Original record summaries, dates and identifiers for this model-year. Records 501–600 of 608, ordered newest first. Dated records on this page: Jan 30, 2014–Mar 26, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Mar 26, 2015Service Bulletin/Repair Instructions
09-008-15-2991B
NHTSA communication ID: 10099686
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE EFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. C. IPOD ERROR MESSAGE FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6. THESE CONCERNS MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. THESE CONCERN MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME. THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDSFREE MODULE WILL NOT ADDRESS THE IPOD ERROR MESSAGE CONCERN FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6 AT THIS TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT INSTRUMENT CLUSTER TPMS, ABS AND TCS/DSC INDICATOR WARNING LIGHTS ON AND DTC U3000:49[STANDARD DEPLOYMENT CONTROL SYSTEM] OR C0061:29, C0062:29, C0063:29 [STANDARD DEPLOYMENT CONTROL SYSTEM] STORED IN MEMORY. THE AIRBAG, SCBS, AT, MRCC, LDWS AND HBC INSTRUMENT CLUSTER INDICATOR LIGHTS MAY ALSO COME ON. INTERNAL FAILURE OF THE SAS CONTROL MODULE MAY BE THE CAUSE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AFTER PERFORMING RECALL CAMPAIGN 8014J, OR THE VEHICLE VIN IS NOT APPLICABLE TO 8014J, SOME VEHICLES MAY EXPERIENCE TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. THIS MAY BE CAUSED BY IMPROPER TIRE AIR PRESSURE DETECTION BY THE TPMS SYSTEM ON CERTAIN TYPES OF ROAD SURFACES.
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
USE THE FOLLOWING REPAIR PROCEDURE TO MINIMIZE THE NEED TO REPLACE THE CATALYST CONVERTER/EXHAUST PIPE WHEN REMOVING OXYGEN SENSORS AND/OR AIR FUEL RATIO SENSORS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE STAINS APPEARING ON THE HOOD, ROOF AND/OR TRUNK OF THE VEHICLE. THIS CONCERN IS MOST LIKELY TO BE FOUND IN A COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEEN THE PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH A HEAT GUN OR AN INFRARED DRIER. IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE A HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED AREA TO REMOVE THE STAIN(S).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. THESE CONCERN MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY HAVE THE BLIND SPOT MONITORING (BSM) OFF INDICATOR LIGHT FLASHING AND DTC U3000:54 STORED IN MEMORY. THE CONCERN IS CAUSED BY INADEQUATE BSM CONTROL MODULE CONTROL LOGIC. THE BSM CONTROL MODULE SOFTWARE HAS BEEN UPDATED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT STRUT BEARING (A) WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO UPPER FRONT STRUT BEARING DAMAGE OR IT MAY BE DUE TO STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE: 1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING HAS BEEN CHANGED. 2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. NOTE: THE PISTON ROD NUT (B) REQUIRES REPLACEMENT WHEN THE FRONT STRUT BEARING IS REPLACED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT AN INOPERATIVE SEAT WARMER (OR SEAT HEATER) ON THE DRIVER AND/OR PASSENGER SEAT. WHEN WEIGHT IS APPLIED TO THE SEAT, PART OF THE HEATER ELEMENT WIRE MAY COME OUT OF POSITION AND BECOME BENT. UNDER REPEATED STRESS, THE WIRE MAY BREAK CAUSING AN INOPERATIVE SEAT WARMER CONDITION. AN ADDITIONAL ADHESION TREATMENT HAS BEEN APPLIED TO ELIMINATE THE HEATER ELEMENT WIRE FROM COMING OUT OF THE POSITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT NO COOL AIR FROM THE VENTS WHEN THE AIR CONDITIONER (A/C) IS ON. THIS CONCERN MAY BE CAUSED BY A/C REFRIGERANT LEAKING FROM THE EVAPORATOR. SOME DEFORMED EVAPORATOR TUBES SLIPPED THROUGH QUALITY INSPECTION AND WERE USED DURING PRODUCTION. A/C REFRIGERANT LEAKS FROM IMPROPER BRAZING AT A JOINT. TO CORRECT THE PROBLEM, THE PRODUCTION AND INSPECTION CONTROL OF THE EVAPORATOR HAVE BEEN IMPROVED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AFTER PERFORMING RECALL CAMPAIGN 8014J, SOME VEHICLES MAY EXPERIENCE TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. THIS MAY BE CAUSED BY IMPROPER TIRE AIR PRESSURE DETECTION BY THE TPMS SYSTEM ON CERTAIN TYPES OF ROAD SURFACES.
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A CREAKING NOISE FROM UNDER THE FRONT OF THE VEHICLE WHEN DRIVING OVER BUMPS. THE NOISE OCCURS AT APPROX. 12 - 25 MPH (20 - 40 KM/H) WHEN THE ROAD SURFACE IS WET OR AFTER A CAR WASH. THE NOISE BECOMES MORE NOTICEABLE WHEN DRIVING OVER HIGHER BUMPS. THE CREAKING NOISE IS CAUSED WHEN THE FRONT LOWER CONTROL ARM BUSHING(S) (A) BECOME WET.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR. SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) THIS IS CAUSED BY A FAILURE OF THE RELATED CLUTCH HUB(S). TO CORRECT THE PROBLEM OF HARD SHIFTING, THE SHAPE OF THE 3-4 AND 5-6 CLUTCH HUB HAS BEEN CHANGED. A SURFACE TREATMENT HAS NOW BEEN ADDED TO THE 3-4 CLUTCH HUB TO PREVENT 3RD GEAR FROM JUMPING OUT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A CHIRP/CLUNK TYPE NOISE FROM THE REAR SHOCK ABSORBERS (A) WHEN DRIVING ON A ROUGH ROAD OR PASSING OVER A SPEED BUMP. VISUAL INSPECTION OF THE SHOCK ABSORBERS SHOW NO EXTERNAL DAMAGE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AFTER PERFORMING RECALL CAMPAIGN 8014J, SOME VEHICLES MAY EXPERIENCE TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. THIS MAY BE CAUSED BY IMPROPER TIRE AIR PRESSURE DETECTION BY THE TPMS SYSTEM ON CERTAIN TYPES OF ROAD SUR-FACES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A CREAKING NOISE FROM UNDER THE FRONT OF THE VEHICLE WHEN DRIVING OVER BUMPS. THE NOISE OCCURS AT APPROX. 12 - 25 MPH (20 - 40 KM/H) WHEN THE ROAD SURFACE IS WET OR AFTER A CAR WASH. THE NOISE BECOMES MORE NOTICEABLE WHEN DRIVING OVER HIGHER BUMPS. THE CREAKING NOISE IS CAUSED WHEN THE FRONT LOWER CONTROL ARM BUSHING(S) (A) BECOME WET.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IN SUPPORT OF THE SKYACTIV MODELS, MAZDA WILL MAKE AVAILABLE A SPECIAL SERVICE TOOL (SST), TO ADDRESS FRONT SUSPENSION NOISE FOR SPECIFIC HIGH HUMIDITY AND WET CLIMATE CONDITIONS IN THE LOWER GULF STATES. THE SST WILL BE NEEDED TO COMPLETE REPAIRS DETAILED IN TSB 02-005/14 AND IS AVAILABLE THROUGH MAZDAS TOOL VENDOR, SNAP-ON TOOLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR. SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) THIS IS CAUSED BY A FAILURE OF THE RELATED CLUTCH HUB(S). TO CORRECT THE PROBLEM OF HARD SHIFTING, THE SHAPE OF THE 3-4 AND 5-6 CLUTCH HUB HAS BEEN CHANGED. A SURFACE TREATMENT HAS NOW BEEN ADDED TO THE 3-4 CLUTCH HUB TO PREVENT 3RD GEAR FROM JUMPING OUT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN DEALING WITH CUSTOMER COMPLAINTS OF EXCESSIVE CONDENSATION AND/OR WATER WITHIN THE HEADLAMP UNIT, FIRST DETERMINE IF ALL THE BULB SOCKETS ARE PRESENT AND CORRECTLY INSTALLED. IN MOST CASES YOU WILL FIND THAT THE BULB SEAL NO. 1 (A) OR HID BULB SEAL NO. 1 (B) AND BULB SEAL NO. 2 (C) SOCKET COVERS HAVE NOT BEEN CORRECTLY INSTALLED OR ARE MISSING DUE TO IMPROPER PRIOR REPAIRS (I.E., CUSTOMER REPLACING THE HEADLAMP BULBS OR BODY SHOP NOT TRANSFERRING THEM WHEN REPLACING THE HEADLAMP UNIT(S) DUE TO A COLLISION). ANY DAMAGE CAUSED BY MISSING SOCKET COVERS, HID MODULE SEAL (D), OR MISSING BUMPER BRACKETS (E) IS NOT COVERED BY WARRANTY POLICY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.854 OR LATER).NAVIGATION SYSTEM FREEZES.MESSAGE WAITING FOR VALID GPS SIGNAL IS SHOWN IN THE MENU BAR OF NAVIGATION DISPLAY FOR SEVERAL MINUTES.VEHICLE SYMBOL IS OFF ROAD WHILE DRIVING / WRONG POSITION OF VEHICLE ON MAP.MAP IS ROTATING WHEN VEHICLE IS PARKED OR WHILE DRIVING.NAVIGATION SCREEN DONT APPEAR AFTER DEPRESSING NAVIGATION BUTTON. THEN IT DOES NOT RECOVER BY OPERATING ACC OFF TO ON POSITION.UNEXPECTED STOPPING VOICE CONTROL MESSAGE, USUALLY WHEN STARTING THE VEHICLE.CURRENT CAR POSITION (CCP) TURNING 180 DEGREES WHEN DRIVING IN REVERSE.THE MESSAGE WAITING FOR A VALID GPS SIGNAL APPEARS.RED SCREEN WITH MESSAGE "PROBLEM WITH MAP".YELLOW SCREEN WITH MESSAGE "INSERT SD CARD".NO MAP FOUND ERROR AND SD CARD CONTAINS A MAP.SCREEN TEMPORARILY GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) FOR 2 MINUTES DURING STARTUP. AFTERWARDS, THE NAVIGATION WILL NOT START UNTIL THE IGNITION IS CYCLED.SCREEN GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) DURING STARTUP.SCREEN LOCKS UP TO A "BLACK SCREEN.VEHICLE ICON JUMPS AROUND OR VIBRATES.IF NAVIGATION BUTTON IS PRESSED DURING AUDIO SCREEN, THE SCREEN FREEZES AND THE TOUCH SCREEN BECOMES INOPERATIVE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE FUEL GAUGE SHOWS EMPTY AND/OR THE DISTANCE-TO-EMPTY ON THE MULTI-INFORMATION DISPLAY (MID) INDICATES 0 WITH A CERTAIN AMOUNT OF FUEL REMAINING IN THE TANK.THIS MAY BE A NORMAL OPERATION OF THE FAIL-SAFE FUNCTION:1.IF FOREIGN MATERIAL (CONTAINED IN A POOR-QUALITY FUEL) ADHERES TO THE FUEL GAUGE SENDER UNIT, THE FAIL-SAFE FUNC-TION INITIATES BY FORCING THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY TO INDICATE ZERO FUEL AMOUNT.2.IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED BY SHAKING OF THE FUEL DURING DRIVING OR REFUELING, THE FUEL GAUGE WILL RETURN TO A NORMAL READING, BUT THE DISTANCE-TO-EMPTY WILL CONTINUE TO READ 0 UNTIL THE NEXT REFUEL-ING OF 3 US GALLONS (10 LITERS) OR MORE.TO CORRECT THE PROBLEM THE FOLLOWING CHANGE HAS BEEN MADE:1.THERE IS NO MASS-PRODUCTION CHANGE TO PREVENT ADHESION OF FOREIGN MATERIAL TO THE FUEL GAUGE SENDER UNIT. SO THE FACT REMAINS UNCHANGED THAT THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY INDICATE ZERO FUEL AMOUNT WHEN FOREIGN MATERIAL ADHERES TO THE FUEL GAUGE SENDER UNIT, AND THE FAIL-SAFE FUNCTION INITIATES.2.TO EQUALIZE THE RECOVERY TIMING FROM THE FAIL-SAFE MODE, THE LOGIC HAS BEEN CHANGED SO THAT THE DISTANCE-TO-EMPTY RECOVERS FROM 0 TO A NORMAL READING IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED (AT THE SAME TIME AS THE FUEL GAUGE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE FUEL GAUGE SHOWS EMPTY AND/OR THE DISTANCE-TO-EMPTY ON THE MULTI-INFORMATION DISPLAY (MID) INDICATES 0 WITH A CERTAIN AMOUNT OF FUEL REMAINING IN THE TANK.THIS MAY BE A NORMAL OPERATION OF THE FAIL-SAFE FUNCTION:1.IF FOREIGN MATERIAL (CONTAINED IN A POOR-QUALITY FUEL) ADHERES TO THE FUEL GAUGE SENDER UNIT, THE FAIL-SAFE FUNC-TION INITIATES BY FORCING THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY TO INDICATE ZERO FUEL AMOUNT.2.IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED BY SHAKING OF THE FUEL DURING DRIVING OR REFUELING, THE FUEL GAUGE WILL RETURN TO A NORMAL READING, BUT THE DISTANCE-TO-EMPTY WILL CONTINUE TO READ 0 UNTIL THE NEXT REFUEL-ING OF 3 US GALLONS (10 LITERS) OR MORE.TO CORRECT THE PROBLEM THE FOLLOWING CHANGE HAS BEEN MADE:1.THERE IS NO MASS-PRODUCTION CHANGE TO PREVENT ADHESION OF FOREIGN MATERIAL TO THE FUEL GAUGE SENDER UNIT. SO THE FACT REMAINS UNCHANGED THAT THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY INDICATE ZERO FUEL AMOUNT WHEN FOREIGN MATERIAL ADHERES TO THE FUEL GAUGE SENDER UNIT, AND THE FAIL-SAFE FUNCTION INITIATES.2.TO EQUALIZE THE RECOVERY TIMING FROM THE FAIL-SAFE MODE, THE LOGIC HAS BEEN CHANGED SO THAT THE DISTANCE-TO-EMPTY RECOVERS FROM 0 TO A NORMAL READING IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED (AT THE SAME TIME AS THE FUEL GAUGE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY EXPERIENCE ONE OR MORE OF THE FOLLOWING CLOCK SYMPTOM(S):THE CLOCK RESETS TO 1:00 BY ITSELF.THE CLOCK DISPLAY IS BLANK.THE CLOCK DISPLAY FREEZES.THE CLOCK DISPLAYS A WRONG TIME.INTERNAL FAILURE OF THE CLIMATE CONTROL UNIT MAY BE THE CAUSE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE STEERING WHEEL IS OFF CENTER MORE THAN 3° EVEN WHEN DRIVING STRAIGHT ON A FLAT ROAD. FOLLOW STEERING WHEEL ALIGNMENT PROCEDURE.
Source components: STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.854 OR LATER).NAVIGATION SYSTEM FREEZES.MESSAGE WAITING FOR VALID GPS SIGNAL IS SHOWN IN THE MENU BAR OF NAVIGATION DISPLAY FOR SEVERAL MINUTES.VEHICLE SYMBOL IS OFF ROAD WHILE DRIVING / WRONG POSITION OF VEHICLE ON MAP.MAP IS ROTATING WHEN VEHICLE IS PARKED OR WHILE DRIVING.NAVIGATION SCREEN DONT APPEAR AFTER DEPRESSING NAVIGATION BUTTON. THEN IT DOES NOT RECOVER BY OPERATING ACC OFF TO ON POSITION.UNEXPECTED STOPPING VOICE CONTROL MESSAGE, USUALLY WHEN STARTING THE VEHICLE.CURRENT CAR POSITION (CCP) TURNING 180 DEGREES WHEN DRIVING IN REVERSE.THE MESSAGE WAITING FOR A VALID GPS SIGNAL APPEARS.RED SCREEN WITH MESSAGE "PROBLEM WITH MAP".YELLOW SCREEN WITH MESSAGE "INSERT SD CARD".NO MAP FOUND ERROR AND SD CARD CONTAINS A MAP.SCREEN TEMPORARILY GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) FOR 2 MINUTES DURING STARTUP. AFTERWARDS, THE NAVIGATION WILL NOT START UNTIL THE IGNITION IS CYCLED.SCREEN GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) DURING STARTUP.SCREEN LOCKS UP TO A "BLACK SCREEN.VEHICLE ICON JUMPS AROUND OR VIBRATES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY HAVE THE BLIND SPOT MONITORING (BSM) OFF INDICATOR LIGHT FLASHING AND DTC U3000:54 STORED IN MEMORY.THE CONCERN IS CAUSED BY INADEQUATE BSM CONTROL MODULE CONTROL LOGIC. THE BSM CONTROL MODULE SOFTWARE HAS BEEN UPDATED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT NO COOL AIR FROM THE VENTS WHEN THE AIR CONDITIONER (A/C) IS ON. THIS CON-CERN MAY BE CAUSED BY A/C REFRIGERANT LEAKING FROM THE EVAPORATOR. SOME DEFORMED EVAPORATOR TUBES SLIPPED THROUGH QUALITY INSPECTION AND WERE USED DURING PRODUCTION. A/C REFRIGERANT LEAKS FROM IMPROPER BRAZING AT A JOINT. TO CORRECT THE PROBLEM, THE PRODUCTION AND INSPECTION CONTROL OF THE EVAPORATOR HAVE BEEN IMPROVED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE MIL ILLUMINATION WITH DTC P2610 (INSTRUMENT CLUSTER INTERNAL ENGINE OFF TIMER PERFORMANCE PROBLEM) STORED IN MEMORY AFTER ENGINE START AND ROOM FUSE 15A (A) REMOVED. NOTE:THE ODOMETER WILL DISPLAY F0-002 DURING TRANSPORT MODE (ROOM FUSE 15A REMOVED). TRANSPORT MODE IS CANCELED WHEN ROOM FUSE 15A IS INSTALLED OR THE VEHICLE ODOMETER IS MORE THAN 12.4MI (20KM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
IN SUPPORT OF SKYACTIV MANUAL TRANSMISSION MODELS, MAZDA WILL SHIP TO ALL DEALERS ONE (1) NEW SPECIAL SER-VICE TOOL (SST). THE SST WILL BE SHIPPED AUTOMATICALLY BY MAZDAS TOOL VENDOR SNAP-ON TOOLS, STARTING IN MID-OCTOBER 2014.THE FOLLOWING SST IS THE LATEST ADDITION TO THE MAZDA REQUIRED TOOL (MRT) LIST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS SERVICE INFORMATION PROVIDES BASIC Q-85/T-110 BATTERY HANDLING PROCEDURES. COMPLETE SERVICE INFORMATION CAN BE FOUND IN MS3 ONLINE OR WORKSHOP MANUAL (SECTION 01-17).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT BLUETOOTH® HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THE HANDLING OF BLUETOOTH® HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY HAVE THE BLIND SPOT MONITORING (BSM) OFF INDICATOR LIGHT FLASHING AND DTC U3000:54 STORED IN MEMORY.THE CONCERN IS CAUSED BY INADEQUATE BSM CONTROL MODULE CONTROL LOGIC. THE BSM CONTROL MODULE SOFTWARE HAS BEEN UPDATED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A WIND NOISE FROM THE DOOR WINDOW EDGE(S), WHILE DRIVING. THE WIND NOISE IS MOST PRONOUNCED AT APPROXIMATELY 50 MPH (81 KM/H) ON A SMOOTH ROAD. THE WIND NOISE MAY BE CAUSED BY AIR PASS-ING THROUGH GAPS BETWEEN THE DOOR EDGE AND THE CORRESPONDING BODY PANEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY FIND IT DIFFICULT OR HARD TO MOVE THE A/T SHIFT LEVER. WHEN THE DRIVER OR FRONT PASSENGERS LEG CONTACTS THE CENTER CONSOLE, LATERAL FORCE (A) MAY DEFORM THE INDICATOR SLIDER (B), CAUSING THE SLIDER EDGE TO CONTACT THE ARCHED PART OF THE SET PLATE (D). THIS MAY CAUSE DAMAGE TO THE INDICATOR SLIDER (B) AND/OR HARD A/T SHIFT LEVER MOVEMENT.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IN ACCORDANCE WITH FEDERAL REGULATIONS, FOLLOW THE PROCEDURE LISTED BELOW WHEN REPLACING A SPEEDOMETER.NOTE:MAZDA VEHICLES ARE MANUFACTURED WITH TAMPER-PROOF SPEEDOMETERS.WHEN A SPEEDOMETER IS REPLACED, THE NEW SPEEDOMETER WILL READ ZERO (0) MILES.THIS PROCEDURE IS EXTREMELY IMPORTANT TO ACCURATELY REPRESENT ACTUAL VEHICLE MILEAGE.PRIOR TO SPEEDOMETER REMOVAL, COMPLETE THE INFORMATION REQUIRED ON THE SPEEDOMETER REPLACE-MENT LABEL. LABELS CAN ONLY BE ORDERED THROUGH MSTORE, NOT MDCS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY EXPERIENCE THE FOLLOWING SYMPTOM:A.WARNING MESSAGE I-ELOOP MALFUNCTION (MAZDA3) OR I-ELOOP INSPECTION REQUIRED (MAZDA6) IS DIS-PLAYED IN THE INSTRUMENT CLUSTER INFORMATION DISPLAY WHILE DRIVING.B.THE MASTER WARNING LIGHT AND CHARGING SYSTEM WARNING LIGHT ILLUMINATE. C.DTC P1794:00 (CAPACITOR (I-ELOOP) SYSTEM: CAPACITOR (I-ELOOP) MALFUNCTION) IS STORED IN PCM MEMORY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MAZDA: SOME VEHICLES ARE EXPERIENCING AN ILLUMINATION OF MASTER WARNING LIGHT AND CHARGING SYSTEM WARNING LIGHT AND INSTRUMENT CLUSTER INFORMATION DISPLAYING, WHILE DRIVING, I-ELOOP INSPECTION IS REQUIRED. MODEL 2014-2015 MAZDA3, MAZDA6. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A GROAN TYPE NOISE FROM THE FRONT WHEEL HUB BEARING WHILE DRIVING AT HIGH SPEED OR WHEN CORNERING. THIS MAY BE CAUSED BY FRONT WHEEL HUB BEARING CORROSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS:HARD TO SHIFT INTO 3RD GEARSOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H)THIS IS CAUSED BY THE FRICTION COEFFICIENT BETWEEN THE 3/4 CLUTCH HUB AND THE SLEEVE INCREASING. A SURFACE TREAT-MENT HAS NOW BEEN ADDED TO THE 3/4 CLUTCH HUB TO DECREASE THE FRICTION COEFFICIENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS SERVICE BULLETIN PROVIDES INFORMATION REGARDING THE PROPER USE OF THE DRIVERS FLOOR MAT TO AVOID ANY POTENTIAL INTERFERENCE WITH THE FOOT PEDALS. THE FOLLOWING ARE POSSIBLE CAUSES OF FLOOR MAT INTERFERENCE, WHICH CAN BE AVOIDED WITH PROPER USAGE. FLOOR MAT MOVES FORWARD DUE TO IMPROPER INSTALLATION. INAPPROPRIATE FLOOR MAT (SUCH AS AFTERMARKET, NON-FACTORY-EQUIPPED, OR NON-GENUINE) IS USED. FLOOR MAT IS STACKED ONE ON TOP OF ANOTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MAZDA NORTH AMERICAN OPERATIONS RECEIVED MANY REQUESTS FROM OUR DEALERS ASKING US TO APPROVE ADDITIONAL ON-CAR BRAKE LATHES AS AN OPTION FOR MNAO AUTHORIZED EQUIPMENT. DUE TO YOUR FEEDBACK AND AFTER EVALUATING A FEW ON-CAR BRAKE LATHES, WE ARE PLEASED TO ANNOUNCE THAT WE HAVE ADDED THE PRO CUT ON-CAR BRAKE LATHE TO MNAO AUTHORIZED EQUIPMENT PROGRAM. THE ACCU-TURN IS STILL AN APPROVED BRAKE LATHE BUT IT IS NO LONGER AVAILABLE FOR PURCHASE FROM OUR VENDOR. IMPORTANT REMINDER ROTORS MUST BE MACHINED USING A MAZDA APPROVED ON-CAR BRAKE LATHE OR WARRANTY CLAIMS ARE SUBJECT TO DENIAL OR DEBIT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY EXPERIENCE AN ELECTRICAL MALFUNCTION AFTER A VEHICLE BODY REPAIR. THE NEWLY PAINTED FENDER STAY (B) MAY BE CAUSING A POOR FRONT HARNESS (A) GROUND CONNECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY EXPERIENCE AN ELECTRICAL MALFUNCTION AFTER A VEHICLE BODY REPAIR. THE NEWLY PAINTED FENDER STAY (B) MAY BE CAUSING A POOR FRONT HARNESS (A) GROUND CONNECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE AMBIENT TEMPERATURE DISPLAY IS NOT ACCURATE, OR IT TAKES TOO LONG FOR THE DISPLAY TO SHOW ACTUAL TEMPERATURE.WHEN YOU ENCOUNTER A CUSTOMER WITH THIS CONCERN, FIRST VERIFY THE CONDITION WHEN THE CUSTOMER NOTICED THIS SYMPTOM. IF THE CONDITION IS SIMILAR TO THE FOLLOWING CONTROL LOGIC OF AMBIENT TEMPERATURE OR DIF-FERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS, ADVISE THE CUSTOMER THAT THIS IS A NOR-MAL CHARACTERISTIC OF THE VEHICLE AND NOT A MALFUNCTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES EXHIBIT BRAKE RELATED CONCERNS SUCH AS BRAKE NOISE, BRAKE JUDDER OR BRAKE DRAGGING. IF YOU ENCOUNTER A CUSTOMER COMPLAINT FOR ANY ONE OF THESE SYMPTOMS, REFER TO THE FOLLOWING INFORMATION TO UNDERSTAND WHY SYMPTOMS MAY OCCUR, AND TO BETTER ASSIST THE CUSTOMER IN RESOLVING THEIR SPECIFIC BRAKE CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY EXPERIENCE ONE OF THE FOLLOWING TWO SYMPTOMS:1. SYMPTOM (MAZDA6 ONLY)A.WARNING MESSAGE I-ELOOP INSPECTION REQUIRED IS DISPLAYED IN THE INSTRUMENT CLUSTER INFORMATION DISPLAY WHILE DRIVING.B.THE MASTER WARNING LIGHT WILL BE ILLUMINATED. C.DTC P1794:00 (CAPACITOR (I-ELOOP) SYSTEM: CAPACITOR (I-ELOOP) MALFUNCTION) WILL BE STORED IN PCM MEM-ORY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY.P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONTHE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER.P0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION. NOTE: THIS SERVICE INFORMATION IS ALSO APPLICABLE IF DTC P0780:00 IS STOREED INDEPENDENTLY. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.852 OR LATER). VEHICLE ICON JUMPS AROUND OR VIBRATES. CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. OTHERWISE, PERSONAL SETTINGS (SUCH AS DISPLAY AND SOUND ADJUSTMENTS) WILL BE LOST, INCLUDING FAVORITES INFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY.P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONTHE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER.P0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY.P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONTHE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER.P0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.852 OR LATER). VEHICLE ICON JUMPS AROUND OR VIBRATES. CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. OTHERWISE, PERSONAL SETTINGS (SUCH AS DISPLAY AND SOUND ADJUSTMENTS) WILL BE LOST, INCLUDING FAVORITES INFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY. P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON THE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER. P0780:00 - GEAR SHIFTING MALFUNCTION P1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY. P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON THE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER. P0780:00 - GEAR SHIFTING MALFUNCTION P1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OF THE FOLLOWING SYMPTOMS WHEN THE VEHICLE IS STOPPED AND THE TRANSMISSION IS IN D RANGE: AN INTERMITTENT HIGH ENGINE IDLE SPEED. AN INTERMITTENT ENGAGEMENT SHOCK. AN INTERMITTENT FORWARD LURCH. THESE CONDITIONS MAY OCCUR WHEN THE CUSTOMER DEPRESSES THE BRAKE PEDAL AND MAKES CONTACT WITH THE THROTTLE PEDAL SIMULTANEOUSLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY EXPERIENCE ONE OF THE FOLLOWING TWO SYMPTOMS: 1. SYMPTOM (MAZDA6 ONLY) A. WARNING MESSAGE I-ELOOP INSPECTION REQUIRED IS DISPLAYED IN THE INSTRUMENT CLUSTER INFORMATION DISPLAY WHILE DRIVING. B. THE MASTER WARNING LIGHT WILL BE ILLUMINATED.C. DTC P1794:00 (CAPACITOR (I-ELOOP) SYSTEM: CAPACITOR (I-ELOOP) MALFUNCTION) WILL BE STORED IN PCM MEMORY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS SERVICE INFORMATION PROVIDES BASIC Q-85/T-110 BATTERY HANDLING PROCEDURES. COMPLETE SERVICE INFORMATION CAN BE FOUND IN MS3 ONLINE OR WORKSHOP MANUAL (SECTION 01-17).
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN REPLACING THE SIRIUSXM SATELLITE RADIO UNIT (OR A MAZDA CONNECT TUNER AND AMP UNIT (TAU)) WITH REPLACEMENT TUNER FOR ANY REASON, A CALL MUST BE MADE TO INFORM SIRIUSXM OF THE EXISTING RADIO ID AND THE NEW/ REPLACEMENT SAT RADIO ID AS SOON AS POSSIBLE TO ENSURE THE CUSTOMER LEAVES THE DEALERSHIP WITH ACTIVE (WORKING SAT RADIO.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS SERVICE INFORMATION PROVIDES BASIC Q-85/T-110 BATTERY HANDLING PROCEDURES. COMPLETE SERVICE INFORMATION CAN BE FOUND IN MS3 ONLINE OR WORKSHOP MANUAL (SECTION 01-17).
NHTSA source summary · Original PDF not reviewed by Recallfolio
THE NAVIGATION SYSTEM SUPPORT FOR DIAGNOSTICS, PARTS AUTHORIZATION, AND PARTS EXCHANGE REQUIRE CONTACTING THE PROPER SOURCE. TOMTOM NAVIGATION HELP DESK AT 866-486-6866 FROM 7AM-11PM (M-F) AND 9AM-8PM (SAT) EASTERN STANDARD TIME. NOTE: ONE OF THE FIRST STEPS FOR TROUBLESHOOTING THE NAVIGATION SYSTEM IS FOR THE CUSTOMER OR DEALER TO CALL TOMTOM. IF THE TOMTOM CALL CENTER CANNOT SOLVE THE CUSTOMERS PROBLEM, THEY WILL PROVIDE A CASE NUMBER TO THE CUSTOMER THAT CAN BE REFERRED TO IF NEEDED. SERVICE ADVISORS SHOULD GET THIS CASE NUMBER FROM THE CUSTOMER IF THE VEHICLE COMES INTO THE DEALER FOR FURTHER DIAGNOSIS SO THE TECHNICIAN CAN HAVE IT WHEN CALLING TOMTOM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY EXPERIENCE ONE OF THE FOLLOWING TWO SYMPTOMS: 1. SYMPTOM (MAZDA6 ONLY) A. WARNING MESSAGE I-ELOOP INSPECTION REQUIRED IS DISPLAYED IN THE INSTRUMENT CLUSTER INFORMATION DISPLAY WHILE DRIVING. B. THE MASTER WARNING LIGHT WILL BE ILLUMINATED.C. DTC P1794:00 (CAPACITOR (I-ELOOP) SYSTEM: CAPACITOR (I-ELOOP) MALFUNCTION) WILL BE STORED IN PCM MEMORY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AN UPDATED VERSION OF THE SOFTWARE FOR THE TOMTOM NAVIGATION SYSTEM HAS BECOME AVAILABLE. UNDER THIS MSP42, THE NAVIGATION SYSTEM WILL BE REFLASHED TO THE UPDATED VERSION USING A SD CARD. THIS SOFTWARE UPDATE WILL ELIMINATE CANCELING VOICE RECOGNITION WHEN VEHICLE SPEED TRANSITIONS PAST 4MPH AND IMPROVE THE FOLLOWING: SYSTEM STABILITY SPEECH RECOGNITION VERBAL AND VISUAL INSTRUCTIONS FOR ROUTE GUIDANCE (3D VIEW NOW INCLUDES MORE VISUAL FEEDBACK SUCH AS ARROWS INDICATING WHICH LANE TO USE IN COMPLICATED INTERCHANGES) COMMANDER SWITCH CONTROL (FOR VEHICLES EQUIPPED) GPS RECOVERY AFTER SIGNAL IS LOST (TUNNELS, PARKING GARAGES, ETC.) CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. OTHERWISE, PERSONAL SETTINGS (SUCH AS DISPLAY AND SOUND ADJUSTMENTS) WILL BE LOST, INCLUDING FAVORITES INFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AN UPDATED VERSION OF THE SOFTWARE FOR THE TOMTOM NAVIGATION SYSTEM HAS BECOME AVAILABLE. UNDER THIS MSP42, THE NAVIGATION SYSTEM WILL BE REFLASHED TO THE UPDATED VERSION USING A SD CARD. THIS SOFTWARE UPDATE WILL ELIMINATE CANCELING VOICE RECOGNITION WHEN VEHICLE SPEED TRANSITIONS PAST 4MPH AND IMPROVE THE FOLLOWING: SYSTEM STABILITY SPEECH RECOGNITION VERBAL AND VISUAL INSTRUCTIONS FOR ROUTE GUIDANCE (3D VIEW NOW INCLUDES MORE VISUAL FEEDBACK SUCH AS ARROWS INDICATING WHICH LANE TO USE IN COMPLICATED INTERCHANGES) COMMANDER SWITCH CONTROL (FOR VEHICLES EQUIPPED) GPS RECOVERY AFTER SIGNAL IS LOST (TUNNELS, PARKING GARAGES, ETC.) CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. OTHERWISE, PERSONAL SETTINGS (SUCH AS DISPLAY AND SOUND ADJUSTMENTS) WILL BE LOST, INCLUDING FAVORITES INFORMATION.