2011 Kia SORENTO Manufacturer communications & TSBs.Page 1
Original record summaries, dates and identifiers for this model-year. Records 1–100 of 202, ordered newest first. Dated records on this page: Jun 17, 2016–Jun 8, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jun 8, 2026Service Bulletin/Repair Instructions
CS2312_TSB_R2
NHTSA communication ID: 11034003
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: THEFT DETERRENT IGNITION CYLINDER PROTECTOR AND DECAL INSTALLATION (CS2312) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: THEFT DETERRENT IGNITION CYLINDER PROTECTOR AND DECAL INSTALLATION (CS2312) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whole Integrated Body control Unit (IBU) / Body Control Module (BCM) did receive the Ant-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: THEFT DETERRENT IGNITION CYLINDER PROTECTOR AND DECAL INSTALLATION (CS2312) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 19, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CUSTOMER SATISFACTION CAMPAIGN: OWNER NOTIFICATION (CS2312) - This document is the owner notification advising that Kia is conducting Customer Satisfaction Campaign. A software upgrade that addresses the social media theft method has been made available to owners of eligible Kia model vehicles free of charge at authorized Kia dealers since 2023. In addition to the anti-theft software, a new zinc-reinforced ignition cylinder protector hardware upgrade has been developed and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because the subject Kia vehicles were not factory-equipped with an engine immobilizer and were previously eligible for the software upgrade, these vehicles are eligible until March 31, 2027, to have the ignition cylinder protector installed—if requested—at no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 17, 2025 through February 27, 2026)
NHTSA source summary · Original PDF not reviewed by Recallfolio
PITSTOP: TECHNICAL OPERATIONS: EXTERNAL DAMAGE TO ULTRASONIC SENSOR: This Pitstop provides information related to Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a “Warning Lamp’ to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)
Source components: BACK OVER PREVENTION: WARNINGS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: OCCUPANT DETECTION SYSTEM (ODS) SENSOR PAD REPLACEMENT - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to replace the front passenger Occupant Detection System (ODS) Sensor Pad on 2011-2015MY Sorento (XMa) vehicles produced from September 24, 2009 through December 11, 2014. If the Occupant Detection System (ODS) Sensor Pad is not operating properly, the airbag warning light will illuminate and certain specific DTC(s) listed in this bulletin may be stored:
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: TRANSMISSION FLUID APPLICATION GUIDE - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: SUBSEQUENT REPAIR ACTION: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (SC291YZ) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (SC291) titled “Engine Inspection/Replacement and KSDS Software Installation” for 2011MY Sorento (XMa) vehicles equipped with Theta 2.4L MPI engine, produced from October 24, 2009 through June 24, 2011. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: AIRBAG WARNING LIGHT ON (WTY003) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the replacement of the clock spring assembly on 2011MY - 2015MY Sorento (XMa) vehicles. Kia is extending the warranty coverage for the driver’s front airbag clock spring assembly on the 2011-2015 MY Sorento vehicles, manufactured from 10/24/2009 through 12/17/2014, to fifteen (15) years with unlimited mileage, starting from the date of first service. This warranty extension addresses failures of the driver’s front airbag clock spring, as well as the diagnosis of any concerns related to the airbag warning light.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: PRODUCT IMPROVEMENT CAMPAIGN: SUBSEQUENT REPAIR ACTION: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI2101Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (PI2101) titled “Knock Sensor Detection System - ECU Logic Improvement” for 2011MY Sorento (XMa) vehicles equipped with Theta 2.4L MPI engine, produced from October 24, 2009 through June 24, 2011. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2304) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked with the use of the key fob.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2304) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PITSTOP: AWD SYSTEM CONCERN DUE TO TIRE CIRCUMFERENCE - This Pitstop provides information regarding potential concerns with the All-Wheel-Drive (AWD) system due to tire sizes of differing circumference. Some customers may complain of a chatter sensation felt in the drivetrain of the vehicle and/or the failure of drivetrain component(s). A difference in tire size (width, aspect ratio, construction, rim diameter etc.) may be the cause.
Source components: POWER TRAIN · STEERING · SUSPENSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2304) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CUSTOMER SATISFACTION CAMPAIGN: OWNER RE-NOTIFICATION - This document is the owner re-notification advising that Kia has developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of the original letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to the vehicle to discourage a break-in.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2304) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2304) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2304) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:IGNITION:ANTI-THEFT:CONTROL MODULE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: CUSTOMER SATISFACTION: ANTI-THEFT S/W LOGIC UPGRADE & DECAL INSTALLATION (CS2304) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area.This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM), or Intelligent Integrated Platform Module (IPM) system on certain 2011-2015MY Sorento (XMa), 2016-2020MY Sorento (UMa), and 2021-2022MY Sorento (MQ4a) vehicles produced within the dates outlined on page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CUSTOMER SATISFACTION CAMPAIGN: OWNER NOTIFICATION - This document is the owner notification advising that Kia has developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: TRANSMISSION FLUID APPLICATION GUIDE - This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: BEARING CLEARANCE TESTER (BCT) PROCEDURES - This bulletin provides information regarding test procedure of the Bearing Clearance Tester (BCT) Special Service Tool (SST). The SST comes pre-calibrated from the supplier however, in some cases, due to variable shop compressor air pressure, the SST may need to be re-calibrated to ensure that the tool provides accurate readings when testing the engine rod bearing wear. The calibration and BCT measuring point maintenance is included in this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBSEQUENT REPAIR ACTION: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI2101Y/Z) - This bulletin provides information related to the Technical Service Bulletin previously published in (PI2101) titled "Knock Sensor Detection System - ECU Logic Improvement" for 2011MY Sorento (XMa) vehicles equipped with Theta 2.4L MPI engine, produced from October 24, 2009 through June 24, 2011. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information regarding test procedure of the Bearing Clearance Tester (BCT) Special Service Tool (SST). The SST comes pre-calibrated from the supplier however, in some cases, due to variable shop compressor air pressure, the SST may need to be re-calibrated to ensure that the tool provides accurate readings when testing the engine rod bearing wear. The calibration and BCT measuring point maintenance is included in this bulletin.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: INFORMATION FOR HEADLAMP CONDENSATION AND MOISTURE - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN - PRODUCT IMPROVEMENT CAMPAIGN PI2101 - THETA 2.4L MPI - KNOCK SENSOR DETECTION SYSTEM (KSDS) ECU LOGIC IMPROVEMENT (PI2101) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: EXCESSIVE OIL CONSUMPTION NU/GAMMA/THETA ENGINES - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PRODUCT IMPROVEMENT CAMPAIGN - OWNER LETTER - This document is notice to the 2011 MY Sorento vehicle owners advising them of the Product Improvement Campaign on their vehicles.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN - PRODUCT IMPROVEMENT CAMPAIGN PI2101 - THETA 2.4L MPI - KNOCK SENSOR DETECTION SYSTEM (KSDS) ECU LOGIC IMPROVEMENT (PI2101) - This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PRODUCT IMPROVEMENT CAMPAIGN - DEALER SERVICE MANAGER LETTER - This document is notice to the Dealer Service Managers advising them of the Product Improvement Campaign.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PRODUCT IMPROVEMENT CAMPAIGN - DEALER PRINCIPAL LETTER - This document is the notice to the dealer principals notifying them of the Product Improvement Campaign.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WARRANTY EXTENSION PROGRAM - This document is the notice to the vehicle owners, advising them of the Warranty Extension on the Occupant Detection System Sensor Pad to fifteen (15) years with unlimited mileage, starting from the date the vehicle was first put into service.
Source components: AIR BAGS · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · SEATS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WARRANTY EXTENSION PROGRAM - This document is the notice to the vehicle owners, advising them of the Warranty Extension on the Occupant Detection System Sensor Pad to fifteen (15) years with unlimited mileage, starting from the date the vehicle was first put into service.
Source components: AIR BAGS · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · SEATS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WARRANTY EXTENSION PROGRAM - This document is the Question and Answer document regarding the Warranty Extension on the Occupant Detection System Sensor Pad to fifteen (15) years with unlimited mileage, starting from the date the vehicle was first put into service.
Source components: AIR BAGS · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · SEATS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WARRANTY EXTENSION PROGRAM - This document is the notice to dealer parts and service managers, advising them of the Warranty Extension on the Occupant Detection System Sensor Pad to fifteen (15) years with unlimited mileage, starting from the date the vehicle was first put into service.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WARRANTY EXTENSION PROGRAM - This document is the notice to dealer principals, advising them of the Warranty Extension on the Occupant Detection System Sensor Pad to fifteen (15) years with unlimited mileage, starting from the date the vehicle was first put into service.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PITSTOP - BRAKE CALIPER LEAK INSPECTION - This PITSTOP provides information related to a brake caliper fluid/oil substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.
Source components: EQUIPMENT · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:CALIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: - TRANSMISSION FLUID APPLICATION GUIDE - This bulletin has been revised to include additional information. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles on page 2. Refer to the shop manual on KGIS for the specific Kia model for the correct transmission fluid check/fill procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: OCCUPANT DETECTION SYSTEM (ODS) SENSOR PAD REPLACEMENT - This bulletin provides the procedure to replace the front passenger Occupant Detection System (ODS) Sensor Pad on 2011-2015MY Sorento (XMa) vehicles produced from September 24, 2009 through December 11, 2014.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: STEERING GEAR YOKE PLUG AND ASSEMBLY REPLACEMENT - This bulletin has been revised to include additional information. This bulletin provides the procedure to replace the steering gear box yoke plug and assembly on some models listed below, which may exhibit a ticking noise while turning the steering wheel with the vehicle stopped. This condition is caused by a worn lining on the steering gear box yoke assembly. Follow the procedure outlined in this bulletin to replace the steering gear box yoke plug and assembly with updated parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TECHNICAL SERVICE BULLETIN TSB084_R3: PARTIAL REPAIR OF C-MDPS MOTOR, ECU AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This document is a Request for Reimbursement Form sent to the owners along with the notification letter to be used if the customer has paid for repairs to the airbag clock spring assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WTY003_OWNER: This document is the owner notification letter advising the owners of the warranty extension on the 2011-2015 My Sorento Airbag Clock Spring Assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB: HALOGEN LOW BEAM BULB CONNECTOR REPLACEMENT - This bulletin provides the procedure to replace the halogen low beam bulb connector on some 2011 - 2013MY Sorento (XMa) vehicles, produced from October 24, 2009 through January 31, 2013, which may experience an inoperable low beam bulb due to poor terminal contact at the low beam bulb connector.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Dear Kia Sorento Owner - Kia Motors America, Inc. takes pride in providing you with high quality and dependable vehicles. In order to maintain these standards, Kia is extending the New Vehicle Limited Warranty coverage, to all owners of 2011-2013 MY Kia Sorento vehicles, for the halogen headlamp low beam connector wiring harness from 5-years/60,000-miles to 10-years/unlimited-miles, starting from the date of first service. The headlamp connectors may lose electrical contact with a low beam bulb in one of the headlamp assemblies. This condition on the affected headlamp does not affect the other low beam. In addition, the high beams continue to function at all times.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB: HALOGEN LOW BEAM BULB CONNECTOR REPLACEMENT - This bulletin provides the procedure to replace the halogen low beam bulb connector on some 2011 - 2013MY Sorento (XMa) vehicles, produced from October 24, 2009 through January 31, 2013, which may experience an inoperable low beam bulb due to poor terminal contact at the low beam bulb connector. This condition on the affected headlamp does not affect the other low beam. In addition, the high beams continue to function at all times.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Attention: All Kia Parts & Service Managers - Kia Motors America, Inc. is extending the New Vehicle Limited Warranty coverage to all owners of the 2011-2013 MY Kia Sorento vehicles, produced from October 24, 2009 through January 31, 2013, for the halogen headlamp low beam connector wiring harness from 5-years/60,000-miles to 10-years/unlimited-miles, starting from the date of first service. The headlamp connectors may lose electrical contact with a low beam bulb in one of the headlamp assemblies. This condition on the affected headlamp does not affect the other low beam. In addition, the high beams continue to function at all times.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Attention: All Dealer Principals - Kia Motors America, Inc. is extending the New Vehicle Limited Warranty coverage to all owners of the 2011-2013 MY Kia Sorento vehicles, produced from October 24, 2009 through January 31, 2013, for the halogen headlamp low beam connector wiring harness from 5-years/60,000-miles to 10-years/unlimited-miles, starting from the date of first service. The headlamp connectors may lose electrical contact with a low beam bulb in one of the headlamp assemblies. This condition on the affected headlamp does not affect the other low beam. In addition, the high beams continue to function at all times.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DEALER COMMUNICATION - RECENT KIA MEDIA REPORTS, OCTOBER 26 2018 UPDATE - Dear Kia Retailer, We wrote to you in late August to provide you with an update regarding news reports regarding non-collision fires in Kia vehicles and NHTSA?s announcement of the opening of a Defect Petition for fire cases involving the 2011-14 Sorento and Optima vehicles. Since that time, we have been working cooperatively with NHTSA to analyze the safety performance of these and all Kia vehicles and added additional resources to quickly and effectively address any incidents. Recently, a non-profit consumer advocacy group called the Center for Automotive Safety (CAS) has asked for a recall of Kia vehicles for fire risk and members of the Senate Commerce Committee have asked Kia for additional information related to non-collision fires in Kia vehicles. These actions have generated additional media reports so we are providing you with additional information to assist you and your teams in addressing customer concerns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DEALER COMMUNICATION - RECENT KIA MEDIA REPORTS - Dear Kia Retailer, You and your customers may have seen recent media reports regarding thermal incidents in Kia vehicles or NHTSA?s announcement of the opening of a Defect Petition for fire cases involving the 2011-14 Sorentos and Optimas, and I want to update you on KMA?s response to this issue. All automobiles contain combustible materials and a vehicle fire may be a result of any number of complex factors which must be carefully evaluated by trained technicians to, if possible, determine its cause and, ultimately, determine if a defect trend exists. At Kia, customer safety is paramount and although both KMA and NHTSA have independently concluded that no defect trends exist, KMA has significantly increased its committed resources to ensure that all thermal incidents are fully evaluated.
Source components: ELECTRICAL SYSTEM · ENGINE · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PITSTOP - ENGINE COMPONENT RE-USE GUIDELINES - In general, parts and components removed during engine repairs should be considered serviceable, and should be thoroughly cleaned and transferred to the new engine.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB - DRIVESHAFT SERVICEABILITY - This bulletin has been revised most recently to include additional information. This bulletin provides information regarding axle shaft serviceability for Kia vehicles equipped with a six-speed automatic transmission.
Source components: POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB - IDENTIFYING HEAD UNIT SOFTWARE VERSION FOR DIRECT EXCHANGE - This bulletin provides the procedure on how to identify and record the head unit software level on various head unit platforms and generations.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PITSTOP: TPMS SENSOR POSITION - When diagnosing TPMS-related DTCs, make sure you are investigating the correct sensor. The TPMS positioning from the manufacturer may be different from the positioning shown on a KDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB: REAR WHEEL SPEED SENSOR HOUSING COVER INSPECTION AND/OR REPLACEMENT (SC148) - VOLUNTARY SERVICE CAMPAIGN - This bulletin provides the procedure on how to inspect, clean and seal or, if necessary, replace the rear wheel speed sensor (WSS) housing covers on certain 2011-2015MY 2WD Sorento (XMa) vehicles, produced from October 24, 2009 through April 30, 2014, originally retailed and/or currently registered in the coastal states of Alabama, Florida, Georgia, Hawaii, Louisiana, Mississippi, North Carolina, South Carolina and Texas. If the rear wheel hub comes into contact with a significant amount of seawater, the water can enter the rear wheel speed sensor housing covers and may interrupt the rear wheel speed sensor signal and illuminate the Anti-Lock Braking System (?ABS?) and/or Electronic Stability Control (?ESC?) warning lights in the instrument cluster.
Source components: ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC) · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB: SC149R1 - HALOGEN HEADLAMP LOW BEAM CONNECTOR REPLACEMENT (SC149) - This bulletin provides the procedure to replace the halogen headlamp low beam connector wiring harnesses on some 2011-2012MY Sorento (XMa) vehicles, produced from April 25, 2011 through June 16, 2011. In a limited production of these vehicles, a small number of headlamp connectors may lose electrical contact with a low beam bulb in one of the headlamp assemblies. This condition on the affected headlamp does not affect the other low beam. Also, the high beams continue to function at all times. Follow the procedure outlined in this bulletin to replace the low beam connector wiring harnesses. Before conducting the procedure, verify that the vehicle is included in the list of affected VINs.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SC148OWNER - OWNER NOTIFICATION LETTER -Notifying owners that Kia is conducting a Voluntary Service Campaign to inspect, clean, and seal, or if necessary, replace the rear wheel speed sensor housing covers on certain 2011-2015 MY Sorento 2-Wheel Drive (2WD) vehicles originally purchased and/or currently registered in the coastal states of Alabama, Florida, Georgia, Hawaii, Louisiana, Mississippi, North Carolina, South Carolina, and Texas.
Source components: SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SC148DPSM - DEALER PARTS & SERVICE MANAGER NOTIFICATION LETTER - Notifies dealer principals of a Voluntary Service Campaign to inspect, clean, and seal, or if necessary, replace the rear wheel speed sensor housing covers on certain 2011 - 2015 MY Sorento 2-Wheel Drive vehicles originally purchased and/or currently registered in the coastal states of Alabama, Florida, Georgia, Hawaii, Louisiana, Mississippi, North Carolina, South Carolina, and Texas.
Source components: SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SC148DP - DEALER PRINCIPAL NOTIFICATION LETTER - Notifies dealer principals of a Voluntary Service Campaign to inspect, clean, and seal, or if necessary, replace the rear wheel speed sensor housing covers on certain 2011 - 2015 MY Sorento 2-Wheel Drive vehicles originally purchased and/or currently registered in the coastal states of Alabama, Florida, Georgia, Hawaii, Louisiana, Mississippi, North Carolina, South Carolina, and Texas.
Source components: SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SC149DPSM - DEALER PARTS AND SERVICE MANAGER NOTIFICATION LETTER - Notifies dealer parts and service managers of a Voluntary Service Campaign to replace the halogen headlamp low beam connector wiring harnesses on certain 2012 MY Sorento vehicles manufactured from April 25, 2011 through June 16, 2011. In a limited production of these vehicles, a small number of headlamp connectors may lose electrical contact with a low beam bulb in one of the headlamp assemblies. This condition on the affected headlamp does not affect the other low beam. Also, the high beams continue to function at all times.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING · EXTERIOR LIGHTING:HEADLIGHTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SC149DP - DEALER PRINCIPAL NOTIFICATION LETTER - Notifies dealer principals of a Voluntary Service Campaign to replace the halogen headlamp low beam connector wiring harnesses on certain 2012 MY Sorento vehicles manufactured from April 25, 2011 through June 16, 2011. In a limited production of these vehicles, a small number of headlamp connectors may lose electrical contact with a low beam bulb in one of the headlamp assemblies. This condition on the affected headlamp does not affect the other low beam. Also, the high beams continue to function at all times.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING · EXTERIOR LIGHTING:HEADLIGHTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB: A/C EVAPORATOR FREEZE-UP DURING EXTENDED DRIVE - This bulletin provides the procedure to replace the evaporator temperature sensor of some 2011-2014MY Optima (TF/QF) and 2011-2013MY Sorento (XMa) vehicles ONLY (see production dates on Page 3), which may experience freezing of condensation on the evaporator core and the following A/C performance related concerns below. Do NOT refer to this bulletin or the resistance specifications listed in this bulletin for ANY other models.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB: DEFOGGING LOGIC ? NORMAL OPERATION, DISABLING, AND ENABLING - Starting with 2010MY, all Kia vehicles, except Rio (JB), incorporate a defogging logic to prevent the interior windows from becoming excessively fogged. Depending on the specific model, the HVAC control head monitors ambient temperature and/or cabin humidity to determine which settings will best prevent the windows from fogging. If the system detects lower ambient temperature or higher cabin humidity, the defogging logic may automatically switch ON the A/C, and/or set the air intake mode to Fresh Air. If the user changes these settings, the defogging logic will take control again after 3 to 5 minutes, depending on the procedure in this publication.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB: SC141 - SERVICE CAMPAIGN - APPLICATION OF ADDITIONAL ANTI-CORROSION MATERIAL - To improve customer satisfaction, Kia is launching this service campaign to apply additional anti-corrosion material to the underbody components of certain 2011-2014MY Sorento, 2011-2014MY Optima and Optima Hybrid, 2011-2014MY Sportage, and 2010-2013MY Forte and Forte Koup vehicles originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV.
Source components: STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB: FRONT DOOR LATCH - CUSTOMER SATISFACTION PROGRAM (CS1603) - This bulletin provides information regarding the inspection, upgrade and/or replacement of door latches on 2011MY Sorento (XMa) vehicles. Kia has determined that after extended usage over years, the door latches may not function properly when being activated with the outside handle and the door may not open.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB: MANDATORY REPLACEMENT OF LOCKING/SECURITY HARDWARE - By design, certain fasteners, which are designed to lock into place once fully attached, are utilized in various Kia models and are strictly intended for ?one time use.? Some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.? It is critical for technicians to be aware that ALL such locking fasteners, regardless of type, are for ?one time use? only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SC141 - SORENTO OWNER LETTER - Dear Kia Sorento Owner: Kia Motors America, Inc. is conducting a Voluntary Service Campaign to apply additional anti-corrosion material to the underbody components of certain 2011-2014 MY Sorento vehicles that were originally sold in or are currently registered in the states where heavy amounts of road salt are used.
Source components: STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB: SC141 - SERVICE CAMPAIGN - APPLICATION OF ADDITIONAL ANTI-CORROSION MATERIAL - To improve customer satisfaction, Kia is launching this service campaign to apply additional anti-corrosion material to the underbody components of certain 2011-2014MY Sorento, 2011-2014MY Optima and Optima Hybrid, 2011-2014MY Sportage, and 2010-2013MY Forte and Forte Koup vehicles originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV.
Source components: STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE MANAGER MEMO: SC141 - SERVICE CAMPAIGN - Attention: All Kia Service Managers - Kia Motors America, Inc. will be conducting a Voluntary Service Campaign, as a preventative measure, to apply additional anti-corrosion material to the underbody components of certain 2011-2014 MY Sorento, 2011-2014 MY Optima and Optima Hybrid, 2011-2014 MY Sportage, and 2010-2013 Forte and Forte Koup vehicles originally retailed or currently registered in one of the 28 states where heavy amounts of road salt are used.
Source components: STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DEALER PRINCIPAL MEMO: SC141 - SERVICE CAMPAIGN - Attention: All Kia Dealer Principals - Kia Motors America, Inc. will be conducting a Voluntary Service Campaign, as a preventative measure, to apply additional anti-corrosion material to the underbody components of certain 2011-2014 MY Sorento, 2011-2014 MY Optima and Optima Hybrid, 2011-2014 MY Sportage, and 2010-2013 Forte and Forte Koup vehicles originally retailed or currently registered in one of the 28 states where heavy amounts of road salt are used.
Source components: STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB: MANDATORY REPLACEMENT OF LOCKING/SECURITY HARDWARE - By design, certain fasteners utilized in various Kia models are strictly intended for ?one time use?. Though not limited to the following, some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.?
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB: INHIBITOR SWITCH DIAGNOSIS INFORMATION - This bulletin gives information regarding the steps to take regarding the diagnosis of the Inhibitor Switch.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PITSTOP: HVAC RECEIVER/DRYER - DESICCANT REPLACEMENT - IN THE EVENT OF A HVAC SYSTEM CONCERN IN WHICH METAL PARTICLES OR SHARDS HAVE CONTAMINATED THE SYSTEM, THE DESICCANT OR THE ENTIRE A/C RECEIVER/DRYER ASSEMBLY MAY NEED TO BE REPLACED. THIS IS DUE TO THE FACT THAT IT MAY BE IMPOSSIBLE TO REMOVE ALL METAL CONTAMINANTS FROM THE RECEIVER/DRYER DURING THE A/C FLUSHING PROCEDURE. REFER TO THE INCLUDED TABLE FOR DETAILED INFORMATION ON COMPONENT REPLACEMENT BY MODEL. IF YOU SUSPECT A PLUGGED EXPANSION VALVE, THE INLET SCREENS CAN BE CLEANED. IF THE VALVE IS NOT EQUIPPED WITH AN INLET SCREEN AND IS RESTRICTED, THE EXPANSION VALVE MAY ALSO NEED TO BE REPLACED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB: FRONT DOOR LATCH CUSTOMER SATISFACTION PROGRAM (CS1603) - THIS BULLETIN PROVIDES INFORMATION REGARDING THE INSPECTION, UPGRADE AND/OR REPLACEMENT OF DOOR LATCHES ON 2011MY SORENTO (XMA) VEHICLES. KIA HAS DETERMINED THAT AFTER EXTENDED USAGE OVER YEARS, THE DOOR LATCHES MAY NOT FUNCTION PROPERLY WHEN BEING ACTIVATED WITH THE OUTSIDE HANDLE AND THE DOOR MAY NOT OPEN. * FOR FRONT DOOR LATCHES: VEHICLES MAY HAVE PREVIOUSLY HAD ONE OR BOTH FRONT DOOR LATCHES REPLACED WITH IMPROVED ONES. THEREFORE, EACH VEHICLE MUST BE CONFIRMED IN WEBDCS WHETHER IT IS ELIGIBLE TO HAVE EITHER DRIVERS OR FRONT PASSENGERS OR BOTH FRONT DOOR LATCHES INSPECTED, UPGRADED AND/OR REPLACED. IF THE ELIGIBLE DRIVER AND/OR FRONT PASSENGER DOOR LATCHES ARE PROPERLY FUNCTIONING, UPGRADE THE DRIVER AND/OR FRONT PASSENGER DOOR LATCHES BY INSTALLING A SPACER CLIP TO THE LATCHES. IF THE ELIGIBLE DRIVER AND/OR FRONT PASSENGER DOOR LATCHES ARE NOT PROPERLY FUNCTIONING, REPLACE THE DRIVER AND/OR FRONT PASSENGER DOOR LATCHES WITH NEW ONES. * FOR REAR DOOR LATCHES: KIA IS EXTENDING THE WARRANTY ON REAR DOOR LATCHES FROM 5 YEARS/60,000 MILES TO 10 YEARS/UNLIMITED MILEAGE, STARTING FROM THE DATE OF FIRST SERVICE. IF, WITHIN THE EXTENDED WARRANTY PERIOD, EITHER REAR DOOR LATCH DOES NOT FUNCTION PROPERLY WHEN BEING ACTIVATED WITH THE OUTSIDE HANDLE AND THE DOOR DOES NOT OPEN, REPLACE THE AFFECTED DOOR LATCH WITH A NEW ONE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
OWNER LETTER: CS1603 - CUSTOMER SATISFACTION/WARRANTY EXTENSION PROGRAM - DEAR KIA SORENTO OWNER: KIA MOTORS AMERICA, INC. WOULD LIKE TO THANK YOU FOR PURCHASING A KIA SORENTO. BECAUSE KIA VALUES YOU AS OUR CUSTOMER, WE ARE CONDUCTING A CUSTOMER SATISFACTION PROGRAM REGARDING DOOR LATCHES IN 2011 MY SORENTO VEHICLES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
REQUEST FOR REIMBURSEMENT FORM: CS1603 - 2011MY KIA SORENTO DOOR LATCHES CUSTOMER SATISFACTION / WARRANTY EXTENSION PROGRAM - IF YOU HAVE PAID TO HAVE THE FRONT AND/OR REAR DOOR LATCHES REPAIRED OR REPLACED, YOU MAY BE ELIGIBLE FOR REIMBURSEMENT FOR SOME OR ALL OF THAT EXPENSE. MAIL THIS COMPLETED REQUEST FOR REIMBURSEMENT FORM TO KIA, ALONG WITH DOCUMENTATION SPECIFIED BELOW, FOR REVIEW AND CONSIDERATION AT THE FOLLOWING ADDRESS: CONSUMER ASSISTANCE CENTER, KIA MOTORS AMERICA, INC., P.O. BOX 52410, IRVINE, CA 92619-2410
NHTSA source summary · Original PDF not reviewed by Recallfolio
DEALER PARTS AND SERVICE MANAGER MEMO: CS1603 - KIA MOTORS AMERICA, INC. IS CONDUCTING A CUSTOMER SATISFACTION / WARRANTY EXTENSION PROGRAM REGARDING THE DOOR LATCHES IN 2011 MY SORENTO VEHICLES. KIA HAS DETERMINED THAT AFTER EXTENDED USAGE OVER YEARS, THE DOOR LATCHES MAY NOT FUNCTION PROPERLY WHEN BEING ACTIVATED WITH THE OUTSIDE HANDLE AND THE DOOR MAY NOT OPEN (HOWEVER, THE DOOR CAN BE OPENED WHEN ANY INSIDE HANDLE IS ACTIVATED.) FRONT DOOR LATCHES. IF THE DRIVER AND/OR FRONT PASSENGER DOOR LATCHES ARE PROPERLY FUNCTIONING, UPGRADE THE DRIVER AND/OR FRONT PASSENGER DOOR LATCHES BY INSTALLING A SPACER CLIP TO THE LATCHES. IF THE DRIVER AND/OR FRONT PASSENGER DOOR LATCHES ARE NOT PROPERLY FUNCTIONING, REPLACE THE DRIVER AND/OR FRONT PASSENGER DOOR LATCHES. THIS UPGRADE OR REPLACEMENT WILL BE PERFORMED AT NO COST TO THE CUSTOMER. IF ONE OF THE FRONT DOOR LATCHES HAS ALREADY BEEN REPLACED, THE OTHER FRONT DOOR LATCH WILL BE UPGRADED OR REPLACED AT NO COST TO THE CUSTOMER. REAR DOOR LATCHES. IN ADDITION, KIA IS EXTENDING THE WARRANTY ON THE REAR DOOR LATCHES FROM 5 YEARS/60,000 MILES TO 10 YEARS/UNLIMITED MILEAGE, STARTING FROM THE DATE OF FIRST SERVICE. IF, AT ANY TIME WITHIN THE EXTENDED WARRANTY PERIOD, THE CUSTOMER EXPERIENCES THE CONDITION DESCRIBED ABOVE, REPLACE THE REAR DOOR LATCHES AT NO COST TO THE CUSTOMER. THE REMAINDER OF THE BASIC WARRANTY FOR COMPONENTS OTHER THAN THE REAR DOOR LATCHES REMAINS UNCHANGED AT 5 YEARS/60,000 MILES. ALL OTHER WARRANTY TERMS, LIMITATIONS AND CONDITIONS APPLY AND REMAIN UNCHANGED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DEALER PRINCIPAL MEMO: CS1603 - KIA MOTORS AMERICA, INC. IS CONDUCTING A CUSTOMER SATISFACTION / WARRANTY EXTENSION PROGRAM REGARDING THE DOOR LATCHES IN 2011 MY SORENTO VEHICLES. KIA HAS DETERMINED THAT AFTER EXTENDED USAGE OVER YEARS, THE DOOR LATCHES MAY NOT FUNCTION PROPERLY WHEN BEING ACTIVATED WITH THE OUTSIDE HANDLE AND THE DOOR MAY NOT OPEN (HOWEVER, THE DOOR CAN BE OPENED WHEN ANY INSIDE HANDLE IS ACTIVATED.) FRONT DOOR LATCHES. IF THE DRIVER AND/OR FRONT PASSENGER DOOR LATCHES ARE PROPERLY FUNCTIONING, UPGRADE THE DRIVER AND/OR FRONT PASSENGER DOOR LATCHES BY INSTALLING A SPACER CLIP TO THE LATCHES. IF THE DRIVER AND/OR FRONT PASSENGER DOOR LATCHES ARE NOT PROPERLY FUNCTIONING, REPLACE THE DRIVER AND/OR FRONT PASSENGER DOOR LATCHES. THIS UPGRADE OR REPLACEMENT WILL BE PERFORMED AT NO COST TO THE CUSTOMER. IF ONE OF THE FRONT DOOR LATCHES HAS ALREADY BEEN REPLACED, THE OTHER FRONT DOOR LATCH WILL BE UPGRADED OR REPLACED AT NO COST TO THE CUSTOMER. REAR DOOR LATCHES. IN ADDITION, KIA IS EXTENDING THE WARRANTY ON THE REAR DOOR LATCHES FROM 5 YEARS/60,000 MILES TO 10 YEARS/UNLIMITED MILEAGE, STARTING FROM THE DATE OF FIRST SERVICE. IF, AT ANY TIME WITHIN THE EXTENDED WARRANTY PERIOD, THE CUSTOMER EXPERIENCES THE CONDITION DESCRIBED ABOVE, REPLACE THE REAR DOOR LATCHES AT NO COST TO THE CUSTOMER. THE REMAINDER OF THE BASIC WARRANTY FOR COMPONENTS OTHER THAN THE REAR DOOR LATCHES REMAINS UNCHANGED AT 5 YEARS/60,000 MILES. ALL OTHER WARRANTY TERMS, LIMITATIONS AND CONDITIONS APPLY AND REMAIN UNCHANGED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WARRANTY BULLETIN: WTY003 - 2011-2015 MY SORENTO DRIVER'S FRONT AIRBAG CLOCK SPRING ASSEMBLY WARRANTY EXTENSION (WTY003) - THIS BULLETIN PROVIDES INFORMATION RELATED TO THE REPLACEMENT OF THE DRIVERS FRONT AIRBAG CLOCK SPRING ASSEMBLY ON THE 2011-2015 MY SORENTO VEHICLES, MANUFACTURED FROM 10/24/2009 THROUGH 12/17/2014. THE CLOCK SPRING IS AN ELECTRICAL CONNECTION WHICH ROTATES WITH THE STEERING WHEEL TO MAINTAIN PROPER FUNCTIONING OF THE AIRBAG UNIT. KIAS SYSTEM IS DESIGNED TO ILLUMINATE THE AIRBAG WARNING LIGHT WHEN ELECTRICAL RESISTANCE INCREASES, WHICH CAN BE CONTRIBUTED TO BY USAGE PATTERNS AND ENVIRONMENTAL CONDITIONS. ILLUMINATION OF THE AIRBAG WARNING LIGHT ADVISES THE DRIVER TO HAVE THE SYSTEM INSPECTED AND REPAIRED. IF CONTINUED TO BE USED WITHOUT REPAIR, THE DRIVERS AIRBAG MAY EVENTUALLY NOT DEPLOY IN A FRONTAL IMPACT. KIA IS EXTENDING THE WARRANTY COVERAGE FOR THE DRIVERS FRONT AIRBAG CLOCK SPRING ASSEMBLY ON THE 2011-2015 MY SORENTO VEHICLES, MANUFACTURED FROM 10/24/2009 THROUGH 12/17/2014, TO FIFTEEN (15) YEARS WITH UNLIMITED MILEAGE, STARTING FROM THE DATE OF FIRST SERVICE. THIS WARRANTY EXTENSION ADDRESSES FAILURES OF THE DRIVERS FRONT AIRBAG CLOCK SPRING AS REPORTED BY SOME VEHICLE OWNERS, AS WELL AS THE DIAGNOSIS OF ANY CONCERNS RELATED TO THE AIRBAG WARNING LIGHT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
OWNER LETTER: WTY003 - DEAR KIA SORENTO OWNER: KIA IS EXTENDING THE WARRANTY COVERAGE FOR THE DRIVERS FRONT AIRBAG CLOCK SPRING ASSEMBLY TO 15 YEARS WITH UNLIMITED MILEAGE, STARTING FROM THE DATE OF FIRST SERVICE. THE CLOCKSPRING IS AN ELECTRICAL CONNECTION WHICH ROTATES WITH THE STEERING WHEEL TO MAINTAIN PROPER FUNCTIONING OF THE AIRBAG UNIT. KIAS SYSTEM IS DESIGNED TO ILLUMINATE THE AIRBAG WARNING LIGHT WHEN ELECTRICAL RESISTANCE INCREASES, WHICH CAN BE CONTRIBUTED TO BY USAGE PATTERNS AND ENVIRONMENTAL CONDITIONS. ILLUMINATION OF THE AIRBAG WARNING LIGHT, ADVISES YOU TO HAVE THE SYSTEM INSPECTED AND REPAIRED. IF CONTINUED TO BE USED WITHOUT REPAIR, THE DRIVERS AIRBAG MAY EVENTUALLY NOT DEPLOY IN A FRONTAL IMPACT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DEALER PARTS AND SERVICE MANAGER MEMO: WTY003 - KIA MOTORS AMERICA, INC. IS EXTENDING THE WARRANTY COVERAGE FOR THE DRIVERS FRONT AIRBAG CLOCK SPRING ASSEMBLY ON THE 2011-2015 MY SORENTO VEHICLES, MANUFACTURED FROM 10/24/2009 THROUGH 12/17/2014, TO FIFTEEN (15) YEARS WITH UNLIMITED MILEAGE, STARTING FROM THE DATE OF FIRST SERVICE. THE CLOCK SPRING IS AN ELECTRICAL CONNECTION WHICH ROTATES WITH THE STEERING WHEEL TO MAINTAIN PROPER FUNCTIONING OF THE AIRBAG UNIT. KIAS SYSTEM IS DESIGNED TO ILLUMINATE THE AIRBAG WARNING LIGHT WHEN ELECTRICAL RESISTANCE INCREASES, WHICH CAN BE CONTRIBUTED TO BY USAGE PATTERNS AND ENVIRONMENTAL CONDITIONS. ILLUMINATION OF THE AIRBAG WARNING LIGHT ADVISES THE DRIVER TO HAVE THE SYSTEM INSPECTED AND REPAIRED. IF CONTINUED TO BE USED WITHOUT REPAIR, THE DRIVERS AIRBAG MAY EVENTUALLY NOT DEPLOY IN A FRONTAL IMPACT.