Original record summaries, dates and identifiers for this model-year. Records 301–400 of 503, ordered newest first. Dated records on this page: Feb 14, 2014–Nov 3, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Nov 3, 2015Service Bulletin/Repair Instructions
01-023-15-3084A
NHTSA communication ID: 10105634
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. P0015:00 - EXHAUST CMP TIMING OVER-RETARDED P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. NOTE: IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. P0015:00 - EXHAUST CMP TIMING OVER-RETARDED P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES USING AN AUXILIARY HEATER (BLOCK HEATER) MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0116:00 OR P011A WHEN STARTING IN COLD WEATHER BELOW 32 °F (0 °C). P0116:00: ECT SENSOR NO.1 CIRCUIT RANGE/PERFORMANCE PROBLEM P011A:00: ECT SENSOR NO.1/NO.2 PERFORMANCE PROBLEM THIS IS CAUSED BY ERROR DETECTION LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0300:00, P0301:00, P0302:00, P0303:00 AND/OR P0304:00 STORED IN MEMORY. P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTED CARBON MAY BE DEPOSITED AROUND THE INTAKE VALVES, RESULTING IN UNSTABLE ENGINE COMBUSTION AND MISFIRING DURING THE ACCELERATED WARM-UP SYSTEM (AWS) OPERATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN ONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. C. IPOD ERROR MESSAGE FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6. THESE CONCERNS MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MAZDA INFOTAINMENT SYSTEMS REQUIRE CONTACTING THE PROPER SOURCE FOR DIAGNOSTIC SUPPORT, PARTS AUTHORIZATION, AND PARTS EXCHANGE. SOME COMPONENTS REQUIRE PRIOR AUTHORIZATION BEFORE ORDERING AS EXCHANGE. REFER TO DAG EXCHANGE CENTRAL (MXCONNECT>PARTS AND ACCESSORIES>PARTS>PROGRAMS>EXCHANGE CENTRAL) FOR COMPONENT AVAILABILITY, SOURCE OF TECHNICAL SUPPORT AND PRIOR AUTHORIZATION REQUIREMENT. NOTE: ALWAYS CHECK FOR A TSB THAT MAY MODIFY OR ELIMINATE PRIOR AUTHORIZATION FOR A SPECIFIC SYMPTOM FOR A GIVEN COMPONENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THE NAVIGATION SYSTEM SUPPORT FOR DIAGNOSTICS, PARTS AUTHORIZATION, AND PARTS EXCHANGE REQUIRE CONTACTING THE PROPER SOURCE. TOMTOM NAVIGATION HELP DESK AT 866-486-6866 FROM 7AM-11PM (M-F) AND 9AM-8PM (SAT) EASTERN STANDARD TIME. NOTE: ONE OF THE FIRST STEPS FOR TROUBLESHOOTING THE NAVIGATION SYSTEM IS FOR THE CUSTOMER OR DEALER TO CALL TOMTOM. IF THE TOMTOM CALL CENTER CANNOT SOLVE THE CUSTOMERS PROBLEM, THEY WILL PROVIDE A CASE NUMBER TO THE CUSTOMER THAT CAN BE REFERRED TO IF NEEDED. SERVICE ADVISORS SHOULD GET THIS CASE NUMBER FROM THE CUSTOMER IF THE VEHICLE COMES INTO THE DEALER FOR FURTHER DIAGNOSIS SO THE TECHNICIAN CAN HAVE IT WHEN CALLING TOMTOM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES USING AN AUXILIARY HEATER (BLOCK HEATER) MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0116:00 OR P011A WHEN STARTING IN COLD WEATHER BELOW 32 °F (0 °C). P0116:00: ECT SENSOR NO.1 CIRCUIT RANGE/PERFORMANCE PROBLEM P011A:00: ECT SENSOR NO.1/NO.2 PERFORMANCE PROBLEM. THIS IS CAUSED BY ERROR DETECTION LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE FUEL TANK IS DIFFICULT TO FILL UP. THIS CONCERN MAY BE CAUSED BY IMPROPER OPERATION OF THE NON-RETURN VALVE IN THE FUEL TANK (TEMPORARILY STUCK OPEN). THE PRODUCTION PROCESS OF THE FUEL TANK HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FREQUENT ENGINE STARTS UNDER EXTREMELY COLD AMBIENT TEMPERATURES MAY RESULT IN OIL SEEPAGE FROM THE ENGINE OIL PRESSURE SWITCH. THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. TO CORRECT THE PROBLEM, THE OIL PRESSURE SWITCH HAS BEEN IMPROVED TO INCREASE THE DURABILITY IN COLD AMBIENT TEMPERATURES. ALL SKYACTIV ENGINES EQUIPPED WITH OIL PRESSURE SWITCH PART NUMBER PE01-18-501A ARE APPLICABLE TO THIS ISSUE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0300:00, P0301:00, P0302:00, P0303:00 AND/OR P0304:00 STORED IN MEMORY AND ACCOMPANIED WITH AN INCREASED ENGINE OIL LEVEL. P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTED THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. IN COLD WEATHER BELOW 14 °F (-10 °C) WITH REPEATED SHORT TIME OPERATION, EXCESS FUEL INJECTED IN THE CYLINDERS MAY ACCUMULATE IN THE CRANK CASE AND RESULT IN INCREASED OIL LEVEL AND MISFIRE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN OF A CHECK ENGINE LIGHT AND A/T WARNING LIGHT ON WHEN STARTING THE ENGINE. AT THE SAME TIME, AN ENGINE INSPECTION REQUIRED MESSAGE IS DISPLAYED ON THE LCD. DTC P0722:00 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM) MEMORY. DTC P0722:00 (OPEN CIRCUIT IN OUTPUT SPEED SHAFT CIRCUIT) THE TCM CONTROL LOGIC HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT THE CHECK ENGINE LIGHT ON WITH DTC P0456 STORED IN THE PCM MEMORY. P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY CLOSED AFTER FUELING THE VEHICLE. THIS CAUSES A SMALL FUEL VAPOR LEAK AND TURNS DTC P0456 ON.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN OF A CHECK ENGINE LIGHT AND A/T WARNING LIGHT ON WHEN STARTING THE ENGINE. AT THE SAME TIME, AN ENGINE INSPECTION REQUIRED MESSAGE IS DISPLAYED ON THE LCD. DTC P0722:00 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM) MEMORY. DTC P0722:00 (OPEN CIRCUIT IN OUTPUT SPEED SHAFT CIRCUIT) THE TCM CONTROL LOGIC HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A RATTLING NOISE FROM INSIDE THE FRONT DOOR WHEN THE DOOR VIBRATES WHILE DRIVING OR WHEN THE AUDIO SYSTEM BASS IS TURNED UP. THIS IS CAUSED BY A WORN PAD (A) ON THE WINDOW REGULATOR CABLE FROM REPEATED OPERATION OF THE WINDOW GLASS (B) GOING UP AND DOWN. THE CABLE THEN DIRECTLY CONTACTS THE WINDOW GLASS WHEN RECEIVING VIBRATIONS, CAUSING A RATTLING NOISE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN OF A CHECK ENGINE LIGHT AND A/T WARNING LIGHT ON WHEN STARTING THE ENGINE. AT THE SAME TIME, AN ENGINE INSPECTION REQUIRED MESSAGE IS DISPLAYED ON THE LCD. DTC P0722:00 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM) MEMORY. DTC P0722:00 (OPEN CIRCUIT IN OUTPUT SPEED SHAFT CIRCUIT) THE TCM CONTROL LOGIC HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN OF A WHINING NOISE FROM THE AUTOMATIC TRANSAXLE WHEN DRIVING AT 10 MPH AND ABOVE. THE NOISE: DEPENDS ON THE VEHICLES SPEED ONLY (THE MORE SPEED, THE MORE NOISE) OCCURS WITH ALL TYPES OF DRIVING (ACCELERATION, DECELERATION, STEADY SPEED) DOES NOT DEPEND ON RPM, GEAR, OR ATF TEMPERATURE THIS IS CAUSED BY A DAMAGED BEARING IN THE TRANSAXLE DUE TO IMPROPER CONFIGURATION OF THE TRANSAXLE CASE. A MODIFICATION HAS NOW BEEN IMPLEMENTED ON AUTOMATIC TRANSAXLES WITH THE SERIAL NUMBER 3TR1111680 AND HIGHER OR 3TD1104906 AND HIGHER. THE SERIAL NUMBER CAN BE FOUND ON TOP OF THE TRANSAXLE CASE NEAR THE MANUAL SHAFT LEVER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0191:00 OR DTC P0088:00 STORED IN MEMORY. DTC P0191:00: FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE PROBLEM (EXCEPT 2014 MAZDA3) DTC P0088:00: FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE PROBLEM (2014 MAZDA3) THIS IS CAUSED BY THE HIGH PRESSURE FUEL PUMP NOT GENERATING THE TARGET FUEL PRESSURE (DUE TO A MANUFACTURING ERROR OF THE INNER PARTS). TO CORRECT THE PROBLEM, PRODUCTION CONTROL HAS BEEN IMPROVED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0300:00, P0301:00, P0302:00, P0303:00 AND/OR P0304:00 STORED IN MEMORY AND ACCOMPANIED WITH AN INCREASED ENGINE OIL LEVEL. P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTED THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. IN COLD WEATHER BELOW 14 °F (-10 °C) WITH REPEATED SHORT TIME OPERATION, EXCESS FUEL INJECTED IN THE CYLINDERS MAY ACCUMULATE IN THE CRANK CASE AND RESULT IN INCREASED OIL LEVEL AND MISFIRE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN OF A CHECK ENGINE LIGHT AND A/T WARNING LIGHT ON WHEN STARTING THE ENGINE. AT THE SAME TIME, AN ENGINE INSPECTION REQUIRED MESSAGE IS DISPLAYED ON THE LCD. DTC P0722:00 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM) MEMORY. DTC P0722:00 (OPEN CIRCUIT IN OUTPUT SPEED SHAFT CIRCUIT) THE TCM CONTROL LOGIC HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE EFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. C. IPOD ERROR MESSAGE FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6. THESE CONCERNS MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. THESE CONCERN MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME. THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDSFREE MODULE WILL NOT ADDRESS THE IPOD ERROR MESSAGE CONCERN FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6 AT THIS TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
USE THE FOLLOWING REPAIR PROCEDURE TO MINIMIZE THE NEED TO REPLACE THE CATALYST CONVERTER/EXHAUST PIPE WHEN REMOVING OXYGEN SENSORS AND/OR AIR FUEL RATIO SENSORS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. THESE CONCERN MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR. SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) THIS IS CAUSED BY A FAILURE OF THE RELATED CLUTCH HUB(S). TO CORRECT THE PROBLEM OF HARD SHIFTING, THE SHAPE OF THE 3-4 AND 5-6 CLUTCH HUB HAS BEEN CHANGED. A SURFACE TREATMENT HAS NOW BEEN ADDED TO THE 3-4 CLUTCH HUB TO PREVENT 3RD GEAR FROM JUMPING OUT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES EQUIPPED WITH SKYACTIV-G 2.0L ENGINE MAY EXPERIENCE ENGINE OIL SEEPAGE FROM DRAIN PLUG AFTER THE ENGINE OIL IS REPLACED EVEN IF THE PLUG IS TIGHTENED TO THE SPECIFIED TORQUE WITH A NEW GASKET. OIL PAN DRAIN PLUG TIGHTENING TORQUE: 3041 N·M {3.14.1 KGF·M, 2330 FT·LBF} SEATING SURFACE OF THE OIL PAN FOR THE DRAIN PLUG MAY HAVE POOR FLATNESS DUE TO IMPROPER SPOT WELDING AND/OR THE SURFACE MAY HAVE GOTTEN A SCRATCH DURING MANUFACTURING PROCESS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL ON WITH DTC P0780 AND/OR P1738 OR OTHER DTCS, BULLETIN NOTETHIS BULLETIN HAS BEEN REPLACED BY SERVICE BULLETIN 05-005/14.THIS BULLETIN SUPERSEDES THE PREVIOUS BULLETINS 05-003/14 ISSUED ON 04/04/14 AND 02/21/14 AND 05-005/13 ISSUED ON 09/23/13, 9/25/13,12/16/13, AND 12/17/13
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A CREAKING NOISE FROM UNDER THE FRONT OF THE VEHICLE WHEN DRIVING OVER BUMPS. THE NOISE OCCURS AT APPROX. 12 - 25 MPH (20 - 40 KM/H) WHEN THE ROAD SURFACE IS WET OR AFTER A CAR WASH. THE NOISE BECOMES MORE NOTICEABLE WHEN DRIVING OVER HIGHER BUMPS. THE CREAKING NOISE IS CAUSED WHEN THE FRONT LOWER CONTROL ARM BUSHING(S) (A) BECOME WET.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0300:00, P0301:00, P0302:00, P0303:00 AND/OR P0304:00 STORED IN MEMORY AND ACCOMPANIED WITH AN INCREASED ENGINE OIL LEVEL.P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTEDTHIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. IN COLD WEATHER BELOW 14 °F (-10 °C) WITH REPEATED SHORT TIME OPERATION, EXCESS FUEL INJECTED IN THE CYLINDERS MAY ACCUMULATE IN THE CRANK CASE AND RESULT IN INCREASED OIL LEVEL AND MISFIRE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR. SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) THIS IS CAUSED BY A FAILURE OF THE RELATED CLUTCH HUB(S). TO CORRECT THE PROBLEM OF HARD SHIFTING, THE SHAPE OF THE 3-4 AND 5-6 CLUTCH HUB HAS BEEN CHANGED. A SURFACE TREATMENT HAS NOW BEEN ADDED TO THE 3-4 CLUTCH HUB TO PREVENT 3RD GEAR FROM JUMPING OUT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN DEALING WITH CUSTOMER COMPLAINTS OF EXCESSIVE CONDENSATION AND/OR WATER WITHIN THE HEADLAMP UNIT, FIRST DETERMINE IF ALL THE BULB SOCKETS ARE PRESENT AND CORRECTLY INSTALLED. IN MOST CASES YOU WILL FIND THAT THE BULB SEAL NO. 1 (A) OR HID BULB SEAL NO. 1 (B) AND BULB SEAL NO. 2 (C) SOCKET COVERS HAVE NOT BEEN CORRECTLY INSTALLED OR ARE MISSING DUE TO IMPROPER PRIOR REPAIRS (I.E., CUSTOMER REPLACING THE HEADLAMP BULBS OR BODY SHOP NOT TRANSFERRING THEM WHEN REPLACING THE HEADLAMP UNIT(S) DUE TO A COLLISION). ANY DAMAGE CAUSED BY MISSING SOCKET COVERS, HID MODULE SEAL (D), OR MISSING BUMPER BRACKETS (E) IS NOT COVERED BY WARRANTY POLICY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.854 OR LATER).NAVIGATION SYSTEM FREEZES.MESSAGE WAITING FOR VALID GPS SIGNAL IS SHOWN IN THE MENU BAR OF NAVIGATION DISPLAY FOR SEVERAL MINUTES.VEHICLE SYMBOL IS OFF ROAD WHILE DRIVING / WRONG POSITION OF VEHICLE ON MAP.MAP IS ROTATING WHEN VEHICLE IS PARKED OR WHILE DRIVING.NAVIGATION SCREEN DONT APPEAR AFTER DEPRESSING NAVIGATION BUTTON. THEN IT DOES NOT RECOVER BY OPERATING ACC OFF TO ON POSITION.UNEXPECTED STOPPING VOICE CONTROL MESSAGE, USUALLY WHEN STARTING THE VEHICLE.CURRENT CAR POSITION (CCP) TURNING 180 DEGREES WHEN DRIVING IN REVERSE.THE MESSAGE WAITING FOR A VALID GPS SIGNAL APPEARS.RED SCREEN WITH MESSAGE "PROBLEM WITH MAP".YELLOW SCREEN WITH MESSAGE "INSERT SD CARD".NO MAP FOUND ERROR AND SD CARD CONTAINS A MAP.SCREEN TEMPORARILY GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) FOR 2 MINUTES DURING STARTUP. AFTERWARDS, THE NAVIGATION WILL NOT START UNTIL THE IGNITION IS CYCLED.SCREEN GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) DURING STARTUP.SCREEN LOCKS UP TO A "BLACK SCREEN.VEHICLE ICON JUMPS AROUND OR VIBRATES.IF NAVIGATION BUTTON IS PRESSED DURING AUDIO SCREEN, THE SCREEN FREEZES AND THE TOUCH SCREEN BECOMES INOPERATIVE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE STEERING WHEEL IS OFF CENTER MORE THAN 3° EVEN WHEN DRIVING STRAIGHT ON A FLAT ROAD. FOLLOW STEERING WHEEL ALIGNMENT PROCEDURE.
Source components: STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.854 OR LATER).NAVIGATION SYSTEM FREEZES.MESSAGE WAITING FOR VALID GPS SIGNAL IS SHOWN IN THE MENU BAR OF NAVIGATION DISPLAY FOR SEVERAL MINUTES.VEHICLE SYMBOL IS OFF ROAD WHILE DRIVING / WRONG POSITION OF VEHICLE ON MAP.MAP IS ROTATING WHEN VEHICLE IS PARKED OR WHILE DRIVING.NAVIGATION SCREEN DONT APPEAR AFTER DEPRESSING NAVIGATION BUTTON. THEN IT DOES NOT RECOVER BY OPERATING ACC OFF TO ON POSITION.UNEXPECTED STOPPING VOICE CONTROL MESSAGE, USUALLY WHEN STARTING THE VEHICLE.CURRENT CAR POSITION (CCP) TURNING 180 DEGREES WHEN DRIVING IN REVERSE.THE MESSAGE WAITING FOR A VALID GPS SIGNAL APPEARS.RED SCREEN WITH MESSAGE "PROBLEM WITH MAP".YELLOW SCREEN WITH MESSAGE "INSERT SD CARD".NO MAP FOUND ERROR AND SD CARD CONTAINS A MAP.SCREEN TEMPORARILY GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) FOR 2 MINUTES DURING STARTUP. AFTERWARDS, THE NAVIGATION WILL NOT START UNTIL THE IGNITION IS CYCLED.SCREEN GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) DURING STARTUP.SCREEN LOCKS UP TO A "BLACK SCREEN.VEHICLE ICON JUMPS AROUND OR VIBRATES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IN SUPPORT OF SKYACTIV MANUAL TRANSMISSION MODELS, MAZDA WILL SHIP TO ALL DEALERS ONE (1) NEW SPECIAL SER-VICE TOOL (SST). THE SST WILL BE SHIPPED AUTOMATICALLY BY MAZDAS TOOL VENDOR SNAP-ON TOOLS, STARTING IN MID-OCTOBER 2014.THE FOLLOWING SST IS THE LATEST ADDITION TO THE MAZDA REQUIRED TOOL (MRT) LIST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT BLUETOOTH® HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THE HANDLING OF BLUETOOTH® HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT EITHER OF THE FOLLOWING CONCERNS:A.THE DASHBOARD UPPER PANEL IS STICKY. B.THE DASHBOARD UPPER PANEL JUST ABOVE THE INFORMATION DISPLAY (A) IS WARPING, GENERATING A GAP (B).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY.P0015:00 - EXHAUST CMP TIMING OVER-RETARDEDP0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A CRACKING NOISE ORIGINATED AT THE POSITIONING PINS NEAR THE TOP CORNERS OF THE WIND-SHIELD AND/OR REAR WINDOW WHEN DRIVING ON UNEVEN ROAD SURFACE. THIS HAPPENS WHEN THE AMBIENT TEMPERATURE IS APPROXIMATELY 14 °F (-10 °C) OR LOWER AND THE VEHICLE CABIN HAS NOT YET WARMED UP. THE NOISE IS CAUSED BY THE WINDSHIELD AND/OR REAR WINDOW LOCATING STOPPER CONTACTING THE PANEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IN ACCORDANCE WITH FEDERAL REGULATIONS, FOLLOW THE PROCEDURE LISTED BELOW WHEN REPLACING A SPEEDOMETER.NOTE:MAZDA VEHICLES ARE MANUFACTURED WITH TAMPER-PROOF SPEEDOMETERS.WHEN A SPEEDOMETER IS REPLACED, THE NEW SPEEDOMETER WILL READ ZERO (0) MILES.THIS PROCEDURE IS EXTREMELY IMPORTANT TO ACCURATELY REPRESENT ACTUAL VEHICLE MILEAGE.PRIOR TO SPEEDOMETER REMOVAL, COMPLETE THE INFORMATION REQUIRED ON THE SPEEDOMETER REPLACE-MENT LABEL. LABELS CAN ONLY BE ORDERED THROUGH MSTORE, NOT MDCS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT AN UNUSUAL (CLACKING) NOISE FROM UNDER THE FRONT OF THE VEHICLE. THIS NOISE ONLY OCCURS WHEN STARTING TO MOVE THE VEHICLE WHILE THE STEERING WHEEL IS TURNED TO THE FULL LEFT POSITION. NOTE:THE NOISE WILL NOT OCCUR IF THE STEERING WHEEL IS IN THE CENTER OR FULL RIGHT POSITION.THE NOISE IS CAUSED WHEN THE EDGE OF THE LEFT SIDE INNER BALL JOINT (A) GETS STUCK WITH THE STEERING GEAR HOUSING. THE FOLLOWING MODIFICATIONS HAVE BEEN MADE TO ELIMINATE THE NOISE:1. THE SHAPE OF THE INNER BALL JOINT EDGE HAS BEEN CHANGED.2. GREASE HAS BEEN APPLIED TO THE INNER BALL JOINT EDGE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS:HARD TO SHIFT INTO 3RD GEARSOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H)THIS IS CAUSED BY THE FRICTION COEFFICIENT BETWEEN THE 3/4 CLUTCH HUB AND THE SLEEVE INCREASING. A SURFACE TREAT-MENT HAS NOW BEEN ADDED TO THE 3/4 CLUTCH HUB TO DECREASE THE FRICTION COEFFICIENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT THE CHECK ENGINE LIGHT ON WITH DTC P0456 STORED IN THE PCM MEMORY. P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY CLOSED AFTER FUELING THE VEHICLE. THIS CAUSES A SMALL FUEL VAPOR LEAK AND TURNS DTC P0456 ON.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS SERVICE BULLETIN PROVIDES INFORMATION REGARDING THE PROPER USE OF THE DRIVERS FLOOR MAT TO AVOID ANY POTENTIAL INTERFERENCE WITH THE FOOT PEDALS. THE FOLLOWING ARE POSSIBLE CAUSES OF FLOOR MAT INTERFERENCE, WHICH CAN BE AVOIDED WITH PROPER USAGE. FLOOR MAT MOVES FORWARD DUE TO IMPROPER INSTALLATION. INAPPROPRIATE FLOOR MAT (SUCH AS AFTERMARKET, NON-FACTORY-EQUIPPED, OR NON-GENUINE) IS USED. FLOOR MAT IS STACKED ONE ON TOP OF ANOTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MAZDA NORTH AMERICAN OPERATIONS RECEIVED MANY REQUESTS FROM OUR DEALERS ASKING US TO APPROVE ADDITIONAL ON-CAR BRAKE LATHES AS AN OPTION FOR MNAO AUTHORIZED EQUIPMENT. DUE TO YOUR FEEDBACK AND AFTER EVALUATING A FEW ON-CAR BRAKE LATHES, WE ARE PLEASED TO ANNOUNCE THAT WE HAVE ADDED THE PRO CUT ON-CAR BRAKE LATHE TO MNAO AUTHORIZED EQUIPMENT PROGRAM. THE ACCU-TURN IS STILL AN APPROVED BRAKE LATHE BUT IT IS NO LONGER AVAILABLE FOR PURCHASE FROM OUR VENDOR. IMPORTANT REMINDER ROTORS MUST BE MACHINED USING A MAZDA APPROVED ON-CAR BRAKE LATHE OR WARRANTY CLAIMS ARE SUBJECT TO DENIAL OR DEBIT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE AMBIENT TEMPERATURE DISPLAY IS NOT ACCURATE, OR IT TAKES TOO LONG FOR THE DISPLAY TO SHOW ACTUAL TEMPERATURE.WHEN YOU ENCOUNTER A CUSTOMER WITH THIS CONCERN, FIRST VERIFY THE CONDITION WHEN THE CUSTOMER NOTICED THIS SYMPTOM. IF THE CONDITION IS SIMILAR TO THE FOLLOWING CONTROL LOGIC OF AMBIENT TEMPERATURE OR DIF-FERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS, ADVISE THE CUSTOMER THAT THIS IS A NOR-MAL CHARACTERISTIC OF THE VEHICLE AND NOT A MALFUNCTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES EXHIBIT BRAKE RELATED CONCERNS SUCH AS BRAKE NOISE, BRAKE JUDDER OR BRAKE DRAGGING. IF YOU ENCOUNTER A CUSTOMER COMPLAINT FOR ANY ONE OF THESE SYMPTOMS, REFER TO THE FOLLOWING INFORMATION TO UNDERSTAND WHY SYMPTOMS MAY OCCUR, AND TO BETTER ASSIST THE CUSTOMER IN RESOLVING THEIR SPECIFIC BRAKE CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN OF A WHINING NOISE FROM THE AUTOMATIC TRANSAXLE WHEN DRIVING AT 10 MPH AND ABOVE. THE NOISE:DEPENDS ON THE VEHICLES SPEED ONLY (THE MORE SPEED, THE MORE NOISE)OCCURS WITH ALL TYPES OF DRIVING (ACCELERATION, DECELERATION, STEADY SPEED)DOES NOT DEPEND ON RPM, GEAR, OR ATF TEMPERATURE
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME NEW VEHICLES MAY EXHIBIT OIL SEEPAGE UNDERNEATH THE BEARING BRACKET (A) ON THE RIGHT SIDE OF THE JOINT SHAFT. THIS IS CAUSED BY THE OIL CONTENT SEPARATING FROM THE GREASE APPLIED TO THE BEARING AND SPLINE SEEPING FROM THE SEAL AND BRACKET.THERE IS NO FUNCTIONAL PROBLEM WITH THIS ISSUE SINCE THE AMOUNT OF OIL SEEPAGE IS VERY SMALL COMPARED TO THE AMOUNT OF GREASE. NOTE THAT THE OIL SEEPAGE WILL STOP WHILE THE VEHICLE IS IN USE.IF YOU ENCOUNTER A CUSTOMER COMPLAINT ABOUT THIS CONCERN, WIPE OFF THE OIL WITH A RAG. DO NOT REPLACE THE JOINT SHAFT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0191:00 OR DTC P0192:00 STORED IN MEMORY. DTC P0191:00: FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE PROBLEM (EXCEPT 2014 MAZDA3) DTC P0192:00: FUEL PRESSURE SENSOR CIRCUIT LOW INPUT (2014 MAZDA3) THIS IS CAUSED BY THE HIGH PRESSURE FUEL PUMP NOT GENERATING THE TARGET FUEL PRESSURE (DUE TO A MANUFACTURING ERROR OF THE INNER PARTS). TO CORRECT THE PROBLEM, PRODUCTION CONTROL HAS BEEN IMPROVED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY.P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONTHE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER.P0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION. NOTE: THIS SERVICE INFORMATION IS ALSO APPLICABLE IF DTC P0780:00 IS STOREED INDEPENDENTLY. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.852 OR LATER). VEHICLE ICON JUMPS AROUND OR VIBRATES. CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. OTHERWISE, PERSONAL SETTINGS (SUCH AS DISPLAY AND SOUND ADJUSTMENTS) WILL BE LOST, INCLUDING FAVORITES INFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY.P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONTHE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER.P0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY.P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONTHE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER.P0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE MIL ON WITH DTC P0191:00 (FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFOR-MANCE PROBLEM) STORED IN MEMORY. THIS IS CAUSED BY THE HIGH PRESSURE FUEL PUMP NOT GENERATING THE TARGET FUEL PRESSURE (DUE TO A MANUFACTURING ERROR OF THE INNER PARTS). TO CORRECT THE PROBLEM, PRODUCTION CONTROL HAS BEEN IMPROVED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MAZDA: DUE TO HIGH PRESSURE FUEL PUMP NOT GENERATING TARGET FUEL PRESSURE, CAUSED BY MANUFACTURING ERROR, THE CHECK ENGINE LIGHT COMES ON. MODEL 2012-2014. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. P0015:00 - EXHAUST CMP TIMING OVER-RETARDED P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.852 OR LATER). VEHICLE ICON JUMPS AROUND OR VIBRATES. CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. OTHERWISE, PERSONAL SETTINGS (SUCH AS DISPLAY AND SOUND ADJUSTMENTS) WILL BE LOST, INCLUDING FAVORITES INFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE MIL ON WITH DTC P0191:00 (FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFOR-MANCE PROBLEM) STORED IN MEMORY. THIS IS CAUSED BY THE HIGH PRESSURE FUEL PUMP NOT GENERATING THE TARGET FUEL PRESSURE (DUE TO A MANUFACTURING ERROR OF THE INNER PARTS). TO CORRECT THE PROBLEM, PRODUCTION CONTROL HAS BEEN IMPROVED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MAZDA: DUE TO DROP IN ENGINE OIL PRESSURE, SOME VEHICLES EXPERIENCE A ROUGH IDLE, CAUSED BY FOREIGN OBJECT(S) STUCK ON OCV OR OIL PUMP PRESSURE RELIEF VALVE. MODEL 2012-2014 MAZDA3, MAZDA6, CX-5. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE MIL ON WITH DTC P0780 (GEAR SHIFTING MALFUNCTION) AND/OR P1738 (AUTO-MATIC TRANSAXLE INTERNAL MALFUNCTION) WITH/WITHOUT U0401, OR OTHER DTCS STORED IN MEMORY.OTHER DTCS (WITH THE ABOVE DTCS) - P0746:00, P0751:00, P0752:00, P0756:00, P0757:00, P0761:00, P0762:00, P0766:00, P0767:00, P0771:00, P0772:00, P079A:00, P0842:00, P0843:00, P0847:00, P0848:00, P0872:00, P0873:00, P0877:00, P0878:00, P1784:00TO CORRECT THE PROBLEM, A NEW PROGRAMMED VALVE BODY HAS BEEN ESTABLISHED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY. P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON THE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER. P0780:00 - GEAR SHIFTING MALFUNCTION P1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY. P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON THE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER. P0780:00 - GEAR SHIFTING MALFUNCTION P1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN OF A WHINING NOISE FROM THE AUTOMATIC TRANSAXLE WHEN DRIVING AT 10 MPH AND ABOVE. THE NOISE: DEPENDS ON THE VEHICLES SPEED ONLY (THE MORE SPEED, THE MORE NOISE) OCCURS WITH ALL TYPES OF DRIVING (ACCELERATION, DECELERATION, STEADY SPEED) DOES NOT DEPEND ON RPM, GEAR, OR ATF TEMPERATURE. THIS IS CAUSED BY A DAMAGED BEARING IN THE TRANSAXLE DUE TO IMPROPER CONFIGURATION OF THE TRANSAXLE CASE. A MODIFICATION HAS NOW BEEN IMPLEMENTED ON AUTOMATIC TRANSAXLES WITH THE SERIAL NUMBER TR1111680 AND HIGHER OR TD1104906 AND HIGHER. THE SERIAL NUMBER CAN BE FOUND ON TOP OF THE TRANSAXLE CASE NEAR THE MANUAL SHAFT LEVER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OF THE FOLLOWING SYMPTOMS WHEN THE VEHICLE IS STOPPED AND THE TRANSMISSION IS IN D RANGE: AN INTERMITTENT HIGH ENGINE IDLE SPEED. AN INTERMITTENT ENGAGEMENT SHOCK. AN INTERMITTENT FORWARD LURCH. THESE CONDITIONS MAY OCCUR WHEN THE CUSTOMER DEPRESSES THE BRAKE PEDAL AND MAKES CONTACT WITH THE THROTTLE PEDAL SIMULTANEOUSLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN OF A WHINING NOISE FROM THE AUTOMATIC TRANSAXLE WHEN DRIVING AT 10 MPH AND ABOVE. THE NOISE: DEPENDS ON THE VEHICLES SPEED ONLY (THE MORE SPEED, THE MORE NOISE) OCCURS WITH ALL TYPES OF DRIVING (ACCELERATION, DECELERATION, STEADY SPEED) DOES NOT DEPEND ON RPM, GEAR, OR ATF TEMPERATURE. THIS IS CAUSED BY A DAMAGED BEARING IN THE TRANSAXLE DUE TO IMPROPER CONFIGURATION OF THE TRANSAXLE CASE. A MODIFICATION HAS NOW BEEN IMPLEMENTED ON AUTOMATIC TRANSAXLES WITH THE SERIAL NUMBER TR1111680 AND HIGHER OR TD1104906 AND HIGHER. THE SERIAL NUMBER CAN BE FOUND ON TOP OF THE TRANSAXLE CASE NEAR THE MANUAL SHAFT LEVER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT RUST ON THE BOTTOM OF THE REAR DOOR GLASS GUIDE (A) FROM CONTACT WITH THE REAR BELTLINE MOLDING (B). THIS IS CAUSED BY A VIBRATION WHILE DRIVING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE MIL ON WITH DTC P0780 (GEAR SHIFTING MALFUNCTION) AND/OR P1738 (AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION) WITH/WITHOUT U0401, OR OTHER DTCS STORED IN MEMORY. OTHER DTCS (WITH THE ABOVE DTCS) - P0746:00, P0751:00, P0752:00, P0756:00, P0757:00, P0761:00, P0762:00, P0766:00, P0767:00, P0771:00, P0772:00, P079A:00, P0842:00, P0843:00, P0847:00, P0848:00, P0872:00, P0873:00, P0877:00, P0878:00, P1784:00 TO CORRECT THE PROBLEM, A NEW PROGRAMMED VALVE BODY HAS BEEN ESTABLISHED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN REPLACING THE SIRIUSXM SATELLITE RADIO UNIT (OR A MAZDA CONNECT TUNER AND AMP UNIT (TAU)) WITH REPLACEMENT TUNER FOR ANY REASON, A CALL MUST BE MADE TO INFORM SIRIUSXM OF THE EXISTING RADIO ID AND THE NEW/ REPLACEMENT SAT RADIO ID AS SOON AS POSSIBLE TO ENSURE THE CUSTOMER LEAVES THE DEALERSHIP WITH ACTIVE (WORKING SAT RADIO.