The manufacturer’s record · Page 11 of 12
Original record summaries, dates and identifiers for this model-year. Records 1,001–1,100 of 1,151, ordered newest first. Dated records on this page: Sep 1, 2012–Jan 1, 2013.
Back to 2008 GMC YUKON XL problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10247747
NHTSA source summary · Original PDF not reviewed by Recallfolio
Speedometer Needle Accuracy Information
Source components: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER.
Source record 10247747 at NHTSANHTSA communication ID: 10247092
NHTSA source summary · Original PDF not reviewed by Recallfolio
Speedometer Needle Accuracy Information
Source components: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER.
Source record 10247092 at NHTSANHTSA communication ID: 10112697
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
Source components: EQUIPMENT:MECHANICAL · POWER TRAIN.
Source record 10112697 at NHTSANHTSA communication ID: 10138538
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils.
Source components: ENGINE AND ENGINE COOLING.
Source record 10138538 at NHTSANHTSA communication ID: 10113849
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils.
Source components: ENGINE AND ENGINE COOLING.
Source record 10113849 at NHTSANHTSA communication ID: 10138554
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletins provides information regarding the release of a new designed HVAC blower motor assembley. The bulletin provides information on how to correctly install the parts to function as intended.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10138554 at NHTSANHTSA communication ID: 10113847
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletins provides information regarding the release of a new designed HVAC blower motor assembley. The bulletin provides information on how to correctly install the parts to function as intended.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10113847 at NHTSANHTSA communication ID: 10112688
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that 2ML70 Transmission Assembly will be placed on a parts restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10112688 at NHTSANHTSA communication ID: 10138541
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10138541 at NHTSANHTSA communication ID: 10113843
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10113843 at NHTSANHTSA communication ID: 10138565
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information on replacing the transmission fluid level indicator if a customers comments regarding one being broken.
Source components: POWER TRAIN.
Source record 10138565 at NHTSANHTSA communication ID: 10113842
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information on replacing the transmission fluid level indicator if a customers comments regarding one being broken.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10113842 at NHTSANHTSA communication ID: 10112668
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the puddle light operation. Technician should be advised that the puddle lamps to operate, "Approach Lighting" must be turned on using the Drivers Information Center buttons.
Source components: EXTERIOR LIGHTING.
Source record 10112668 at NHTSANHTSA communication ID: 10112655
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
Source components: TIRES · WHEELS.
Source record 10112655 at NHTSANHTSA communication ID: 10112641
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
Source components: ENGINE AND ENGINE COOLING.
Source record 10112641 at NHTSANHTSA communication ID: 10138544
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides the proper information used to determine the road force variences within new tires being installed and the proper forms used to send the tires back if the road force is not within spec.
Source components: TIRES.
Source record 10138544 at NHTSANHTSA communication ID: 10113838
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides the proper information used to determine the road force variences within new tires being installed and the proper forms used to send the tires back if the road force is not within spec.
Source components: TIRES.
Source record 10113838 at NHTSANHTSA communication ID: 10113837
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10113837 at NHTSANHTSA communication ID: 10138556
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation settings for concernc regarding noice drop outs during calls and muffled sound.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10138556 at NHTSANHTSA communication ID: 10113831
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation settings for concernc regarding noice drop outs during calls and muffled sound.
Source components: EQUIPMENT:ELECTRICAL · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10113831 at NHTSANHTSA communication ID: 10253585
NHTSA source summary · Original PDF not reviewed by Recallfolio
Liftgate Paint Damage Evident at Lower Outer Edge of Applique.
Source components: EQUIPMENT · STRUCTURE:BODY:HATCHBACK/LIFTGATE.
Source record 10253585 at NHTSANHTSA communication ID: 10245772
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diagnostic Tips for Difficult to Resolve Tire/Wheel Vibration Concerns
Source components: SUSPENSION · TIRES · UNKNOWN OR OTHER · WHEELS · WHEELS:LUGS/NUTS/BOLTS/STUDS.
Source record 10245772 at NHTSANHTSA communication ID: 10245770
NHTSA source summary · Original PDF not reviewed by Recallfolio
Proper Wheel Installation and Wheel Torque Techniques
Source components: TIRES · UNKNOWN OR OTHER · WHEELS · WHEELS:LUGS/NUTS/BOLTS/STUDS.
Source record 10245770 at NHTSANHTSA communication ID: 10062548
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: STRUCTURE · STRUCTURE:BODY.
Source record 10062548 at NHTSANHTSA communication ID: 10043510
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC/CHEVROLET/GMC: ORIGINAL STYLE BLOWER MOTOR ASSEMBLY IS NO LONGER AVAILABLE. A REVISED HVAC BLOWER MOTOR ASSEMBLY FOR FULL SIZE TRUCKS IS REQUIRED, WITH MODIFICATIONS, TO FUNCTION PROPERLY. *PE UPDATED 2/25/13. *PE
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10043510 at NHTSANHTSA communication ID: 10138220
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10138220 at NHTSANHTSA communication ID: 10137478
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.
Source components: EQUIPMENT.
Source record 10137478 at NHTSANHTSA communication ID: 10126163
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10126163 at NHTSANHTSA communication ID: 10138218
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats not
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM) · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10138218 at NHTSANHTSA communication ID: 10137476
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats not
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10137476 at NHTSANHTSA communication ID: 10112614
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers may inquire about the availability of the passenger compartment air filter. Dealer should advise the customer starting in 2003 the passenger compartment air filter is no longer available as a factory option.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10112614 at NHTSANHTSA communication ID: 10112613
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
Source components: TIRES:SIDEWALL.
Source record 10112613 at NHTSANHTSA communication ID: 10138217
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10138217 at NHTSANHTSA communication ID: 10137475
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
Source components: EQUIPMENT.
Source record 10137475 at NHTSANHTSA communication ID: 10126171
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
Source components: EQUIPMENT.
Source record 10126171 at NHTSANHTSA communication ID: 10112608
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
Source components: EQUIPMENT:ELECTRICAL · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10112608 at NHTSANHTSA communication ID: 10112607
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
Source components: EQUIPMENT:ELECTRICAL · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10112607 at NHTSANHTSA communication ID: 10112606
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.
Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL.
Source record 10112606 at NHTSANHTSA communication ID: 10112603
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a rattle, buzz, tick, or vibration type noise that appears to be coming from the center of the dash. Technician will adjust the transmission dipstick tube away from the front of cowl to provide additional clearance.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10112603 at NHTSANHTSA communication ID: 10138213
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
Source components: EQUIPMENT · WHEELS.
Source record 10138213 at NHTSANHTSA communication ID: 10137471
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
Source components: WHEELS.
Source record 10137471 at NHTSANHTSA communication ID: 10126191
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
Source record 10126191 at NHTSANHTSA communication ID: 10126164
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a procedure for replacement of the liftgate applique for concerns regarding the applique being deformed or dimpled or paint damage at the lower edge of the applique
Source components: STRUCTURE:BODY:HATCHBACK/LIFTGATE.
Source record 10126164 at NHTSANHTSA communication ID: 10112600
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
Source components: POWER TRAIN:AXLE ASSEMBLY.
Source record 10112600 at NHTSANHTSA communication ID: 10112597
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a buzz or rattle type noise during light acceleration around 1200-2000 Revolutions per minute. Technician will need to reposition the fuel line and bracket down away from the floor pan.
Source components: FUEL SYSTEM, GASOLINE · FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS.
Source record 10112597 at NHTSANHTSA communication ID: 10126192
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10126192 at NHTSANHTSA communication ID: 10112581
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a no crank condition after the vehicle has had very low accessory battery voltage or a dead battery condition. Technician may find Diagnostic Trouble Code P0C76 set. Technician should be advised that anytime a battery charger or booster pack is connected to the 12 volt battery, the ignition key should always be in the off position. If a battery charger or booster pack is connected to the 12 volt battery with the ignition key on tech will need to reset the Hybrid Powertrain Control Module Diagnostic Trouble Codes.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY · ELECTRICAL SYSTEM:IGNITION.
Source record 10112581 at NHTSANHTSA communication ID: 10112580
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Electronic Brake Control Module and Brake Pressure Modulator Valve for the 2-Mode Hybrid Utilities and Trucks will be placed on a parts restriction through the General Motors Technical Assistance Center. Dealer will need to contact for further assistance.
Source components: SERVICE BRAKES.
Source record 10112580 at NHTSANHTSA communication ID: 10112578
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a lack of brake assist after disconnecting the battery or after the 12 volts battery has run low on voltage. The Antilock Braking System Malfunction Indicator Lamp may also be on. Technician may find Diagnostic Trouble Code C121D sym 00 or C056D sym 00 set in the Electronic Brake Control Module. Technician should be advised to wait for a period of at least 1 minute with the ignition in the "OFF" position prior to disconnecting the negative battery cable. Technician will need to follow these steps to repair the concern. 1. Install the negative battery cable to the battery. 2. Rotate the lever lock clockwise until an audible click is heard in order to connect the negative battery cable to the battery. 3. Position the negative battery cable insulating cover over the negative terminal. 4. Start the vehicle without stepping on the brake pedal. 5. Shut the vehicle "Off" for one minute. 6. Restart vehicle and check brakes for proper operation. 7. Clear codes in the Engine Control Module and the Electronic Brake Control Module.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES, ELECTRIC.
Source record 10112578 at NHTSANHTSA communication ID: 10112577
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about Electronic Brake Control Module relearn procedure is required anytime the Electronic Brake Control Module is replaced or has been Service Programming System reprogrammed.
Source components: EQUIPMENT:ELECTRICAL · SERVICE BRAKES, ELECTRIC.
Source record 10112577 at NHTSANHTSA communication ID: 10112573
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the power lift gate Regular Production Option Code (E61 or TB5) is inoperative. Technician will find Diagnostic Trouble Code B153A set in the power lift gate control module. Technician will need to perform these steps. 1. Disconnect the connector at the Lift gate Latch Assembly. 2. Install a 3 ampere fused jumper wire between each signal circuit and the ground circuit. 3. If either test fails, check the wiring for the signal circuits, low reference circuit, or try a power lift gate control module from a known good vehicle. 4. If both tests pass, monitor the internal switch inputs in the lift gate latch assembly for proper operation. 5. If one of the internal lift gate latch assembly switch inputs are not reading correctly in one of the positions above and the vehicles passes test both test, replace the Lift Gate Latch Assembly.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY:HATCHBACK/LIFTGATE.
Source record 10112573 at NHTSANHTSA communication ID: 10137458
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for requesting a new key code for customers with lost or stolen keys
Source components: EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
Source record 10137458 at NHTSANHTSA communication ID: 10126197
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for requesting a new key code for customers with lost or stolen keys
Source components: EQUIPMENT.
Source record 10126197 at NHTSANHTSA communication ID: 10126196
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
Source components: EQUIPMENT.
Source record 10126196 at NHTSANHTSA communication ID: 10138197
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year.
Source components: ENGINE · EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION · SERVICE BRAKES.
Source record 10138197 at NHTSANHTSA communication ID: 10137454
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year.
Source components: EQUIPMENT.
Source record 10137454 at NHTSANHTSA communication ID: 10126200
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10126200 at NHTSANHTSA communication ID: 10126198
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.
Source components: EQUIPMENT.
Source record 10126198 at NHTSANHTSA communication ID: 10112560
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: SERVICE BRAKES.
Source record 10112560 at NHTSANHTSA communication ID: 10126203
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10126203 at NHTSANHTSA communication ID: 10126202
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure for replacing the throttle position sensor cover for concerns regarding a indicator lamp illuminated reduced power message displayed and DTC P2135 set.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10126202 at NHTSANHTSA communication ID: 10112558
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with additional vehicle speed sensor diagnostic information. Technician may encounter multiple issues when diagnosing a Vehicle Speed Sensor. Technician will find it difficult to follow the speed signal path between the components. To test connect the Fluke meter leads between circuits 821 and 822 and set the meter to Alternating current voltage and then press the hertz button. When the Engine Control Module showing correct miles per hour in the data list however it is setting a Diagnostic Trouble Code for the Vehicle Speed Sensor. To test connect the Fluke meter red lead to circuit 6399 and the black lead to ground, then set the meter to Direct current voltage and press the hertz button. The Instrument Panel Cluster speedo will work correctly when the Engine Control Module or Antilock Braking System Diagnostic Trouble Codes are for the Vehicle Speed Sensor. To test connect the Fluke meter red lead to circuit 1827 and the black lead to ground, then set the meter to Direct current voltage and press the hertz button. When the Antilock Braking System Malfunction Indicator Lamp on with Electronic Brake Control Module Diagnostic Trouble Code C0055 and no other customer complaints, to test connect the Fluke meter red lead to circuit 817 and the black lead to ground, then set the meter to Direct current voltage and press the hertz button.
Source components: ELECTRICAL SYSTEM.
Source record 10112558 at NHTSANHTSA communication ID: 10138189
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on how to properly mount and balance wheels and tires on heavy duty truck models only
Source components: TIRES · WHEELS.
Source record 10138189 at NHTSANHTSA communication ID: 10137446
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on how to properly mount and balance wheels and tires on heavy duty truck models only
Source components: TIRES · WHEELS.
Source record 10137446 at NHTSANHTSA communication ID: 10126167
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure to replace the first junction block terminal and other terminals to correct a condition of poor HVAC performance.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10126167 at NHTSANHTSA communication ID: 10112551
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an Antilock Braking System lamp followed by a Service Stability message in the Drivers Information Center. Technician my find Diagnostic Trouble Code C0710 set in the Electronic Brake Control Module. Technician may or may not find Diagnostic Trouble Code C0455. Technician will need to ensure the steering wheel is properly installed to the steering shaft.
Source components: SERVICE BRAKES, AIR:ANTILOCK · SERVICE BRAKES, ELECTRIC · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP.
Source record 10112551 at NHTSANHTSA communication ID: 10112544
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a power steering pump whine noise. Technician will need to flush and refill the power steering system with Lucas Power Steering Fluid with Conditioners. Technician will replace the power steering pump with the latest design if the fluid is not available.
Source components: SERVICE BRAKES, HYDRAULIC:POWER ASSIST · STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID.
Source record 10112544 at NHTSANHTSA communication ID: 10112541
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a buzz or rattle type noise during light acceleration around 1200-2000 Revolutions per minute. Technician will need to reposition the fuel line and bracket down away from the floor pan.
Source components: ENGINE AND ENGINE COOLING.
Source record 10112541 at NHTSANHTSA communication ID: 10112529
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10112529 at NHTSANHTSA communication ID: 10112528
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
Source components: ELECTRICAL SYSTEM.
Source record 10112528 at NHTSANHTSA communication ID: 10043892
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: DIAGNOSE AND REPAIR HVAC BLOWER FUNCTION. MAY NOT BE ANY AIR FLOW FROM THE HVAC VENTS. ONE POSSIBLE OF THIS CONDITION MAY BE THE CONTACTS IN THE HVAC JUNCTION BLOCK(S) LOCATED AT THE RIGHT SIDE OF THE INSTRUMENTAL PANEL. *JS UPDATED 1/24/13. *PE
Source components: VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR.
Source record 10043892 at NHTSANHTSA communication ID: 10112526
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a "Service Stability Message" appears on the Drivers Information Center. Technician will find Diagnostic Trouble Code C0561 set in the Electronic Brake Control Module. Technician will need to address any other Diagnostic Trouble Codes that are set in the vehicle first before working on Diagnostic Trouble Code C0561.
Source components: EQUIPMENT:ELECTRICAL · SERVICE BRAKES, ELECTRIC.
Source record 10112526 at NHTSANHTSA communication ID: 10112519
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have grease leaking from front hub bearings. Technician should not replace the bearing for grease purge. Technician should be advised to not clean the purged grease from the area immediately on or adjacent to the seals because this grease provides additional protection. Technician should only replace the bearing if the seals show visible damage, bearing endplay is greater than 0.005" or 0.13mm, bearing exhibits rough rotation, or bearing exhibits abnormal noise.
Source components: SUSPENSION:FRONT:HUB · WHEELS:HUB.
Source record 10112519 at NHTSANHTSA communication ID: 10112515
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that has a squawk or grunt type noise when shifting from 2nd to 3rd gear. Technician should replace the 3-4 clutch Friction and Steel Clutch Plates along with the Apply Plate and Selective Backing Plate.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10112515 at NHTSANHTSA communication ID: 10112512
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are unable to set a personalized easy exit seat and/or power tilt column position and they will only move a predetermined amount. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · SEATS.
Source record 10112512 at NHTSANHTSA communication ID: 10112508
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks and Utilities may ask if they can lower their tire pressures. Tire pressures being set to the "Tire and Loading Label" will ensure the safe handling and ride characteristics of the truck and should not be lowered.
Source components: TIRES.
Source record 10112508 at NHTSANHTSA communication ID: 10112494
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10112494 at NHTSANHTSA communication ID: 10118638
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2 or GDS 2
Source components: ENGINE AND ENGINE COOLING.
Source record 10118638 at NHTSANHTSA communication ID: 10118637
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:OTHER:LABELS.
Source record 10118637 at NHTSANHTSA communication ID: 10118635
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a procedure for relearning the power folding mirriors and road testin to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions.
Source components: VISIBILITY:REARVIEW MIRRORS/DEVICES.
Source record 10118635 at NHTSANHTSA communication ID: 10118634
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10118634 at NHTSANHTSA communication ID: 10112472
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that if the ignition key is turned to the start position, and then released when the engine begins cranking, the engine will continue cranking for a few seconds or until the vehicle starts. Some customers may state that this feature is inoperative. Technician should be advised that if the Low Fuel warning lamp is on and/or the FUEL LEVEL LOW message is displayed in the Driver Information Center, the Computer?Controlled Cranking System will be disabled.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:IGNITION.
Source record 10112472 at NHTSANHTSA communication ID: 10084683
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS.
Source components: EQUIPMENT · STRUCTURE.
Source record 10084683 at NHTSANHTSA communication ID: 10112470
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an instrument panel backlighting flashes, flickers or inoperative, unwanted horn activation, radio controls inoperative or unwanted activation, OnStar unwanted activation, and cruise control inoperative. Technician should inspect for a short to ground on the steering wheel near the Supplemental Inflatable Restraint coil connector X2 and make necessary repairs to any shorted circuits and then position the wiring.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC. · VEHICLE SPEED CONTROL:CRUISE CONTROL.
Source record 10112470 at NHTSANHTSA communication ID: 10112468
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces Ultraviolet rays down to 4% or less. Front side door glass reduces Ultraviolet rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.
Source components: VISIBILITY:GLASS, SIDE/REAR · VISIBILITY:WINDSHIELD.
Source record 10112468 at NHTSANHTSA communication ID: 10112465
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
Source components: EQUIPMENT:ELECTRICAL · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10112465 at NHTSANHTSA communication ID: 10118626
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10118626 at NHTSANHTSA communication ID: 10118623
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administrational bulletin provides information on courtesy transportation and roadside assistance programs offered through GM.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10118623 at NHTSANHTSA communication ID: 10118619
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on newly release bulletins used to fi the vehicles in the field the first time.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10118619 at NHTSANHTSA communication ID: 10112452
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the cruise control being inoperative. Technician may find Diagnostic Trouble Code B3894 set in the Trailer Brake Control Module. Technician should follow published Service Information diagnostics first. Technician should check the "Master Cylinder Pressure" sensor parameter listed in the Trailer Brake Control Module data list. If it is displaying pressure with no brake pedal input, suspect a concern with the Master Cylinder Pressure Sensor, wiring/terminals, or Electronic Brake Control Module.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL.
Source record 10112452 at NHTSANHTSA communication ID: 10247741
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various Concerns Related To The IP Backlighting Cruise Control Steering Wheel Controls Horn.
Source components: STEERING · VEHICLE SPEED CONTROL:CRUISE CONTROL.
Source record 10247741 at NHTSANHTSA communication ID: 10247656
NHTSA source summary · Original PDF not reviewed by Recallfolio
Cruise Control Inoperative.
Source components: ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL · UNKNOWN OR OTHER · VEHICLE SPEED CONTROL:CRUISE CONTROL.
Source record 10247656 at NHTSANHTSA communication ID: 10247087
NHTSA source summary · Original PDF not reviewed by Recallfolio
Computer-Controlled Cranking System (Bump Start) Inoperative.
Source components: ENGINE AND ENGINE COOLING.
Source record 10247087 at NHTSANHTSA communication ID: 10247086
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various Concerns Related To The IP Backlighting Cruise Control Steering Wheel Controls Horn.
Source components: STEERING · VEHICLE SPEED CONTROL:CRUISE CONTROL.
Source record 10247086 at NHTSANHTSA communication ID: 10246951
NHTSA source summary · Original PDF not reviewed by Recallfolio
Programming And Activation Of Replacement OnStar Modules.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10246951 at NHTSANHTSA communication ID: 10245295
NHTSA source summary · Original PDF not reviewed by Recallfolio
Cruise Control Inoperative.
Source components: VEHICLE SPEED CONTROL · VEHICLE SPEED CONTROL:CRUISE CONTROL.
Source record 10245295 at NHTSANHTSA communication ID: 10118610
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the AFM oil deflector, rocker arm cover and clean the carbon deposits for conditons related to Engine Oil Consumption on Aluminum Block/Iron Block Engines with Active Fuel Management
Source components: ENGINE AND ENGINE COOLING.
Source record 10118610 at NHTSANHTSA communication ID: 10062524
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ENGINE.
Source record 10062524 at NHTSANHTSA communication ID: 10047839
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC/CHEVROLET/GMC: WILL HAVE INOPERATIVE CRUISE CONTROL; INOPERATIVE OR UNWANTED ACTIVATION OF RADIO CONTROLS; BACKLIGHTING FLASHES, FLICKERS OR INOPERATIVE DUE TO POSSIBLE SHORT TO GROUND ON STEERING WHEEL COIL CONNECTOR X2. MODELS 2007-2013 ESCALADES MODELS, AVALANCHE, SILVERADO, SUBURBAN, TAHOE, SIERRA, YUKON MODELS. *PE
Source components: ELECTRICAL SYSTEM · STEERING: STEERING WHEEL/HANDLE BAR.
Source record 10047839 at NHTSANHTSA communication ID: 10247740
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Button Backlighting Inoperative.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10247740 at NHTSA