The manufacturer’s record · Page 26 of 26
Original record summaries, dates and identifiers for this model-year. Records 2,501–2,533 of 2,533, ordered newest first. Dated records on this page: Dec 23, 2013–Feb 21, 2014.
Back to 2015 GMC YUKON problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10138638
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains how to balance a chrome wheel without damaging the chrome face of the rim.
Source components: WHEELS.
Source record 10138638 at NHTSANHTSA communication ID: 10138637
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · TIRES · WHEELS:RIM.
Source record 10138637 at NHTSANHTSA communication ID: 10111945
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the door striker cover will be shipped with the vehicle from the assembly plant. Technician is to make sure the rounded side of the cover is positioned towards the outboard side of the vehicle.
Source components: EQUIPMENT.
Source record 10111945 at NHTSANHTSA communication ID: 10111941
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with diagnostic tips about vehicles that have one or more passive entry buttons, located on the outside door handles, are not working or are intermittently working. Technician should ensure the key FOB works within approximately 1 meter (3? 3?) of the door handle where the passive entry button is being operated. Also ensure the customer may not have had their finger or thumb completely on the door handle button. Be advised in cold weather (below 32° Fahrenheit or 0° Celsius), ice may form between the door handle and the button during car washes or thaw / freeze cycles. If a door handle switch is suspected to be defective, it can be component tested.
Source components: ELECTRICAL SYSTEM.
Source record 10111941 at NHTSANHTSA communication ID: 10138631
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on.
Source components: TIRES · WHEELS:RIM.
Source record 10138631 at NHTSANHTSA communication ID: 10138630
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains the use of Nitrogen in GM tires.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · TIRES.
Source record 10138630 at NHTSANHTSA communication ID: 10138629
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information regarding the normal tire wear condition of slight or mild tire feathering and recommended practices.
Source components: TIRES.
Source record 10138629 at NHTSANHTSA communication ID: 10138623
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on part restriction and ordering of Onstar vehicle communication modules.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10138623 at NHTSANHTSA communication ID: 10111933
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the blower motor may be noisy or vibrate when running. This concern will only occur when the temperatures is below 32 degrees Fahrenheit and if the blower motor is removed while still cold, ice may be found on the blower motor cage. This concern could be caused by water leaking or snow ingestion into the Heater-Vent-Air Conditioning case. Technician is to perform normal water testing diagnostics while the Heater-Vent-Air Conditioning is running, looking for water leaking past the plenum cover. If water is leaking past the cover remove the cover and install a 12x12 snow resistant screen to the fresh air intake. Reseal and install the plenum cover cap using Kent air dry sealer or equivalent.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10111933 at NHTSANHTSA communication ID: 10111927
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · FUEL SYSTEM, GASOLINE · SERVICE BRAKES, HYDRAULIC.
Source record 10111927 at NHTSANHTSA communication ID: 10111920
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about systems operate during a remote vehicle start event. Dual Zone Auto Regular Production Option Code (CJ2) Heater-Vent-Air Conditioning settings the Heater-Vent-Air Conditioning settings will remain set to the previous Heater-Vent-Air Conditioning settings when the ignition was turned off. Single Zone Manual Regular Production Option Code (C67) HVAC settings the Heater-Vent-Air Conditioning settings will remain set to the previous Heater-Vent-Air Conditioning settings when the ignition was turned off. The Rear window defogger during a remote start event, the rear window defogger will turn on if the outside temperature is 44 degrees Fahrenheit (7 degrees Celsius) or below. The heated seats will not turn on if a Remote Vehicle Start event is performed within 2 hours of shutting the engine off. The cooled seats will turn to the high setting when the ambient temperature is above 80 degrees Fahrenheit (27 degrees Celsius). Heated steering wheel will not turn on during Remote Vehicle Start event.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10111920 at NHTSANHTSA communication ID: 10111919
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have hard or unable to rotate ignition key concern. When the concern is present the steering wheel will need to be rotated in either direction to alleviate the pressure between the steering column lock pin and lock plate. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:IGNITION · STEERING.
Source record 10111919 at NHTSANHTSA communication ID: 10138606
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletion provides the dealer technician information and guidelines for claiming a windshield.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · VISIBILITY:WINDSHIELD.
Source record 10138606 at NHTSANHTSA communication ID: 10111897
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
Source components: ENGINE · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10111897 at NHTSANHTSA communication ID: 10111893
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an engine extended or long crank time during ambient air temps of ?18° Celsius (0° Fahrenheit) or colder when using E85 fuel. Technician will need to use Global Diagnostic System 2 to determine the actual ethanol content of the fuel. Adding regular fuel to the tank may help resolve the concern.
Source components: ENGINE · FUEL SYSTEM, GASOLINE.
Source record 10111893 at NHTSANHTSA communication ID: 10253622
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Doors Intermittently will not Open from Inside.
Source components: LATCHES/LOCKS/LINKAGES:DOORS:LOCK.
Source record 10253622 at NHTSANHTSA communication ID: 10250084
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels
Source components: WHEELS.
Source record 10250084 at NHTSANHTSA communication ID: 10246571
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels
Source components: WHEELS.
Source record 10246571 at NHTSANHTSA communication ID: 10245771
NHTSA source summary · Original PDF not reviewed by Recallfolio
Proper Wheel Installation and Wheel Torque Techniques
Source components: TIRES · UNKNOWN OR OTHER · WHEELS · WHEELS:LUGS/NUTS/BOLTS/STUDS.
Source record 10245771 at NHTSANHTSA communication ID: 10245768
NHTSA source summary · Original PDF not reviewed by Recallfolio
Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip
Source components: SUSPENSION · SUSPENSION: ADJUSTMENT:MANUAL · TIRES:BEAD · WHEELS.
Source record 10245768 at NHTSANHTSA communication ID: 10190932
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10190932 at NHTSANHTSA communication ID: 10190931
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10190931 at NHTSANHTSA communication ID: 10073749
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ENGINE.
Source record 10073749 at NHTSANHTSA communication ID: 10025705
NHTSA source summary · Original PDF not reviewed by Recallfolio
TIRE SLOWLY GOES FLAT, TIRE AIR LOSS, LOW TIRE PRESSURE WARNING LIGHT ILLUMINATED, ALUMINUM WHEEL BEAD SEAT CORROSION (CLEAN AND RESURFACE WHEEL BEAD SEAT) FOR CERTAIN 2000-2009 GM PASSENGER CARS AND LIGHT DUTY TRUCKS (INCLUDING SATURN). *PE UPDATED 04/15/2014 *JS
Source components: TIRES:BEAD · WHEELS.
Source record 10025705 at NHTSANHTSA communication ID: 10137784
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
Source components: EQUIPMENT.
Source record 10137784 at NHTSANHTSA communication ID: 10112028
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that there is a new DOT 3 brake fluid for the 2014 Silverado and Sierra 1500. Technician can order the new DOT 3 brake fluid from their parts department.
Source components: SERVICE BRAKES.
Source record 10112028 at NHTSANHTSA communication ID: 10137781
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was created to inform that any accessories that are install from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be cover for a full year (12months).
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10137781 at NHTSANHTSA communication ID: 10112022
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10112022 at NHTSANHTSA communication ID: 10112006
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that a driveline noise or vibration at various speeds and operating conditions. Technician should be advised that the vehicle should always be restored to a factory configuration when diagnosing noise and vibration concerns.
Source components: PARKING BRAKE:DRIVELINE.
Source record 10112006 at NHTSANHTSA communication ID: 10112005
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code C0569 that will not clear. Technician should be advised if there are any issues with the rotational position sensor, incremental position sensor, encoder motor, motor A or B circuits, rotational position sensor or incremental position sensor circuits when the transfer case control module attempts to determine location the location cannot be determined correctly.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
Source record 10112005 at NHTSANHTSA communication ID: 10190934
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
Source record 10190934 at NHTSANHTSA communication ID: 10190933
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
Source record 10190933 at NHTSANHTSA communication ID: 10112328
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10112328 at NHTSA