Original record summaries, dates and identifiers for this model-year. Records 101–200 of 571, ordered newest first. Dated records on this page: Sep 1, 2021–Apr 14, 2023.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 14, 2023Service Bulletin/Repair Instructions
SA-023-23
NHTSA communication ID: 10235584
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience any of the following: Engine no start due to battery discharge Ignition cannot be turned OFF Infotainment remains ON after the ignition is turned OFF Infotainment display is blank Commander switch is inoperative Remote transmitters are inoperative This may be caused by a liquid spill at the front cup holder.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. DTC B00A0:09 (Occupant classification sensor internal signal output unstable). This concern is caused by the low voltage detection time of the occupant classification sensor (OCS) being too short during cranking, which causes detection of the DTC unnecessarily. The concern occurs more often in colder weather when greater electric current is consumed to start the vehicle. To eliminate this concern, the OCS has been modified to avoid unnecessary DTC detection. NOTE: Even if the voltage is recovered after the engine is started, the airbag warning light stays ON during the drive cycle. When the battery voltage becomes stable after the engine is started, the airbag system will operate normally.
Source components: AIR BAGS · AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION:STATUS INDICATOR LAMP/LIGHT · ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disk plateâs surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING · SERVICE BRAKES, HYDRAULIC · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The rear differential case could develop a crack in the case. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. This concern is caused when the sliding bearing (1) in the coupling (2) is seized and causes the coupling component to fit loosely. The pinion shaft head (3) then contacts the differential case and causes a crack.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 °F (10°C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced since December 2021 at the supplier.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The rear differential case could develop a crack in the case NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. This concern is caused when the sliding bearing in the coupling is seized and causes the coupling component to fit loosely. The pinion shaft head then contacts the differential case and causes a crack.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When servicing SKYACTIV engine vehicles requiring to replace the Oil Galley Plug and Crush Washer, order the required part numbers below. These parts are not listed in GEPC and were previously listed as "non-serviceable" in the cylinder block diagram.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: DO NOT replace the infotainment center display assembly. Low cost repair kits are available to repair the infotainment center display screen.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Parts Flash replaces RF-22-01R2 released January 04, 2022. It includes new display repair kit part numbers for the 2018-2019 Mazda2, 2018-2020 CX-3 and 2018-2020 MX-5. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Parts Flash replaces RF-22-01R released November 21, 2022. It includes a new display repair kit part number for the 2020-2022 MX-5. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: DO NOT replace the infotainment center display assembly. Low cost repair kits are available to repair the infotainment center display screen.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disk plate's surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about infotainment center display: * Ghost Touch * DTC B108E:04 may be stored (Touch screen operates by itself) * Surface Peeling * DTC B108E:04 may be stored * Spider Cracks * White dots
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.324 or later). The system performance has been improved as follows: Ver. 74.00.324 fixes these software errors (bugs): * If the shift lever is operated quickly while displaying the CarPlayTM screen, the rear view screen may not return to the CarPlayTM screen. * When the gear position is shifted into P from R, the screen may not return to the previous condition before shifting into the R position.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors. Please use the table below when ordering the screen repair kits. This can also be found in Service Alert SA-041/22.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT:VIDEO (TOUCH)SCREEN/MONITOR/UNIT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit the following malfunctions: - The film on the center display is peeling off, as shown in the illustration below. This may be caused by cleaning the center display surface. Water and/or a cleaning solution may get into the scratches on the film and cause the film to start peeling (As a result, DTC B108E:04 may be stored). To eliminate this concern, the anti-reflective film has been modified to reduce scratches during cleaning. - The map on the center display may scroll by itself without operating the map (ghost touch). The thermal expansion and contraction of the touch panel may cause a deformation. Loosening of the touch panel resulting in increased wire resistance may be causing the map malfunction (As a result, DTC B108E:04 may be stored). To eliminate this concern, a protection film has been added in the touch panel to prevent deformation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Cell phone charger/accessory in 12V socket (engine no start or unable to turn off) 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple CarplayâÃÂâ/ Android AutoâÃÂâ will not connect) 6. Over-sized wheels/tires (incorrect GPS location)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain the HVAC system not maintaining the correct temperature or the ambient (outside) temperature reading incorrectly. This is caused by a failure in the ambient temperature sensor. To correct this issue, the ambient temperature sensor has been modified.
Source components: ELECTRICAL SYSTEM · VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit either or both of the following symptoms. 1. The SCBS warning light is illuminated with DTC U045A:68 [FORWARD SENSING CAMERA (FSC)]. U045A:68 Error signal received from parking assist unit 2. The parking sensor indicator is flashing with one or more of the following DTCs of PARKING ASSIST SYSTEM. B1B36:14 Front corner ultrasonic sensor (RH) circuit malfunction B1B36:2A Front corner ultrasonic sensor (RH) characteristic malfunction B1B38:14 Front ultrasonic sensor (RH) circuit malfunction B1B38:2A Front ultrasonic sensor (RH) characteristic malfunction B1B40:14 Front corner ultrasonic sensor (LH) circuit malfunction B1B40:2A Front corner ultrasonic sensor (LH) characteristic malfunction B1B42:14 Front ultrasonic sensor (LH) circuit malfunction B1B42:2A Front ultrasonic sensor (LH) characteristic malfunction Due to insufficient waterproof performance of the front harness short cords (1), water may enter in and accumulate in the C-11 (LH) or C-12 (RH) connectors (2) causing a short circuit between wires and an improper signal being sent from the parking (ultrasonic) sensor to the parking sensor unit. To eliminate this concern, the production process of the front harness short cord has been improved to increase waterproof performance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: * The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following: - The windshield is dirty - The FSC lens is foggy - There is low visibility due to rain, fog or snow - It is at night and there is not enough light - There is direct or reflected sunlight on the FSC - There is problem with the FSC * There is a problem with the AUTOHOLD control function. * There is a problem with the electric parking brake (EPB).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: * C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] * B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] * No DTC - Warning Message only [Gen 7 vehicles built after March 2, 2019] DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. * In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). * In other cases this DTC might be found without a related customer concern. NOTE: In most cases, no dealer visit is necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with a coolant control valve may exhibit difficulties when refilling the coolant because the control valve is closed and air in the engine cannot escape during ignition ON. Therefore, turn the ignition OFF when refilling engine coolant using the radiator filler neck.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit accumulation of dried coolant (1) around the water pipe (2). This is caused by a gap between the housing and pipe due to a press fitting during the manufacturing process. The accumulated coolant is solidified and plugs the gap in high temperature environment and the seepage is stopped and does not progress. This is normal and does not require a part replacement, clean off the dried coolant from around the pipe with a wire brush.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a squeaking noise may be heard from the exhaust manifold when the idle speed drops from fast idle to normal idle speed during cold start. This is caused by a variable valve being stuck in the closed position. When returning from fast idle to normal, the stuck valve suddenly opens due to thermal change around it which causes abnormal noise. To eliminate this concern, the internal design of the exhaust manifold has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about infotainment center display ghost touch (touch screen operates by itself), surface peeling or spider cracks. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT:VIDEO (TOUCH)SCREEN/MONITOR/UNIT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about infotainment center display: - Ghost Touch (Touch screen operates by itself) - Surface Peeling - Spider Cracks Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some CX-5 and CX-30 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch located on the interior liftgate trim. This may be caused by PLG switch corrosion. Water from a high pressure car washer and/or condensation may drip onto the switch connector and cause corrosion. To eliminate this concern, the PLG rear switch has been modified with a waterproof connector. Some Mazda3, CX-30 and MX-30 customers may complain that the vehicle door locking system does not work when the door lock switch on the liftgate interior trim is pressed. DTC B11C4:23 (BCM - liftgate lock switch circuit malfunction) may be stored. This may be caused during a high pressure car wash and/or condensation. Water may enter through the rear center brand emblem base component and drip onto the switch connector causing corrosion. The rusted connector may also cause a battery drain. To eliminate this concern, the rear center brand emblem base has been modified to prevent water entry (Mazda3) and the rear harness has been modified to prevent water infiltration (Mazda3, CX-30 and MX-30).âÂÂ
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about oil seepage or oil leakage from the rear shock absorbers. This concern may be due to a lack of sealing performance. To eliminate the oil seepage/leakage, the rear shock absorbers production process has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about an unusual thumping / rattling noise coming from the engine compartment. The noise is most pronounced under the following conditions: - Engine at idle - Transmission in drive - Foot on the brake pedal - A/C OFF - Audio OFF The noise may be caused by loose fitting heater hoses vibrating the heater hose bracket protector. Page
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about infotainment center display: Ghost touch, surface peeling, spider cracks. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly and occurs more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support. To eliminate this concern, the material of the pads has been changed to copper-free and the specification of the shims has been changed to a coated spring with tape.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit the following malfunctions: - The film on the center display is peeling off, as shown in the illustration below. This may be caused by cleaning the center display surface. Water and/or a cleaning solution may get into the scratches on the film and cause the film to start peeling. To eliminate this concern, the anti-reflective film has been modified to reduce scratches during cleaning. - The map on the center display may scroll by itself without operating the map (ghost touch). The thermal expansion and contraction of the touch panel may cause a deformation. Loosening of the touch panel resulting in increased wire resistance may be causing the map malfunction. To eliminate this concern, a protection film has been added in the touch panel to prevent deformation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. *DTC B00A0:09 (Occupant classification sensor internal signal output unstable) This concern is caused by the low voltage detection time of the occupant classification sensor (OCS) being too short during cranking, which causes detection of the DTC unnecessarily. The concern occurs more often in colder weather when greater electric current is consumed to start the vehicle. To eliminate this concern, the OCS has been modified to avoid unnecessary DTC detection. NOTE: *Even if the voltage is recovered after the engine is started, the airbag warning light stays ON during the drive cycle. *When the battery voltage becomes stable after the engine is started, the airbag system will operate normally.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit corrosion on the liftgate lock striker. This may be caused by water penetrating from micro cracks existing on the lock striker's coating surface that reacts with zinc contained in the undercoating and produces the corrosion. To eliminate this concern, a modified undercoating has been established for the liftgate lock striker.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly. The squeak noise may occur more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about oil seepage or oil leakage from the rear shock absorbers. This concern may be due to a lack of sealing performance. To eliminate the oil seepage/leakage, the rear shock absorbers production process has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
Source components: EQUIPMENT:MECHANICAL · POWER TRAIN · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about a tapping or knocking noise coming from the rear seat after fuel fill. The concern will likely occur if the fuel tank is overfilled (more fuel is added after the fuel pump nozzle shuts off automatically) or filled up normally in high ambient temperatures and the fuel expands. No repair is needed. Explain to the customer not to continue filling after nozzle shut off. Refer customer to Owner's Manual Warning:
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a fuel odor at the left / rear area of the vehicle while the engine is idling that usually occurs when the fuel tank is warmed up in hot weather and/or after long distance driving. Depending on wind direction and/or parking environment, the odor may be more noticeable. The odor may be caused by evaporative gas from the gas outlet vent.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
Source components: POWER TRAIN · SUSPENSION:FRONT:WHEEL BEARING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN · SERVICE BRAKES, HYDRAULIC · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The new AWD rear differential DOES NOT come with a breather cap on the rear of the differential, therefore a new one will need to be ordered and installed when replacing the differential. NOTE: The breather threads have a sealant and locking compound that prevents it from being reused. Refer to GEPC for the correct part number of the Differential Breather. The instructions on MGSS will be updated soon to include replacing the breather when replacing the differential with a new unit.
Source components: POWER TRAIN · POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Use a clean towel damped in leather/vinyl cleaner or mild soap to clean the steering wheel. NOTE: Upholstery maintenance and care information can also be found in the Owner's Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit either or both of the following symptoms. 1. The SCBS warning light is illuminated with DTC U045A:68 [FORWARD SENSING CAMERA (FSC)]. U045A:68 Error signal received from parking assist unit 2. The parking sensor indicator is flashing with one or more of the following DTCs of PARKING ASSIST SYSTEM. B1B36:14 Front corner ultrasonic sensor (RH) circuit malfunction B1B36:2A Front corner ultrasonic sensor (RH) characteristic malfunction B1B38:14 Front ultrasonic sensor (RH) circuit malfunction B1B38:2A Front ultrasonic sensor (RH) characteristic malfunction B1B40:14 Front corner ultrasonic sensor (LH) circuit malfunction B1B40:2A Front corner ultrasonic sensor (LH) characteristic malfunction B1B42:14 Front ultrasonic sensor (LH) circuit malfunction B1B42:2A Front ultrasonic sensor (LH) characteristic malfunction Due to insufficient waterproof performance of the front harness short cords (1), water may enter in and accumulate in the C-11 (LH) or C-12 (RH) connectors (2) causing a short circuit between wires and an improper signal being sent from the parking (ultrasonic) sensor to the parking sensor unit. To eliminate this concern, the production process of the front harness short cord has been improved to increase waterproof performance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some CX-5 and CX-30 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Water from a high pressure car washer and/or condensation may drip onto the switch connector and cause corrosion. To eliminate this concern, the PLG rear switch has been modified with a waterproof connector. Some Mazda3, CX-30 and MX-30 customers may complain that the vehicle door locking system does not work when the door lock switch on the liftgate interior trim is pressed. DTC B11C4:23 (BCM - liftgate lock switch circuit malfunction) may be stored. This may be caused during a high pressure car wash and/or condensation. Water may enter through the rear center brand emblem base component and drip onto the switch connector causing corrosion. The rusted connector may also cause a battery drain. To eliminate this concern, the rear center brand emblem base has been modified to prevent water entry (Mazda3) and the rear harness has been modified to prevent water infiltration (Mazda3, CX-30 and MX-30).
Source components: ELECTRICAL SYSTEM · LATCHES/LOCKS/LINKAGES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit the following malfunctions: 1. The film on the center display is peeling off, as shown in the illustration below. This may be caused by cleaning the center display surface. Water and/or a cleaning solution may get into the scratches on the film and cause the film to start peeling. To eliminate this concern, the anti-reflective film has been modified to reduce scratches during cleaning. 2. The map on the center display may scroll by itself (without operating the map). The thermal expansion and contraction of the touch panel may cause a deformation. Loosening of the touch panel resulting in increased wire resistance may be causing the map malfunction. To eliminate this concern, a protection film has been added in the touch panel to prevent deformation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with Blind Spot Monitoring (BSM) may experience a BSM indicator light on the outer door mirror, even if there is no vehicle in the alert (blind spot) area. NOTE: This concern occurs only after a cold start. As the BSM control module temperature rises, the BSM system returns to normal operation. Due to BSM control module production variances, a false detection may occur in some units when the BSM temperature in the control module has not yet reached normal operating temperature. To eliminate this concern, the control logic of the BSM control module has been modified.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · LANE DEPARTURE · LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. 6 Bluetooth device will not pair No. 7 Incorrect GPS position No. 8 Voice Recognition Does Not Work No. 9 Cannot Make a Hands-Free Call No. 10 Cannot Play Bluetooth Audio No. 11 Other Symptoms No. 12 How to update the Navigation SD Card Map No. 13 How to Check Navi SD Card VIN Lock
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Battery Maintenance: This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Whistling Noise From Front Door Window Glass or Windshield When Driving At Highway Speed: Some customers may complain about a whistling noise heard from the top of the A-pillar area and/or the top of windshield area when driving at highway speeds. When driving under the following conditions, a negative pressure is generated on the doors and the windshield pulling them outward and resulting in weatherstrip vibration. - The vehicle is exposed to a side wind while driving at highway speeds. - The vehicle is exposed to a strong side wind while driving at a speed slightly higher than highway speed. Customers having this concern should have their vehicle repaired using the following repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rusty Panel at Bottom (Inner Side) of Doors: Some customers may complain about rust at the bottom (inner side) of the doors where the seaming welt is located. It is caused by mud/sand adhering to the side sill, which scratches the paint surface when the door is opened/closed. The mud/sand is most likely brought in by the driver and/or passenger when stepping in and out of the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit rust or paint peeling at the inside edge of the front door(s). This may be caused by dust adhering between the front door edge and the rear door weatherstrip, which rubs/damages the paint during vehicle operation (door opening/closing and vibration while driving). NOTE: If the rust/paint peeling is seen on the outer side of the door, this service bulletin does not apply.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NOTE: This Service Information is only applicable for vehicles equipped with a Forward Sensing Camera (FSC), KDD1-67-XCX and GSH7-67-XCX*. If B61L-67-XCX* appears in the GEPC search, the VIN is applicable for this repair only if the part has been previously replaced with KDD1-67-XCX. Some vehicles may exhibit the master warning light (and other warning lights) illuminated while driving, with DTC B115E:76 stored in memory.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the rear door seaming welt (1) comes off when stepping in and/or out of the vehicle. This is caused by the gripping force of the seaming welt being insufficient for frequent usage of the rear seat (vehicle used for ride sharing). No mass production change is planned.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For improvement of electrical diagnosis, the SKYACTIVî Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIVî vehicles and compare suspect terminal drag with a good know terminal.To measure the voltage/resistance avoiding any terminal damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about an unusual thumping / rattling noise coming from the engine compartment. The noise is most pronounced under the following conditions: Engine at idle, Transmission in drive, Foot on the brake pedal, A/C OFF, Audio OFF, The noise may be caused by loose fitting heater hoses vibrating the heater hose bracket protector.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. E85: A blend of 85% ethanol and 15% gasoline All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit insufficient A/C performance / insufficient airflow from vents or ducts. These concerns may be caused by an evaporator temperature sensor malfunction due to insufficient water-proofing. This may result in a detection error and therefore, improper operation of the A/C system. To eliminate this concern, the production process of the evaporator temperature sensor has been modified to ensure proper water-proofing.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:APPLIANCE:AIR CONDITIONER · VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:AIR HANDLER/CHAMBER, DUCTS, AND VALVES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline, E85: A blend of 85% ethanol and 15% gasoline, All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V. What if a customer puts E85 in there Mazda vehicle? Symptoms include: Rough Running, Lean Codes, Misfires and/or misfire codes, Lack of power, Poor fuel economy, Spark knock, Mechanical engine damage.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with Blind Spot Monitoring (BSM) may experience a BSM indicator light on the outer door mirror, even if there is no vehicle in the alert (blind spot) area. NOTE: This concern occurs only after a cold start. As the BSM control module temperature rises, the BSM system returns to normal operation. Due to BSM control module production variances, a false detection may occur in some units when the BSM temperature in the control module has not yet reached normal operating temperature. To eliminate this concern, the control logic of the BSM control module has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about a whistling noise heard from the top of the A-pillar area when driving at highway speeds. When driving under following conditions, a negative pressure is generated on the doors pulling them outward and resulting in weatherstrip vibration. The vehicle is exposed to a side wind while driving at highway speeds. The vehicle is exposed to a strong side wind while driving at a speed slightly higher than highway speed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.230 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of MazdaâÂÂs continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software. Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit rust or paint peeling at the inside edge of the front door(s). This may be caused by dust adhering between the front door edge and the rear door weatherstrip, which rubs/damages the paint during vehicle operation (door opening/closing and vibration while driving).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit: Vehicle body vibration when moving from a stop while using the Electric Parking Brake (EPB) automatic release function. Uneven rear brake pad wear. These concerns may be caused because the automatic EPB caliper release timing is too late for the movement of the vehicle. NOTE: Frequent usage of the EPB automatic release function may promote uneven rear brake pad wear. To eliminate these concerns, the EPB control module logic has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a squeaking noise from the blower motor while it is operating. This is caused by burrs that were not trimmed completely in the manufacturing process of the blower motor. To eliminate this concern, the manufacturing process of the blower motor has been modified to efficiently trim burrs.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on, P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on, P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on, P0780:00 - Gear shifting malfunction, P1738:00 Automatic transaxle internal malfunction. This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.