Original record summaries, dates and identifiers for this model-year. Records 1–100 of 117, ordered newest first. Dated records on this page: Sep 14, 2009–Apr 13, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 13, 2026Service Bulletin/Repair Instructions
NTB09-131C
NHTSA communication ID: 11031705
NHTSA source summary · Original PDF not reviewed by Recallfolio
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NHTSA source summary · Original PDF not reviewed by Recallfolio
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NHTSA source summary · Original PDF not reviewed by Recallfolio
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NHTSA source summary · Original PDF not reviewed by Recallfolio
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
VOLUNTARY SERVICE CAMPAIGN 2008 ALTIMA SEDAN; CVT COOLER HOSE CLAMP Service Campaign ID # PB085 is no longer active. ï· Repair orders opened after this bulletinâs published date are no longer eligible for reimbursement under Campaign ID # PB085. ï· Discard all previous versions of NTB08-077.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Expiration Notification â Drive Belt Tensioner Bolts ***** Campaign Summary***** In 2008, Nissan launched a Voluntary Service Campaign on certain 2008 Altima (L32) vehicles, equipped with 4-cylinder 2.5L engine, to re-torque the engine accessory drive belt tensioner bolts to specification. During manufacturing, the engine accessory drive belt tensioner bolts may not have been torqued to specification. This may affect performance of certain engine accessories on the vehicle, including the air conditioning compressor, alternator and the water pump. Parts specified for this campaign are no longer available through Nissan. This customer service campaign and customer reimbursement for these repairs are no longer available. ***** What Dealers Should Do ***** 1. Service Comm will deactivate PB072 on any unrepaired VINs on March 25, 2021. No further dealer action is required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
VOLUNTARY SERVICE CAMPAIGN 2008 ALTIMA SEDAN DRIVE BELT TENSIONER BOLTS (2.5L ENGINE) Service Campaign ID # PB072 is no longer active. ï· Repair orders opened after this bulletin's published date are no longer eligible for reimbursement under Campaign ID # PB072. ï· Discard all previous versions of NTB08-051.
NHTSA source summary · Original PDF not reviewed by Recallfolio
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
Source components: SERVICE BRAKES, AIR:SUPPLY:CHECK VALVE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING IF YOU CONFIRM The MIL is ON in an APPLIED VEHICLE with DTC P0456 (EVAP VERY SML LEAK) AND - DTC P0456 is not caused by a loose fuel fill cap (refer to NTB13-097). - An EVAP leak has been detected where the vent control valve mounts to the canister. - The vent control valve O-ring seal is determined to be the cause. ACTION 1. DO NOT REPLACE the vent control valve. 2. Replace the vent control valve O-ring seal (O-ring). - Refer to SERVICE PROCEDURE on page 2.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2007-2010 ALTIMA; REDUCED PERFORMANCE DUE TO CVT FLUID TEMPERATURE PROTECTION LOGIC This bulletin has been amended to remove 2011 and 2012 model years. Please discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"ALTIMA, SENTRA, AND ROGUE; CVT FAIL-SAFE CONDITION SERVICE INFORMATION THIS BULLETIN HAS BEEN AMENDED. THE APPLIED VEHICLES SECTION HAS BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN."
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: The vehicle speed is, or was, reduced by the CVT fail-safe (reduced vehicle speed) after continuous operation under the following conditions: * High RPM and/or high speed driving (RPM of 4000+ or speeds of 65 mph (104.6 km/h) for 1.0 - 1.5hrs or more) * Driving in ambient temperature of 96 degrees or higher * Climbing steep or extended hills for 6 miles (9.6 km) or more * Whine or rattle type noise occurring during reduced engine performance (vehicle speed decrease) ACTIONS: Install the SERVICE KIT-COOLER ASSY. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
Source components: BACK OVER PREVENTION · LANE DEPARTURE · SERVICE BRAKES · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
Source components: BACK OVER PREVENTION · EQUIPMENT · SERVICE BRAKES · STEERING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION When diagnosing possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
Source components: AIR BAGS · BACK OVER PREVENTION · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
see NTB13-056 INTRODUCTION Nissan has determined that on some 2007 ? 2008 Altima Sedans and 2008 Altima Coupes equipped with the 2.5 liter four cylinder engines, a rattle noise may occur around the exhaust manifold heat shield during start up or at low engine speeds (approximately 1600 RPM). The symptom does not affect the operation of the engine or the vehicle. To address this issue, Nissan is conducting a Voluntary Service Campaign to replace the lower exhaust manifold heat shield. IDENTIFICATION NUMBER Nissan has assigned identification number PB053 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION When an exhaust manifold and three way catalyst assembly is removed from an applied vehicle for any reason: 1. Remove and discard the exhaust manifold stay and its related parts. 2. The upper and lower exhaust manifold covers (heat shields) may need to be replaced. - Refer to the FLOW CHART on page 3 for detailed vehicle applicability. See this bulletin for further detail.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: INFORMATION PROVIDED REGARDING REMOVAL OF THREE WAY CATALYST AND EXHAUST MANIFOLD SERVICE AND REPLACEMENT, IF NEEDED, OF UPPER/LOWER (HEAT SHIELD) EXHAUST MANIFOLD COVERS. MODEL 20007-10 SEDAN/COUPE, 2007-11 HYBRID. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. VOLUNTARY SERVICE CAMPAIGN--2007-2008 ALTIMA SEDAN AND 2008 ALTIMA COUPE - EXHAUST HEAT SHIELD (2.5L). CSC WAS RECEIVED. *NJ UPDATED 4/8/08. *NJ UPDATED 11/14/14. *PE
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: SRS PRECAUTIONS DURING SERVICE;IMPROPER MAINTENANCE, INCLUDING INCORRECT REMOVAL AND INSTALLATION OF THE SRS, CAN LEAD TO A SERIOUS INJURY OR DEATH CAUSED BY UNINTENTIONAL ACTIVATION OF THE SRS ON ALL NISSAN MODELS WITH THE SRS SYSTEMS. *PE UPDATED 2/21/14. *PE
Source components: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: EXTERIOR LAMP FOGGING. OCCASIONALLY WATER IS NOTICED IN THE EXTERIOR LAMPS. THIS IS GENERALLY NOT DUE TO A DEFECT. ALL CURRENT EXTERIOR LAMP ASSEMBLIES ARE VENTED TO THE ATMOSPHERE (NOT SEALED). THIS IS NECESSARY TO ALLOW FOR EXPANSION AND CONTRACTION OF AIR FROM TEMPERATURE VARIATIONS (WARMER OR COLDER) WITHOUT DAMAGE TO THE LAMP. MOISTURE IN THE AIR SOMETIMES TRAVELS INTO AND OUT OF THE LAMP ASSEMBLY THROUGH THESE VENTS. CERTAIN ENVIRONMENTAL CONDITIONS MAY CAUSE MOISTURE TO CONDENSE. THE FOGGING/CLOUDINESS SHOULD DISAPPEAR OVER TIME WHEN THE LAMP IS IN A DRY ENVIRONMENT. NO MODELS LISTED. *PE UPDATED 5/7/10. *PE UPDATED 12/9/13. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456) on a 2007 through 2011 Nissan vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm the cause of stored DTCs. ASIST: - Appropriate Service Manual diagnostic procedures - Applicable Technical Service Bulletins (TSB). Leak Test: - With CONSULT-III plus - WORK SUPPORT >> EVAP SYSTEM CLOSE. NOTE: Use Essential Tool J-42909 or equivalent to pressurize the EVAP system. - With a "Smoke" leak detection machine. Refer to the machine's Operator's Manual for proper use. Make sure the customer is informed of the proper fuel filler cap installation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: A LOOSE FUEL FILL CAP IS THE CAUSE OF EVAP LEAK DTCS (P0442, P0455, P0456) STORED ON SOME VEHICLES. MODEL YEARS 2007-2011. MODEL NOT LISTED. *PE
Source components: FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: RECALL CAMPAIGN. SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. DUE TO INCORRECTLY DETECTING ENGINE VALVE CLOSURE, SOME VEHICLES ARE EQUIPPED WITH IMPROPERLY CALIBRATED ENGINE CONTROL MODULE (ECM) THAT NEEDS REPROGRAMMING, AND INSPECTED AND IF NECESSARY, REPLACED. MODEL 2008 ALTIMA. *PE UPDATED 10/31/13. *PE
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AFTERMARKET CHROMING OF NISSAN ALLOY WHEELS NOT APPROVED OR AUTHORIZED AND STRONGLY DISCOURAGED. ALL MODELS INCLUDING 2008-2009 MY. *PE UPDATED 1/31/14. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.
Source components: SERVICE BRAKES · STEERING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.
Source components: SERVICE BRAKES · STEERING · SUSPENSION · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If you confirm there is a need to replace the steering wheel switches on an Applied Vehicle for any reason: - Do not replace the driver air bag module. The steering wheel switches are now available as a separate service part. - Refer to the Service Procedure in this bulletin for steering wheel switch removal and installation instructions. See this bulletin for further detail.
Source components: AIR BAGS · ELECTRICAL SYSTEM · SEATS · STEERING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: SERVICE INFORMATION ON THE REMOVAL AND INSTALLATION OF SERVICE PARTS, ON CERTAIN VEHICLES, FOR THE STEERING WHEEL SWITCH, IF NEEDED, WITHOUT REPLACING THE DRIVER AIRBAG MODULE. MODELS 2007-2013 ALTIMA. *PE
Source components: STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The "Lock / Unlock request buttons" that are located on the outside door handles of vehicles with Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled. Please verify the status of this feature before any further diagnostic is performed. Please see this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan is conducting a Voluntary Service Campaign on Model Year 2007-2012 Nissan Altima (L32) Sedan and Coupe vehicles to inspect the brake systems in vehicles with an illuminated brake warning lamp. Nissan dealers will inspect the brake system and confirm that no brake fluid leak is present. If no leak is present, the reservoir will be topped off. If a leak in the brake master cylinder is identified, the brake master cylinder will be replaced. The affected vehicles are equipped with a brake warning lamp that will illuminate to alert the driver when fluid in the brake fluid reservoir is low. Fluid in the reservoir may become low due to normal brake pad wear and not because of any brake system malfunction. While in most instances an illuminated brake warning lamp is due to normal brake pad wear, a small percentage of vehicles affected by this campaign may have a slow brake fluid leak at the brake master cylinder. See this bulletin for further detail. Campaign ID# PC125
NHTSA source summary · Original PDF not reviewed by Recallfolio
BRAKE MASTER CYLINDER. BRAKE SYSTEM WILL BE INSPECTED TO CONFIRM THAT NO BRAKE FLUID LEAK IS PRESENT. RESEVOIR WILL BE TOPPED OFF IF NO LEAK IS PRESENT. IF THERE IS A LEAK IN THE BRAKE MASTER CYLINDER IS IDENTIFIED THE BRAKE MASTER CYLINDER WILL BE REPLACED. NISSAN. *KB
Source components: SERVICE BRAKES, HYDRAULIC · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:MASTER CYLINDER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident vehicles. - Customers must not use discs that are warped, scratched, chipped, cracked, have abnormal edges or are otherwise damaged. Damaged or poor condition discs may cause the Player internal mechanism to jam or have optical pick-up errors. NOTE - Do not make a Warranty claim against a Player that will not play damaged or poor condition discs as described in this bulletin. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM Oil is leaking from the upper end of the engine oil cooler. ACTION: Reseal the oil cooler with the parts listed in the PARTS INFORMATION on page 2. - For repairs, refer to REPAIR PROCEDURE starting on page 3. NOTE: Do not replace the complete engine oil cooler assembly for this incident, if it should occur. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SOME MODEL YEAR VEHICLES MAY BE EXPERIENCING LEAKAGE IN BRAKE MASTER CYLINDER WHICH MAY CAUSE BRAKE WARNING LIGHT TO BE ILLUMINATED. MAY NEED TO REPLACE BRAKE MASTER CYLINDER. *PE UPDATED 5/9/12. *PE UPDATED 4/1/13. *PE
Source components: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:MASTER CYLINDER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: IF CONTINUOUSLY VARIABLE TRANSMISSION (CVT) FLUID TEMPERATURE RISES ABOVE A CERTAIN THRESHOLD, IT WILL GO INTO FLUID PROTECTION LOGIC MODE (FAIL SAFE MODE), AS DESIGNED. *PE
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: ALTIMA, MAXIMA; POWER STEERING HOSE SERVICE PART CHANGE. THE HOSE NOW COMES WITHOUT THE PRESSURE SENSOR. DO NOT DAMAGE PRESSURE SENSOR UPON REMOVAL OR INSTALLATION. IF ONLY THE PRESSURE SENSOR NEEDS TO BE REPLACED, DO NOT REPLACE ANY HOSES. *JS
Source components: STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. BRAKE SYSTEM CHECK TO SEE IF THERE IS FLUID LEAKING OR IF THE BRAKE MASTER CYLINDER IS LEAKING. *KB
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: THERE IS A SURGE WHEN DRIVING WHEN ALL OF THE FOLLOWING ARE PRESENT: SLOW ACCELERATION, BETWEEN 10-45MPH, WITH ENGINE CLUTCH ENGAGED, AND THE RPMS BETWEEN 1200-2000. 2007-2011 ALTIMA. *RM UPDATED ON 08-11-2011. *KB UPDATED 10/3/11. *PE
Source components: ENGINE AND ENGINE COOLING:ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: THE MIL IS ON WITH ONE OR MORE OF THE FOLLOWING DTCS STORED: P0442/P0448/P0455/P0456 AND EVAP VENT CONTROL VALVE IS STUCK OPEN OR WILL NOT SEAL WHEN OPERATED/CLOSED. REPLACE VENT CONTROL VALVE; INSTALL FILTER KIT LISTED IN PARTS INFORMATION; AND CLEAR ANY DTCS STORED IN THE ECM. *PE UPDATED 6/15/11. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: NAVIGATION MAP DATA UPDATE MATRIX. AFFECTING ALL VEHICLES 2003-11 EXCEPT LEAF, EQUIPPED WITH NAVIGATION SYSTEM. CUSTOMER IS MAILED UPDATE DISC(S) OR SD CARD AND INSTALLS DATA; DEALERSHIP IS MAILED UPDATE DISC(S) AND THE DEALERSHIP INSTALLS DATA WHEN VEHICLE IS BROUGHT IN. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: VENT CONTROL VALVE REPLACEMENT. WHEN REPLACING THE EVAP CANISTER VENT CONTROL VALVE FOR REASON: USE THE ONE LISTED ON PAGE 2; FOR VENT CONTROL VALVE REPLACEMENT PROCEDURE, REFER TO THE APPROPRIATE SECTION OF THE ELECTRONIC SERVICE MANUALS (ESM; WHEN INSTALLING THE NEW VALVE, DO NOT ADD ANY LUBE TO ITS O RING; FOR FRONTIER (D40 SERIES) ONLY, INSTALL THE PROTECTOR LISTED IN PARTS INFORMATION. *PE INCLUDES 2005-09 FRONTIER. UPDATED 12/8/10. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: XENON HEAD LAMP SERVICE. A XENON HEADLAMP IS NOT FUNCTIONING BECAUSE OF AN ISSUE INSIDE THE HEADLAMP ASSEMBLY (AN INTERNAL ISSUE). IN MOST CASES, REPLACEMENT OF A BULB OR HID CONTROL UNIT WILL SOLVE THE INCIDENT. THIS INCLUDES ALL MODELS WITH XENON HEAD LAMPS. NO MODELS LISTED. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN: MIL ON W/DTC P0840, P0845, P0744, P1777. REPLACE THE CONTROL VALVE ASSEMBLY WITH PART LISTED; REFERENCE SECTION TM, CONTROL VALVE REMOVAL AND INSPECTION IN APPROPRIATE ESM; ERASE EEP ROM CALIBRATION DATA IN TCM AND ALLOW IT TO RECALIBRATE. ALTIMA, ROGUE, SENTRA. *PE
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).