Original record summaries, dates and identifiers for this model-year. Records 101–173 of 173, ordered newest first. Dated records on this page: Sep 25, 2017–Feb 4, 2020.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Feb 4, 2020Service Bulletin/Repair Instructions
NTB15-049t
NHTSA communication ID: 10172232
NHTSA source summary · Original PDF not reviewed by Recallfolio
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2017-2019 TITAN/TITAN XD KING CAB; WIND NOISE AT 40 MPH AND ABOVE IF YOU CONFIRM A wind noise coming from the front door area that has the following characteristics: ï· - Occurs at 40 mph and above. ï· - The wind noise is heard from the left and/or right side of the vehicle. ï· - The wind noise may be heard near the rear edge of the front door window or near the front edge of the rear door window. ACTION Replace the sash moldings on both sides of the vehicle with the parts listed in PARTS INFORMATION on the last page of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2015-2019 MURANO AND 2016-2019 TITAN; CLIMATE CONTROLLED SEAT INOPERATIVE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2018 ARMADA AND TITAN; MIL ON WITH DTC P0138 AND/OR P0158 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on page 5. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.
NHTSA source summary · Original PDF not reviewed by Recallfolio
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016 â 2018 TITAN XD; STATIC DISCHARGE FROM FUEL LINE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ENGINE KNOCK OR TICK NOISE IF YOU CONFIRM A knock or tick noise is coming from the engine Or The customer states a knock or tick noise is heard from the engine area. ACTION Refer to REPAIR OVERVIEW on page 3.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016 - 2018 TITAN XD; STATIC DISCHARGE FROM FUEL LINE IF YOU CONFIRM There is a static discharge from the fuel line causing a click or pop noise. NOTE: Concern is more likely to: - Be heard from under the center of vehicle. - Occur more often on dry days. - Occur at regular intervals about every 30 seconds to 1 minute. ACTION Install the tether assembly as described in the SERVICE PROCEDURE starting on the next page.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2019 TITAN/TITAN XD; WHISTLE NOISE WHEN REFUELING This bulletin applies only to vehicles equipped with a gasoline V8 engine. IF YOU CONFIRM A whistle noise is heard when refueling the vehicle. ACTION Replace the fuel tank with the new one listed in the PARTS INFORMATION section of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2019 TITAN; MIL ON WITH DTC P0448 AND WATER IN EVAP FILTER IF YOU CONFIRM The MIL is ON with DTC P0448 (EVAP canister vent control valve close) stored in the ECM and water is found in the EVAP filter, canister, or vent control valve ACTION Remove and replace the: - Fuel filler tube. - EVAP filter. - EVAP canister. - EVAP vent control valve. - EVAP pressure sensor. IMPORTANT: Before any parts are removed from the vehicle, note the EVAP filter orientation and hose routing (take a photo). Hose routing and EVAP filter orientation is critical and varies depending on production date.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2018-2019 TITAN XD; WHISTLE NOISE FROM VEHICLE FRONT AT 60 MPH AND ABOVE IF YOU CONFIRM A whistle type noise heard from the vehicle front at speeds of 60 MPH and above. ACTION 1. Confirm the source of the whistle noise by referring to steps 1 and 2 of the SERVICE PROCEDURE on the next page. 2. If the whistle noise stops after applying the tape, replace the grille-to-hood seal with the new one listed in the PARTS INFORMATION on the last page of this bulletin. 3. Ensure the hood is adjusted correctly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016 ? 2019 TITAN AND TITAN XD; STEP RAIL END CAP CHROME TRIM AVAILABLE AS SEPARATE PART This bulletin applies only to Crew Cab models. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; P0171 AND P0174 SERVICE INFORMATION SERVICE INFORMATION Diagnosis for DTCs P0171 (FUEL SYS LEAN B1) and P0174 (FUEL SYS LEAN B2) have been revised for the APPLIED VEHICLES listed above. When performing diagnosis for either of these DTCs, start by using the SERVICE PROCEDURE section of this bulletin. NOTE: The related Electronic Service Manuals (ESM) will be revised in the future to include these diagnostic steps.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; MIL ON WITH DTC P219A AND/OR P219B STORED This bulletin applies to Titan XD vehicles equipped with a VK56D gas engine only. SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016 ? 2018 TITAN XD; MIL ON WITH DTC P2048 STORED This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM The MIL is ON and DTC P2048 (REDUCTANT INJECTION VALVE CIRCUIT LOW 1/1) is stored. ACTION Reprogram the ECM per the SERVICE PROCEDURE in this bulletin. - Refer to SERVICE PROCEDURE on the next page to confirm if reprogramming is needed. - Save Computer Data with CONSULT-III plus (C-III plus). - If this bulletin applies, continue with ECM Reprogramming procedure. - Write Saved Data with CONSULT-III plus.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2019 TITAN XD DIESEL; MIL ON WITH DTC P0299 FOR BOOST PRESSURE This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM The MIL is ON with DTC P0299 (BOOST PRESSURE) stored And - The engine air cleaner box and air filter: - Are free from debris - Are not damaged or have any restrictions - The engine charge air cooler tube clamps are tight and tubes are free from leaks at the following locations: - The turbocharger compressor outlet - The charge air cooler inlet - The charge air cooler outlet - The intake manifold inlet - The Boost Pressure Absolute is within +/- 1.5 PSI of ambient air pressure with ignition ON and engine OFF (observed in Data Monitor). ACTION Refer to Repair Overview on page 2.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 TITAN/TITAN XD WITH AUTO A/C; VAST TEMPERATURE DIFFERENCE BETWEEN 61°F & 62°F SETTINGS This bulletin applies only to vehicles equipped with auto A/C. IF YOU CONFIRM The customer states there is a significant difference in vent temperature between auto A/C settings of 61°F and 62°F. ACTION 1. Check the A/C auto amp?s current part number. 2. If the current part number matches one listed in Table A (see page 6), reprogram the A/C auto amp.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016 - 2018 TITAN XD; DEF SYSTEM PARTS AVAILABILITY This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 diesel engine. SERVICE INFORMATION When diagnosing any Diesel Exhaust Fluid (DEF) system component, refer to Table A below. These parts are now available separately. Do not replace the entire DEF tank assembly if the required part is shown in Table A.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2019 TITAN XD DIESEL; FUEL FILTER MAINTENANCE This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 diesel engine. SERVICE INFORMATION The Stage 1 and Stage 2 fuel filters must be replaced every 10,000 miles or a restriction may develop. DTCs P008A, P00C6, P0087 and/or a whining noise from the Stage 1 Fuel Filter Module may be present due to a restriction in the Stage 1 and/or Stage 2 fuel filters. NOTE: An inoperable or whining Stage 1 Fuel Filter Module that has not had the fuel filters regularly replaced as per the Owner?s Manual Maintenance schedule is not a warrantable repair. Before proceeding with any fuel system restriction diagnosis: - Confirm that both of the vehicle?s Stage 1 and Stage 2 fuel filters have been replaced at the correct service intervals, as per the Owner?s Manual Maintenance schedule. IMPORTANT: Warranty claim submissions for a Stage 1 Fuel Filter module will be denied if the Stage 1 and/or Stage 2 fuel filters have not been replaced per the Owner's Manual maintenance schedule.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 TITAN/TITAN XD; VISIBLE VIBRATION IN FRONT PASSENGER SEAT AT 60-80 MPH WHEN UNOCCUPIED IF YOU CONFIRM The front passenger seat has a visible vibration/movement that only occurs at speeds between 60 mph and 80 mph And Vibration/movement can be reproduced while driving on smooth roads (vibration/movement not caused by road surface) And All tires are in balance and road force vibration is within specifications (see NTB11-062). ACTION Replace the front passenger seatback assembly and front passenger headrest. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2015-2019 MURANO AND 2016-2019 TITAN; CLIMATE CONTROLLED SEAT INOPERATIVE IF YOU CONFIRM The driver or passenger side climate controlled seat: - Heating and cooling features do not operate And - The harness connector or control unit of the climate controlled seat appears as shown in Figure 3 or Figure 5. ACTION Perform the following to the affected seat: A. Replace the climate controlled seat control unit. B. Drill a hole for the new harness clip. C. Replace the harness connector of the climate controlled seat control unit. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Generator Harness Dealer Inventory This bulletin applies only to vehicles equipped with VK56 Engine Type. *****Dealer Announcement***** Nissan is conducting a quality action to inspect the generator harness on specific 2017-18 Titan vehicles in dealer inventory as identified in Service Comm. On some of the affected vehicles, the generator harness may have been pinched between the frame and the cylinder head. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. Nissan requests dealers to inspect all the affected vehicles, prior to sale to help ensure customer satisfaction. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History ? Open Campaigns I.D. PC673 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Dealers are asked to use the attached procedure to help ensure the generator wire is positioned correctly and confirm there is no damage from electrical arcing. - If the generator wire is or can be properly positioned and there are no signs of electrical arcing/damage, the vehicle may be immediately released for sale. - If there are signs of electrical arcing or damage, the VEHICLE MUST REMAIN ON HOLD AND CANNOT BE RETAILED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2018 TITAN CREW CAB AND TITAN XD CREW CAB; RUNNING BOARD LIGHT COVERED This bulletin applies only to vehicles equipped with a Dealer or Vehicle Processing Center (VPC) installed running board lighting kit. IF YOU CONFIRM The running board light near the middle of one or both running boards does not appear to light up (see Figures 1 and 2 on the next page) And The hole in the running board's reinforcement bracket does not line up with the running board light (the light is covered). ACTION Replace the running board on the side of the vehicle where the running board light does not appear to be lit up. * See PARTS INFORMATION to select the correct part. * For instructions on how to replace the running board(s), refer to ASIST > Model Titan > Year 2018. Select the Acc. Install Instructions tab, and then scroll down and select Running Board_Titan_999T6 W3xxx.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2019 TITAN XD; DIESEL FUEL DEF CONTAMINATION This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AIR BAG WARNING LIGHT FLASHING INDICATING SYSTEM DIAGNOSTIC MODE IF YOU CONFIRM The air bag warning light is flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2018 TITAN; IPDM E/R SERVICE INFORMATION SERVICE INFORMATION When diagnosing an electrical issue that involves the IPDM E/R, make sure to: - Check for blown fuses in the IPDM E/R. - Replace any blown fuses and recheck the issue. NOTE: - Do not replace an IPDM E/R if replacement of a fuse will resolve the issue. - Part numbers for IPDM E/R fuses are listed in the Parts Information on the next page. CLAIMS INFORMATION If the IPDM E/R is replaced, do not remove the fuses or any other components. The old part must be returned complete. An IPDM E/R that is returned with missing or physically damaged components will be charged back to the dealer.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR SERVICE INFORMATION Applied Vehicles listed above are no longer equipped with a door unlock sensor and/or Body Control Module (BCM) software to provide support for the door unlock sensor. Normal Functionality For Vehicles Built Without Door Unlock Sensor And/Or BCM Software To Support Door Unlock Sensor For Applied Vehicles built after the Applied Dates listed on page 1, using the mechanical key on the driver door will operate differently than vehicles built before the Applied Dates. For these later models, the BCM will not recognize operation of the mechanical key. If a mechanical key is used to lock the driver door: - The security system will not set. If the vehicle is broken into, the alarm will not sound. - Only the driver door will be locked. Other doors will not lock using the mechanical key. If a mechanical key is used to unlock the driver door: - Only the driver door will be unlocked. Other doors will not be unlocked. - If the security system is set, when the door is opened the alarm will sound. NOTE: Using the Unlock button on the Intelligent Key, pushing the request switch on the driver or passenger door with the Intelligent Key in range, or using the Intelligent Key to start the vehicle will silence the alarm. The mechanical key will not operate the power windows.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 TITAN/TITAN XD AND 2012-2018 NV1500/2500/3500; ANTENNA STANDARDIZATION SERVICE INFORMATION For the applied vehicles, the replacement antenna base and antenna mast styles have changed to a new style, shown in Figure 1. The old style has been discontinued. If for any reason the old style antenna base needs to be replaced, both the base and the mast must be replaced as a set with the new style shown in Figure 1. If the vehicle still has the old style antenna base, as shown in Figure 2, and only the mast is damaged, a replacement antenna mast can be ordered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 TITAN XD; DTC P207F AND DEF SYSTEM ERROR IS DISPLAYED ON THE VEHICLE INFORMATION DISPLAY This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. The Applied Vehicles section, Table A on page 7, and the DTC Confirmation procedure have been revised. No other changes have been made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2019 TITAN XD; STAGE 1 AND STAGE 2 FUEL FILTER ELEMENT REPLACEMENT This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. Changes were made on page 4, 6, and 12. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TELEMATICS SERVICE INFORMATION This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made to page 10 for 2018 Armada. Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TELEMATICS SERVICE INFORMATION This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made to page 10 for 2018 Armada. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. APPLIED VEHICLES has been updated. On page 2, the procedural steps under DTC B130C have been revised. Discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TITAN, ARMADA, NV; ENGINE OIL LEAK AT RIGHT SIDE BLOCK BALL PLUG This bulletin has been amended. The APPLIED VEHICLES section has been updated. No other changes have been made. Please discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 TITAN XD DIESEL; AIR CONDITIONING BLOWS HOT AIR AFTER EXTENDED IDLING OVER 100°F This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended to change the Classification number. No other changes have been made. Please discard previous versions of this bulletin.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2017-2018 TITAN; AIR CONDITIONING BLOWS HOT AIR AFTER EXTENDED IDLING OVER 100°F This bulletin has been amended to change the Classification number. No other changes have been made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin has been amended. The IF YOU CONFIRM section and software number has changed. No other changes have been made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 TITAN XD DIESEL; AIR CONDITIONING BLOWS HOT AIR AFTER EXTENDED IDLING OVER 100°F This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM Hot air starts to blow from the dash vents while the Air Conditioning is ON, under the following conditions: - After the engine has idled for an extended period with the vehicle in Drive (D-range). And - Ambient temperature outside the vehicle is 100°F (37.8°C) or more. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with the reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 TITAN XD DIESEL; AIR CONDITIONING BLOWS HOT AIR AFTER EXTENDED IDLING OVER 100°F This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM Hot air starts to blow from the dash vents while the Air Conditioning is ON, under the following conditions: - After the engine has idled for an extended period with the vehicle in Drive (D-range). And - Ambient temperature outside the vehicle is 100°F (37.8°C) or more. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with the reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 TITAN XD DIESEL; AIR CONDITIONING BLOWS HOT AIR AFTER EXTENDED IDLING OVER 100°F This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM Hot air starts to blow from the dash vents while the Air Conditioning is ON, under the following conditions: - After the engine has idled for an extended period with the vehicle in Drive (D-range). And - Ambient temperature outside the vehicle is 100°F (37.8°C) or more. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with the reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HEADLIGHT SYSTEM ERROR DIAGNOSTIC INFORMATION SERVICE INFORMATION - When diagnosing a Headlight System Error warning, and - Both headlamps are visually working correctly, - It may be difficult to determine the exact cause. - Use the information in this bulletin as an aid, along with the Electronic Service Manual (ESM), to isolate the root cause and fix it right the first time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HEADLIGHT SYSTEM ERROR DIAGNOSTIC INFORMATION SERVICE INFORMATION - When diagnosing a Headlight System Error warning, and - Both headlamps are visually working correctly, - It may be difficult to determine the exact cause. - Use the information in this bulletin as an aid, along with the Electronic Service Manual (ESM), to isolate the root cause and fix it right the first time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HEADLIGHT SYSTEM ERROR DIAGNOSTIC INFORMATION SERVICE INFORMATION - When diagnosing a Headlight System Error warning, and - Both headlamps are visually working correctly, - It may be difficult to determine the exact cause. - Use the information in this bulletin as an aid, along with the Electronic Service Manual (ESM), to isolate the root cause and fix it right the first time.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING:HEADLIGHTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2017-2018 TITAN; AIR CONDITIONING BLOWS HOT AIR AFTER EXTENDED IDLING OVER 100°F IF YOU CONFIRM Hot air starts to blow from the dash vents while the Air Conditioning is ON, under the following conditions: - After the engine has idled for an extended period with the vehicle in Drive (D-range). And - Ambient temperature outside the vehicle is 100°F (37.8°C) or more. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2017-2018 TITAN; AIR CONDITIONING BLOWS HOT AIR AFTER EXTENDED IDLING OVER 100°F IF YOU CONFIRM Hot air starts to blow from the dash vents while the Air Conditioning is ON, under the following conditions: - After the engine has idled for an extended period with the vehicle in Drive (D-range). And - Ambient temperature outside the vehicle is 100°F (37.8°C) or more. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin applies only to vehicles equipped with navigation system. This bulletin has been amended to correct Bosch contact information on page 2. No other changes have been made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin applies only to vehicles equipped with navigation system. IF YOU CONFIRM One or more of the following is occurring: - The navigation unit intermittently reboots: - At random or while listening to SXM or on a Bluetooth hands-free phone call. - Loud booming noise from speakers while on a Bluetooth hands-free call. - Navigation unit screen illumination does not change at night as designed. - AM/FM signal strength issues. - A status message ?Voice Recognition is initializing, please wait? is displayed when pressing the voice recognition button 2-3 minutes after the ignition is first turned ON. NOTE: If the message is displayed within the first 2-3 minutes this is normal. The voice recognition is loading phonebook contacts into its system. AND - The Software version has been confirmed as ?needs update? (refer to page 4). ACTION - Perform the SERVICE PROCEDURE starting on page 3 and reprogram the Navigation system with USB memory stick shown below.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin does NOT apply to Titan equipped with Cummins V8 Diesel engine. This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. This bulletin has been amended. APPLIED VEHICLES was updated and a DTC listed in the SERVICE INFORMATION was corrected. No other changes have been made. Discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2017-2018 TITAN/TITAN XD; RUNNING BOARD PROTECTIVE FILM RESIDUE SERVICE INFORMATION To help protect the appearance of running boards during shipping, a plastic protective film (white or blue) is installed on the running board chrome strips at the factory. This protective film and its adhesive residue (even if the residue is not visible) must be removed at the dealer: - During the PDI cleaning of the vehicle, or - Immediately after installing running boards. Refer to General Cleaning Information on the next page. Failure to clean adhesive residue leads to dirt collection on the residue, and possible running board chrome strip scratching when customers clean their running boards. Dirt collected in adhesive residue may lead to misdiagnosis that a running board chrome strip is damaged; when in fact it is only dirt and residue that needs proper cleaning.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 TITAN XD; STAGE 1 AND STAGE 2 FUEL FILTER REPLACEMENT SERVICE INFORMATION When replacing the Stage 1 or Stage 2 fuel filters, it is important not to damage the new fuel filters, inner seals, or O-rings. Refer to the Service Procedure section of this bulletin or the Electronic Service Manual (ESM) ENGINE> FUEL SYSTEM> CUMMINS 5.0L> REMOVAL AND INSTALLATION to ensure the filters are being replaced correctly. P008A LOW FUEL PRESSURE CONTROL SYSTEM and/or a no start condition may occur if the procedure is not followed properly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; MICROPHONE DOES NOT WORK This bulletin applies only to vehicles equipped with Telematics. IF YOU CONFIRM The microphone of an applied vehicle does not work. - The person receiving your call through Bluetooth® cannot hear you. And Voice Recognition does not respond to any commands. NOTE: DTCs U1A01 and/or U1A02 may be found stored. ACTION 1. Confirm TCU reprogramming will resolve the issue. - Refer to ?Issue Confirmation? on page 2. 2. If confirmed, reprogram the TCU.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. SERVICE INFORMATION Diagnostic information in the Electronic Service Manuals (ESM) for the following DTCs may be missing or incorrect: -B2EF0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD) -B130C ? TCU (Telematics Control Unit) PAIRING ERROR If one of these DTCs is stored, follow the steps listed below along with the Electronic Service Manual (ESM) to compete the required repairs. DTC B2FE0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD): 1. Start the engine and let it idle for 30 minutes (to allow charging of the TCU internal battery). -2018 LEAF only: Put the vehicle in Ready to Drive mode (depress the brake pedal and depress the power [?ignition?] switch) for 30 minutes. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. DTC B130C: 1. Collect all keys, and then re-register them to the vehicle. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. NOTE: The related Electronic Service Manuals (ESM) will be updated at a later date. CLAIMS INFORMATION Refer to the current Nissan Warranty Flat Rate Manual and submit a claim for the repairs performed.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 TITAN XD; VEHICLE WILL NOT MOVE AND/OR A/T OIL TEMP LIGHT FLASHING This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM The customer reported the following: While driving in conditions where wheel slip can occur (such as dirt, sand, mud, snow/ice, etc.), or while driving/sitting in traffic at slow speeds or idle: -The red A/T Oil Temp lamp began flashing, And/or -Vehicle would not move (the engine felt like it had no power), And -Vehicle operation returned to normal when the engine/transmission was allowed to cool. ACTION 1. Compare the vehicle?s current TCM part number to the part number listed in Table A on page 7. 2. If the current TCM part number matches a part number listed in Table A, follow the instructions in Table A.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016 - 2018 TITAN AND TITAN XD; CLIMATE CONTROLLED HEATED AND COOLED SEATS POOR OR NO OPERATION This bulletin applies only to vehicles equipped with climate controlled seats. This bulletin has been amended. The APPLIED VEHICLES section and pages 17 and 18 have changed. No other changes have been made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 TITAN XD; EXHAUST SMELL INSIDE VEHICLE WHEN HVAC IS ON FRESH AIR This bulletin applies only to vehicles equipped with a Cummins Diesel engine. This bulletin has been amended to update Applied Vehicles, remove the installation of a micro filter and to add a reprogramming procedure. No other changes have been made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 TITAN AND TITAN XD; DOOR WILL NOT OPEN OR DOOR WILL NOT LATCH This bulletin has been amended. The APPLIED VEHICLES have been updated and the SERVICE PROCEDURE now includes the addition of foam to the outside handle bracket. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with a TCU (Telematics Communication Unit). This bulletin has been amended. A correction was made to the Service Procedure on page 23. No other changes were made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin applies to vehicles equipped with Intelligent Key only. SERVICE INFORMATION When replacing or adding an Intelligent Key, it is very important to make sure the correct Intelligent Key is selected from the parts department. - A running change was made that will help identify the correct Intelligent Key. - Beginning in late 2017 and early 2018 the last five digits of the Intelligent Key part number is marked on the Intelligent Key under the mechanical key. - See page 2 for location images of this part number addition. NOTE: - A correct Intelligent Key may or may not have the last five digits of the part number as shown on page 2. - The above running change was applied as a ?help? to identify the correct Intelligent Key for a given vehicle, but the actual part number listed in the parts catalog did not change. - Make sure to use the electronic parts catalog (FAST) or equivalent to confirm the correct Intelligent Key for a given vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles that are equipped with a wireless communication device called a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.