set:U1111-00 - Lost Odometer Message(DD, DF, and DP with Diesel Engine Only). In addition, the customer may notice one or more of the following conditions: The customer may notice a harsh 2-3 and/or 3-4 shift(2017 MY D2 with ETK 6.7L Diesel and DF2 Transmission Only). 1-2 hard shift. 3-4 flare issue fix. Trans quick learn fix(Gas Engine Only). Transmission oil temperature light illumination during high engine and tow loads. Less than desired towing performance while using cruise control. Harsh engagement while shifting from neutral to drive, neutral to reverse,or park to reverse with vehicle still in motion (rolling garage shift). Engine flare during 2-1 tip in downshift. Less than desired shift quality during 6-5 and 5-4 coasting downshifts. Delayed downshifts in Tow/Haul mode while driving down grades. Less than desired transmission shift performance when transitioning froma low traction to high traction surfaces i.e. ice covered road to clear pavement. Less than desired shift points during light pedal and Wide Open Throttle(WOT) operation or while in Tow/Haul and engine brake modes. 1-2 upshift shudder correction(Diesel engine and DF2 Transmission Only). A harsh 1-2 upshift(DF2 Transmission Only). Excessive gear shifting(DF2 Transmission Only). Harsh 2-1 downshift(DF2 Transmission Only). Delayed engagement when shifting from neutral to drive, neutral to reverse,or park to reverse (garage shifts)(DF2 Transmission Only). Audible squawk noise on 4-3 downshift(DF2 Transmission Only). Poor vehicle acceleration in first gear with vehicle fully loaded(DF2 Transmission Only). MIL illumination with no defect found forDTC P253D - PTO Sense Circuit High(DF2 Transmission Only).
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIO, MULTI Media For RA3 and RA4 8.4? radio concern of reoccurring update request pop-up on each key cycle after a radio FOTA (Firmware Update Over the Air) has been completed, please DO NOT replace the radio. To recover the radio, 12v power needs to be disconnect from the radio to clear radio memory either by removal of the radio fuse or preforming a battery disconnect. Note: Fuse removal is the preferred method. The radio needs to be disconnected from power long enough to clear memory and discharge the Capacitance within the radio. Please refer to the latest in diagnostics for further information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash Over The Air (FOTA) Software Update RA3 and RA4 Radio This bulletin provides information regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.