Original record summaries, dates and identifiers for this model-year. Records 101–200 of 334, ordered newest first. Dated records on this page: Jul 16, 2021–May 21, 2024.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
May 21, 2024Service Bulletin/Repair Instructions
9100338REV1
NHTSA communication ID: 11000824
NHTSA source summary · Original PDF not reviewed by Recallfolio
"GENERATOR Engine Prior to alternator/generator removal: 1. Inspect & check all electrical connections to the alternator a. 2-way connector containing field control circuit & alternator sense voltage circuit. b. Unplug & plug-in the 2-way connector for field & sense circuit. Verify the connection is tight & check for any bent pins in alternator connector or damage to female terminals in connector. c. Check Alternator B+ Stud connection to be sure nut is securing positive cable terminal properly (i.e. nut is clamping terminal & connection is tight). d. Check fuse between the alternator B+ stud & PDC terminal to make sure it is not blown. e. Be sure to follow service manual sections on ALTERNATOR CONTROL CIRCUIT DIAGNOSTIC & ALTERNATOR SENSE CIRCUIT DIAGNOSTIC looking for any opens & shorts (to ground or battery voltage). 2. Check/verify all grounds in the charging system circuit a. Check tightness of mounting bolts securing alternator to engine block. Alternator is a case ground component. b. Check main ground from engine to chassis; connection must be tight. c. Check battery ground cable connections are tight. d. Potentially, loosen alternator mounting bolts, without removing alternator, and re-tighten to torque specifications in service manual. e. After all steps above are complete, re-start engine & check charging system operation. 3. Verify that the Smart Charging System is not the reason for alternator low voltage & current output (Amps). a. Alternator charging can be suspended during engine idle operation because of the Smart Charge strategy. b. Refer to service manual section ""System Operation - Smart Charging System"". c. Refer to Star Case S2008000031 Rev A for low charging voltage & Smart Charge Mode Voltage Range diagram & mode descriptions. d. The alternator has no internal regulator; thus, has no smart circuitry. All alternator control signals come from ECM. 4. If alternator is faulty, remove alternator & mounting bolts. Return alternator with bolts for analysis at QEC."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Update from QR39.82F to QR40.12 Software Version Customer may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.82F to QR40.12. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Update from QR39.5 to QR40.11 Software Version Customer may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.5 to QR40.11. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Updating to QR40.12 Software Version Customers may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.2 to QR40.11. NOTE: National launch for this FOTA update is expected to begin February 19, 2023.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Update to Q339.3 to QR39.62 Software Version Customers may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from Q339.3 to QR39.62. NOTE: The National launch for this FOTA update campaign is expected to begin December 04, 2023.
Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC. · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
USB update to S27.10 for UTN radio - Japan The customer may describe one or more of the following: ? **Customer not receiving the map updates via the USB.** ? Menu for Active Lane Management is missing two settings, Lane Warning and Steering Assist Strength. This bulletin involves updating the radio software with USB to **S27.10.**
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Updating From QR39.6 to QR40.12 Software Version Customers may experience one or more of the following symptoms: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.6 to QR40.12. NOTE: National launch for this FOTA update is expected to begin November 06, 2023.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC. · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Global Telematics Box Module (TBM) Update to 4.34 The customer may experience the one or more of the following: ? Outdated vehicle data on customer's mobile app. ? Connected Services maintenance popup displayed on the radio screen. ? Connected Services battery maintenance popup displayed on the radio screen. This bulletin involves reprogramming the Global Telematics Box Module with the latest available software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Updating to QR40.12 Software Version ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.62 and QR39.57 to QR40.12. NOTE: National launch for this FOTA update is expected to begin August 16, 2023
NHTSA source summary · Original PDF not reviewed by Recallfolio
Paint Peeling on Front Bumper The customers may complain about paint peeling on the front bumper on vehicles with polar white color paint. This bulletin involves repainting the area of the front bumper that is peeling.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HEADLAMP WITHOUT BALLAST,If a replacement D5S BULB is needed, order the following: FOR North America D5S PART NUMBER: L0000D5S FOR Enlarged Europe XF D5S PART NUMBER: 71777147 FOR Enlarged Europe XP D5S PART NUMBER: 1609490380
NHTSA source summary · Original PDF not reviewed by Recallfolio
HEADLAMP WITHOUT BALLAST,If a replacement D5S BULB is needed, order the following: FOR North America D5S PART NUMBER: L0000D5S FOR Enlarged Europe XF D5S PART NUMBER: 71777147 FOR Enlarged Europe XP D5S PART NUMBER: 1609490380
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates Customers may experience the following: ? Vehicle repeatedly cranks when Engine Stop/Start (ESS) is active but engine doesn?t restart. Pushing switch, engine starts normally. This bulletin involves reprogramming the PCM with the latest available software.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Tail Lamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior tail lamp assemblies are fogged with a light layer of condensation on the inside of the lenses. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off, and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). This bulletin is to communicate the procedure for rear tail lamp condensation clearing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Body Control Module (BCM) Updates Customers may experience the following: ? The auto dimming does not work properly, the light intensity is very low. This bulletin involves reprogramming the BCM module with the latest available software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Updating to 40.12 Software Version Mobile Wi-Fi inoperative upon start up. Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 39.5 to 40.12.
NHTSA source summary · Original PDF not reviewed by Recallfolio
UAQ and UCQ Radio Enhancements Customers may experience one or more of the following: ? **Wi-Fi hotspot connection failure. ? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.
Source components: BACK OVER PREVENTION · EQUIPMENT:ELECTRICAL:INFOTAINMENT · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
Source components: STRUCTURE · STRUCTURE:INTERIOR PANELS:DOOR · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
An incorrect PDF document S228A000004 Rev. A - Panasonic VP4R Wi-Fi New Enrollment Pause was uploaded for this communication during publishing and was corrected with S228A000009 Rev. A
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of thefollowing DTCs have been set: P0031 - O2 Sensor 1/1 Heater Circuit Low. U0418-00 - Implausible Data Received From Brake System Control Module 1. Customers may experience the following: Long engine cranking prior to vehicle start more noticeable when the outsidetemperature is above 40 °c (104 °f).
Source components: ELECTRICAL SYSTEM · ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Drivetrain Control Module (DTCM) Updates This bulletin involves reprogramming the DTCM with the latest available software. The customer may describe the following: "4WD not available" on the Electronic Vehicle Information Center (EVIC) during harsh off road conditions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GEAR, Rack and Pinion If looking to replace the rack and pinion due to a clunking / knocking noise, please use the Chassis Ear Tool to pinpoint the exact location of the noise following the proper diagnostics. The points where you should place the chassis ear tool in sequence are: steering column, rack and pinion, intermediate shaft or the outer tie rod of the rack and pinion. Also ensure all related components are properly torqued such as shock absorbers, steering column, lower ball joints, stabilizer links, sway bar links and cradle mount bolts (front and rear). Please contact FCA Redacted Content for feedback related ONLY to this GPOP Tech Tip. Do Not email regarding repair procedures unrelated to this Tech Tip or part order inquiries.
Source components: BACK OVER PREVENTION · POWER TRAIN · STEERING · STRUCTURE · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
UAQ and UCQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to 39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth® pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BEV/Hybrid - Showroom and Display Vehicle Battery Maintenance This information only bulletin discusses procedures that must be followed for BEV/Hybrid vehicles that are on display at dealership showrooms.
Source components: ELECTRICAL SYSTEM · HYBRID PROPULSION SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may also experience the following: Harsh 1-2 or 2-3 upshifts.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.