Original record summaries, dates and identifiers for this model-year. Records 301–400 of 489, ordered newest first. Dated records on this page: Mar 30, 2016–Jul 20, 2016.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jul 20, 2016Service Bulletin/Repair Instructions
05086755A$
NHTSA communication ID: 10121687
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Crank Shaft Oil Seal and retainer plate For Cummins equipped vehicles only;~ If replacing Rear Main Seal for oil leak, replace seal and retainer as a set PN; 9003466. Please do not disturb seal in retainer when removing from engine.~ Cummins Engineering is currently investigating the root cause of the oil leak concern. If there are any questions, please contact Chad Eichbrecht at cell (248) 309-2695~ If you do not receive a response within 15 minutes, please proceed with normal repair
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MY16 RA3 & RA4 Replacement Radios All MY16 RA3 and RA4 replacement radios must be ordered through the exchange process at United Radio. DO NOT order a NEW radio from Mopar. Go back and order a "Z" level part number. (example: Z8249986A$) The MY16 replacement radios must be reconfigured by United Radio to the wireless network provider in order for Uconnect Apps to work properly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Housing: Oil Filter Adapter Cummins equipped trucks ONLY; If you are replacing the oil filter adapter as a result of thread damage to the oil filter connector (Spud), DO NOT replace the entire adapter assembly. The oil filter connector is available separately (Part Number 04429355).~ If ordering an adapter due to some other issue, you must also order an oil bypass valve Mopar Part # 04797726AB, as these are not reusable. Please refer to all applicable published service information for oil bypass valve installation
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with updated software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set: · **P0335 - Crankshaft Position Sensor Circuit. · P2610 - PCM Internal Engine Off Timer Performance.** · P0456 - EVAP System Small Leak.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 6.4L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs: · **P0335 - Crankshaft Position Sensor Circuit. · P2610 - PCM Internal Engine Off Timer Performance.** · P0456 - EVAP System Small Leak. · P3402 - Cylinder 1 Deactivation Control Performance. · P3426 - Cylinder 4 Deactivation Control Performance. · P3442 - Cylinder 6 Deactivation Control Performance. · P3450 - Cylinder 7 Deactivation Control Performance. · P2610 - PCM Internal Engine Off Timer Performance set in the PCM memory. In addition to the DTCs listed above, the software update will improve: · **Correct an issue related to rounding of the cruise control set speed displayed in the cluster. · Brake Throttle Override calibration has changed to be less sensitive. · Throttle Body supplier change has caused a widening of the minimum and maximum voltage limits · Correct a software issue with oil pressure light function at key-up. · Correct a software issue related to idle timer. · Correct a software issue with inconsistent engine RPM increments/decrements with operator idle speed.(DD/DF/DP ONLY).** · Improved Cruise Control Acceleration mode. · Improved Multi Displacement System operation 6-Speed Automatic 66RFE transmission (Sales Code DFP). · Multi Displacement System function improved while in PTO stationary mode. 6-Speed Auto Aisin AS66RC transmission (Sales Code DF3). · Potential small improvement in fuel economy at higher altitudes. · Potential improvement in high altitude engine idle RPM stability. · EGR monitor status function.
Source components: ELECTRICAL SYSTEM · POWER TRAIN · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Intake Manifold Gasket Intake Manifold Gaskets on Pentastar Upgrade (Sales Code ERC/ERF) are reusable provided they are not cut, torn or melted. The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission Torque Converter Replacement After Drone Noise Verification This bulletin involves test driving the vehicle to listen for audible ?drone? noise at approximately 2,000 RPM. If drone noise is verified, normal torque converter replacement should be performed. The customer may describe a ?heavy droning noise? coming from the vehicle at an engine speed range of 1,800 RPM to 2,000 RPM with mid to deep throttle applied.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AS69RC Transmission For DD, DF, and DP Models ONLY; Code P2757 ? TCC PRESSURE CONTROL SOLENOID CONTROL CIRCUIT PERFORMANCE~ Transmission Part Numbers: RL300150AA [4x4], or RL300149AA [4x2 LHS PTO], RL300152AB 4x2 RHS PTO]~ If you are ordering an Aisin Transmission AS69RC [sales code DF2] for replacement due to code P2757 present [for 2016MY only] with the following symptoms:~ 1. Code P2757 with MIL on [Check engine light on]~ 2. Harness check is good~ 3. Vehicle build dates are from 10/15/2015 to 4/17/2016~ 4. Low miles - approximately below 1500 miles.~ Suggested repair actions:~ 1. Clear the code and test drive with light throttle attempting to engage torque converter lock up. The code P2757 will set, if torque converter lock up fails.~ 2. If the code P2757 returns: Replace Torque Converter [Part number RL335702AA] only.~ 3. Return the suspect Torque converter to FCA for review. [Follow Part retention process]
Source components: AIR BAGS · POWER TRAIN · SEAT BELTS · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Keyfob 2016 Vehicle Keyfobs with Passive Entry Keyless Go Feature - Engineering is investigating a keyfob unable to program or no function or low keyfob coin battery condition.~ Prior to replacing keyfob on MY16 vehicles, please contact Raja Charabuddi on cell (248) 202-7313. If no response within 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fan Support Assembly, Fan Support Bearing, Fan Pulley If you are replacing this part due to fan hub bearing failure, please also replace the fan clutch assembly using current Mopar stock (part number 52014729A$).~ Once installed, contact Christine Donegan at (866) 799-1692 ext 1257 to initiate a fast track request for the return of the parts for analysis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RamBox Lid Left Applique Loose This bulletin involves inspecting and if necessary, replacing the affected 6`4? RamBox lid applique. The customer may describe what appears to be a gap between the left applique and the RamBox lid. Applique may separate at lid, due to insufficient adhesive bond strength.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AS69RC Transmission For DD, DF, and DP Models ONLY; Code P2757 ? TCC PRESSURE CONTROL SOLENOID CONTROL CIRCUIT PERFORMANCE~ Transmission Part Numbers: RL300150AA [4x4], or RL300149AA [4x2 LHS PTO], RL300152AB 4x2 RHS PTO]~ If you are ordering an Aisin Transmission AS69RC [sales code DF2] for replacement due to code P2757 present [for 2016MY only] with the following symptoms:~ 1. Code P2757 with MIL on [Check engine light on]~ 2. Harness check is good~ 3. Vehicle build dates are from 10/15/2015 to 4/17/2016~ 4. Low miles - approximately below 1500 miles.~ Suggested repair actions:~ 1. Clear the code and test drive with light throttle attempting to engage torque converter lock up. The code P2757 will set, if torque converter lock up fails.~ 2. If the code P2757 returns: Replace Torque Converter [Part number RL335702AA] only.~ 3. Return the suspect Torque converter to FCA for review. [Follow Part retention process]
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fan Support Assembly, Fan Support Bearing, Fan Pulley If you are replacing this part due to fan hub bearing failure, please also replace the fan clutch assembly using current Mopar stock (part number 52014729A$).~ Once installed, contact Christine Donegan at (866) 799-1692 ext 1257 to initiate a fast track request for the return of the parts for analysis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RamBox Lid Left Applique Loose This bulletin involves inspecting and if necessary, replacing the affected 6`4? RamBox lid applique. The customer may describe what appears to be a gap between the left applique and the RamBox lid. Applique may separate at lid, due to insufficient adhesive bond strength.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"AS69RC TRANSMISSION FOR DD, DF, AND DP MODELS ONLY; CODE P2757 TCC PRESSURE CONTROL SOLENOID CONTROL CIRCUIT PERFORMANCE~ TRANSMISSION PART NUMBERS: RL300150AA [4X4], OR RL300149AA [4X2 LHS PTO], RL300152AB 4X2 RHS PTO]~ IF YOU ARE ORDERING AN AISIN TRANSMISSION AS69RC [SALES CODE DF2] FOR REPLACEMENT DUE TO CODE P2757 PRESENT [FOR 2016MY ONLY] WITH THE FOLLOWING SYMPTOMS:~ 1. CODE P2757 WITH MIL ON [CHECK ENGINE LIGHT ON]~ 2. HARNESS CHECK IS GOOD~ 3. VEHICLE BUILD DATES ARE FROM 10/15/2015 TO 4/17/2016~ 4. LOW MILES - APPROXIMATELY BELOW 1500 MILES.~ SUGGESTED REPAIR ACTIONS:~ 1. CLEAR THE CODE AND TEST DRIVE WITH LIGHT THROTTLE ATTEMPTING TO ENGAGE TORQUE CONVERTER LOCK UP. THE CODE P2757 WILL SET, IF TORQUE CONVERTER LOCK UP FAILS.~ 2. IF THE CODE P2757 RETURNS: REPLACE TORQUE CONVERTER [PART NUMBER RL335702AA] ONLY.~ 3. RETURN THE SUSPECT TORQUE CONVERTER TO FCA FOR REVIEW. [FOLLOW PART RETENTION PROCESS]"
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"FAN SUPPORT ASSEMBLY, FAN SUPPORT BEARING, FAN PULLEY IF YOU ARE REPLACING THIS PART DUE TO FAN HUB BEARING FAILURE, PLEASE ALSO REPLACE THE FAN CLUTCH ASSEMBLY USING CURRENT MOPAR STOCK (PART NUMBER 52014729A$).~ ONCE INSTALLED, CONTACT CHRISTINE DONEGAN AT (866) 799-1692 EXT 1257 TO INITIATE A FAST TRACK REQUEST FOR THE RETURN OF THE PARTS FOR ANALYSIS."
Source components: POWER TRAIN:DRIVELINE:CENTER SUPPORT BEARING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68143886AA. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68174065AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 04685719AI. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part numbers: 68141880AH, 68141881AH, 68145625AI, 68145626AI, 68189480AF and replacement part numbers are 68141880AI, 68141881AI, 68145625AJ, 68145626AJ & 68189480AG respectively,which arein stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part number: 05278632AF and replacement part number is 52030379AA which isin stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part numbers: 1YG06JSCAC, 1YG06KEPAC, 1YG 06KFSAC, 1YG 06KGZAC, 1YG 06KBUAC and replacement part numbers are 1YG 1YG06KFSAD, 1YG 06KG ZAD, 1YG 06KBUAE respectively,which arein stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part number: 68188889AE and replacement part number is 68188889AF which isin stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Return: ALTERNATOR - ENGINE You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part numbers: R4801313AC replacement part number are 04801313AD respectively which are in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 8 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of following part numbers: 68036213AA, 68036230AF, 68158196AC, 68158197AD, & 68158454AD. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
68085119AE,Inspect and Return: Exhaust Pipe Assy - Frt W/Catalytic Converter You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68085119AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ignition Node Module Replacement This bulletin involves replacing the ignition node module. Some customers may experience a no start issue when turning the key fob in the ignition node module(Fig. 1).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ignition Node Module Replacement This bulletin involves replacing the ignition node module. Some customers may experience a no start issue when turning the key fob in the ignition node module(Fig. 1).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Integrated Center Stack If vehicle is found within 50 mile radius of the Detroit Metro area please hold vehicle and contact:~ Contact one of the following:~ Daniel Acciacca CELL (586) 709-1537~ Michael Savich CELL (248) 214-7270~ Ayed Hadaad CELL (248) 941-8707~ Issue: On a 2015 & 2016MY LA (Challenger), LD(Charger) and LX (300), the Integrated Center Stack (ICS) may experience a lock-up/Inop condition (complete loss of functionality) during any vehicle diagnostic session (reading fault codes, clearing fault codes, reflashing of any module, etc.). If this occurs, do not replace the ICS. The module functionality can be restored if it is reset by disconnecting power to it (by removing fuse, battery disconnect or module connector disconnect).~
NHTSA source summary · Original PDF not reviewed by Recallfolio
A/C Compressor This applies to 2015 and 2016 UF and PF. Before replacing the AC compressor for noise, leaks , or in-op:~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ 1) Check all AC plumbing connection for leaks with UV light. Any leaks found?~ 2) Does compressor pulley and clutch hub turn freely, or are they seized?~ 3) What was the amount of the recovered refrigerant?~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ If the compressor is replaced, then:~ 4) Drain oil from compressor. What was quantity of oil recovered?
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hands Free Module - CTM ? Peiker For RT, JK and MK bodies only; Before replacing the Hands Free Module (HFM), please contact Gaurav Saxena at cell (248) 260-0583~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Battery - Transmitter For vehicles within 12 Months in Service which have a "FOB Battery Low" message within Cluster or DTC B1A10 or B1A11 Active or Stored. Engineering is requesting complete FOB returned unopened (ie, battery not removed or FOB housing opened!). ~ All others, follow normal procedures.~ Please ensure Dealer Technicians are aware of this request to allow for gain in FOB Battery depletion understanding.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diagnosing A Urea Module That Is Exposed To Diesel Fuel This bulletin involves discussing what will happen to the rubber material used in the urea pump when exposed to diesel fuel. This unit is sometimes referred to as the Selective Catalyst Reductant (SCR) module or the Adblue Delivery Module (ADM). Units exposed to hydrocarbons have a particular failure mode, the rubber heater unit is crinkled and in some cases the metal heater protrudes through the rubber membrane. The rubber material used in this unit is designed to withstand Diesel Exhaust Fluid (DEF) only. Exposure to fluids that contain hydrocarbons (i.e. diesel fuel) will damage the unit beyond repair. Units returned that exhibit this failure mode will have warranty claims that are rejected. Units that exhibit this failure mode should be considered customer abuse and should not be covered under warranty. Use the Hydroscopic test paper (P/N 223-44-863) available through MoparEssentialTools.com to confirm exposure.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diagnosing A Urea Module That Is Exposed To Diesel Fuel This bulletin involves discussing what will happen to the rubber material used in the urea pump when exposed to diesel fuel. This unit is sometimes referred to as the Selective Catalyst Reductant (SCR) module or the Adblue Delivery Module (ADM). Units exposed to hydrocarbons have a particular failure mode, the rubber heater unit is crinkled and in some cases the metal heater protrudes through the rubber membrane. The rubber material used in this unit is designed to withstand Diesel Exhaust Fluid (DEF) only. Exposure to fluids that contain hydrocarbons (i.e. diesel fuel) will damage the unit beyond repair. Units returned that exhibit this failure mode will have warranty claims that are rejected. Units that exhibit this failure mode should be considered customer abuse and should not be covered under warranty. Use the Hydroscopic test paper (P/N 223-44-863) available through MoparEssentialTools.com to confirm exposure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to a two trip fault: · P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. · P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. · P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. · P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: · P0128 - Thermostat Rationality Improvements. · P2281 - Air Leak Between MAF and Throttle Body. · P218F - Reductant No Flow Detected. · P0218 - Transmission High Temperature Operation Activated (68RFE Only). · P0868 - Line Pressure Low, MIL Action (68RFE Only). · U110E - Lost Ambient Temperature Message. · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · Engine Noise Improvements. · Engine Hesitation Improvement. · Improved Engine Fuel Economy. · Reduction in engine noise during regeneration at idle. · 68RFE Transmission Overall Shift Quality Improvements. · Test results fix for partial range misfire (68RFE Only). · Ambient Air Temperature Improvements. · Stationary Desoot with wiTECH Fix. · OBD Misfire Monitoring Improvement (68RFE Only).
Source components: ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM) · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to a two trip fault: · P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. · P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. · P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. · P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: · P0128 - Thermostat Rationality Improvements. · P2281 - Air Leak Between MAF and Throttle Body. · P218F - Reductant No Flow Detected. · P0218 - Transmission High Temperature Operation Activated (68RFE Only). · P0868 - Line Pressure Low, MIL Action (68RFE Only). · U110E - Lost Ambient Temperature Message. · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · Engine Noise Improvements. · Engine Hesitation Improvement. · Improved Engine Fuel Economy. · Reduction in engine noise during regeneration at idle. · 68RFE Transmission Overall Shift Quality Improvements. · Test results fix for partial range misfire (68RFE Only). · Ambient Air Temperature Improvements. · Stationary Desoot with wiTECH Fix. · OBD Misfire Monitoring Improvement (68RFE Only).
Source components: BACK OVER PREVENTION · EXTERIOR LIGHTING · FUEL SYSTEM, GASOLINE · POWER TRAIN · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to a two trip fault: · P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. · P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. · P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. · P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: · P0128 - Thermostat Rationality Improvements. · P2281 - Air Leak Between MAF and Throttle Body. · P218F - Reductant No Flow Detected. · P0218 - Transmission High Temperature Operation Activated (68RFE Only). · P0868 - Line Pressure Low, MIL Action (68RFE Only). · U110E - Lost Ambient Temperature Message. · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · Engine Noise Improvements. · Engine Hesitation Improvement. · Improved Engine Fuel Economy. · Reduction in engine noise during regeneration at idle. · 68RFE Transmission Overall Shift Quality Improvements. · Test results fix for partial range misfire (68RFE Only). · Ambient Air Temperature Improvements. · Stationary Desoot with wiTECH Fix. · OBD Misfire Monitoring Improvement (68RFE Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Speakers: For 2016 speakers issues (all bodies), before replacing this part please contact one of the following people regarding this repair: Mahmoud (Mo) Touha at cell (248) 705-3934. If no response is received within 15 minutes, then please proceed with repair.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Power Fold Rearview Mirror Prior to replacing this part for a loose mirror, please first follow this procedure to reset the pivot mechanism. Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.
NHTSA source summary · Original PDF not reviewed by Recallfolio
9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Speakers: For 2016 speakers issues (all bodies), before replacing this part please contact one of the following people regarding this repair: Mahmoud (Mo) Touha at cell (248) 705-3934. If no response is received within 15 minutes, then please proceed with repair.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Power Fold Rearview Mirror Prior to replacing this part for a loose mirror, please first follow this procedure to reset the pivot mechanism. Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.
Source components: PARKING BRAKE · POWER TRAIN · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Power Fold Rearview Mirror Prior to replacing this part for a loose mirror, please first follow this procedure to reset the pivot mechanism. Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Center Console Lid Binding This bulletin involves adding a rubber bumper to the console lid to prevent the lid from binding. **This bulletin will help prevent a binding or an audible clicking noise in the center console lid. NOTE: Do not attempt to fix a center console lid that has an existing binding or audible condition by adding the bumper.**
NHTSA source summary · Original PDF not reviewed by Recallfolio
Center Console Lid Binding This bulletin involves adding a rubber bumper to the console lid to prevent the lid from binding. **This bulletin will help prevent a binding or an audible clicking noise in the center console lid. NOTE: Do not attempt to fix a center console lid that has an existing binding or audible condition by adding the bumper.**
NHTSA source summary · Original PDF not reviewed by Recallfolio
Center Console Lid Binding This bulletin involves adding a rubber bumper to the console lid to prevent the lid from binding. **This bulletin will help prevent a binding or an audible clicking noise in the center console lid. NOTE: Do not attempt to fix a center console lid that has an existing binding or audible condition by adding the bumper.**
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following DTCs have been changed from a one trip fault to a two trip fault: · P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. · P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. · P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. · P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: · **P0128 - Thermostat Rationality Improvements.** · P2281 - Air Leak Between MAF and Throttle Body. · P218F - Reductant No Flow Detected. · P0218 - Transmission High Temperature Operation Activated (68RFE Only). · P0868 - Line Pressure Low, MIL Action (68RFE Only). · U110E - Lost Ambient Temperature Message. · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · **Engine Noise Improvements. · Engine Hesitation Improvement. · Improved Engine Fuel Economy.** · Reduction in engine noise during regeneration at idle. · 68RFE Transmission Overall Shift Quality Improvements. · Test results fix for partial range misfire (68RFE Only). · Ambient Air Temperature Improvements. · Stationary Desoot with wiTECH Fix. · OBD Misfire Monitoring Improvement (68RFE Only).
Source components: BACK OVER PREVENTION · EXTERIOR LIGHTING · FUEL SYSTEM, GASOLINE · POWER TRAIN · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following DTCs have been changed from a one trip fault to a two trip fault: · P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. · P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. · P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. · P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: · **P0128 - Thermostat Rationality Improvements.** · P2281 - Air Leak Between MAF and Throttle Body. · P218F - Reductant No Flow Detected. · P0218 - Transmission High Temperature Operation Activated (68RFE Only). · P0868 - Line Pressure Low, MIL Action (68RFE Only). · U110E - Lost Ambient Temperature Message. · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · **Engine Noise Improvements. · Engine Hesitation Improvement. · Improved Engine Fuel Economy.** · Reduction in engine noise during regeneration at idle. · 68RFE Transmission Overall Shift Quality Improvements. · Test results fix for partial range misfire (68RFE Only). · Ambient Air Temperature Improvements. · Stationary Desoot with wiTECH Fix. · OBD Misfire Monitoring Improvement (68RFE Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following DTCs have been changed from a one trip fault to a two trip fault: · P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. · P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. · P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. · P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: · **P0128 - Thermostat Rationality Improvements.** · P2281 - Air Leak Between MAF and Throttle Body. · P218F - Reductant No Flow Detected. · P0218 - Transmission High Temperature Operation Activated (68RFE Only). · P0868 - Line Pressure Low, MIL Action (68RFE Only). · U110E - Lost Ambient Temperature Message. · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · **Engine Noise Improvements. · Engine Hesitation Improvement. · Improved Engine Fuel Economy.** · Reduction in engine noise during regeneration at idle. · 68RFE Transmission Overall Shift Quality Improvements. · Test results fix for partial range misfire (68RFE Only). · Ambient Air Temperature Improvements. · Stationary Desoot with wiTECH Fix. · OBD Misfire Monitoring Improvement (68RFE Only).
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
CABLE ASSY, Power Sliding Backlite For MY16 DS, DJ, DD, DP, D2 trucks. Prior to replacing a Power Sliding Backlight Cable Assembly, please contact Marc Galli by cell phone at (248) 941-8402 as he would like to gather information. In addition, if the dealership is within the Metro Detroit Area, Marc would like to analyze the vehicle in person prior to it being repaired. If Marc cannot be contacted within 15 minutes, please provide pictures of the inside lower rail of the glass to confirm (2 passenger side and 1 driver side) cable clips are fully seated as well as pictures of the (2) regulator motor cable spring plungers to confirm they are also seated. Then proceed with the repair. Please email pictures to Marc at marc.galli@fcagroup.com.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CABLE ASSY, Power Sliding Backlite For MY16 DS, DJ, DD, DP, D2 trucks. Prior to replacing a Power Sliding Backlight Cable Assembly, please contact Marc Galli by cell phone at (248) 941-8402 as he would like to gather information. In addition, if the dealership is within the Metro Detroit Area, Marc would like to analyze the vehicle in person prior to it being repaired. If Marc cannot be contacted within 15 minutes, please provide pictures of the inside lower rail of the glass to confirm (2 passenger side and 1 driver side) cable clips are fully seated as well as pictures of the (2) regulator motor cable spring plungers to confirm they are also seated. Then proceed with the repair. Please email pictures to Marc at marc.galli@fcagroup.com.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. As per regulatory compliance: Please return follow ing stock of part numbers: 82214711, 82214712, 82214713, 82214714, 82214715, 82214716, 82214717, 82214718, 82214720, 82214721, 82214722, 82214723, 82214724, 82214725, 82214726, 82214727, 82214728, 82214729, 82214730, 82214731, 82214732. Please return parts back to your facing depot using Return Code 02, before 31May, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of part number 68288760AA. Replacement part number is 68288760AB. Replacement parts w ill be available w eek ending 5/6/16. Please return suspect parts back to your facing depot using Return Code 02, before 26 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA3 RA4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: · Navigation failed message is displayed. · Clock not automatically updating to local time. · Poor or no connection to cellular network. · HVAC temperature out of sync with radio display (KL vehicles). · Display goes blank/black. · Radio locks up. · Some Uconnect App remote commands do not execute with the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA3 RA4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: · Navigation failed message is displayed. · Clock not automatically updating to local time. · Poor or no connection to cellular network. · HVAC temperature out of sync with radio display (KL vehicles). · Display goes blank/black. · Radio locks up. · Some Uconnect App remote commands do not execute with the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part numbers: 68003062AB, 68003083AB, 68003085AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 24 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part numbers: 1PE001W 7AB, 1PE011W 7AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 24 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT: RA3 RA4 Radio Enhancements OVERVIEW: This bulletin involves inspecting and, if required, updating the radio software. SYMPTOM/CONDITION: A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT: RA3 RA4 Radio Enhancements OVERVIEW: This bulletin involves inspecting and, if required, updating the radio software. SYMPTOM/CONDITION: A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Headlamps May Be Out Of Adjustment Or Alignment This bulletin involves adjusting the headlamps to specified alignment. The customer may describe that the headlamps are out of alignment or oncoming vehicles are flashing their bright lights at them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Air Suspension Control Module (ASCM) System Enhancements This Bulletin involves updating the (ASCM) software. A customer may describe the following: · **Cluster stays awake after ignition is turned off for 10 minutes or more.** · False message Battery Voltage Low - Start Engine to Change Ride Height which appears in the Electronic Vehicle Information Center (EVIC). This condition may happen when the vehicle is first started and trying to move the suspension from trailer ride height to normal ride height.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT: Headlamps May Be Out Of Adjustment Or Alignment. OVERVIEW: This bulletin involves adjusting the headlamps to specified alignment. SYMPTOM/CONDITION: The customer may describe that the headlamps are out of alignment or oncoming vehicles are flashing their bright lights at them.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING:HEADLIGHTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT: Flash: Air Suspension Control Module (ASCM) System Enhancements SYMPTOM/CONDITION: A customer may describe the following: · **Cluster stays awake after ignition is turned off for 10 minutes or more.** · False message Battery Voltage Low - Start Engine to Change Ride Height which appears in the Electronic Vehicle Information Center (EVIC). This condition may happen when the vehicle is first started and trying to move the suspension from trailer ride height to normal ride height.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT: Headlamps May Be Out Of Adjustment Or Alignment. OVERVIEW: This bulletin involves adjusting the headlamps to specified alignment. SYMPTOM/CONDITION: The customer may describe that the headlamps are out of alignment or oncoming vehicles are flashing their bright lights at them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT: Flash: Air Suspension Control Module (ASCM) System Enhancements OVERVIEW: This Bulletin involves updating the (ASCM) software. SYMPTOM/CONDITION: A customer may describe the following: **Cluster stays awake after ignition is turned off for 10 minutes or more.** False message Battery Voltage Low - Start Engine to Change Ride Height which appears in the Electronic Vehicle Information Center (EVIC). This condition may happen when the vehicle is first started and trying to move the suspension from trailer ride height to normal ride height.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Radio Frequency Hub Module (RFHM) Enhancement This bulletin involves updating the RFHM software. Customers may describe the instrument cluster is illuminating by itself after the ignition has been off for an extended period of time (10 minutes or more).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT: Flash: Radio Frequency Hub Module (RFHM) Enhancement SYMPTOM/CONDITION: Customers may describe the instrument cluster is illuminating by itself after the ignition has been off for an extended period of time (10 minutes or more).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT: Flash: Radio Frequency Hub Module (RFHM) Enhancement SYMPTOM/CONDITION: Customers may describe the instrument cluster is illuminating by itself after the ignition has been off for an extended period of time (10 minutes or more).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Roof Damage Repair This bulletin involves identifying and repairing scratches in the paint on left side of roof. The customer may describe scratches on the driver?s side of roof.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Center Console Lid Binding This bulletin involves adding a rubber bumper to the console lid to prevent the lid from binding. The customer may describe a binding or audible clicking condition when the center console lid is being opened or closed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. DTCs have been changed from a one trip fault to a two trip fault: · **P0421 - Catalyst 1 Efficiency Below Threshold Bank 1.** · P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. · P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. · P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · P2281 - Air Leak Between MAF and Throttle Body. · P218F - Reductant No Flow Detected. · P0218 - Transmission High Temperature Operation Activated (68RFE Only). · P0868 - Line Pressure Low, MIL Action (68RFE Only). · U110E - Lost Ambient Temperature Message. · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · **Reduction in engine noise during regeneration at idle.** · 68RFE Transmission Overall Shift Quality Improvements. · Test results fix for partial range misfire (68RFE Only). · Ambient Air Temperature Improvements. · Stationary Desoot with wiTECH Fix. · OBD Misfire Monitoring Improvement (68RFE Only).
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:ENGINE:DIESEL · EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. These DTCs have been changed from a one trip fault to a two trip fault: · P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. · P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. · P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. · P207F - Reductant Quality Performance. · P218F - Reductant No Flow Detected. · U110E - Lost Ambient Temperature Message. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · Ambient Air Temperature Improvements. · Stationary de-soot with WiTech fix.
Source components: BACK OVER PREVENTION · EXTERIOR LIGHTING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. These DTCs have been changed from a one trip fault to a two trip fault: · P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. · P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. · P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. · P207F - Reductant Quality Performance. · P218F - Reductant No Flow Detected. · U110E - Lost Ambient Temperature Message. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · Ambient Air Temperature Improvements. · Stationary de-soot with WiTech fix.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. **These DTCs have been changed from a one trip fault to a two trip fault: · P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF · P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low · P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High** A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · **P2281 - Air Leak Between MAF and Throttle Body. · P218F - Reductant No Flow Detected. · P0218 - Transmission High Temperature Operation Activated (68RFE Only). · P0868 - Line Pressure Low, MIL Action (68RFE Only).** · U110E - Lost Ambient Temperature Message. · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · **68RFE Transmission Overall Shift Quality Improvements. · Test results fix for partial range misfire (68RFE). · Ambient Air Temperature Improvements. · Stationary Desoot with wiTECH Fix.** · OBD Misfire Monitoring Improvement (68RFE Only).
Source components: FUEL SYSTEM, GASOLINE · POWER TRAIN · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. **These DTCs have been changed from a one trip fault to a two trip fault: · P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF · P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low · P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High** A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · **P2281 - Air Leak Between MAF and Throttle Body. · P218F - Reductant No Flow Detected. · P0218 - Transmission High Temperature Operation Activated (68RFE Only). · P0868 - Line Pressure Low, MIL Action (68RFE Only).** · U110E - Lost Ambient Temperature Message. · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · **68RFE Transmission Overall Shift Quality Improvements. · Test results fix for partial range misfire (68RFE). · Ambient Air Temperature Improvements. · Stationary Desoot with wiTECH Fix.** · OBD Misfire Monitoring Improvement (68RFE Only).