The manufacturer’s record · Page 5 of 8
Original record summaries, dates and identifiers for this model-year. Records 401–500 of 734, ordered newest first. Dated records on this page: May 1, 2011–Feb 21, 2014.
Back to 2005 Hummer H2 problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10138640
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.
Source components: VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR.
Source record 10138640 at NHTSANHTSA communication ID: 10138631
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on.
Source components: TIRES · WHEELS:RIM.
Source record 10138631 at NHTSANHTSA communication ID: 10111927
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · FUEL SYSTEM, GASOLINE · SERVICE BRAKES, HYDRAULIC.
Source record 10111927 at NHTSANHTSA communication ID: 10111894
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111894 at NHTSANHTSA communication ID: 10190932
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10190932 at NHTSANHTSA communication ID: 10190931
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10190931 at NHTSANHTSA communication ID: 10025705
NHTSA source summary · Original PDF not reviewed by Recallfolio
TIRE SLOWLY GOES FLAT, TIRE AIR LOSS, LOW TIRE PRESSURE WARNING LIGHT ILLUMINATED, ALUMINUM WHEEL BEAD SEAT CORROSION (CLEAN AND RESURFACE WHEEL BEAD SEAT) FOR CERTAIN 2000-2009 GM PASSENGER CARS AND LIGHT DUTY TRUCKS (INCLUDING SATURN). *PE UPDATED 04/15/2014 *JS
Source components: TIRES:BEAD · WHEELS.
Source record 10025705 at NHTSANHTSA communication ID: 10019584
NHTSA source summary · Original PDF not reviewed by Recallfolio
USE OF NITROGEN GAS IN TIRES. *AK 2015 AND PRIOR GM PASSENGER CARS & TRUCKS (INCLUDING SATURN) ALSO 2008 AND PRIOR HUMMER H2, H3, SAAB 9-7X. UPDATED 5/12/08. *NJ UPDATED 04/15/2014 *JS
Source components: TIRES.
Source record 10019584 at NHTSANHTSA communication ID: 10137784
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
Source components: EQUIPMENT.
Source record 10137784 at NHTSANHTSA communication ID: 10112013
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10112013 at NHTSANHTSA communication ID: 10111997
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
Source components: EQUIPMENT.
Source record 10111997 at NHTSANHTSA communication ID: 10137777
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
Source record 10137777 at NHTSANHTSA communication ID: 10137776
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Also during a 3-2 downshift, the releasing of the 3-4 clutch during the application of the 2-4 band, can cause torque reversal down the output shaft creating a clunk. This is a normal condition.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER · POWER TRAIN:CLUTCH ASSEMBLY.
Source record 10137776 at NHTSANHTSA communication ID: 10190934
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
Source record 10190934 at NHTSANHTSA communication ID: 10190933
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
Source record 10190933 at NHTSANHTSA communication ID: 10133103
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides directions on submitting different PIRs
Source components: BACK OVER PREVENTION: SENSING SYSTEM: RADAR.
Source record 10133103 at NHTSANHTSA communication ID: 10133097
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin explains physical damage to radios and IPCs must be reviewed and validated if covered under GM warranty or not.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10133097 at NHTSANHTSA communication ID: 10133086
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil additives.
Source components: FUEL SYSTEM, DIESEL · FUEL SYSTEM, GASOLINE · FUEL SYSTEM, OTHER.
Source record 10133086 at NHTSANHTSA communication ID: 10118842
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational Bulletin provides a revision for 10-08-110-001 to add the 2012-2014 model years.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10118842 at NHTSANHTSA communication ID: 10112331
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
Source components: ENGINE AND ENGINE COOLING.
Source record 10112331 at NHTSANHTSA communication ID: 10113227
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
Source components: EQUIPMENT.
Source record 10113227 at NHTSANHTSA communication ID: 10246631
NHTSA source summary · Original PDF not reviewed by Recallfolio
Expanded Availability for Remanufacture and Return (R&R) Electronic Control Modules
Source components: ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM).
Source record 10246631 at NHTSANHTSA communication ID: 10113502
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:APPLIANCE:AIR CONDITIONER · EQUIPMENT:ELECTRICAL · POWER TRAIN:AXLE ASSEMBLY · SERVICE BRAKES.
Source record 10113502 at NHTSANHTSA communication ID: 10113199
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.
Source components: ELECTRICAL SYSTEM.
Source record 10113199 at NHTSANHTSA communication ID: 10113483
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information new tire warranty program and global warranty management submission information.
Source components: TIRES.
Source record 10113483 at NHTSANHTSA communication ID: 10113177
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10113177 at NHTSANHTSA communication ID: 10130567
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on key codes security rules and information on GM key code look up application.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10130567 at NHTSANHTSA communication ID: 10130562
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on key code security and information on GM key code look up applications.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10130562 at NHTSANHTSA communication ID: 10113059
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
Source record 10113059 at NHTSANHTSA communication ID: 10134736
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision of 05-09-40-002F to add the 2013-2014 model years.
Source components: SEAT BELTS.
Source record 10134736 at NHTSANHTSA communication ID: 10134627
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical service bulletin provides a revision for 07-08-49-020G to add the 2014 model year and update model list.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL.
Source record 10134627 at NHTSANHTSA communication ID: 10139080
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for Disc Brake Warranty Service and Procedures.
Source components: EQUIPMENT · SERVICE BRAKES.
Source record 10139080 at NHTSANHTSA communication ID: 10139078
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for Automatic Transmission Oil Cooler Flow Test Essential Tool J-45096 TransFlow.
Source components: EQUIPMENT · POWER TRAIN.
Source record 10139078 at NHTSANHTSA communication ID: 10139067
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making.
Source components: EQUIPMENT.
Source record 10139067 at NHTSANHTSA communication ID: 10139066
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
Source record 10139066 at NHTSANHTSA communication ID: 10139059
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information.
Source components: EQUIPMENT.
Source record 10139059 at NHTSANHTSA communication ID: 10139057
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates.
Source components: EQUIPMENT.
Source record 10139057 at NHTSANHTSA communication ID: 10139052
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information.
Source components: EQUIPMENT · WHEELS.
Source record 10139052 at NHTSANHTSA communication ID: 10139049
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor Operation.
Source components: EQUIPMENT · VISIBILITY:WINDSHIELD.
Source record 10139049 at NHTSANHTSA communication ID: 10139043
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 13-00-89-004A to include updated information.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10139043 at NHTSANHTSA communication ID: 10139041
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 05-03-07-009E to add the 2014 model year and update the Labor Operations.
Source components: EQUIPMENT · WHEELS.
Source record 10139041 at NHTSANHTSA communication ID: 10139039
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 06-00-89-026J to add the 2014 model year and update the labor operations.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT.
Source record 10139039 at NHTSANHTSA communication ID: 10139036
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 09-07-30-018C to add the 2014 model year and update the Labor Operation.
Source components: EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10139036 at NHTSANHTSA communication ID: 10139024
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is a revision for 09-00-89-016B to add the 2014 model year and update the labor operation.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10139024 at NHTSANHTSA communication ID: 10113074
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · EQUIPMENT.
Source record 10113074 at NHTSANHTSA communication ID: 10130652
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides Warranty Administration - New Labor Codes information.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10130652 at NHTSANHTSA communication ID: 10130645
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision of 13-00-89-004 to update car issues information for reference information/bulletin PI0746C.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10130645 at NHTSANHTSA communication ID: 10130627
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10130627 at NHTSANHTSA communication ID: 10130619
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision of 10-00-89-017Z to include updated information.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10130619 at NHTSANHTSA communication ID: 10134681
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10134681 at NHTSANHTSA communication ID: 10134652
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on fix it right for first time issues.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10134652 at NHTSANHTSA communication ID: 10134640
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.
Source components: WHEELS.
Source record 10134640 at NHTSANHTSA communication ID: 10112885
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
Source components: EQUIPMENT.
Source record 10112885 at NHTSANHTSA communication ID: 10112857
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
Source components: ELECTRICAL SYSTEM.
Source record 10112857 at NHTSANHTSA communication ID: 10112842
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
Source record 10112842 at NHTSANHTSA communication ID: 10133130
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information pre-painting/cleaning process for TPO plastic fascias.
Source components: STRUCTURE:BODY.
Source record 10133130 at NHTSANHTSA communication ID: 10133125
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on a update for the Electronic Component Exchange Program (U.S. and Canada Only)
Source components: EQUIPMENT:ELECTRICAL.
Source record 10133125 at NHTSANHTSA communication ID: 10112697
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
Source components: EQUIPMENT:MECHANICAL · POWER TRAIN.
Source record 10112697 at NHTSANHTSA communication ID: 10112691
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that will no longer sit level after rear suspension has been serviced. Technician should correctly install the air spring lines that are incorrectly connected.
Source components: SUSPENSION:FRONT:SPRINGS:AIR SUSPENSION SYSTEM · SUSPENSION:REAR:SPRINGS:AIR SUSPENSION SYSTEM.
Source record 10112691 at NHTSANHTSA communication ID: 10113843
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10113843 at NHTSANHTSA communication ID: 10112664
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.
Source components: ELECTRICAL SYSTEM.
Source record 10112664 at NHTSANHTSA communication ID: 10112641
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
Source components: ENGINE AND ENGINE COOLING.
Source record 10112641 at NHTSANHTSA communication ID: 10113837
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10113837 at NHTSANHTSA communication ID: 10126163
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10126163 at NHTSANHTSA communication ID: 10138218
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats not
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM) · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10138218 at NHTSANHTSA communication ID: 10137476
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats not
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10137476 at NHTSANHTSA communication ID: 10112614
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers may inquire about the availability of the passenger compartment air filter. Dealer should advise the customer starting in 2003 the passenger compartment air filter is no longer available as a factory option.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10112614 at NHTSANHTSA communication ID: 10138217
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10138217 at NHTSANHTSA communication ID: 10137475
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
Source components: EQUIPMENT.
Source record 10137475 at NHTSANHTSA communication ID: 10126171
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
Source components: EQUIPMENT.
Source record 10126171 at NHTSANHTSA communication ID: 10112607
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
Source components: EQUIPMENT:ELECTRICAL · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10112607 at NHTSANHTSA communication ID: 10112600
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
Source components: POWER TRAIN:AXLE ASSEMBLY.
Source record 10112600 at NHTSANHTSA communication ID: 10126192
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10126192 at NHTSANHTSA communication ID: 10126196
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
Source components: EQUIPMENT.
Source record 10126196 at NHTSANHTSA communication ID: 10138197
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year.
Source components: ENGINE · EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION · SERVICE BRAKES.
Source record 10138197 at NHTSANHTSA communication ID: 10137454
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year.
Source components: EQUIPMENT.
Source record 10137454 at NHTSANHTSA communication ID: 10126200
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10126200 at NHTSANHTSA communication ID: 10126198
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.
Source components: EQUIPMENT.
Source record 10126198 at NHTSANHTSA communication ID: 10112560
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: SERVICE BRAKES.
Source record 10112560 at NHTSANHTSA communication ID: 10138192
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure for replacing the throttle position sensor cover for concerns regarding a indicator lamp illuminated reduced power message displayed and DTC P2135 set.
Source components: ELECTRICAL SYSTEM · ENGINE · EQUIPMENT · POWER TRAIN.
Source record 10138192 at NHTSANHTSA communication ID: 10137449
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure for replacing the throttle position sensor cover for concerns regarding a indicator lamp illuminated reduced power message displayed and DTC P2135 set.
Source components: ENGINE AND ENGINE COOLING.
Source record 10137449 at NHTSANHTSA communication ID: 10126203
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10126203 at NHTSANHTSA communication ID: 10112546
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
Source components: SERVICE BRAKES · SERVICE BRAKES, HYDRAULIC.
Source record 10112546 at NHTSANHTSA communication ID: 10112544
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a power steering pump whine noise. Technician will need to flush and refill the power steering system with Lucas Power Steering Fluid with Conditioners. Technician will replace the power steering pump with the latest design if the fluid is not available.
Source components: SERVICE BRAKES, HYDRAULIC:POWER ASSIST · STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID.
Source record 10112544 at NHTSANHTSA communication ID: 10112528
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
Source components: ELECTRICAL SYSTEM.
Source record 10112528 at NHTSANHTSA communication ID: 10112519
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have grease leaking from front hub bearings. Technician should not replace the bearing for grease purge. Technician should be advised to not clean the purged grease from the area immediately on or adjacent to the seals because this grease provides additional protection. Technician should only replace the bearing if the seals show visible damage, bearing endplay is greater than 0.005" or 0.13mm, bearing exhibits rough rotation, or bearing exhibits abnormal noise.
Source components: SUSPENSION:FRONT:HUB · WHEELS:HUB.
Source record 10112519 at NHTSANHTSA communication ID: 10112494
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10112494 at NHTSANHTSA communication ID: 10118637
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:OTHER:LABELS.
Source record 10118637 at NHTSANHTSA communication ID: 10118635
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure for relearning the power folding mirriors and road testin to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions.
Source components: VISIBILITY:REARVIEW MIRRORS/DEVICES.
Source record 10118635 at NHTSANHTSA communication ID: 10118634
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10118634 at NHTSANHTSA communication ID: 10084683
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS.
Source components: EQUIPMENT · STRUCTURE.
Source record 10084683 at NHTSANHTSA communication ID: 10118626
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10118626 at NHTSANHTSA communication ID: 10118619
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on newly release bulletins used to fi the vehicles in the field the first time.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10118619 at NHTSANHTSA communication ID: 10246951
NHTSA source summary · Original PDF not reviewed by Recallfolio
Programming And Activation Of Replacement OnStar Modules.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10246951 at NHTSANHTSA communication ID: 10037570
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: ON SOME TRUCK MODELS THERE IS SOME FRAME CORROSION. *RM UPDATED ON 5/2/2012. *KB
Source components: STRUCTURE:FRAME AND MEMBERS.
Source record 10037570 at NHTSANHTSA communication ID: 631244
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS VEHICLES AND TRUCKS: SUBJECT REGARDING, 2002 AND PRIOR PASSENGER CARS AND TRUCKS, CHEMICAL DAMAGE TO EXTERIOR POLYCARBONATE HEADLAMP LENSES. *SLC UPDATED *EH UPDATED 3/30/11. HEADLAMP LENS OVERHEATING WHEN COVERED AND CHEMICAL DAMAGE TO EXTERIOR POLYCARBONATE HEADLAMP LENSES. CAN CAUSE CRAZING OR CRACKING OF HEADLAMP LENS. *PE UPDATED 6/24/11. *PE UPDATED 5/14/12. INCLUDING 2013 MODEL YEAR. *PE
Source components: EXTERIOR LIGHTING:HEADLIGHTS.
Source record 631244 at NHTSANHTSA communication ID: 10038294
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE
Source components: SEAT BELTS · SEAT BELTS:FRONT:WARNING LIGHT/DEVICES.
Source record 10038294 at NHTSANHTSA communication ID: 10032332
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM/HUMMER/SAAB: INTERMITTENT ILLUMINATION OF MIL, SERVICE LAMPS, SERVICE MESSAGES, OR DTC SET BY VARIOUS CONTROL MODULES-DIAGNOSING AND REPAIRING FRETTING CORROSION (DISCONNECT AFFECTED CONNECTOR AND APPLY DIELECTRIC LUBRICANT). *PE UPDATED 3/26/10. *PE UPDATED 6/6/11. *PE UPDATED 3/12/12. *PE
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING.
Source record 10032332 at NHTSANHTSA communication ID: 10037184
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: SERVICE BULLETIN EXPLAINING WHEN THE SAFETY BELTS ARE SUPPOSED TO LOCK. *RM UPDATED 12/6/11. *PE
Source components: SEAT BELTS:FRONT:RETRACTOR · SEAT BELTS:FRONT:WEBBING.
Source record 10037184 at NHTSANHTSA communication ID: 10036464
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CADILLAC/CHEVROLET/GMC/HUMMER/PONTIAC/SAAB: OIL CONSUMPTION AND/OR EXHAUST SMOKE-POSSIBLE PCV BAFFLE OR LIFTER CONCERN. UPON INSPECTION, OBVIOUS OIL WILL BE FOUND IN THE INTAKE MANIFOLD AND/OR PCV VACUUM TUBE. *PE UPDATED 3/21/11. *PE UPDATED 5/9/11. *PE UPDATED 5/25/11. *PE UPDATED 06/16/2011. *KB UPDATED A SECOND TIME ON 06/16/2011. *KB UPDATED 6/27/11. *PE
Source components: ENGINE AND ENGINE COOLING:ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
Source record 10036464 at NHTSA