The manufacturer’s record · Page 2 of 2
Original record summaries, dates and identifiers for this model-year. Records 101–127 of 127, ordered newest first. Dated records on this page: Aug 27, 2012–Apr 9, 2014.
Back to 2013 Nissan ROGUE problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10055490
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: THE MAIN HARNESS TO BODY HARNESS CONNECTORS IS EXPERIENCING ELECTRICAL CORROSION ISSUES. 2008-2014 ROGUE. *PE
Source components: ELECTRICAL SYSTEM.
Source record 10055490 at NHTSANHTSA communication ID: 10192335
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM A rattle coming from the exhaust center tube heat shield, and a heat shield spot weld is detached, ACTION Install a band clamp around the heat shield and over the detached spot weld. See this bulletin for further detail.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10192335 at NHTSANHTSA communication ID: 10054095
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: IGNITION MUST CYCLE TWO TIMES TO COMPLETE CONFIGURATION FOR NAVIGATION EQUIPPED VEHICLES AND IF CONFIGURATION NOT COMPLETED SOME SYMPTOMS MAY OCCUR (NO BACK UP CAMERA, NO VOLUME RESPONSE, EQUALIZER ADJUSTED SO BASS CONTROL IS AT MAXIMUM, NO STEERING WHEEL SWITCH RESPONSE). MODEL 2014 ALTIMA, ROGUE, FRONTIER, SENTRA, XTERRA. *PE UPDATED 02/26/2014 *JS UPDATED 4/22/14. *PE
Source components: ELECTRICAL SYSTEM.
Source record 10054095 at NHTSANHTSA communication ID: 10192305
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
Source components: AIR BAGS · EQUIPMENT.
Source record 10192305 at NHTSANHTSA communication ID: 10192293
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
Source components: ENGINE · ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM).
Source record 10192293 at NHTSANHTSA communication ID: 10053958
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: CERTAIN VEHICLES WOULD DISPLAY, IN THE INSTRUMENT CLUSTER, A WARNING LIGHT ILLUMINATION OF A LOOSE FUEL CAP WARNING. MODEL YEARS 2012-2014. NO MODELS LISTED. *PE
Source components: FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP.
Source record 10053958 at NHTSANHTSA communication ID: 10054527
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: INFORMATION REGARDING TIRE PRESSURE MONITOR SYSTEM (TPMS) AND LOW TIRE PRESSURE WARNING SYSTEM (LTPWS) FOR SENSOR LEAKS, AIR PRESSURE CHANGES WITH ALTITUDE AND AMBIENT TEMPERATURES, AFTERMARKET WHEELS, RADIO FREQUENCY INTERFERENCE CAUSING NO DATA CONDITION AND INFLATING/DEFLATING TIRES WITH TPMS/LTPWS SENSORS. MODEL ALL. NO MODELS YEARS. *PE
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
Source record 10054527 at NHTSANHTSA communication ID: 10192234
NHTSA source summary · Original PDF not reviewed by Recallfolio
Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10192234 at NHTSANHTSA communication ID: 10192233
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
Source components: EQUIPMENT · WHEELS.
Source record 10192233 at NHTSANHTSA communication ID: 10192231
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.
Source components: ELECTRICAL SYSTEM.
Source record 10192231 at NHTSANHTSA communication ID: 10192217
NHTSA source summary · Original PDF not reviewed by Recallfolio
If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.
Source components: SERVICE BRAKES · STEERING · WHEELS.
Source record 10192217 at NHTSANHTSA communication ID: 10192216
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.
Source components: SERVICE BRAKES · STEERING · SUSPENSION · WHEELS.
Source record 10192216 at NHTSANHTSA communication ID: 10192192
NHTSA source summary · Original PDF not reviewed by Recallfolio
As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
Source components: ELECTRICAL SYSTEM.
Source record 10192192 at NHTSANHTSA communication ID: 10192178
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If a customer would like to activate a subscription for any of the following services: - SiriusXM Satellite Radio, NavTraffic, NavWeather, Travel Link Weather OR If a radio is replaced for any reason, and a customer has an active subscription to any of the above services, OR If a customer claims to have an active subscription to any of the above services, AND any portion of the subscribed service is not operating, ... follow the steps in this bulletin to activate/refresh the service.
Source components: SUSPENSION.
Source record 10192178 at NHTSANHTSA communication ID: 10192158
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Improper adjustment or operation of the ASCD brake switch can cause the Automatic Speed Control Device (ASCD) to "not set" and/or DTC P0605 (ECM) to store. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM.
Source record 10192158 at NHTSANHTSA communication ID: 10051768
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: CRUISE CONTROL WILL NOT SET AND DTC P0605 IS STORED. *JS
Source components: VEHICLE SPEED CONTROL:CRUISE CONTROL.
Source record 10051768 at NHTSANHTSA communication ID: 10192155
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The "Lock / Unlock request buttons" that are located on the outside door handles of vehicles with Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled. Please verify the status of this feature before any further diagnostic is performed. Please see this bulletin for further details.
Source components: SEAT BELTS · VEHICLE SPEED CONTROL.
Source record 10192155 at NHTSANHTSA communication ID: 10051767
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: LOCK/UNLOCK REQUEST BUTTON ON OUTSIDE HANDLE DOES NOT RESPOND. *JS
Source components: LATCHES/LOCKS/LINKAGES.
Source record 10051767 at NHTSANHTSA communication ID: 10192145
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
Source components: SUSPENSION.
Source record 10192145 at NHTSANHTSA communication ID: 10192127
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident vehicles. - Customers must not use discs that are warped, scratched, chipped, cracked, have abnormal edges or are otherwise damaged. Damaged or poor condition discs may cause the Player internal mechanism to jam or have optical pick-up errors. NOTE - Do not make a Warranty claim against a Player that will not play damaged or poor condition discs as described in this bulletin. See this bulletin for further detail.
Source components: STRUCTURE.
Source record 10192127 at NHTSANHTSA communication ID: 10192120
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM Oil is leaking from the upper end of the engine oil cooler. ACTION: Reseal the oil cooler with the parts listed in the PARTS INFORMATION on page 2. - For repairs, refer to REPAIR PROCEDURE starting on page 3. NOTE: Do not replace the complete engine oil cooler assembly for this incident, if it should occur. See this bulletin for further detail.
Source components: EQUIPMENT.
Source record 10192120 at NHTSANHTSA communication ID: 10192114
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION A new updated front brake rotor service part is available for the Applied Vehicles in this bulletin. See this bulletin for further detail.
Source components: EQUIPMENT.
Source record 10192114 at NHTSANHTSA communication ID: 10192100
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION To increase tire/wheel assembly balancing accuracy, proper steps should be followed - Make sure to use the correct size wheel centering collet (do not use a cone). - Make sure to use a flange plate and stud set to secure the tire/wheel assembly on the balancer (do not use a cup). - Perform proper wheel mounting and centering checks. See this bulletin for further detail.
Source components: WHEELS.
Source record 10192100 at NHTSANHTSA communication ID: 10192095
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The customer has experienced or is experiencing, while using the hands-free phone, people on the other end of a phone call cannot hear them. The customer's experience may include: Voice is choppy or cuts-out, sounds distant, sounds as if speaking through a tunnel, sounds like it is under water. ACTION 1. Replace the TEL Adaptor Unit. 2. Replace the microphone and the map lamp finisher. - For Juke, replace the microphone and microphone finisher. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM.
Source record 10192095 at NHTSANHTSA communication ID: 10192068
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The R&I (Remove and Install) procedure on an applied vehicle for blower motor service will be amended to include the knee bracket. If a blower motor is to be removed and reinstalled or replaced, add the step shown in this bulletin. - The procedure for blower motor R&I is in the I VENTILATION, HEATER & AIR CONDITIONER>VTL Ventilation System section of all related ESMs. See this bulletin for further detail.
Source components: ENGINE AND ENGINE COOLING.
Source record 10192068 at NHTSANHTSA communication ID: 10046601
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: BULLETIN REGARDING DIAGNOSIS OF ABS/VDC WHEEL SPEED SENSOR. MODEL 2007-2013 NISSAN. *PE
Source components: SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING.
Source record 10046601 at NHTSANHTSA communication ID: 10047059
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: RAIN SENSORS MAY OPERATE, INTERMITTENTLY OR UNEXPECTEDLY, WHEN EXHAUST GAS, MOISTURE, FINGERPRINTS, DIRT, OR INSECTS ARE NEAR OR AROUND RAIN SENSORS. NO MODELS OR MODEL YEARS LISTED. *PE
Source components: VISIBILITY/WIPER.
Source record 10047059 at NHTSA