Original record summaries, dates and identifiers for this model-year. Records 101–200 of 373, ordered newest first. Dated records on this page: Jul 15, 2024–May 29, 2025.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
May 29, 2025Service Bulletin/Repair Instructions
14-010-25 REV. A
NHTSA communication ID: 11018863
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Frequent Repairs Of Fuel Line Components Such As Fuel Filters Numerous Stellantis vehicles having fuel line components replaced such as fuel filter. Occasionally, components are replaced before their standard life expectancy or when not contaminated with debri "
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underhood start/stop safety The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): - P152E Engine -Hood Switch 2 Circuit High. - DTC P152F Customers may also experience: - Start/Stop system warning light. - Start/Stop inoperable. - Remote start inoperable. Diagnosis: - Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/Service Library, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the one listed are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin. - If any vehicle exhibits any of the symptoms listed above in the customer symptom section, perform the Repair Procedure. - Special Tools/Equipment: wiTECH or equivalent. Repair Procedure: 1. Open the hood and locate the hood switch 2. Push in on the two locking tabs and pull them out. 3. Disconnect the wire connector from the switch. 4. Connect the wires to the same hood switch. 5. Push the switch back into the hold until both lock tab are engaged. 6. Clear all DTCs that may have been set in any module during this repair procedure. 7. In case the P152F/P152E DTCs persist, repeat the procedure with a new/spare/known good switch and repeat steps 5 and 6. 8. Replace switch installed during previous step for the original switch of the vehicle. If DTCs P152F/P152E are not present, leave the original switch installed and do not document the change of the switch in the repair process/narrative.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Misfire Diagnostic Trouble Codes (DTCs), Rough Idle, Valvetrain Noise Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0301 - Cylinder 1 Misfire. ● P0302 - Cylinder 2 Misfire. ● P0303 - Cylinder 3 Misfire. ● P0304 - Cylinder 4 Misfire. ● P0305 - Cylinder 5 Misfire. ● P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: ● Rough idle. ● Valvetrain noise. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Transmission Fluid Please note fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Visible ""glitter"" or debris in the pan does not justify complete unit replacements."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission "Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, visible ""glitter"" or debris in the pan and fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Global Telematics Box Module (TBM) Firmware Over The Air (FOTA) Update 2023 - 2025 (JL) Jeep Wrangler 2023 - 2025 (JT) Jeep Gladiator This bulletin applies to vehicles built on or before May 05, 2025 (MDH 0505XX) equipped with Global Telematics Box Module (TBM) (Sales Code RDG). This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from 5.15, 5.41 or 5.43 to 5.53 software level"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Drag Link Long Socket FOR STEERING SHIMMY DIAGNOSIS, PLEASE REFERENCE S1819000004 Rev. Q AND 19 - Steering / Diagnosis and Testing (IN SERVICE LIBRARY). PLEASE REFER 19 - Steering / Linkage / END, Tie Rod / Diagnosis and Testing IF YOU HAVE BALL JOINT LOOSENESS CONCERN. PLEASE DO NOT REPLACE DRAG LINK AND TIE ROD UNLESS PART HAS VISIABLE DAMAGE OR FREE PLAY EXCEEDS SPECS."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Telematics Box Module Verify Z part number availability. Order a Z part number for all Exchange Orders: warranty, Mopar, customer pay and service contract. Order regular part number for New unsold units only."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"850RE D Clutch Repair **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Camshaft Sensor DTC Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0341 - Camshaft Position Sensor - Performance Bank 1 - Sensor 1. This bulletin involves repairing the cam sensor harness and re-routing the generator wiring."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P1DB7-00 - Torque Converter Clutch Performance. Customers may also experience one or more of the following: ● The check engine light illuminates. ● Overheating of the transmission fluid. This bulletin involves reprogramming the TCM with the latest available software."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Kit For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P1DB7-00- Torque Converter Clutch Performance. Customers may also experience one or more of the following: ● The check engine light illuminates. ● Overheating of the transmission fluid. REPAIR SUMMARY: This bulletin involves reprogramming the TCM with the latest available software."
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Oil Leaking From Oil Filter Area Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may comment on the following: ● Oil found on the ground beneath the vehicle. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses. "
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Clutch Overheat, And/Or Service Transmission Illuminated. Diagnostic Trouble Code (DTC) P08A6 – Gear Lever Position Sensor System – Multiple Sensor Correlation, Set Only In 4Low.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch"
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule. If the Filter is restricted or blocked then replace the part.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Drag Link Long Socket FOR STEERING SHIMMY DIAGNOSIS, PLEASE REFERENCE S1819000004 Rev. Q AND 19 - Steering / Diagnosis and Testing (IN SERVICE LIBRARY). PLEASE REFER 19 - Steering / Linkage / END, Tie Rod / Diagnosis and Testing IF YOU HAVE BALL JOINT LOOSENESS CONCERN. PLEASE DO NOT REPLACE DRAG LINK AND TIE ROD UNLESS PART HAS VISIABLE DAMAGE OR FREE PLAY EXCEEDS SPECS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
We have observed that some JL/JT rear axle shafts are leaking oil. Replace axle shaft and seal together. Do not replace seal only. Keep original seal and axle shaft and send the parts as fast track.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Fuel Delivery Module Inspection And Fuel Tank Replacement Customers may experience the following: ● Fuel gage reading incorrectly at 7/8 full after refueling. This bulletin involves replacing the fuel tank and possibly the fuel delivery module"
Source components: ELECTRICAL SYSTEM · FUEL/PROPULSION SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"B-Pillar Water Leak When Vehicle Is Parked On A Hill Customers may experience one or more of the following: ● The vehicle will leak water from the top of the B-pillar when the vehicle is parked on a downward incline. ● Water on door trim or carpet. ● Water drips down the inside door and panel This bulletin includes performing a water test and possibly adding foam pads to both Freedom Panels."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch"
NHTSA source summary · Original PDF not reviewed by Recallfolio
Heated Steering Wheel Jl/JT Heating Steering Wheel INOP or not warm enough The purpose of this document is to help dealerships root cause or diagnose the issue of the heated steering wheel system. Before replacing or ordering replacement parts (steering wheel, switches and wire harness) because of Heated Steering Wheel Inoperative And Or Not Hot Enough concern please review Star On Line S2423000045 for further details
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses."
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Noise From Front End While Driving Customers may experience the following: ● Noise (rattle/thump/clunk noise) coming from the front end of the vehicle. This bulletin involves inspecting and possibly replacing the Active Stabilizer Bar System (ASBS). "
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."
NHTSA source summary · Original PDF not reviewed by Recallfolio
CAN Star Block Connector Customer finds MIL light on and technician finds DTC for loss of communication on one or more modules. In repair procedure the dealerships are replacing the CAN star block connector during their root cause process with returned parts showing no trouble found. Here is a list of steps the dealers can follow to determine if they have a defective CAN star block connector using a multimeter: Step 1: Visually review CAN star block for damage and ensure back cover has all locking tabs engaged. If a bent pin, cracked or damaged housing or locking tab is not engaged is observed then replacement is required. Step 2: Identify Connector #1 as the 3 Pin Connector cavity Step 3: Measure resistance between Pin#1 and Pin#2 in Connector #1. Acceptable values are 120.4 Ohms to 139.8 Ohms. If resistance is outside of this range then replacement is required. Step 4: Measure the continuity between Pin#1 in Connector #1 to Pin#1 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required. Step 5: Measure the continuity between Pin#2 in Connector #1 to Pin#2 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
D Clutch Repair Kit TSB 21-039-24 REV A - D-Clutch repair kit missing Carrier Output Shaft Seals It has been identified the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits
NHTSA source summary · Original PDF not reviewed by Recallfolio
D Clutch Repair Kit TSB 21-039-24 REV A - D-Clutch repair kit missing Carrier Output Shaft Seals It has been identified the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits.