Original record summaries, dates and identifiers for this model-year. Records 1–100 of 115, ordered newest first. Dated records on this page: Oct 14, 2020–Apr 13, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 13, 2026Service Bulletin/Repair Instructions
NTB09-131C
NHTSA communication ID: 11031705
NHTSA source summary · Original PDF not reviewed by Recallfolio
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NHTSA source summary · Original PDF not reviewed by Recallfolio
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: When contamination or foreign material adhere to the lane camera viewing window on the windshield. When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: Refer to the following pages. Use the search keyword “blinking” in the ESM.
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If one of the APPLIED VEHICLES has DTC P2100 for “ETC MOT PWR-B1” or P2101 for “ETC FNCTN/CIRC-B1” stored in the Engine Control Module (ECM) with a customer complaint of loss of power, Perform the revised Electronic Service Manual (ESM) procedure noted on page 2 for "PERFORM DTC CONFIRMATION PROCEDURE." HINT: This revised procedure will be added to the ESM in a future update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)
NHTSA source summary · Original PDF not reviewed by Recallfolio
ENGINE SUPPORT TOOLS APPLIED VEHICLES: 2020-2024 Sentra (B18) SERVICE INFORMATION A new Engine Support Bracket is now available to allow the CVT to be removed from the APPLIED VEHICLES without having to remove the engine. The procedure in this bulletin is different from the procedure currently in the ESM, which will be updated with this information at a later date. Please refer to the SERVICE PROCEDURE in this bulletin for information on how to use these new tools.
NHTSA source summary · Original PDF not reviewed by Recallfolio
REVISION 4 Please discard earlier versions of this bulletin. The announcement from July 2, 2024 has been revised to include the following: • The restriction on parts for this campaign will be removed and dealers will be able to order parts via normal process beginning August 9, 2024 Parts on order in DBS will be fulfilled
NHTSA source summary · Original PDF not reviewed by Recallfolio
FALSE ACTIVATION OF AEB OR FCW APPLIED VEHICLES: 2021-2022 Altima (L34) 2022-2023 Frontier (D41) 2020-2022 Sentra (B18) APPLIED DATES: Altima: All Frontier: All Sentra: Built on or before March 10, 2022 APPLIED SYSTEMS: Automatic Emergency Braking/Forward Collision Warning IF YOU CONFIRM The customer states they have experienced false activation and/or unexpected braking of the Automatic Emergency Braking (AEB) or Forward Collision Warning (FCW) system, AND There are no related DTCs stored. ACTION 1. Confirm the current ICC/ADAS 2 part number. 2. Reprogram the ICC/ADAS 2, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
REVISION 3 Please discard earlier versions of this bulletin. The announcement from June 18, 2024 has been revised to include the following: • Parts for this campaign will continue to remain on restriction until further notice. • Continue to order parts via DBS and orders will be filled as quickly as parts are received. • The parts availability condition will be closely monitored.
NHTSA source summary · Original PDF not reviewed by Recallfolio
VOLUNTARY SAFETY RECALL CAMPAIGN 2020-2022 SENTRA; INNER TIE ROD INTRODUCTION Nissan is conducting this voluntary safety recall campaign on certain specific model year 2020-2022 Sentra vehicles to replace both inner tie rods. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number R23B3 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealer’s responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary safety recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer’s inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
VOLUNTARY SAFETY RECALL CAMPAIGN 2020-2022 SENTRA; INNER TIE ROD This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INTELLIGENT KEY UNIT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A/T SHIFT LOCK AND REMOTE ENGINE START INOPERATIVE WITH NEW BCM SERVICE PART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
REAR DOOR ALERT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FALSE ACTIVATION OF AEB OR FCW This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CVT SUB-ASSEMBLY SERVICE PARTS ARE NOW AVAILABLE SERVICE INFORMATION The CVT Belt & Pulley (sub-assembly) Kit is now available to order. The sub-assembly kit part numbers and other parts needed, if a repair is indicated, are listed in PARTS INFORMATION. ï· This bulletin does not include diagnostic or service procedure information. ï· Refer to the ESM for necessary diagnostic information before performing a CVT repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT · EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT · EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NHTSA source summary · Original PDF not reviewed by Recallfolio
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CVT SHIFT SELECTOR LEVER KNOB REMOVAL AND INSTALLATION SERVICE INFORMATION If the CVT Shift Selector Lever Knob needs to be removed or installed for any reason, refer to the SERVICE PROCEDURE in this bulletin, beginning on page 2.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been superseded by: NTB23-018 SOFTWARE UPDATE FOR INFOTAINMENT ISSUES Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
COMBINATION METER MODULES OR ABS CONTROL UNITS CANNOT BE SWAPPED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WINDSHIELD WIPER BLADE PERFORMANCE/DIAGNOSIS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LOSS OF POWER, ENGINE NOISE, AND/OR BATTERY LIGHT ON IF YOU CONFIRM The customer describes one, or more, of the following: ï· Loss of power ï· Loud noise from the front of vehicle/engine area while running ï· The battery light is ON AND ï· It is confirmed that the noise is coming from the generator (alternator) ACTION Replace the Drive Belt Auto Tensioner, the Alternator, and the associated Drive Belt listed in the PARTS INFORMATION on the last page.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DTC P161D STORED IN BCM IF YOU CONFIRM DTC P161D (Immobilizer) is stored in the BCM,. ï· If a DTC other than P161D is present, diagnose and resolve first before applying this bulletin. AND The current ECU PART NUMBER in the BCM is either 284B3-3613R or 284B3-6580R. ACTION Reprogram the BCM with the SERVICE PROCEDURE in this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL ON WITH DTC P0401 AND/OR P0404 STORED IN THE ECM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LANE CAMERA OVER TEMPERATURE DTC STORED SERVICE INFORMATION The Lane Camera can become overheated if the interior room temperature or temperature around the camera becomes excessively high, and does not initially indicate a sustained fault. If overheated, the Lane Camera should be cooled to outside ambient temperature, any stored DTCs erased, and then allowed to resume operation. Refer to the ESM for any DTCs that will not erase. This condition may cause the following system functions to be suspended: ï· Vehicle-to-vehicle distance control mode (ICC - Intelligent Cruise Control) ï· Conventional (fixed speed) cruise control mode ï· Steering wheel assistance function ï· AEB (Automatic Emergency Braking) ï· LDW (Lane Departure Warning) ï· I-LI (Intelligent Lane Intervention) ï· Blind Spot Intervention ï· TSR (Traffic Sign Recognition) AND Can store one or more of the following DTCs as PAST or CURRENT: ï· C2501-4B (Front camera unit) ï· C1F05-4B (Front camera unit) ï· C1F6B-4B (Front camera unit) For customer information, see Talk Tip "Customer" statement on page 3.
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE · LANE DEPARTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL ON WITH DTC P0401 AND/OR P0404 STORED IN THE ECM IF YOU CONFIRM The MIL is ON and DTC P0401 (EGR A FLOW INSUFFICIENT) and/or P0404 (EGR A CONTROL) is stored in the ECM. AND There are no drivability concerns. ACTION 1. Confirm the current ECM part number. 2. Reprogram the ECM, if applicable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HORN INOPERATIVE IF YOU CONFIRM The horn on an APPLIED VEHICLE is inoperative. ACTION Inspect the horn pad for a pinched ground wire. If a pinched ground wire is found, replace the high and low horns.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:HORN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
Source components: ELECTRICAL SYSTEM:INSTRUMENT PANEL:FUEL GAUGE:FUEL LEVEL FLOAT/SENSOR/SENDING UNIT · ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE · FUEL SYSTEM, DIESEL · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
COMBINATION METER MODULES OR ABS CONTROL UNITS CANNOT BE SWAPPED This bulletin has been amended. See AMENDMENT HISTORY, below. Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES, AIR:ANTILOCK:CONTROL UNIT/MODULE · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:CONTROL UNIT/MODULE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INTELLIGENT KEY UNIT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
REAR DOOR ALERT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FALSE ACTIVATION OF AEB OR FCW IF YOU CONFIRM The customer states they have experienced false activation and/or unexpected braking of the Automatic Emergency Braking (AEB) or Forward Collision Warning (FCW) system, AND There are no related DTCs stored. ACTION 1. Confirm the current ICC/ADAS 2 part number. 2. Reprogram the ICC/ADAS 2, if applicable.
Source components: FORWARD COLLISION AVOIDANCE · SERVICE BRAKES, ELECTRIC:SOFTWARE/PROGRAMMING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR SERVICE INFORMATION If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the âPASTâ column: ï· Erase the DTC. ï· DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue, always confirm that the latest software is installed in the AV control unit before starting the diagnosis. The software update in the following service procedure is to address the items below: ï· Stability improvements and âbugâ fixes. Refer to steps 1 - 4 starting on page 3 to confirm that this bulletin applies.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INTELLIGENT AUTO HEADLIGHTS DO NOT COME ON WHEN WIPERS ARE ACTIVE IF YOU CONFIRM While in AUTO headlight mode, the Intelligent Headlights do not come ON after four (4) complete sweeps of the windshield wipers. ï· The four (4) complete windshield wiper sweeps must occur within a one (1) minute time period. NOTE: Windshield wipers are set to any ON position. ACTION Reconfigure the BCM.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BCM REPROGRAM TO DISABLE FOG LAMP OPERATION DURING HIGH BEAM OPERATION IF YOU CONFIRM The vehicle is in Pennsylvania and the fog lamps remain ON during high beam operation. ACTION Reprogram the BCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL ON WITH DTC P062F AND/OR P0603 STORED IF YOU CONFIRM The MIL is ON and DTC P062F (EEPROM) and/or P0603 (ECM BACK UP/CIRCUIT) is stored, And The customer stated the vehicle was recently started after sitting for an extended period of time (i.e., the battery voltage was low while attempting to start the engine). ACTION 1. Test the vehicleâs 12 volt battery using the Midtronics DSS-5000. Recharge or replace the battery if necessary. 2. Erase all DTCs.
NHTSA source summary · Original PDF not reviewed by Recallfolio
VOLUNTARY SERVICE CAMPAIGN BCM REPROGRAM TO DISABLE FOG LAMP OPERATION DURING HIGH BEAM OPERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Inner Socket (Tie Rod) Inspection Dealer Inventory Dealer Announcement: Nissan is conducting a dealer inventory quality action to inspect the inner socket (Tie Rod) and, if necessary, replace the right and/or left Tie Rods on 4,551 specific 2020 Sentra vehicles identified in Service Comm. The subject vehicles may have inner sockets that were damaged in either the manufacturing or the delivery process. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. What Dealers Should Do: PLEASE FOLLOW THE ATTACHED INSPECTION INSTRUCTIONS: 1.Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PM973 â¢New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§Refer to NPSB 15-460 for additional information â¢Please continue to check newly arriving inventory for campaign applicability. 2.Use the attached procedure to inspect vehicles affected by this quality action. â¢If the inspection results indicate that the tie rods are not bent, âNO=Goodâ, no part replacement is necessary. ï§File a claim for the inspection, and release the vehicle for sale. â¢If the inspection results indicate that the tie rods are bent, âYES=NGâ, do not submit a warranty claim, provide the requested information in an email to nnafqasupport@nissan-usa.com and HOLD the vehicle until further notice. ï§Nissan FQA will review the E-mail submission and provide the dealer with repair and warranty claim instructions within two (2) business days of receipt. Dealer Responsibility: It is the dealerâs responsibility to check Service Comm or DBS National Service History â Open Campaign using the appropriate campaign I.D for the inspection status on each affected vehicle currently in new vehicle inventory.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL SERVICE INFORMATION If an Applied Vehicle needs to have a front axle nut removed, for any reason, the staking of the nut into the axle keyway must first be removed. The essential tool (part number # J-52982, Figure 1) required to remove the nut staking, is called out as a âCape Chiselâ in the Electronic Service Manual (ESM), and must be used to prevent thread damage to the axle (see Figure 2 on page 2). ï· The Cape Chisel arrived at dealers in December of 2020. ï· Damaged threads, due to improper removal of the stake placed in the nut, will not be covered by warranty. For information on using the Cape Chisel, refer to the Electronic Service Manual (ESM): Section TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT > LH/RH.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TRAFFIC SIGN RECOGNITION OR LANE DEPARTURE WARNING MALFUNCTION DISPLAYED AND MIL ON WITH DTC C2503-54 AND/OR C1F6B-54 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · FORWARD COLLISION AVOIDANCE · LANE DEPARTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020 SENTRA; DURING PDI DTC B2070-68 FOR KEY REGISTRATION WILL NOT ERASE This bulletin has been amended. See AMENDMENT HISTORY, below. Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2021 ROGUE AND 2020 SENTRA; INTELLIGENT KEY UNIT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY, below. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
KICKS, LEAF, SENTRA AND VERSA; FRONT DOOR WILL NOT OPEN This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fog Lamp Reprogram Voluntary Service Campaign Campaign Summary: Nissan is conducting a Voluntary Service Campaign to reprogram the Body Control Module (BCM) on certain 2020 model year Nissan Sentra (B18) SR grade vehicles, registered or being sold for registration within the state of Pennsylvania, with countermeasure software to prevent the vehicleâs fog lamps from being activated at the same time high beams are used. The vehicleâs current software allows fog lamps to operate while the high beams are engaged, which may not be permitted under current Pennsylvania Vehicle Inspection standards. The driver may use the manual switches to operate either the fog lamps or high beams, but without the software update, the vehicle may not pass Pennsylvaniaâs Vehicle Safety Inspection. What Dealers Should Do: 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History â Open Campaigns I.D. P0A34. 2. Dealers are requested to inspect and, if necessary, repair any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction. â¢New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§Refer to NPSB15-460 for additional information 3. Dealers should use NTB20-096 to correct any vehicles subject to this campaign. 4. Once repaired, dealers should submit the claim, using the claims coding provided, nd release the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
VOLUNTARY SERVICE CAMPAIGN BCM REPROGRAM TO DISABLE FOG LAMP OPERATION DURING HIGH BEAM OPERATION INTRODUCTION Nissan is conducting this voluntary service campaign, on certain specific model year 2020 Sentra SR models, to reprogram the BCM in order to disable fog lamp operation when the high beams are in use. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number P0A34 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INTELLIGENT KEY UNIT DTC P161D STORED IN THE ECM SERVICE INFORMATION DTC P161D (IMMOBILIZER) will not cause: ï· The MIL to turn ON. ï· The Remote Engine Start to become inoperative. ï· The âNo Key Detectedâ message to appear. ï· An impact to any of the vehicleâs functions or performance. If other DTCs are stored with P161D, perform the diagnosis and repair procedures, outlined in the ESM, for the other DTCs first. ï· After the other DTCs have been resolved and P161D does not clear, proceed with the diagnosis and repair, outlined in the ESM, for DTC P161D.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM) · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
REAR DOOR ALERT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2021 ROGUE AND 2020 SENTRA; BCM SERVICE INFORMATION SERVICE INFORMATION ï· When replacing the BCM, ALWAYS replace it with a new one. ï· Module configuration MUST BE performed before pairing the BCM and intelligent key unit. Once the BCM and intelligent key unit have been paired, portions of the configuration are locked and can no longer be changed. ï· When replacing the BCM, it is critical to follow the work procedure as detailed in the ESM. ï For Rogue, go to ELECTRICAL & POWER CONTROL > BODY CONTROL SYSTEM > BASIC INSPECTION > ADDITIONAL SERVICE WHEN REPLACING BCM. ï For Sentra, go to ELECTRICAL & POWER CONTROL > BODY CONTROL SYSTEM > BASIC INSPECTION > INSPECTION & ADJUSTMENT > ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
2021 ROGUE AND 2020 SENTRA; INTELLIGENT KEY UNIT SERVICE INFORMATION SERVICE INFORMATION ï· When replacing the intelligent key unit (hands free module), ALWAYS replace it with a new one. ï· Module configuration MUST BE performed before NATS initialization (key registration). Once NATS initialization has been performed, portions of the configuration are locked and can no longer be changed. ï· When replacing the intelligent key unit, it is critical to follow the work procedure as detailed in the ESM. ï For Rogue, go to BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY >DOOR & LOCK > BASIC INSPECTION > ADDITIONAL SERVICE WHEN REPLACING INTELLIGENT KEY UNIT. ï For Sentra, go to BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY >DOOR & LOCK > BASIC INSPECTION > INTELLIGENT KEY UNIT >ADDITIONAL SERVICE WHEN REPLACING INTELLIGENT KEY UNIT.