Original record summaries, dates and identifiers for this model-year. Records 201–300 of 669, ordered newest first. Dated records on this page: Nov 27, 2018–Mar 12, 2020.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Mar 12, 2020Service Bulletin/Repair Instructions
00-001-20-3689
NHTSA communication ID: 10173097
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The ownerâÂÂs manual contains procedures and precautions for the maintenance and cleaning of plastic parts, like the brand emblem. However, it is still important to remind customers about these precautions. Customers should never use inadequate, harsh or aggressive cleaning products on plastic parts. CAUTION: Be aware that when cleaning the brand emblem, never use cleaning products that are highly acidic/alkaline detergent, organic solvents or those with aggressive chemical products, otherwise, the brand emblem may become cracked and/or deformed (as shown in the example below). Always refer customers to the ownerâÂÂs manual for proper cleaning using cold or lukewarm water and a mild, neutral detergent.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may have one of the following DTCs stored in memory: ï· C1001:92 - Forward sensing camera (FSC) poor field of view ï· B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. ï· In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). ï· In other cases this DTC might be found without a related customer concern. NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. NOTE: The following Caution is included with every ATX that requires configuration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a groan noise from the front brakes when braking at a very low speed (approximately 6 mph / 10 km/h). This may be caused by a brake torque variation at that speed due to an inappropriate machining process of the brake disc surface. Customers having this concern should have their vehicle repaired using the following repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the steering wheel is off center more than 3ð even when driving straight on a flat road. Customers having this concern should have their vehicle repaired using the following repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed.ï· P2610:00: Instrument cluster internal engine off timer performance problem ï· P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display âÂÂF0-002â during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km).Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).
NHTSA source summary · Original PDF not reviewed by Recallfolio
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealerâÂÂs responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. ï· Mazda vehicles are manufactured with tamper-proof speedometers. ï· When a speedometer is replaced, the new speedometer will read zero (0) miles. ï· This procedure is extremely important to accurately represent actual vehicle mileage. ï· Prior to speedometer removal, complete the information required on the âÂÂSpeedometer Replacement LabelâÂÂ. Labels can only be ordered through Mazda eStore. ï· In an effort to achieve a higher level of Customer Experience and retain the value of MazdaâÂÂs vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOâÂÂs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.352 or later).
NHTSA source summary · Original PDF not reviewed by Recallfolio
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the oil cooler was missing altogether. IMPORTANT NOTE: ALWAYS REMEMBER TO INCLUDE THE ORIGINAL OIL COOLER WITH THE RETURNED TRANSMISSION CORE!
Source components: POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. âÂÂMazda Air Cooling Coil Coatingâ is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Bulletin is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GUIDE LINES AND PHOTOS TO DETERMINE IF FLUID/OIL SEEPAGE OR LEAK IS SEVERE ENOUGH TO REQUIRE WARRANTY REPAIR OR TO CLEAN AND MONITOR. Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about: ï· Intermittent engine no start ï· Instrument cluster red security indicator light ON ï· Engine Start/Start Button Amber indicator light flashing ï· Battery discharge ï· Electrical relay buzzing noise ï· DTC B13D3:94 (Communication error with remote transmitter) stored.This may be caused by: ï· A key in a purse near a cell phone. The cell phone radio waves may interrupt the immobilizer system. ï· An aftermarket cell phone charger. The charger may produce electrical noise that interrupts the immobilizer system. ï· An aftermarket GPS tracker. Some aftermarket devices that are wired to the vehiclesâÂÂs wiring harness may create unusual electrical symptoms.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint: ï· MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE ï· CANNOT COMMUNICATE WITH VEHICLE ï· ERROR MESSAGE INSTALLED ON ANDROID DEVICES ï· COMMUNICATION ERRORS ï· MMS CHECK MODE - Use to verify system operation (see below).
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may expierience one or more of the following: ï· intermittent no start ï· engine stall ï· many DTC's stored ï· no communication with the PCM. This may be caused by a poor C-11 or C-12 electrical connection.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a groan noise from the front brakes when braking at a very low speed (approximately 6 mph / 10 km/h). This may be caused by a brake torque variation at that speed due to an inappropriate machining process of the brake disc surface.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary:
NHTSA source summary · Original PDF not reviewed by Recallfolio
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about no cool air from the vents when the air conditioner (A/C) is ON. This concern may be caused by A/C refrigerant leaking from the evaporator at the joint between the tubes and the header due to improper brazing. To correct the problem, the configuration of the header has been changed to improve the brazing performance in this area.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
Source components: ENGINE AND ENGINE COOLING · STRUCTURE:BODY:HOOD.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
After the installation of a new instrument cluster, the message "Fctry" or âÃÂÃÂFactoryâÃÂàis displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required. NOTE: The concern is applicable to Calsonic Kansei instrument clusters. Not all trim levels are affected.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. Customers concern can be resolved by sanding off paint at ground point (3) where attachment bolt (4) is seated. After installing the bolt (4), apply touch-up paint to the exposed base material area of the front fender stay.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING · SERVICE BRAKES, HYDRAULIC · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may have a concern of a loose steering wheel. If a customer reports a loose steering wheel and the lock bolt is found to be loose, DO NOT simply re-tighten the steering wheel. Follow the steps below in the Repair Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may have one of the following DTCs stored in memory: C1001:92 - Forward sensing camera (FSC) poor field of view. B14F0:92 - General temporary failure in forward sensing camera (FSC). DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details. If the vehicle has this DTC, DO NOT replace the FSC. Read below.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit the cushion tape (1) attached to the front end of dashboard coming off and showing at the base of the windshield. This is caused by the cushion tape peeling off from the end(s) due to interference with the windshield and vehicle vibration (CX-5/Mazda6) or from the gap between the dashboard and the cushion tape because there there is no rib (1) at the dashboard ends (Mazda3). To prevent the tape from peeling off, both ends of the cushion tape are now folded over to the back side of the dashboard (CX-5/Mazda6) or stapled (Mazda3).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. The Recall can be performed after removing IDS 114 and installing IDS 113. This SA will be updated when more information is available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of MazdaâÂÂs continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software.Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit one of the following concerns: Sometimes the shifter may jump out of 3rd gear over a road bump when accelerating after deceleration at 25-40 mph (40-65 km/h), Hard to shift into 3rd, 4th, 5th, and/or 6th gear, Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
Source components: STEERING · STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil pressure switch No. 4 (oil pressure switch B) stuck on P0780:00 - Gear shifting malfunction P1738:00 - Automatic transaxle internal malfunction This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customer using âÃÂÃÂFlexibleâÃÂàsetting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MAZDA IDS INOPERATIVE WITH VCM-II LICENSE EXPIRATION MESSAGE - If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Reboot your PC, DO NOT start any application after restarting. 3. Run the resetting tool by double clicking the "Reset.bat" file (on your desktop from step 1). 4. Press any key after reading the notifications about the resetting tool.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. The noise: ï·Depends on the vehicleâÂÂs speed only (the more speed, the more noise)ï·Occurs with all types of driving (acceleration, deceleration, steady speed)ï·Does not depend on rpm, gear, or ATF temperature.This is caused by a damaged bearing in the transaxle due to improper configuration of the transaxle case. A modification has now been implemented on automatic transaxles with the following serial numbers: ï·7TN0820364 and higher (CX-3) / 8TN1090104 and higher (except CX-3) ï·8TR1008883 and higher ï·8TD1003276 and higher ï·8T50331192 and higher (CX-3) / 8T50329705 and higher (except CX-3).
Source components: POWER TRAIN · POWER TRAIN:AXLE ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a squeak noise from the right front driveshaft at the automatic transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the driveshaft. To correct this issue, the thickness of the dust cover has been increased.
Source components: POWER TRAIN:DRIVELINE:DRIVESHAFT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear in certain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When pressing the START/STOP button in very cold weather, the ignition may not turn off on some vehicles equipped with a lock release button (1) on the selector lever knob. Although the selector lever is in the "P" position and the engine shuts off normally, the ignition may stay on (in accessory mode). NOTE: This TSB only applies if the selector lever knob is BHN2-46-030* or BHN4-46-030* with the lock release button. If not, this TSB does not apply. This may be caused by the lock release button in the selector lever knob sticking in the pressed position. An improper production process is causing an internal part to expand with moisture and interfere with other parts. To eliminate this concern, the production process has been modified.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:IGNITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customer using "Flexible" setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed.
Source components: ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is fully turned to the driver-side (left side for LHD vehicle and right side for RHD vehicle). NOTE: The noise will not occur if the steering wheel is in the center or to the full passenger-side position.The noise is caused when the edge (A) of the inner ball joint (B) gets stuck with the steering gear housing(C). To eliminate the noise, a spacer (A) has been installed between the inner ball joint (B) and the steering gear housing (C) (both sides) to prevent direct contact.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH® hands-free unit or text messaging related concerns. To improve the handling of BLUETOOTH® hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of the following DTC(s) stored in memory. P0300 - Random misfire detected P0301 - Cylinder No. 1 misfire detected P0302 - Cylinder No. 2 misfire detected P0303 - Cylinder No. 3 misfire detected P0304 - Cylinder No.4 misfire detected. This may be caused by frozen water accumulated in the main silencer, restricting exhaust flow.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH® hands-free unit or text messaging related concerns. To improve the handling of BLUETOOTH® hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit. Tool Number Description Pricing PC1923MAZ Pro-Cut On-Car Brake Lathe Check eStore or call for current pricing OBTAINING TOOLS This tool can be ordered through Mazda eStore. You can log on to eStore at: http://dealers.mazdausa.com CUSTOMER SERVICE INFORMATION For warranty or product information contact Mazda Authorized Service Equipment at 877-768-6657. Customer service representatives are available from 7:30 AM until 7:00 PM CST, Monday through Friday. SPECIAL SERVICE TOOL (SST) PART NAME: OVERVIEW Pro-Cut On-Car Brake Lathe PART NUMBER: PC1923MAZ APPLICABLE MODELS: All USAGE: To machine brake rotors on the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle- specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Refer to DAG Exchange Central (MXConnect>Parts and Accessories>Parts>Programs>Exchange Central) for component availability, source of technical support and prior authorization requirement. NOTE: Always check for a TSB that may modify or eliminate prior authorization for a specific symptom for a given component.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazda models, there is no key cylinder on the steering column. Therefore, the engine cannot be started with the auxiliary key if the room fuse is removed or if the transmitter battery is dead.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak). The concern is most likely the result of the customer not getting the fuel cap completely closed after fueling the vehicle. This causes a small fuel vapor leak and turns DTC P0456 on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear in certain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with active working SAT radio.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction Detection Function" initial check and that there is no problem. This initial checkis a necessary function to ensure the normal operation of the ABS/TCS/DSC system. It occurs when the vehicles first moves forward under the following conditions. NOTE: Some customers may describe that the noise does not occur all the time. It does occur all the time, but the sound is more likely to be heard on a slow start and not on a quick start (quick acceleration) when engine noise is louder.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps):CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery's Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda GR8-1291, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. If your dealer does not have a GSP9700 or equivalent balance machine, sublet the vehicle out for repair. To find the location of a GSP9700 near your dealer, visit Hunter?s web site at www.gsp9700.com and click on ?Locate a GSP9700 Road Force Balancer.?
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the navigation brand icons are no longer shown after a navigation SD card update. This is caused by a navigation map supplier software change. Customers can set preferences if needed. Example: A customer may have a Shell Gas Card and is only interested in Shell Gas Stations. The customer can set preference to only show Shell gas stations.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition. Album art and artist biographies are not provided by SiriusXM Satellite Radio, a blank white square frame is shown in place of the album art. Note: This information is also available at www.mazdahandsfree.com>FAQ>ENTERTAINMENT - SIRIUSXM®. STATION LOGO SIRIUSXM satellite radio hardware is in the Tuner and Amp Unit (TAU). The station logo is not shown in the center display because there is no visual data communication cable between the TAU and the Connectivity Master Unit (CMU). A blank white square frame is shown in place of the station logo. Do NOT perform any repairs for these concerns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit the cushion tape (1) attached to the front end of dashboard coming off and showing at the base of the windshield.This is caused by the cushion tape peeling off from the end(s) due to interference with the windshield and vehicle vibration. To prevent the tape from peeling off, both ends of the cushion tape are now folded over to the back side of the dashboard or stapled depending on the model.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth® and the same device is also connected to the USB port for charging. The concerns may include: Blank Screen and/or No Audio Sound, Phone will not charge.Blank Screen and/or No Audio Sound These concerns may be caused by:The MAZDA CONNECT system has reached its capacity limits when streaming music with audio source aha/Pandora/Stitcher/Bluetooth® and also connected to the USB port.The MAZDA CONNECT system has reached its capacity limits when the customer's USB device capacity exceeds 16 GB (e.g. 64 GB iPhone X). The MAZDA CONNECT system USB port capacity is 16 GB (FAT32).Mazda recommends not to connect any devices to the USB port when streaming music with audio source aha/Pandora/Stitcher/Bluetooth®. When streaming music with audio source aha/Pandora/Stitcher/Bluetooth® (without USB connection), the Connectivity Master Unit (CMU) is able to process Bluetooth® digital data (A) and output audio sound and display Bluetooth® audio information. If the same device is connected to the USB port for charging, the CMU processes both Bluetooth® digital data (A) and USB digital data (B) from the same device at the same time. In this case, CMU resources may be exceeded, causing a Blank Screen and/or No Audio Sound.
NHTSA source summary · Original PDF not reviewed by Recallfolio
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin.Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.100A or later). NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SMS (Short Message Service) messages received by paired phones (Android and iPhone 5 iOS 7.0 or higher) can be downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. When parked, new messages can be displayed or read by the system. When driving, new messages can be read to the vehicle occupants.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. This can happen if the ignition is turned OFF within 20 seconds after the ignition is turned ON in one of the following two situations. 1. The ?ROOM? fuse (Engine compartment) is NOT installed when battery level is low. 2. The CMU (Connectivity Master Unit) is NOT connected.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SMS (Short Message Service) messages received by paired phones (Android and iPhone 5 iOS 7.0 or higher) can be downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. When parked, new messages can be displayed or read by the system. When driving, new messages can be read to the vehicle occupants.