2018 Jeep GRAND CHEROKEE Manufacturer communications & TSBs.Page 1
Original record summaries, dates and identifiers for this model-year. Records 1–100 of 446, ordered newest first. Dated records on this page: Feb 22, 2023–Sep 10, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Sep 10, 2026Service Bulletin/Repair Instructions
9100897Rev1
NHTSA communication ID: 11037351
NHTSA source summary · Original PDF not reviewed by Recallfolio
Qudra Lift Reman Compressor Excessive Repairs on Quadra Lift Reman Compressors Part Numbers: 68041137AF / R8572790AA / 68087233AA / 52124932AE / 52124934AE / 68064343AC Purpose The Star Parts Catalog has been updated to support component-level repair of the Quadra-Lift air suspension system. Replace only the component confirmed failed through diagnostics. Avoid replacing the complete assembly when an individual service component can correct the concern. Available Service Components Part Number Description R8572790AA Air Suspension Compressor 68087233AA Air Suspension Valve Block 52124932AE Front Air Suspension Hose Assembly 52124934AE Rear Air Suspension Hose Assembly 68064343AC Air Suspension Reservoir 68087240AA Temperature Sensor 68041137AF Compressor Assembly Diagnostic Decision Tree Customer Complaint: Service Air Suspension Message / Sagging / Unable to Adjust Ride Height / Compressor Running Continuously. Step 1: Retrieve and record all DTCs. C15D9 (Low Air Mass): Perform air mass test, complete system fill, leak-down test, and leak source identification before compressor replacement. C15A1 (Unable to Obtain Desired Ride Height): Verify ride height, perform leak-down test, inspect valve block, air lines, and air springs. C1562-98 (Over Temperature): Inspect for excessive compressor run time, leaks, low air mass, and restrictions before condemning the compressor. If a leak is found, repair the leak and verify operation before replacing the compressor. If no leak is found, perform compressor functional evaluation. If moisture is in the lines and valve block, then evacuate or replace lines. Only replace the compressor when a defect is verified (internal leak, failed solenoid, weak output, seized motor, failed functional test, or electrical failure). Service Component Selection Guide Verified Root Cause Recommended Repair Compressor Internal Failure Replace Compressor Valve Block Failure Replace Valve Block Air Line Leak Replace Air Line Air Spring Leak Replace Air Spring Temperature Sensor Failure Replace Temperature Sensor Technician Reminder Replace only the component confirmed failed through diagnostics. In many cases, compressor replacement is not required when the root cause is an air leak, valve block issue, airline concern, or sensor fault.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Qudra Lift Reman Compressor Excessive Repairs on Quadra Lift Reman Compressors Part Numbers: 68041137AF / R8572790AA / 68087233AA / 52124932AE / 52124934AE / 68064343AC Purpose The Star Parts Catalog has been updated to support component-level repair of the Quadra-Lift air suspension system. Replace only the component confirmed failed through diagnostics. Avoid replacing the complete assembly when an individual service component can correct the concern. Available Service Components Part Number Description R8572790AA Air Suspension Compressor 68087233AA Air Suspension Valve Block 52124932AE Front Air Suspension Hose Assembly 52124934AE Rear Air Suspension Hose Assembly 68064343AC Air Suspension Temperature Sensor 68041137AF Service Components Reference Diagnostic Decision Tree Customer Complaint: Service Air Suspension Message / Sagging / Unable to Adjust Ride Height / Compressor Running Continuously. Step 1: Retrieve and record all DTCs. C15D9 (Low Air Mass): Perform air mass test, complete system fill, leak-down test, and leak source identification before compressor replacement. C15A1 (Unable to Obtain Desired Ride Height): Verify ride height, perform leak-down test, inspect valve block, air lines, and air springs. C1562-98 (Over Temperature): Inspect for excessive compressor run time, leaks, low air mass, and restrictions before condemning the compressor. If a leak is found, repair the leak and verify operation before replacing the compressor. If no leak is found, perform compressor functional evaluation. If moisture is in the lines and valve block, then evacuate or replace lines. Only replace the compressor when a defect is verified (internal leak, failed solenoid, weak output, seized motor, failed functional test, or electrical failure). Service Component Selection Guide Verified Root Cause Recommended Repair Compressor Internal Failure Replace Compressor Valve Block Failure Replace Valve Block Air Line Leak Replace Air Line Air Spring Leak Replace Air Spring Temperature Sensor Failure Replace Temperature Sensor Technician Reminder Replace only the component confirmed failed through diagnostics. In many cases, compressor replacement is not required when the root cause is an air leak, valve block issue, airline concern, or sensor fault.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Active Diagnostic Trouble Code (DTC) B1A10-00, B1A11-00, B1A12- 00, B1A13-00-, B1A14-00, B1A15-00, B1A16-00, and B1A17-00 in The Radio Frequency Hub (RFH)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service transmission/check engine warning indicator for the 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV transmissions that have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0420 - Catalyst System Efficiency Below Threshold Bank 1. ● P0430 - Catalyst System Efficiency Below Threshold Bank 2. Customers may also experience the following: ● Catalyst damage and restricted exhaust flow, resulting in a reduction of engine power. This bulletin involves reprogramming the PCM with the latest available software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates *Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P0979-00 - Shift Solenoid 3 Control Circuit Low. ● P0219-00 - Engine Overspeed Condition. ● P0731-00 - Gear 1 Shift Incorrect Ratio. **Customers may experience the following: ● Shift shudder and shift shock during wide open throttle, high clutch energy shift.** The following software update is also included: ● Improved high RPM in coasting situations for the 1-2 shift This bulletin involves reprogramming the TCM with the latest available software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Drivetrain Control Module (DTCM) Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● C1403 - 92 Transfer Case Range Position Sensor - Performance Or Incorrect Operation. ● U0403 - 00 Implausible Data Received From Transfer Case. Customers may experience the following: ● Service 4WD Light On in Instrument Panel Control (IPC) This bulletin involves replacing the DTCM.Drivetrain Control Module (DTCM) Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● C1403 - 92 Transfer Case Range Position Sensor - Performance Or Incorrect Operation. ● U0403 - 00 Implausible Data Received From Transfer Case. Customers may experience the following: ● Service 4WD Light On in Instrument Panel Control (IPC) This bulletin involves replacing the DTCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order "68" part number for New unsold units only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
NHTSA source summary · Original PDF not reviewed by Recallfolio
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When replacing a camshaft and parts kit (P/N 68661146xx and/or 68661147xx), it is NOT necessary to order the roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADJUSTER Valve Lash Customer's complaint may include a ticking noise coming from the engine. Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Spark Knock/Engine Symptoms Customers may experience the following: ● Knocking or pinging noise coming from the engine upon acceleration. This bulletin involves cleaning the piston heads and cylinder head combustion chambers to resolve a spark knock condition being caused by oil intrusion through the PCV system."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Misfire Diagnostic Trouble Codes (DTCs), Rough Idle, Valvetrain Noise Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0301 - Cylinder 1 Misfire. ● P0302 - Cylinder 2 Misfire. ● P0303 - Cylinder 3 Misfire. ● P0304 - Cylinder 4 Misfire. ● P0305 - Cylinder 5 Misfire. ● P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: ● Rough idle. ● Valvetrain noise. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission "Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, visible ""glitter"" or debris in the pan and fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Touchscreen For all infotainment system repairs (touchscreens, radios, etc.), refurbished parts may be available. Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process
NHTSA source summary · Original PDF not reviewed by Recallfolio
"3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."
NHTSA source summary · Original PDF not reviewed by Recallfolio
FUEL PUMP/LEVEL UNIT MODULE For vehicles with Saddle Fuel Tanks, need to determine if there are any DTCs in wiTECH. Follow Service Diagnostics published prior to making any changes. Review any existing SOL or TSBs published for customer complaint issue. Only the Fuel Pump Module should be replaced if there are DTCs associated with the Fuel Level Sensor number 1. Only the Auxiliary Level Sender should be replaced if there are DTCs associated with the Fuel Level Sensor number 2. If there is a mixture of DTCs between the Fuel Pump Module and the Auxiliary Level Sensor, then investigate if there is a Jumper Harness or circuit issue between the Level Sender and the PCM. Verify fuel transfer between auxiliary tank and the primary tank by monitoring the auxiliary level sensor to verify it drops after driving.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
HEADREST Incoming Vehicles with Deployed Active Head Rest (AHR) should have a through enquiry. If there is no Broken Pieces or Electrical failure, Direction to follow the RESET Procedure in service Library to RESET the AHR
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"PUMP WATER For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PUMP Water For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PUMP Water For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:COOLING SYSTEM:PUMP.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0420 - Catalyst System Efficiency Below Threshold Bank 1. ? P0430 - Catalyst System Efficiency Below Threshold Bank 2. ? P0606 - Internal Control Processor. Customer may also experience the following: ? While the engine is running, customer may experience a vehicle limp in/home mode (speed limitation, engine throttle limitation and the ETC light flashing and MIL will be on) or the vehicle may experience a no-start condition. NOTE: Associated with DTC: P0606 - Internal Control Processor. This bulletin involves reprogramming the PCM with the latest available software.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? **P0441 - EVAP Purge System Performance.** ? P0456 - EVAP System Small Leak. NOTE: If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. ? P06EF - Engine Restart Performance. This bulletin involves reprogramming the PCM with the latest available software.
Source components: ELECTRICAL SYSTEM · POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Radio Frequency Hub Module (RFHM) Updates The customer may describe that they heard about these vehicles that can be unlawfully driven away by thieves when they are able to program new key fobs through the RFHM. Software enhancement include: ? Update to the RFHM software to prevent hackers from programming their own key fob to the vehicle. ? This is intended to deter an unwanted drive off of the vehicle without the customers knowledge.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.