Original record summaries, dates and identifiers for this model-year. Records 101–200 of 282, ordered newest first. Dated records on this page: Sep 13, 2023–Nov 5, 2024.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Nov 5, 2024Service Bulletin/Repair Instructions
01-005-24c
NHTSA communication ID: 11011133
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the headlights get foggy or have water spots inside. This concern may be caused by the anti-fog coating not preventing inner condensation under certain situations. To eliminate this concern, the anti-fog coating performance was improved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the fail-safe thermostat in the coolant control valve on certain CX-5, Mazda3, CX-3, Mazda6 and CX-30 vehicles that are equipped with the suspected coolant control valve. The warranty coverage for a specific repair of fail-safe thermostat has been extended to 15 years (180 months) /150,000 miles (240,000 km) whichever comes first, from the original warranty start date. Concern Outline: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: Engine takes longer to warm up, Engine temperature gauge fluctuates, Low coolant temperature indicator (blue) light stays on longer or turns on while driving, Poor heater performance, especially at idle. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement under this SSP to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures. If a customer arrives at your dealership with the concern described, please repair under this Special Service Program.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) to extend the warranty coverage for a specific repair of the fail-safe thermostat in the coolant control valve on certain CX-5, Mazda3, CX-3, Mazda6 and CX-30 vehicles that are equipped with the suspected coolant control valve. The warranty coverage for a specific repair of fail-safe thermostat has been extended to 15 years (180 months) /150,000 miles (240,000 km) whichever comes first, from the original warranty start date. Concern Outline: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: Engine takes longer to warm up, Engine temperature gauge fluctuates, Low coolant temperature indicator (blue) light stays on longer or turns on while driving, Poor heater performance, especially at idle. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement under this SSP to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures. If a customer arrives at your dealership with the concern described, please repair under this Special Service Program.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).
NHTSA source summary · Original PDF not reviewed by Recallfolio
The SKYACTIV-DRIVE FW6A-EL AT uses “Automatic Transmission Fluid (ATF) Type: FZ”. Only use “ATF-FZ” to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of a shift shock when shifting from 2nd to 3rd when the engine is cold. This is caused by improper TCM control logic. To eliminate this concern, the TCM control logic has been modified. NOTE: If the calibration file of the concerned vehicle is not found in the Calibration Files Information below, this Service Information is not applicable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the power liftgate (PLG) may open unintentionally while the vehicle is parked or stopped. Due to the shape of the 7th generation remote transmitter, the power liftgate button may be long pressed unintentionally in a pocket or a bag. To eliminate this concern, the keyless control specification has been modified. The button press time has been increased from 0.5 seconds to 1 second.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This service information provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of a shift shock when shifting from 2nd to 3rd when the engine is cold. This is caused by improper TCM control logic. To eliminate this concern, the TCM control logic has been modified. NOTE: If the calibration file of the concerned vehicle is not found in the Calibration Files Information below, this Service Information is not applicable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of a shift shock when shifting from 2nd to 3rd when the engine is cold. This is caused by improper TCM control logic. To eliminate this concern, the TCM control logic has been modified. NOTE: If the calibration file of the concerned vehicle is not found in the Calibration Files Information below, this Service Information is not applicable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. Hotline and MASH authorization is not required to order parts for performing this repair. If there are any questions on part ordering or part status, contact the Dealer Assistance Group.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a “Telematics Malfunction” message in the instrument cluster with DTC U3000:00-TCU (Emergency call unit/telematics communication unit internal malfunction) or U3000:04-TCU (Telematics communication unit internal malfunction) stored in memory. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a Connected Vehicle failure. The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control
Source components: ELECTRICAL SYSTEM · ENGINE · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For improvement of electrical diagnosis, the SKYACTIV® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV® vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Before judging a steering wheel as having premature wear or a defect, first clean the steering wheel as explained in the repair information. Some vehicles may have steering wheel stains caused by chemicals such as hand lotions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
Source components: ELECTRICAL SYSTEM · ENGINE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
NHTSA source summary · Original PDF not reviewed by Recallfolio
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the “Speedometer Replacement Label”. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda’s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO’s services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about an unusual thumping / rattling noise coming from the engine compartment. The noise is most pronounced under the following conditions: Engine at idle Transmission in drive Foot on the brake pedal A/C OFF Audio OFF
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the power liftgate (PLG) may open unintentionally while the vehicle is parked or stopped. Due to the shape of the 7th generation remote transmitter, the power liftgate button may be long pressed unintentionally in a pocket or a bag. To eliminate this concern, the keyless control specification has been modified. The button press time has been increased from 0.5 seconds to 1 second.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. NOTE: This repair is not a permanent fix, it is meant to make new seats look their best when the vehicle is first presented to the customer. • Wrinkles may not be completely removed after the repair is completed. • Leather is a natural material and may develop some wrinkles due to aging and wear during normal useage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disk plate’s surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a “Telematics Malfunction” message in the instrument cluster with DTC U3000:04-TCU (Telematics communication unit internal malfunction) stored in memory. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose DTCs according to the instructions on MGSS online.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a “Telematics Malfunction” message in the instrument cluster with DTC U3000:04-TCU (Telematics communication unit internal malfunction) stored in memory. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience the master warning light and/or the "In-Vehicle Network Malfunction" warning message in the instrument cluster on with DTC B119F:01 (TCU - Tel antenna No. 1 malfunction) stored.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose DTCs according to the instructions on MGSS online.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose DTCs according to the instructions on MGSS online.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A new repair procedure has been developed to address DTC P0126:00 on SKYACTIV-G 2.0/2.5L engines (non-turbo). Mazda has introduced a replacement kit of the thermostat located within the Coolant Control Valve (CCV). NOTE: It is no longer necessary to replace the CCV for this DTC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience the following symptoms: No sound from some audio sources (AM, FM, SiriusXM®) after turning the ignition on. Radio station selection (AM, FM, SiriusXM®) changes unintentionally after turning the ignition on. Audio source cannot be changed. Diagnosing according to MGSS online does not solve the problem. These concerns may be caused by the remote tuner not operating properly under certain situations. To eliminate these concerns, the remote tuner control software has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about color discrepancies (brightness differences) of the image displayed on the screen when using the 360°view monitor. As this phenomenon is not a system failure, do not make any repairs or replace any parts. Explain the cause of this occurrence to the customer as follows: The 360°view monitor is a system that provides a complete picture of the vehicle surroundings by combining the pictures captured by 4 separate cameras. These cameras are installed in the front, rear, right and left sides of the vehicle. Each camera has a color adjustment function (white balance) that operates independently from each other, which can result in color discrepancy when the combined picture is displayed on the screen. This is especially true when one of the cameras captures more green objects than the remaining cameras.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission
NHTSA source summary · Original PDF not reviewed by Recallfolio
This service information provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a âTelematics Malfunctionâ message in the instrument cluster with DTC U3000:04-TCU (Telematics communication unit internal malfunction) stored in memory. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A tapping/rattling noise may be noticed from the valve train area. This operating condition can occur on new vehicles which have been delivered to Mazda dealers (due to loading and unloading from transport trucks or customers moving their vehicles in and out of their garages to wash the vehicle, etc.). This condition may also occur if the engine is not allowed to warm up after multiple cold starts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the power liftgate (PLG) may open unintentionally while the vehicle is parked or stopped. Due to the shape of the 7th generation remote transmitter, the power liftgate button may be long pressed unintentionally in a pocket or a bag. To eliminate this concern, the keyless control specification has been modified. The button press time has been increased from 0.5 seconds to 1 second.
Source components: ELECTRICAL SYSTEM · LATCHES/LOCKS/LINKAGES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF, Climate control
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT · EQUIPMENT:ELECTRICAL:INFOTAINMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a âTelematics Malfunctionâ message in the instrument cluster with DTC U3000:04-TCU (Telematics communication unit internal malfunction) stored in memory. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Due to limitations, certain vehicles from 2016 to current models might display an inaccurate transmission part number in the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Frequently Asked Questions (FAQ): General Questions, Reception Level Inspection, Setup and Getting Started, Dealer Processes, Registration / Enrollment, TCU Activation, WI-FI General Information, Conditions for Remote Engine Start Will Not Function, WI-FI How-To Conditions for Remote Engine Start Function Will turn engine OFF, WI-FI Trial Period, Deactivation Mode, Interacting With The App, Educational Videos, Service Issues, Resources, Troubleshooting Page.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the tire sidewalls are distorted or "damaged". Sidewall waviness/indentations/undulations are common on radial tires and are more noticeable on tires with taller sidewalls. The higher the tire pressure, the more noticeable the effect will be. Be sure to set the tire pressures at the recommended tire pressure on the vehicle tire label. Sidewall indentations are a cosmetic condition that does not affect the performance of the tires.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a steering shimmy or body vibration during the PDI test drive or during the first few miles of driving after the vehicle has been delivered to the customer due to flat spots on the tires. Flat spots on tires may be caused by improper maintenance during dealer storage (e.g.: Vehicle was left stationary for a prolonged period of time in high ambient temperatures).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a âTelematics Malfunctionâ message in the instrument cluster with DTC U3000:04-TCU (Telematics communication unit internal malfunction) stored in memory. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN · SERVICE BRAKES, HYDRAULIC · STEERING · TIRES · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Frequently Asked Questions (FAQ): General Questions, Reception Level Inspection, Setup and Getting Started, Dealer Processes, Registration / Enrollment, TCU Activation, WI-FI General Information, Conditions for Remote Engine Start Will Not Function, WI-FI How-To Conditions for Remote Engine Start Function Will turn engine OFF, WI-FI Trial Period, Deactivation Mode, Interacting With The App, Educational Videos, Service Issues, Resources, Troubleshooting Page.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a creaking or clacking noise when operating the power lift gate (PLG). The noise may be caused by the following: Creaking noise: Dust and dirt accumulates on the sealing portion of the PLG drive unit, reducing sealing performance. Snow and water may enter the PLG drive unit. Humidity then causes rust inside of the unit, resulting in noise. Clacking noise: Since the grease applied on the spring end of the PLG drive unit is insufficient, interference noise is caused when the spring end interferes with the spring guide. The noise has been eliminated by the following mass-production changes: Creaking noise: The sealing structure has been modified to prevent dust/dirt from entering the unit. Clacking noise: The production procedure of the PLG drive unit has been modified to apply sufficient grease to spring end.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about a creaking, knocking, rattle or clunk noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. To eliminate this concern, the tightening torque for the steering column nut has been increased.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a âTelematics Malfunctionâ message in the instrument cluster with DTC U3000:04-TCU (Telematics communication unit internal malfunction) stored in memory. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience the check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up The engine temperature gauge fluctuates The low coolant temperature indicator (blue) light stays on longer or comes on while driving Poor heater performance, especially at idle
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit an âIn Vehicle Network Malfunctionâ message appearing in the instrument cluster with DTC U3000:04-TCU (Telematics communication unit internal malfunction) stored after the connected service contract has been discontinued. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified
NHTSA source summary · Original PDF not reviewed by Recallfolio
Before judging a steering wheel as having premature wear or a defect, first clean the steering wheel as explained in the repair information. Some vehicles may have steering wheel stains caused by chemicals such as hand lotions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Frequently Asked Questions (FAQ): General Questions Reception Level Inspection Setup and Getting Started Dealer Processes Registration / Enrollment TCU Activation WI-FI General Informatio Conditions for Remote Engine Start Will Not Function WI-FI How-To Conditions for Remote Engine Start Function Will turn engine OFF WI-FI Trial Period Deactivation Mode Interacting With The App Educational Videos Service Issues Resources Troubleshooting Page
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.. CAUTION: DO NOT swap TCU with another vehicle as the TCU is VIN locked after activation. A TCU swap with another vehicle will disable Connected Services on both vehicles. If TCU activation is not performed, connected vehicle functions will not operate. This will have a negative impact on the customer because they will need to return to the dealer for repairs.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about a creaking noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. To eliminate this concern, the tightening torque for the steering column nut has been increased.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about color discrepancies (brightness differences) of the image displayed on the screen when using the 360°view monitor. As this phenomenon is not a system failure, do not make any repairs or replace any parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the headlights get foggy or have water spots inside. This concern may be caused by the anti-fog coating not preventing inner condensation under certain situations. To eliminate this concern, the anti-fog coating performance was improved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In-Vehicle Network Malfunction error message and Master Warning light ON with DTC U3000:04 (Telematics communication unit internal malfunction) stored.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience no sound from the audio system and/or the audio source cannot be changed. This concern may be caused by the remote tuner not operating properly under certain situations. To eliminate this concern, the remote tuner control software has been modified.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT · EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a chirp noise (stick-slip noise) from the automatic transaxle (AT) when shifting from 3 to 4 while driving. This may be caused by the automatic transaxle fluid (ATF) being contaminated by iron powder due to excessive wearing of the lock up clutch in the torque converter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a chirp noise (stick-slip noise) from the automatic transaxle (AT) when shifting from 3 to 4 while driving. This may be caused by the automatic transaxle fluid (ATF) being contaminated by iron powder due to excessive wearing of the lock up clutch in the torque converter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:ELECTRICAL:INFOTAINMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may notice an abnormal noise (i.e. whine, groan, rattle or squeak) coming from the front combination lights when turning them on, or a few minutes after turning them off. The noise may be due to contamination by foreign matter during the manufacturing process. The fan motor bearing may become worn out during use. To eliminate the noise, the production process at the supplier and the material has been modified. NOTE: It is normal for some noise to occur within the first few seconds after starting the engine, when the front combination lights perform a self check (sweep).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MNAO has recently found an increase in non-returned cores within the United Radio (UR) exchange program. As a reminder, dealers have 90 days, after the order is placed, to return the exchanged part. Failure to return the exchanged part will result in a debit of the full component price. It is highly recommended to set a calendar reminder at the time of the order for no more than 60 days to ensure all orders are returned if repaired and if not repaired, contact the customer to cancel the order and return the unit.