Original record summaries, dates and identifiers for this model-year. Records 301–400 of 628, ordered newest first. Dated records on this page: Feb 16, 2023–Sep 20, 2023.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Sep 20, 2023Service Bulletin/Repair Instructions
S2308000117
NHTSA communication ID: 10244410
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Engine Light On, P0CA6-00 Hybrid/EV Battery Charging Current High
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pan and Filter, Transmission Oil For WL & JL PHEV transmission leaks inspect for leaks through the transmission case prior to ordering a gasket. Leaks can be caused by possible porosity of transmission case or Oil Cooler Lines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pan and Filter, Transmission Oil For WL & JL PHEV transmission leaks inspect for leaks through the transmission case prior to ordering a gasket. Leaks can be caused by possible porosity of transmission case or Oil Cooler Lines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PUMP Water For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PUMP Water For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:COOLING SYSTEM:PUMP.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Switch-Mirror Before replacing this Switch, please follow the service procedures to properly diagnose it 1) Remove the switch 2) Please check the continuity on each pin of the switch based on the table found in the service Procedures. If after testing switch is still faulty, please call FCA Redacted Content. If no response after 15 minutes, proceeds with switch replacement.
Source components: ELECTRICAL SYSTEM · VISIBILITY:REARVIEW MIRRORS/DEVICES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Switch-Mirror Before replacing this Switch, please follow the service procedures to properly diagnose it 1) Remove the switch 2) Please check the continuity on each pin of the switch based on the table found in the service Procedures. If after testing switch is still faulty, please call FCA Redacted Content. If no response after 15 minutes, proceeds with switch replacement.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING:POSITION/LIMIT SENSOR/SWITCH.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Cluster Message ?Electric Mode Unavailable Cabin Heating or Cooling? or ?Electric Mode Temporarily Unavailable?, Vehicle Engine Runs All -the Time Does Not Enter Electric Vehicle (EV) Mode, Diagnostic Trouble Codes (DTCs) P0E15, U1008-00,U1124-00
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Defroster Inoperative Customer may experience the following: ? Rear window is not defrosting ? The rear window glass left or right side defrost solder terminal is detached from the defrost grid. This bulletin involves replacing the Electric Backlite (EBL) wire connector repair and re-securing the electrical connector(s) to the rear window.
Source components: ELECTRICAL SYSTEM · VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:REAR WINDOW.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
NHTSA source summary · Original PDF not reviewed by Recallfolio
ELECTRIC HYDRAULIC POWER STEERING PUMP Prior to replacing this component for damage at the pump electrical connection, please contact FCA redacted content. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Brake Vacuum Pump For DTC Code P258B. Due to brake vacuum pumps being returned with trouble not found, please follow the proper diagnostics outline in the service library this also includes checking all electrical and vacuum hose connections prior to replacement of the vacuum pump. This will avoid unnecessary repair and potential charge back on the vacuum pump.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES · SERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PUMP, Vacuum For DTC Code P258B - ELECTRONIC VACUUM PUMP PERFORMANCE. Due to brake vacuum pumps returned with trouble not found, please follow the proper diagnostics outline in the service library this also includes checking all electrical and vacuum hose connections prior to replacement of the vacuum pump. This will avoid unnecessary repair and potential charge back on the vacuum pump.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES · SERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Battery Pack Control Module (BPCM) Diagnostic and System Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ?P0A80-00 - Replace Hybrid/EV Battery Pack. ? P0EDD-00 - Contactor Wear Counter Far Advanced. In addition, the customer may comment on the following condition: ? Battery light on in the Instrument Panel Cluster (IPC). This bulletin involves updating the BPCM with the latest available software.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:PROPULSION SYSTEM:HYBRID MANAGEMENT · ELECTRICAL SYSTEM:PROPULSION SYSTEM:HYBRID MANAGEMENT:POWER CONTROL UNIT/MODULE (HPCU).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Hybrid Control Processor (HCP) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ?P0563-00 - System Voltage High. ? P2B28-00 - Hybrid/EV Battery Pack Coolant Pump Performance. Customers may also comment on one or more of the following: ? Reduced engine restart performance. ? May observe battery lamp illumination or the technician observes the 12V system voltage high when diagnosing. This bulletin involves reprogramming the HCP also known as Power Inverter Module (PIM) with the latest available software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fuel Filler Cap Tether Too Long Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ?P04EC - EVAP System Large Leak Detected - Fuel Tank Side. ? P04EE - EVAP System Very Small Leak Detected - Fuel Tank Side. Customers may also comment the following: ? There is a "Check Gas Cap" message in the Instrument Panel Cluster (IPC). NOTE: The above condition is caused from an air leak through the fuel filler cap and fuel filler neck seal, because the fuel filler cap tether is caught between both. This bulletin involves removing the fuel filler cap tether and replacing it with a shorter tether.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Integrated Dual Charging Module (IDCM) Enhancements Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) have been set: ? B22A9-64 - ECU Internal Performance-Signal Plausibility Failure. ? B22A9-16 - ECU Internal Performance-Circuit Voltage Below Threshold. ? B22A9-17 - ECU Internal Performance-Circuit Voltage Above Threshold. ? B22A9-19 - ECU Internal Performance-Overcurrent. Customer may also experience the following: ? Vehicle will not charge. This bulletin involves reprogramming the IDCM with the latest software available. NOTE: Additional module flashes are required for this update to be effective, the following modules are all to be updated along with this IDCM update: ? Powertrain Control Module (PCM). ? Integrated Dual Charging Module (IDCM). ? Transmission Control Module (TCM). ? Battery Pack Control Module (BPCM). ? Hybrid Control Processor (HCP), Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? **P02EE - Cylinder 1 Injector Circuit Performance. China only. ? P02EF - Cylinder 2 Injector Circuit Performance. China only. ? P02F0 - Cylinder 3 Injector Circuit Performance. China only. ? P02F1 - Cylinder 4 Injector Circuit Performance. China only.** ? P2B95 - Cold Start Injection Pulse Performance. ? P152E - Engine Hood Switch Two Circuit High. ? P152F - Engine Hood Switch Two Engine Hood Switch One Correlation. The customer may also comment on the following: ? ?Performance Limited Service Fuel System? message in the Instrument Panel Cluster (IPC). This bulletin involves reprogramming the PCM with the latest available software.
Source components: ELECTRICAL SYSTEM · POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Leak (Drips) On Center Stack, Radio Or Shifter Lever From The Front Center LH Freedom Panel Customers may comment on the following: ? Water is leaking on the radio coming from the left freedom top panel (Fig. 1) . This bulletin includes performing a water test and replacing foam pads on left hand freedom panel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engine Ticking Noise Engine makes an abnormal ticking noise. There may be Diagnostic Trouble Codes (DTC)s present. This bulletin involves inspecting and if needed, replacing the intake HLAs. NOTE: **ALL VEHICLES ON THE RSU VIN LIST REQUIRE ALL 12 INTAKE HYDRAULIC LASH ADJUSTERS TO BE REPLACED**.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mis-Installed 3-way Coolant Valve The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): ? P0E80-00 - Coolant Bypass Valve 9B9 Control Stuck Closed. Customer may also experience the following: ? Intermittent no heat. This bulletin involves possibly rerouting the three way valve hoses.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Leak - Liftgate Glass to Swing Gate Water leak into rear cargo area at the bottom of lift glass seal and top of swing gate. This bulletin involves installing two pieces of foam pads.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PSU right intake camshaft Case 1) If you are to flash the PSU (Pentastar Upgrade Engine) PCM due to P0300 code presence, only AB or previous LEVEL PSU right intake camshaft PN 05047913AA or AB (old version) should be replaced. If the engine is equipped with the AC/AD LEVEL PSU right intake camshaft PN 05047913AC or AD (new version), camshaft should NOT be replaced. Case 2) If the intake camshaft or intake rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).
Source components: ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ROCKER ARM ASSY - ROLLER ROCKER Case 1.- Before replacing the intake or exhaust rocker arms due to an abnormal ticking noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head (no need to replace rocker arms). The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. Case 2.- If the INTAKE camshaft or INTAKE rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engine Ticking Noise Engine makes an abnormal ticking noise. There may be Diagnostic Trouble Codes (DTC)s present. This bulletin involves inspecting and if needed, replacing the intake HLAs.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Anti-Lock Brake System (ABS) Module Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTC has been set: ? C2206-00 - Vehicle Configuration Mismatch. Customer may also experience one or more of the following: ? Inconsistent or unexpected brake performance is perceived in slow speed situations. ? Feels like the brake pedal needs to be pressed harder just before the vehicle comes to a stop (actual braking distance is not affected and driver is able to step further into the pedal for more brake pressure). This bulletin involves reprogramming the ABS with the latest software available.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Battery Charge Indicator (BCI) Replacement Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTC has been set: ? B1271-00 - Charge Level Indicator Internal. Customer may also experience the following: ? BCI does not indicate charge status while the vehicle is charging. This bulletin involves replacing the BCIM.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Re-Configure: Body Control Module (BCM) Customers may experience one or more of the following: ? Wi-Fi hotspot icon not shown in Uconnect. ? Wi-Fi functionality is missing from vehicle. This bulletin involves re-configuring the BCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Axle Assembly Do not replace the Axle for Axle Locker Sensor failure. The parts kit (SENSOR KIT, Axle: 68544629A$) must be used to repair the Axle Locker Sensor on JL/JT equipped with the M210 and M220 Tru-Lok axles (DSE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Updating to QR40.12 Software Version Mobile Wi-Fi inoperative upon start up. ? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Updating to QR40.12 Software Version Mobile Wi-Fi inoperative upon start up. ? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Wheel Hub and Bearing Before replacing the front or rear wheel hub and bearing for moaning, grinding, or groaning type noise, verify the noise is not coming from the transfer case. Follow the diagnostic procedure outlined in SOL Publication S2303000001 prior to any repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Integrated Dual Charging Module (IDCM) Replacement Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs have been set: ? B22A9-87 - ECU Internal Performance-Missing Message. Customer may also experience the following: ? Unable to charge the vehicle. This bulletin involves replacing the IDCM.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Integrated Dual Charging Module (IDCM) Replacement Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs have been set: ? B22A9-87 - ECU Internal Performance-Missing Message. Customer may also experience the following: ? Unable to charge the vehicle. This bulletin involves replacing the IDCM.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FILTER KIT, Transmission Oil For leak concerns that have been isolated to a transmission pan gasket, please replace ONLY the gasket. Pan/filter replacement are not required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FILTER KIT, Transmission Oil For leak concerns that have been isolated to a transmission pan gasket, please replace ONLY the gasket. Pan/filter replacement are not required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tail Lamp Water Intrusion The customer may experience the following: ? Water in the left and/or right tail lamp. This bulletin involves water testing the rear tail lamps and replacing if needed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tail Lamp Water Intrusion The customer may experience the following: ? Water in the left and/or right tail lamp. This bulletin involves water testing the rear tail lamps and replacing if needed.