2017 Jeep GRAND CHEROKEE Manufacturer communications & TSBs.Page 4
Original record summaries, dates and identifiers for this model-year. Records 301–352 of 352, ordered newest first. Dated records on this page: Mar 20, 2013–Jun 21, 2017.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jun 21, 2017Service Bulletin/Repair Instructions
9003357
NHTSA communication ID: 10138863
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pentastar Oil Filter Adapter All vehicles equipped with a 3.2L or 3.6L engine; If replacing the Oil Filter Adapter (OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fuel Tank Before replacing this part due to Hard to Fill condition, check the Fuel Filler Tube for restriction after the second door of the capless unit. Replace the Fuel Filler Tube if the second door of the capless unit does not open properly. Contact Sylvia Lopez at (248) 520-9734 if a Tank needs to be replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following software enhancements are available:Allow the throttle body to be cycled while the engine is off, for diagnostic purposes. Improved vehicle acceleration at low speed while towing. Allows transmission gear shifting while in limp-in mode, rather than a fixed gear.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) stored in the TCM memory:P1DCD-00 - TCM Monitoring Processor Performance Multiple Clutches Locked Up. In addition, customers may also experience the following condition:During an engine limp mode condition, the transmission remains in a fixed gear. This update allows transmission gear shifting while in limp-in mode, rather than a fixed gear. Bumps on 2-1 and 6-5 down-shift while braking. This software update also includes an enhancement:Improved 5-4 down-shift.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following software enhancements are available:Allow the throttle body to be cycled while the engine is off, for diagnostic purposes. Improved vehicle acceleration at low speed while towing. Allows transmission gear shifting while in limp-in mode, rather than a fixed gear.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) stored in the TCM memory:P1DCD-00 - TCM Monitoring Processor Performance Multiple Clutches Locked Up. In addition, customers may also experience the following condition:During an engine limp mode condition, the transmission remains in a fixed gear. This update allows transmission gear shifting while in limp-in mode, rather than a fixed gear. Bumps on 2-1 and 6-5 down-shift while braking. This software update also includes an enhancement:Improved 5-4 down-shift.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear View Camera In the case for inoperative camera, radio screen is blue or black in reverse mode. Before proceeding with the normal procedure call Ali Ikram at (248) 576-9265 Mon- Fri between 8 am- 4pm. If you do not get a response within 15 minutes continue with the repair. Make sure that connector is inserted properly. If there is a need to replace camera. In case of bad wire harness. Replace the harness and have it sent back to QEC.
Source components: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Brake Pedal Sensor For vehicles with DTC's P0572 or C0042, or complaints of brake lights staying on or cruise control not setting, please use wiTech to check the Brake Pedal Home Position setting and actual pedal resting position under brake pedal status in the ABS module. Before replacing the Brake Pedal Position Sensor, please call Rick Gordon at Cell (248) 630-6281. If no response within 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Blind Spot Detection Sensor If you are replacing this part due to a customer complaint of "Blind spot alert unavailable - wipe rear bumper", please read the following instructions before proceeding. 1) Verify that the rear bumper is clear of any obstructions. The process to clear the blockage message involves first cycling the ignition. 2) The vehicle must be driven on the road and pass/be passed by vehicles on both the left and right sides. After completing those steps, the blockage message will clear and the system will function as designed. Please call Zaid Almasarweh (586) 258-6771 if the previous steps do not correct the problem. If there is no response within 15 minutes, please continue with your normal diagnostic process.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM:ADAS:BLINDSPOT:SENSORS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear View Camera In the case for inoperative camera, radio screen is blue or black in reverse mode. Before proceeding with the normal procedure call Ali Ikram at (248) 576-9265 Mon- Fri between 8 am- 4pm. If you do not get a response within 15 minutes continue with the repair. Make sure that connector is inserted properly. If there is a need to replace camera. In case of bad wire harness. Replace the harness and have it sent back to QEC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Brake Pedal Sensor For vehicles with DTC's P0572 or C0042, or complaints of brake lights staying on or cruise control not setting, please use wiTech to check the Brake Pedal Home Position setting and actual pedal resting position under brake pedal status in the ABS module. Before replacing the Brake Pedal Position Sensor, please call Rick Gordon at Cell (248) 630-6281. If no response within 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Blind Spot Detection Sensor If you are replacing this part due to a customer complaint of "Blind spot alert unavailable - wipe rear bumper", please read the following instructions before proceeding. 1) Verify that the rear bumper is clear of any obstructions. The process to clear the blockage message involves first cycling the ignition. 2) The vehicle must be driven on the road and pass/be passed by vehicles on both the left and right sides. After completing those steps, the blockage message will clear and the system will function as designed. Please call Zaid Almasarweh (586) 258-6771 if the previous steps do not correct the problem. If there is no response within 15 minutes, please continue with your normal diagnostic process.
Source components: LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience the following condition: During an engine limp mode condition, the transmission remains in a fixed gear.The following software enhancement is also available: Transmission shift quality enhancement.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: U1424 - Implausible Engine Torque Signal Received (2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only).In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only).Other enhancements included in this update: Improved knock sensor performance.
Source components: AIR BAGS · BACK OVER PREVENTION · ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience the following condition: During an engine limp mode condition, the transmission remains in a fixed gear.The following software enhancement is also available: Transmission shift quality enhancement.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: U1424 - Implausible Engine Torque Signal Received (2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only).In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only).Other enhancements included in this update: Improved knock sensor performance.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Trans Pan or Gasket If your repair requires replacing one of the two part numbers for a leak, prior to the repair please call Enzo Piazza at cell (248) 467-9163. If you cannot reach Enzo within 15 minutes proceed with the repair. Enzo needs to know the location of the leak, if the bolts were torqued, if there is sealer skip, or anything that may be pertinent to the cause of the leak. Photos would be very helpful and can be sent to Enzo's cell phone or his email. Enzo's e-mail address is enzo.piazza@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Electric Power Steering Gear If any of the following DTCs exist, it is okay to replace the steering gear: C2217-00, C15C1-00 (EPS Mechanical Performance) or C15DB-00 (Latch Active) otherwise perform the following; 1) Electrical, Communication or DTC (other then above) issue please contact: Terry Gavit @ cell (248) 882-6108 terry.gavit@fcagroup.com Engineering is requesting a copy of Vehicle Scan Report (VSR) to be emailed to the above address. 2) Noise or Mechanical issue please contact: Ruth Delong @ cell (810) 569-0354.~ If you do not receive a return call within 15 minutes, proceed with the repair.~ Please be sure to attach a copy of the Vehicle Scan Report on the repair order
Source components: BACK OVER PREVENTION · POWER TRAIN · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
Source components: STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Trans Pan or Gasket If your repair requires replacing one of the two part numbers for a leak, prior to the repair please call Enzo Piazza at cell (248) 467-9163. If you cannot reach Enzo within 15 minutes proceed with the repair. Enzo needs to know the location of the leak, if the bolts were torqued, if there is sealer skip, or anything that may be pertinent to the cause of the leak. Photos would be very helpful and can be sent to Enzo's cell phone or his email. Enzo's e-mail address is enzo.piazza@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Electric Power Steering Gear If any of the following DTCs exist, it is okay to replace the steering gear: C2217-00, C15C1-00 (EPS Mechanical Performance) or C15DB-00 (Latch Active) otherwise perform the following; 1) Electrical, Communication or DTC (other then above) issue please contact: Terry Gavit @ cell (248) 882-6108 terry.gavit@fcagroup.com Engineering is requesting a copy of Vehicle Scan Report (VSR) to be emailed to the above address. 2) Noise or Mechanical issue please contact: Ruth Delong @ cell (810) 569-0354.~ If you do not receive a return call within 15 minutes, proceed with the repair.~ Please be sure to attach a copy of the Vehicle Scan Report on the repair order
NHTSA source summary · Original PDF not reviewed by Recallfolio
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Poor Vehicle Acceleration This bulletin involves test driving the vehicle and if required, replacing the fuel pump module. The customer may notice the vehicle has poor acceleration and/or the transmission will not upshift under Wide Open Throttle (WOT). This can be caused by low fuel flow from the fuel pump module.
Source components: FUEL SYSTEM, GASOLINE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Shock Absorber Customer complains of noise; this may be due to contact between shock body and the dirt shield. Please check dirt shield, if it is creating a rub mark remove but do not disassemble. Please call Robert Beckwith cell (248)-727-3689. If you don?t receive a response within 15 minutes, please continue with normal repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
NHTSA source summary · Original PDF not reviewed by Recallfolio
Poor Vehicle Acceleration This bulletin involves test driving the vehicle and if required, replacing the fuel pump module. The customer may notice the vehicle has poor acceleration and/or the transmission will not upshift under Wide Open Throttle (WOT). This can be caused by low fuel flow from the fuel pump module.
Source components: FUEL SYSTEM, GASOLINE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Shock Absorber Customer complains of noise; this may be due to contact between shock body and the dirt shield. Please check dirt shield, if it is creating a rub mark remove but do not disassemble. Please call Robert Beckwith cell (248)-727-3689. If you don?t receive a response within 15 minutes, please continue with normal repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
NHTSA source summary · Original PDF not reviewed by Recallfolio
Cleaner For A/C Evaporator Before using deodorizer to remove HVAC or evaporator odor, call Ken Deneau at cell (248) 765-0288. If no response in 15 minutes, please continue with repair
NHTSA source summary · Original PDF not reviewed by Recallfolio
Cleaner For A/C Evaporator Before using deodorizer to remove HVAC or evaporator odor, call Ken Deneau at cell (248) 765-0288. If no response in 15 minutes, please continue with repair
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience the following condition: · During an engine limp mode condition, the transmission remains in a fixed gear. The following software enhancement is also available: · Transmission shift quality enhancement.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: U1424 - Implausible Engine Torque Signal Received (2017 MY 3.0L and 3.6L Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only). In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only). Other enhancements included in this update: Improved knock sensor performance.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience the following condition: · During an engine limp mode condition, the transmission remains in a fixed gear. The following software enhancement is also available: · Transmission shift quality enhancement.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: U1424 - Implausible Engine Torque Signal Received (2017 MY 3.0L and 3.6L Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only). In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only). Other enhancements included in this update: Improved knock sensor performance.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Variable Valve Timing (VVT) Solenoid, Variable Valve Timing (VVT) Phaser For a 2016/2017 MY 6.4L SRT with less than 12,000 miles that have either a P0016 CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT - BANK 1 SENSOR 1 or P000B BANK 1 CAMSHAFT 2 POSITION SLOW RESPONSE fault codes active and fault code diagnostics lead to replacing a Variable Valve Timing (VVT) Solenoid and/or a Variable Valve Timing (VVT) Phaser, prior to changing any components, please contact Mr. CJ Maines at cell: (248) 576-0725 or email to: charles.maines@fcagroup.com. Engineering is seeking information on the above concern in an effort to root cause to this issue. If possible, please inquire about the last oil change date, miles and type used prior to calling. If the dealer is located in the Detroit Metro Area, Engineering may send a rep to review with technician. Any information is appreciated. If a response is not received within 15 minutes, then proceed with the necessary repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only).In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only).Other enhancements included in this update: Improved knock sensor performance.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Blind Spot Monitor System Improvements This bulletin involves updating the Left and Right Blind Spot Sensor (LBSS/RBSS) software. The customer may experience the blind spot monitor indicator may not chime alerting them that there is an object next to the vehicle.
Source components: LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
License Lamp If vehicle comes in for license plate bulb replacement, you will need to determine the version of the bulbs that you have. ~ ~ If you have clear lenses with lines on them, you will need PN 68225282AA. If none are available, you will need to order PN 68360246AA (Non-Camera) or 68360247AA (Camera).~ ~ If you have opaque lenses, you will only need PN 68228927AA
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Pump Dealers are replacing water pumps because of a coolant leak. Water pumps are found TNF but the water pump bypass o-ring was pinched resulting in a coolant leak that looks like a failed pump. Please inspect the bypass o-ring before replacing the pump as it is available separate for service.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Incorrect Gap Tolerance Between The Liftgate And Left Tail Lamp This bulletin involves removing excess sealant from the body behind the tail lamp to open the gap clearance between the left tail lamp and the liftgate. .1 - Gap Clearance Too Close (Left Side)1 - Proper Gap Clearance (Right Side)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PSU Exhaust Phaser 05048043AB If replacing the Exhaust Phaser for the following codes: P0340 Cam Missing/Camshaft Sensor Circuit and/or P0345 Cam Missing/Camshaft Sensor Circuit Engineering is requesting that all three Valve Timing components (Phaser, Actuator, OCV) be replaced.~ Please label the components of which bank they came from prior to parts return. ~ Phaser 05048043AB Actuator 05048045AB OCV 05048044AB Please call Joe Lovell at cell (734) 309-6467 with any questions If a response is not received within 15 mins , then proceed with diagnostics/repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Intake Manifold Gasket Intake Manifold Gaskets on Pentastar Upgrade (Sales Code ERC/ERF) are reusable provided they are not cut, torn or melted. The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.
NHTSA source summary · Original PDF not reviewed by Recallfolio
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~