Original record summaries, dates and identifiers for this model-year. Records 101–115 of 115, ordered newest first. Dated records on this page: Jan 30, 2020–Aug 31, 2020.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Aug 31, 2020Service Bulletin/Repair Instructions
NTB20-061
NHTSA communication ID: 10179617
NHTSA source summary · Original PDF not reviewed by Recallfolio
TRAFFIC SIGN RECOGNITION OR LANE DEPARTURE WARNING MALFUNCTION DISPLAYED AND MIL ON WITH DTC C2503-54 AND/OR C1F6B-54 STORED IF YOU CONFIRM The customer states that one of the following warnings is displayed on the vehicle information display along with the AEB Warning Light: ï· Traffic Sign Recognition Malfunction Displayed ï· Lane Departure Warning Malfunction Displayed And ï· The MIL is ON with DTC C2503-54 (CAMERA AIMING INCMP) and/or C1F6B-54 (CAMERA UNIT MALF) stored. NOTE: If DTC C2500-49 and/or C1F6B-49 is stored, this TSB does not apply. ACTION ï· If the vehicle was built on or before 1/31/2020, remove material from the lane camera and then reprogram the lane camera control unit. ï· If the vehicle was built after 1/31/2020 but before 5/29/2020, skip to step 6 and reprogram only the lane camera control unit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020 SENTRA; A/T SHIFT LOCK AND REMOTE START INOPERATIVE WITH NEW BCM SERVICE PART SERVICE INFORMATION After installing a new BCM service part, if the Intelligent Key UNLOCK button is pressed before performing the configuration with CONSULT-III plus, certain BCM configuration parameters will be permanently locked in the default setting; one of these parameters is Remote Engine Start (RES). ï· The default setting for Remote Engine Start is WITHOUT. ï· The RES function WILL BE permanently disabled if the UNLOCK button is pressed BEFORE the BCM service part is configured. IMPORTANT: To avoid permanently disabling the RES feature after replacing the BCM, the configuration procedure must be performed first so that all of the vehicle features operate correctly. Avoid pressing the UNLOCK button on the Intelligent Key after a BCM replacement. Wait until the configuration process has completed and the default configuration has been overwritten with the correct data before pressing any Intelligent Key buttons. Things to remember when replacing a BCM: ï· It is not necessary to register Intelligent Keys to a new BCM. ï· Never press the UNLOCK button on the Intelligent Key until the configuration settings step has been completed. ï· Complete the configuration of the BCM either manually, or by downloading saved configuration from the previous BCM (stored in CONSULT-III plus).
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fuel Filler Door Bumper Dealer Inventory *****Dealer Announcement***** Nissan is conducting a dealer inventory quality action to remove excessive rubber from the fuel lid bumpers on 4,860 specific 2020 Sentra vehicles identified in Service Comm. The fuel filler door may be difficult to open due to the base fuel lid bumper sticking to the lid. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PM948 . New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ⢠Refer to NPSB 15-460 for additional information Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to remedy vehicles affected by this quality action. . Dealers will receive one (1) trim guide per affected dealership. This special tool will be sent to affected dealers via Fed-Ex on July 22, 2020. ⢠Dealers can contact nnafqasupport@nissan-usa.com to obtain a replacement trim guide, if needed. 3. The service department should submit the applicable warranty claim for the action performed so it can be closed on Service Comm and release the vehicle. ***** Dealer Responsibility ***** It is the dealerâs responsibility to check Service Comm or DBS National Service History â Open Campaign using the appropriate campaign I.D for the remedy status on each affected vehicle currently in new vehicle inventory.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020 SENTRA; REAR DOOR ALERT SERVICE INFORMATION SERVICE INFORMATION This bulletin contains supplemental information related to the rear door alert system on 2020 Sentra models. Although the Electronic Service Manual (ESM) should be the primary source of information for inspection, diagnosis, and repair, the supplemental information in this bulletin will assist in these areas. The information in this bulletin includes: ï· Rear door alert description ï· How to turn the rear door alert system on and off ï· How to turn the horn alert function on and off ï· Vehicle information display messages ï· Rear door alert operation NOTE: Do NOT replace the BCM for a rear door alert concern unless all information in this bulletin has been reviewed and the concern has been verified to be abnormal.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · STRUCTURE:BODY:DOOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fuel Feed Tube Clip Dealer Inventory *****Dealer Announcement***** Nissan is conducting a dealer inventory quality action to inspect the fuel feed tube clip and, if necessary, secure it to the fuel line on 9,667 specific 2020 Sentra vehicles identified in Service Comm. Due to a production issue, a small number of fuel line clips may not have been properly set on the high-pressure fuel line and may need to be secured as a result. If the fuel feed tube clip is missing, or damaged, the fuel line will need to be replaced. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PM957 ï· New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ Refer to NPSB 15-460 for additional information ï· Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, loan, sell or trade the specific vehicles in Dealer Inventory subject to this Quality Action. 3. Dealers must use the attached procedure to inspect and, if necessary, secure the fuel tube clip prior to retail delivery of the vehicle. ï· If the fuel feed tube clip is damaged or missing, dealers should replace the fuel line as per the instructions in the Electronic Service Manual (ESM). 4. The service department should submit the applicable warranty claim for the action performed so it can be closed on Service Comm and release the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020 SENTRA; REMOTE ENGINE START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020 SENTRA; DURING PDI DTC B2070-68 FOR KEY REGISTRATION WILL NOT ERASE SERVICE INFORMATION While performing a PDI, if DTC B2070-68 is stored in the Hands-Free control module (Intelligent Key control unit) and will not erase using CONSULT-III plus, no action is necessary. B2070-68 will not affect the vehicle operation and will go to PAST after a number of ignition cycles. NOTE: Do not replace the Intelligent Keys or control units for B2070-68.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020 SENTRA; REMOTE ENGINE START STOPS RESPONDING AND DTC P161F STORED SERVICE INFORMATION The remote engine start (RES) may stop responding and DTC P161F will store in the ECM if RES is performed more than once in quick succession. EXAMPLE: 1. The RES is activated, 2. The ignition is turned OFF; either by RES timer or directly by the start button or key, 3. Within 10 seconds of performing steps 1 and 2, the ignition is turned ON with the RES, start button or key. - When using the RES feature, at least 10 seconds, or more, must elapse between ignition cycles. - If DTC P161F is stored, erase the DTC and Do Not replace the ECM. NOTE: If a customer states the RES stopped responding on a third consecutive activation attempt, please inform them the vehicle allows the RES to be performed only twice consecutively, and must be driven in excess of 5 mph before a third attempt can be performed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Wheel Replacement Dealer Inventory *****Detailed Information***** Nissan is conducting a dealer inventory quality action on 11 MY2020 Sentra (B18) vehicles identified in Service Comm to ensure the correct wheels with center caps and tire pressure sensors have been installed. Steel wheels may have incorrectly been installed on the subject vehicles during manufacturing. Dealers will inspect all four (4) wheels and, if necessary, replace them with the correct aluminum wheels and install center caps and tire pressure sensors. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles currently in new dealer inventory are affected by this quality action using Service Comm or DBS National Service History â Open Campaign I.D. PM946 ï· - New vehicles in dealer inventory can also be identified using DBS (Sales->Vehicle Inventory, and filter by Open Campaign). ï§ - Refer to NPSB 15-460 for additional information ï· - Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this Quality Action. 3. Use the attached procedure to inspect and, if necessary, remedy any vehicles affected by this quality action. 4. Once vehicles have been inspected and, if necessary, remedied dealers may submit the applicable warranty claim for the action performed and the vehicle can be released for sale. ***** Dealer Responsibility ***** It is the dealerâs responsibility to check Service Comm or DBS National Service History â Open Campaign using the appropriate campaign I.D for the inspection status on each affected vehicle currently in new vehicle inventory.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission Control Module (TCM) Reprogram Dealer Inventory *****Dealer Announcement***** Nissan is conducting a dealer inventory quality action and requiring dealers to update the Transmission Control Module (TCM) software on 96 specific 2020 Sentra vehicles identified in Service Comm. The subject vehicles do not have the latest level of software installed. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PM942 ï· - New vehicles in dealer inventory can also be identified using DBS (Sales->Vehicle Inventory, and filter by Open Campaign). ï§ - Refer to NPSB 15-460 for additional information ï· - Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, loan, sell or trade the specific vehicles in Dealer Inventory subject to this Quality Action. 3. Dealers must use the attached procedure to install the updated software prior to retail delivery of the vehicle. 4. The service department should submit the applicable warranty claim for the action performed so it can be closed on Service Comm and release the vehicle. ***** Dealer Responsibility ***** It is the dealerâs responsibility to check Service Comm or DBS National Service History â Open Campaign using the appropriate campaign I.D for the inspection status on each affected vehicle currently in new vehicle inventory.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Steering Gear Housing Inspection Dealer Inventory *****Detailed Information***** Nissan is conducting a quality action on 346 MY2020 Sentra (B18) vehicles identified in Service Comm to inspect for a potential crack on the left side of the steering gear housing and, if necessary, replace the steering gear and linkage assembly. Affected vehicles are subject to stop sale for temporary Quality Assurance (QA) Hold under PC732 and are either currently in dealer inventory or assigned and in transit to the dealer. Nissan is transitioning affected vehicles into this Quality Action campaign ID (PM936). *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED INSPECTION INSTRUCTIONS: 1. Verify if vehicles currently in new dealer inventory are affected by this quality action using Service Comm or DBS National Service History â Open Campaign I.D. PM936 ï· - New vehicles in dealer inventory can also be identified using DBS (Sales->Vehicle Inventory, and filter by Open Campaign). ï§ - Refer to NPSB 15-460 for additional information ï· - Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, loan, sell or trade the specific vehicles in Dealer Inventory subject to this Quality Action.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020 SENTRA; REMOTE ENGINE START SERVICE INFORMATION To use the Remote Engine Start (RES), the following conditions must be met: ï· - The ignition is OFF. ï· - The RES feature is ON in the vehicle settings (access through the vehicle information display). ï· - The shift selector is in the âPâ (park) position. ï· - The hood, doors and trunk lid are closed. ï· - The hazard warning lights are OFF. ï· - The Intelligent Key is within 197 feet (60 m) of the vehicle, and there are no obstructions between the Intelligent Key and the vehicle. ï· - The vehicle is already locked (this must be done using the Intelligent Key or the request switch on the exterior door handle). If the conditions above are met, perform the following to use RES: 1. Point the Intelligent Key at the vehicle. 2. Press the lock button. IMPORTANT: The doors must already be locked prior to starting the RES sequence. Refer to the last bullet point in the conditions list above. 3. Within two (2) seconds of pressing the lock button, press and hold the RES button until the turn signal lights flash and the parking lights turn ON. HINT: When RES is performed, the engine should start, the parking lights should remain ON and the doors should remain locked while the engine is running. If this does not occur, use the Supplemental Diagnosis Table on the next page, in addition to the ESM. ï - Additional information about RES can be found in the ownerâs manual in the Pre-driving checks and adjustments section.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Inside Rearview Mirror Dealer Inventory *****Detailed Information***** Nissan is conducting a quality action on 336 MY2020 Sentra (B18) vehicles identified in Service Comm to inspect the adhesion of the inside rearview mirror attachment and, if necessary, replace the windshield if the mirror detaches. Affected vehicles are subject to stop sale for temporary Quality Assurance (QA) Hold under PC732 and are either currently in dealer inventory or assigned and in transit to the dealer. Nissan is transitioning affected vehicles into this Quality Action campaign ID (PM937). The Quality Hold under PC732 remains in effect for 346 MY2020 Sentra vehicles for a potential crack on the left side of the steering gear housing. Refer to PC732 for additional details. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles currently in new dealer inventory are affected by this quality action using Service Comm or DBS National Service History â Open Campaign I.D. PM937 ï· - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ - Refer to NPSB 15-460 for additional information ï· - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to inspect and, if necessary, remedy any vehicles affected by this quality action: ï· - If the mirror and mounting plate does not detach from the windshield, no repair is needed. - If the inspection result is âNGâ (inside rearview mirror and mounting plate detaches): ï§ - Replace the windshield and aim the front camera unit using the procedure outlined in the Electronic Service Manual (ESM). ï· - Once vehicles have been inspected and, if necessary, remedied dealers may submit the applicable warranty claim for the action performed and the vehicle
NHTSA source summary · Original PDF not reviewed by Recallfolio
MY20 Sentra Quality Hold ***** Detailed Information ***** Nissan is committed to a high level of customer service and satisfaction. This commitment requires Nissan to periodically place certain vehicles on temporary Quality Assurance (QA) Hold to assure that these vehicles, as delivered to our customers, meet our exacting standards and our customersâ expectations. Effective immediately, Nissan is placing a temporary Quality Assurance (QA) Hold on six hundred eighty-two (682) specific MY2020 Sentra vehicles in dealer inventory. There may be a potential crack on the left side of the steering gear housing and/or the rearview mirror may not be mounted to Nissan specifications. Nissan engineering is studying these concerns and will provide the appropriate field actions as quickly as possible. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this quality hold using Service Comm or DBS National Service History â Open Campaigns I.D. PC732 ï· - New vehicles in dealer inventory can be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ - Refer to NPSB 15-460 for additional information ï· - Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this Quality Hold. 3. Nissan will provide an updated status, to include next steps, no later than the week ending February 14, 2020.