Original record summaries, dates and identifiers for this model-year. Records 1–100 of 503, ordered newest first. Dated records on this page: Jan 23, 2020–Jul 29, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jul 29, 2026Service Bulletin/Repair Instructions
09-022-26
NHTSA communication ID: 11035599
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. 09-042/04 12/10/04 DESCRIPTION Some vehicles may exhibit inoperative electric rear window defroster grid lines, integral antenna concerns causing radio reception issues or terminal tabs pulled from the rear window glass. Follow the diagnostic and repair procedures included in this service information to inspect and service rear defroster grid lines, integral antenna concerns or broken terminal tabs.
Source components: ELECTRICAL SYSTEM · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Alert supersedes the previously issued SA listed below: The changes are noted in Red. SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owner’s Manual, Workshop Manual, Technical Service Bulletin, etc.).
Source components: ENGINE · POWER TRAIN · SERVICE BRAKES · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern. NOTE: Before following this Service Alert repair procedure, ensure published TSBs in MGSS have been completed per model year.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For improvement of electrical diagnosis, the SKYACTIV® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV® vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When replacing the SiriusXM satellite radio unit, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with an active SAT radio.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about a noisy HVAC blower motor or odor after a cabin air filter replacement. Foreign debris on the blower motor after servicing the cabin air filter may be the cause. During the removal of the cabin air filter, foreign debris (leaves, dust, dirt....ect.) may fall on the blower motor causing a fluttering type noise or odor.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The SKYACTIV-DRIVE FW6A-EL AT uses “Automatic Transmission Fluid (ATF) Type: FZ”. Only use “ATF-FZ” to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For improvement of electrical diagnosis, the SKYACTIV® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV® vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
Source components: ELECTRICAL SYSTEM · ENGINE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the “Speedometer Replacement Label”. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda’s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO’s services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN · SERVICE BRAKES, HYDRAULIC · STEERING · TIRES · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738).
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
When servicing SKYACTIV engine vehicles requiring to replace the Oil Galley Plug and Crush Washer, order the required part numbers below. These parts are not listed in GEPC and were previously listed as "non-serviceable" in the cylinder block diagram.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Cell phone charger/accessory in 12V socket (engine no start or unable to turn off) 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple CarplayâÃÂâ/ Android AutoâÃÂâ will not connect) 6. Over-sized wheels/tires (incorrect GPS location)
NHTSA source summary · Original PDF not reviewed by Recallfolio
The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
Source components: POWER TRAIN · SUSPENSION:FRONT:WHEEL BEARING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN · SERVICE BRAKES, HYDRAULIC · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Battery Maintenance: This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Automatic Transmission/Transaxle Cooler and Lines Flushing Procedure: Automatic Transaxle/Transmission (A/T) oil cooler and lines must be power flushed completely before an overhauled or replacement A/T is installed (except SKYACTIV-DRIVE). The most common cause of repeat A/T failures is lack of lubrication to the front and rear planetary gears. This is usually caused by an accumulation of metal particles and debris (from a previous A/T failure) on the internal mesh type baffle of the oil cooler. Power flushing will remove the restriction by back flushing, followed by forward flushing to dislodge a restriction, then back flushing again. This will in turn ensure full ATF flow for the transmission when it is operating.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For improvement of electrical diagnosis, the SKYACTIVî Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIVî vehicles and compare suspect terminal drag with a good know terminal.To measure the voltage/resistance avoiding any terminal damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. E85: A blend of 85% ethanol and 15% gasoline All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary:
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline, E85: A blend of 85% ethanol and 15% gasoline, All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V. What if a customer puts E85 in there Mazda vehicle? Symptoms include: Rough Running, Lean Codes, Misfires and/or misfire codes, Lack of power, Poor fuel economy, Spark knock, Mechanical engine damage.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on, P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on, P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on, P0780:00 - Gear shifting malfunction, P1738:00 Automatic transaxle internal malfunction. This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This service bulletin provides information regarding the proper use of the driverâÂÂs floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAVIGATION UPDATES FOR TOMTOM NAVIGATION SYSTEM. Some customers may request updates for their vehicle's navigation system. Refer customers to Mazdausa.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Accessory instructions can be found on OneMazda under Dealer Resources - Parts & Accessories. The links provided below can be used for quick access: For 2016 models and newer: NOTE: Instructions are found under the "Attachments" section once a part is selected. Accessories E-catalog For models prior to 2016: Accessory Parts and Installation Instructions
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience exterior trim heat damage when parked near a glass building. This may be caused by the suns reflection. If a building creates enough of a curve with a series of flat windows, which act like mirrors, the reflections all converge at one point, focusing and concentrating the light onto the street below.
Source components: VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When programming a key or installing a Genuine Mazda Accessory Remote Engine Start system, you may encounter programming difficulty. This may be caused by a customer installed aftermarket decorative trim and/or cover on the START/STOP ENGINE button. The aftermarket accessory may create electrical interference, which may interfere with programming.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Subject: ** UPDATE** - Takata Inflator Special Service Program (Extended Warranty) Special Service Program SSPB3: In December 2017 Special Service Program SSPB3 - Takata Inflator Extended Warranty was announced. The extended warranty was a result of the Takata airbag inflator class action settlement. Mazda will provide supplemental warranty coverage for all repairs and replacements (including parts and labor) to correct any defects in the materials or workmanship of Takata airbag inflators and the replacement inflators installed pursuant to the Takata airbag recalls. The program covers defects in the Inflator only and does not cover other items in the airbag system. Additionally, the program also does not cover airbags that have properly deployed as a result of a collision.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Mazda DCA-8000PM is required for all warranty battery testing. If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. âÂÂMazda Air Cooling Coil Coatingâ is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN · STEERING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTHî hands-free unit or text messaging related concerns. To improve the handling of BLUETOOTHî hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Record the vehicle mileage. 2. Engine at normal operating temperature, top off engine oil level to the full mark on the dipstick. 3. Ask the customer to return to the dealer after 1200 miles to recheck the engine oil level. 4. After 1200 miles, engine at normal operating temperature, check the engine oil level on the dipstick. 5. Is the engine oil level above the low mark on the dipstick? ïÃÂ÷ Yes - No repair is necessary. ïÃÂ÷ No - Proceed to MGSS online or Workshop Manual (section 01-03 NO. 16 HIGH OIL CONSUMPTION/LEAKAGE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. The noise: ï· Depends on the vehicleâÂÂs speed only (the more speed, the more noise) ï· Occurs with all types of driving (acceleration, deceleration, steady speed) ï· Does not depend on rpm, gear, or ATF temperature
NHTSA source summary · Original PDF not reviewed by Recallfolio
Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. The following 3 adhesives are alternatives available as an equivalent to Loctite 962T: Loctite 272, Loctite 518 Threebond TB-1386H
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSP99 - 2010 MAZDA3 - DASHBOARD UPPER PANEL STICKY SURFACE: For certain 2010 Mazda3 vehicles, the warranty coverage for dashboard replacement for sticky surface condition only is extended to 10 years (120 months) from the original Warranty Start Date, with no mileage limitations. Any other condition for dashboard replacement, such as discoloration, warp, or material splitting, is covered only for 36 months or 36,000 miles, whichever comes first. SSPA9 - 2010-2013 MAZDA3 - GAP BETWEEN INSTRUMENT PANEL AND INFORMATION DISPLAY WARRANTY EXTENSION PROGRAM: On certain 2010-2013 Mazda3 vehicles, the instrument panel just above the information display may be warping, generating a gap between the instrument panel and information display, if exposed to heat under high ambient temperature. The warranty coverage for instrument panel replacement due to warping or a gap is extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date or April 30, 2018 whichever is later, with no mileage limitation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about an unusual noise coming from the engine compartment for about 20 seconds after a cold engine start. This noise is a normal engine operation for improved exhaust gas emissions. The noise does not indicate a malfunction. ACCELERATED WARM-UP SYSTEM (AWS): All SKYACTIV-G engines adopt AWS to reduce exhaust gas emissions immediately after a cold engine start. AWS increases the engine idling speed and retards the ignition timing for about 20 seconds after the cold engine start to quickly warm up the catalytic converter. The customer may identify the engine sound during the AWS operation as a unusual noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010.
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit one of the following concerns: ï· Sometimes the shifter may jump out of 3rd gear over a road bump when accelerating after deceleration at 25-40 mph (40-65 km/h) ï· Hard to shift into 3rd, 4th, 5th, and/or 6th gear ï· Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When replacing manual or automatic transmission, make sure to remove the plug from the old transmission (as shown below) and then re-install it to the new transmission with a new washer. The new transmissions (including remanufactured A/T) have a shipping plug, as shown in the figures (M/T: black, rubber made; A/T: pink and black, with breather). This plug is for shipping use only and needs to be removed in order to re-install the original plug from the old transmission.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The ownerâÂÂs manual contains procedures and precautions for the maintenance and cleaning of plastic parts, like the brand emblem. However, it is still important to remind customers about these precautions. Customers should never use inadequate, harsh or aggressive cleaning products on plastic parts. CAUTION: Be aware that when cleaning the brand emblem, never use cleaning products that are highly acidic/alkaline detergent, organic solvents or those with aggressive chemical products, otherwise, the brand emblem may become cracked and/or deformed (as shown in the example below). Always refer customers to the ownerâÂÂs manual for proper cleaning using cold or lukewarm water and a mild, neutral detergent.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. NOTE: The following Caution is included with every ATX that requires configuration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the steering wheel is off center more than 3ð even when driving straight on a flat road. Customers having this concern should have their vehicle repaired using the following repair procedure.