Original record summaries, dates and identifiers for this model-year. Records 201–269 of 269, ordered newest first. Dated records on this page: Apr 29, 2014–Jun 29, 2016.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jun 29, 2016Service Bulletin/Repair Instructions
PC454
NHTSA communication ID: 10090652
NHTSA source summary · Original PDF not reviewed by Recallfolio
"ON FEBRUARY 26TH, INFINITI ANNOUNCED THAT IT WAS SENDING A REMINDER NOTIFICATION TO CLIENTS AFFECTED BY AT&TS PLANNED DISCONTINUATION OF THE 2G CELLULAR NETWORK. IN LATE SUMMER 2016, INFINITI PLANS TO PROVIDE FURTHER INFORMATION TO AFFECTED CLIENTS REGARDING OPTIONS TO HAVE THEIR TELEMATICS UNITS UPDATED. AT THIS TIME, INFINITI IS CONDUCTING A RETAILER INVENTORY SERVICE ACTION ON AFFECTED UNITS IN RETAILER INVENTORY TO REPLACE THE 2G-COMPATIBLE TELEMATICS CONTROL UNIT WITH A TELEMATICS CONTROL UNIT DESIGNED TO CONNECT TO THE AT&T 3G CELLULAR NETWORK. THE AFFECTED VEHICLES ARE EITHER CURRENTLY IN RETAILER INVENTORY OR ASSIGNED AND IN TRANSIT TO THE RETAILER. INFINITI REQUESTS THESE VEHICLES BE UPDATED PRIOR TO SALE TO ENABLE CLIENTS TO ACCESS AVAILABLE INFINITI CONNECTION FEATURES, INCLUDING AUTOMATIC COLLISION NOTIFICATION AND EMERGENCY CALLING. THERE ARE APPROXIMATELY 142 Q50 VEHICLES IN RETAILER INVENTORY THAT ARE EQUIPPED WITH TELEMATICS CONTROL UNITS DESIGNED TO CONNECT TO THE 2G CELLULAR NETWORK. HOWEVER, THE HARDWARE UPGRADE SERVICE PROCEDURE IS NOT AVAILABLE AT THIS TIME. PLEASE DO NOT TAKE ANY ACTION AT THIS TIME ON Q50 VEHICLES THAT ARE EQUIPPED WITH A 2G-COMPATIBLE TELEMATICS CONTROL UNIT. FURTHER INSTRUCTIONS WILL BE PROVIDED AT A LATER DATE FOR THE TCU UPGRADE ON AFFECTED Q50 VEHICLES. INFINITI EXPECTS THIS COMMUNICATION TO OCCUR IN LATE SUMMER 2016. IMPORTANT: RETAILERS SHOULD NOT SELL OR TRADE ANY AFFECTED VEHICLES IN RETAILER INVENTORY SUBJECT TO THIS SERVICE ACTION UNTIL THE 3G-COMPATIBLE TELEMATICS CONTROL UNIT HAS BEEN INSTALLED."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"INTELLIGENT KEY BATTERY VOLTAGE CHECK AND REPLACEMENT THIS BULLETIN HAS BEEN SUPERSEDED BY ITB15-026. INFINITI; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN."
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Temporary tire Flat Spotting is common on New Dealer In-Stock vehicles that have not been occasionally moved. Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90° (see Figure 1). Moving vehicles as shown in this bulletin will prevent tire Flat Spotting. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration) AND One of these DTCs is stored: - P17F0 (CVT_JUDDER (T/M INSPECTION)) - P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE - If a transmission judder (as described above) is not reported, this bulletin does not apply. - If either P17F0 or P17F1 are not stored, this bulletin does not apply. - ITB15-010, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTIONS: Perform the SERVICE PROCEDURE, starting on page 3. - Review the Repair Flow Chart on the next page. NOTE: Essential Tool Tech Cam (borescope) J-51951 has been sent to dealers. This tool?s attachments make CVT inspection possible. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location, ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Infiniti by request if certain criteria are met. This bulletinlists the criteria and provides an application form for such replacements. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IMPORTANT: Metal debris and friction material may become trapped in the radiator, cooling hoses, bypass valve or external CVT fluid cooler. This debris can contaminate the newly serviced transmission, control valve or torque converter. In severe cases this debris can block or restrict flow and may cause damage to the newly serviced CVT. SERVICE INFORMATION When a CVT, control valve or torque converter replacement is necessary for one of the applied vehicles, the CVT transmission fluid coolers (radiator based fluid cooler and external auxiliary cooler if present) must be flushed. Please see this bulletin for further details.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration). NOTE: A new diagnostic logic has been established to enhance the diagnostic process by storing diagnostic trouble codes (DTCs) on Applied Vehicles. The new DTCs are: P17F1 (CVT_JUDDER [C/U INSPECTION]) P17F0 (CVT_JUDDER [T/M INSPECTION]) ACTION 1. Refer to page 4, step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. NOTE: The current TCM Part Numbers in this bulletin have been updated. The vehicle you are working on may require reprogramming per this bulletin again. 2. If this bulletin applies, reprogram the TCM (Transmission Control Module See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM · POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The Service Procedure (starting on page 2) in this bulletin contains the steps to perform TCM Calibration Data Write Procedures. These procedures are used when a complete CVT is replaced, or a CVT control valve (valve body) is replaced, or a Transmission Control Module (TCM) is replaced. Please see this bulletin for further information.
Source components: ELECTRICAL SYSTEM · POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The MIL is ON with P0116 Engine Coolant Temperature (ECT SENSOR) stored, and There are no drivability issues. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm if ECM reprogramming applies. 2. If it applies, reprogram the ECM. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM While turning the steering wheel or when driving at low speed (straight or turning), a high pitch power steering noise can be heard. * Only while seated inside the vehicle And * With all of the windows up NOTE: If the audio and/or HVAC systems are turned ON it may be difficult to hear this issue. ACTION Install Insulator onto power steering oil pump assembly with Service Procedure starting on next page. Please see this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: Any one or a combination of the following after opening and/or closing a door (as it applies): * The auto headlights do not time out after the ignition is set to the OFF position. * The interior lights do not come ON. * Rogue only: The radio will not turn OFF after ignition is turned OFF. * The Vehicle Information Display in the combination meter showing "door ajar" when the doors are closed. * The Remote Engine Start feature is inoperative. ACTION: 1. Remove,and then reinstall, the screw of all four (4) door switches. 2. Confirm whichever issue has been occurring is resolved. NOTE: If the issue(s) is still not resolved, refer to ASIST and the appropriate Electronic Service Manual (ESM) for further diagnosis. Please see this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Beginning February 29th, owners of the affected Infiniti vehicles equipped with Telematics Control Units (TCU) will receive a letter notification explaining how their vehicle?s Infiniti Connection features will be affected by AT&T?s planned discontinuation of the 2G cellular network.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Occasionally customers may notice water vapor or fog in the headlamps. The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Infiniti?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The MIL is "ON" with DTC P0603 (ECM BACK UP/CIRCUIT). ACTION 1. Confirm that the battery voltage is 11 volts, or more, with the ignition ON (engine OFF, not running). 2. Erase DTC 3. Perform DTC confirmation steps in the Service Procedure. 4. Confirm 1st trip DTC P0603 is not stored. NOTE: P0603 is often the result of low battery voltage, discharged battery or battery terminal disconnections. Please see this bulletin for furtner details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION When diagnosing the front sonar parking sensor for potentially unwanted activation (e.g. sonar activates with no obstacle ahead), inspect the front license plate, front license plate frame and if equipped, the front license plate bracket. See page 2 for example photos. The front sonar parking sensor may activate if: The front license plate is bent outward from its bracket (there is a gap between the license plate and the bracket) OR the front license plate frame is bent or loose and is hanging outward, away from the license plate and/or bracket (there is a gap between the license plate frame and the license plate and/or bracket) OR the bracket is loose and is hanging outward, away from the bumper (there is a gap between the bracket and the bumper). If any of these conditions are found, correct it by removing the gap (straighten the license plate, straighten and/or secure the license plate frame, or secure the bracket, as it applies). - Retest the operation of the front sonar parking sensor. If the issue is not resolved, go to ASIST and the related Electronic Service Manual (ESM) for further diagnosis. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION On Applied Vehicles, the torque specification for the rear final drive assembly rear mounting stud has been revised. New torque specification: 71 N-m, 7.2 kg-m, 52 ft-lbs Use the torque specification shown above when installing a rear final drive assembly. At a later date and where possible, the applicable Electronic Service Manuals will be updated with the revised specification. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The function to detect the last item to trigger the vehicles theft alarm system can now be accessed with CONSULT-III plus (C-III plus). This function can be accessed by selecting: * Diagnosis (All Systems) or Diagnosis (One System). Then * BCM Then * THEFT ALM Then * Work Support Then * THEFT ALM TRG See this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The Intelligent Keys used on the various Infiniti vehicles may not be interchangeable between models and years. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The "shift lock cover" is now available as a separate part. If only the shift lock cover is needed, do not order the "Indicator Assy - Auto Transmission Control". Please see this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION: When the BCM in an APPLIED VEHICLE is being replaced for any reason, all existing Intelligent Keys must be re-registered. If new Intelligent Keys are added to the existing Intelligent Keys at the same time the BCM is being replaced, the procedure in this bulletin must be followed. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The tie down hook is no longer included with the jacking tools on 2015 QX60 vehicles, effective with the Applied Date and VIN shown above. Do not submit warranty claims for a missing tie down hook (a hook that was not originally supplied with the vehicle).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This activity will expire on December 18th, 2015. Retailers can continue to schedule and repair vehicles eligible for this service action until close of business December 18th, 2015. Claims will be honored for RO?s opened on or before the 18th of December.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Power moonroof initialization procedures for the Applied Vehicles have been revised. The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be initialized. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Design and process changes have been made to improve battery voltage at dealer receipt. Our goal is to deliver vehicles to customers with a 12 volt battery in excellent condition. Proper dealership storage and maintenance of vehicle 12 volt batteries is essential to insuring good battery operating life and customer satisfaction. Dealers are responsible for maintaining vehicles in their inventory. 12 volt batteries in vehicle inventory should always be kept at a full charge to prevent excessive discharge during storage and so they are ready for delivery to customers at any time. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM All "hands free" functions of the Intelligent Key (I-Key) do not work. For example, the doors will not lock or unlock when pressing either front door request switch. NOTE: - The issue of all I-Key "hands free" functions not working may occur intermittently or all the time. - The message "No Key Detected" or similar may show on the Vehicle Information Display (located in the combination meter). - All I-Key remote button functions (door lock/unlock, etc.) WILL work normally when all I-Key "hands free" functions are NOT working. ACTION 1. Inspect the I-Key?s battery on its negative contact side. 2. If excessive scratching is found, replace the battery. 3. Verify all I-Key functions (both "hands free" and remote) work properly after battery replacement. NOTE: Do NOT replace the BCM, I-Key, or other parts for the issue described under IF YOU CONFIRM, if it should occur. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION For Applied Vehicles, the rear door partition seals have been deleted. These seal are no longer a standard component and should not be considered missing and should not be installed. Do not submit a warranty claim for installation of a missing partition seal. Please see this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The customer states HomeLink will not operate or has improper operation. ACTIONS 1. To significantly reduce unnecessary repairs, make sure: a. The vehicle is not in "Transit Mode" (if equipped). - Not in Transit Mode: With the turn signal switch is in the OFF (center) position, turn the ignition from OFF to ON. If the turn signal indicators stay OFF (do not illuminate), the vehicle is not in Transit Mode. b. The "Extended Storage Switch" (if equipped) is in the "Customer Delivery" position (pushed in). - The Extended Storage Switch is located on the fuse block that is located in the interior of the vehicle. 2. Confirm the customer is familiar with the HomeLink programming procedure located in the vehicle?s owner?s manual. 3. Test HomeLink operation with special tool HomeLink Transmitter Tester J-41540. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM All of the following - The engine will not start (no crank; starter will not engage) when pushing the ignition switch, and I-Key Error message is displayed in the combination meter, and DTC B2604 (PNP/Clutch Switch) is stored, past or present. ACTION Perform adjustment of the shift control cable per the Service Procedure in this bulletin. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
Source components: BACK OVER PREVENTION · LANE DEPARTURE · SERVICE BRAKES · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INFINITI: AN INVENTORY INSPECTION FOR CERTAIN VEHICLES WAS CONDUCTED AND IS NO LONGER NECESSARY TO BE PERFORMED AND THE VEHICLES CAN NOW BE RELEASED. MODEL 2015 QX60. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: The rubber weatherstrips on either one of the roof side molding assemblies (moldings) is coming loose from the molding itself. ACTION: Replace both left and right moldings with the ones listed in PARTS INFORMATION. - Refer to SERVICE PROCEDURE for molding replacement. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Infiniti is conducting a retailer inventory inspection to inspect the right and left transverse link (TV) pivot bolt to ensure that the locking nut is present and torqued to the correct specification
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The information in this bulletin is provided to help ensure correct diagnosis and repair of fluid leaks. All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair. Unnecessary repair or replacement of parts in connection with incorrectly diagnosed "leaks" can negatively impact customer satisfaction, be time consuming and costly, and if not performed correctly can lead to future repairs. See this bulletin for further detail.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If the AV Control Unit needs to be replaced on an Applied Vehicle for any reason, follow the steps in the Service Procedure to configure the Multi AV system. NOTE - The original AV Control Unit must be installed in the vehicle while performing part of this procedure. DO NOT remove the original AV Control Unit until instructed. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INFINITI: ON SOME VEHICLES, THE FORWARD COLLISION WARNING (FCW) MALFUNCTION HAS BEEN OR IS ON AND FLUID LEVEL FOR BRAKES IS NORMAL AND THE ABS CONTROL UNIT NEEDS PROGRAMMING, PER SERVICE PROCEDURE. MODEL 2013-14 JX35, QX60, 2014-15 Q50. *PE UPDATED 9/10/15. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The Applied Vehicles are equipped with a new version of Intelligent Key presets memory. Each Intelligent Key can be programmed to have its own unique set of presets for certain vehicle systems. Vehicle systems that are linked with Intelligent Key include: - Automatic Drive Positioner (includes driver seat, steering column, and mirror position memory) - Audio (station presets, etc.) - Auto air conditioning and heating (retains the last temperature and mode setting for each Intelligent Key user) - Navigation system (retains the last settings [e.g., Birdview] and clock display preference for each Intelligent Key user) See this bulletin for further detail.
Source components: AIR BAGS · STEERING · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer are capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
Source components: BACK OVER PREVENTION · EQUIPMENT · SERVICE BRAKES · STEERING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Infiniti is conducting a retailer inventory inspection to inspect the right and left transverse link pivot bolt to ensure that the locking nut is present and torqued to the correct specification.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM There is a vibration or judder feeling from the rear of the vehicle when making turns on dry roads at low speeds (under 40 MPH), and it does not occur if the Electric Controlled Coupling is electrically disconnected. ACTION Replace the Electric Controlled Coupling for the rear final drive. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: The MIL is ON and any of the following DTCs are stored in the ECM: - P0037, P0038, P0057, P0058, P0139, P0159, P0141, P0161, P0137, P0157, P0138, P0158 ACTION: 1. Refer to step 6 in the SERVICE PROCEDURE to confirm if ECM reprogramming applies. 2. If it applies, reprogram the ECM. 3. Replace only the rear O2 sensor that relates to the stored DTC(s) (B1 and/or B2). NOTE: Do NOT replace both rear O2 sensors if the DTC(s) is for one rear O2 sensor. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION For vehicles delivered to the dealers with wheel protector covers - Do not remove the wheel protector covers during Pre-Delivery Inspection (PDI) - Wheel protector covers help prevent cosmetic rotor corrosion. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Infiniti vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle. The PGF protects the paint finish during vehicle handling, transportation and storage from harmful elements such as acid rain,iron particles, bird droppings, tree sap and other environmental contaminants. NOTE - Paint Guard Film CANNOT remain on the vehicle for more than six months after the vehicle's manufacture date. PGF must be removed at the end of six months. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2015 Infiniti QX60. A short section of the bulkhead seam under the passenger side A-Pillar was not completely sealed during vehicle production.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2015 Infiniti QX60. A short section of the bulkhead seam under the passenger side A-Pillar was not completely sealed during vehicle production.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INTRODUCTION Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2015 Infiniti QX60. A short section of the bulkhead seam under the passenger side A-Pillar was not completely sealed during vehicle production. This seam will be sealed at no charge for parts or labor. IDENTIFICATION NUMBER Infiniti has assigned identification number PC341 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. Please see this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Infiniti STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
Source components: AIR BAGS · BACK OVER PREVENTION · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.infinitinavigation.com and is mailed update disc(s) or SD card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If a customer would like to activate a subscription for any of the following services: - SiriusXM Satellite Radio, NavTraffic, NavWeather or Travel Link OR If a radio is replaced for any reason, and a customer has an active subscription to any of the above services, OR If a customer claims to have an active subscription to any of the above services, AND any portion of the subscribed service is not operating, ... follow the steps in this bulletin to activate/refresh the service.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If one or both Intelligent Keys cannot be located prior to customer delivery of an Applied Vehicle, refer to the applicable section of this bulletin for Intelligent Key registration instructions. - One (1) Intelligent Key Is Lost ----- Page 2 - Two (2) Intelligent Keys Are Lost ----- Page 3 See this bulletin for further detail.
Source components: COMMUNICATION: VEHICLE TO INFRASTRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Starting with 2010 Model Year, Infiniti vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION A two-piece design front engine mount is currently being used for the applied vehicles listed. A single thunk noise may be heard on the first acceleration of the day from this type of mount and is considered normal operation. The mount has also been designed with built in free-play that is normal. Under normal driving conditions: * A "thunk" noise may be heard on the first acceleration of the day. And * Does not occur again, or at any other time. DO NOT REPLACE THE MOUNT: * If it has free play or a "single event" thunk sound on the first acceleration of the day. This is considered a normal characteristic of this type of engine mount. * If a shift shock condition is present when shifting from park into gear or between any combination of gears. This condition is due to transmissions line pressures and not movement of the mount. NOTE: Refer to the Electronic Service Manual section TM - Transaxle & Transmission for further diagnostic information on shift shock. See this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Infiniti is conducting an inventory inspection on 5,809 specific 2014-15 Infiniti QX60 vehicles and requesting retailers perform a software check on the OCS ECU on specific vehicles identified in SERVICE COMM.
Source components: ELECTRICAL SYSTEM · ENGINE · ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Applied vehicles equipped with a CVT have a "cap" that appears to be a fluid level gauge. This "cap" will NOT have a gauge or "dipstick". This is normal. Do NOT replace the "cap" because it is thought to have a "dipstick". The fluid level is not checked from this location. The fluid level for applied vehicles is checked from the oil pan (refer to the appropriate section of the Electronic Service Manual (ESM)). Whenever checking, filling, or topping off a CVT's fluid level of an applied vehicle for any reason, use the procedure outlined in the appropriate section of the ESM. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The purpose of this bulletin is to clarify language contained in the owner?s manual language for the APPLIED VEHICLES. For the APPLIED VEHICLES, the below language supersedes similar language in existing owner?s manuals. Future printings of owner?s manuals for the APPLIED VEHICLES will also contain the below language. For the APPLIED VEHICLES: INFINITI recommends using Genuine NISSAN NS-3 CVT Fluid ONLY in INFINITI CVTs. Do not mix with other fluids. Do not use Automatic transmission fluid (ATF) or Manual Transmission fluid in an INFINITI CVT, as it may damage the CVT. Damage caused by the use of fluids other than as recommended is not covered under INFINITI's New Vehicle Limited Warranty. Using fluids that are not equivalent to Genuine NISSAN NS-3 CVT Fluid may also damage the CVT. Damage caused by the use of fluids other than as recommended is not covered under INFINITI's New Vehicle Limited Warranty. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Infiniti vehicles has changed. This bulletin gives an outline of the retailer technician?s responsibilities in assisting the retailer claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.