Original record summaries, dates and identifiers for this model-year. Records 901–1,000 of 1,151, ordered newest first. Dated records on this page: Jan 3, 2013–Jun 3, 2013.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jun 3, 2013Service Bulletin/Repair Instructions
13-02-32-001A
NHTSA communication ID: 10134624
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision for 13-02-32-001 to update the models information.
Source components: STEERING:HYDRAULIC POWER ASSIST SYSTEM · STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Suspension System message on the Driver Information Center and the rear suspension ride height is incorrect. Technician will find Diagnostic Trouble Code C0696 or C0711 set in Electronic Suspension Control. Technician will need to inspect air compressor assembly for wire damage and repair any damage do not replace the complete air compressor assembly. Some vehicles may have a Service Suspension System message on the Driver Information Center and may also comment that the rear suspension ride height may be low under a heavy payload. Technician will follow published Service Information diagnostics and if determine if the sensor needs to be replaced technician will need to replace a complete air filter, dryer, and sensor assembly. Some vehicles may have a loose hose hanging down in the left rear of the vehicle. Technician will replace the auto leveling compressor air inlet filter and hose assembly. Also some vehicles may have automatic level control compressor is no longer performing a self-test at start up. Be advised the automatic level system normally will not or very infrequently cycle the compressor at key up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that after installing the GM Accessory Heated Seat Kit, one or more of the following issues may be present the heated seat back and/or bottom turns off after approximately 30 seconds and after turning on the heated seat switch, the indicators remain on, but the seat is not heating. Technician may find Diagnostic Trouble Codes B1935 Sym 0E, B2180 Sym 0E, B2425 Sym 0D, and/or B2430 Sym 0D. Technician will need to inspect the accessory heated seat wiring harness and make sure the heater element connectors are installed correctly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 09-03-16-002A to add model years, add the current Global Labor Time Code and update the tool reference information.
Source components: EQUIPMENT · TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation under Courtesy Transportation Warranty Transaction Submission.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the Multiple Diagnostic Interface or Techline computer terminal locks up during Service Programming System Sequential Programming or failed Service Programming System Sequential Programming event or no communication with any one Hybrid module. Technician will need to contact Techline customer support center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that after refueling the fuel gauge will show empty. Technician will find Diagnostic Trouble Code P2636. Dealer should question the owner if the key or engine is on while refueling. Dealer should the owner to turn the engine and key off, before refueling the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have at times the XM Traffic or Weather for the local area takes several minutes to update and may read "NO DATA" or "UPDATING" during that time. Technician should be advised that Traffic and Weather data from local reporting stations and then send the updated info process may take up to 24 minutes. Technician should test for full operation of the XM band if the system has not started receiving the Traffic and weather update within 30 minutes. Also ensure the customer has not shut XM NavTraffic off in the user settings of the navigation radio. Technician will need to contact XM customer assistance to review the account status and verify that the XM Traffic option has been enabled and is available in the area.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that for no reason the alarm will go active. Technician will need to use a scan tool to verify that the alarm was activated by the inclination sensor. If the trigger is the inclination sensor, inspect the sensor's mounting location. Technician will need to relocate the sensor if it is attached to the driver's side lower Heater-Vent-Air Conditioning duct. Technician will need to reinstall the sensor to the top of the Body Control Module bracket.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision of 03-06-03-003B to add the 2010-2014 model years, update the Attention statement, change the terms Claim Type B to Claim Type ZPTI, GM Dealer to GM Service Agent, Repair Order to Job Card, Warranty Claim to Warranty Transaction, and to update the Procedure Information for submitting Vehicle Repairs from WINS to Global Warranty Management (GWM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision of 12-04-21-001A to add the 2013 model year, clarify the information from the previous bulletin and to add data throughout. The document should be reviewed and treated as new information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:COOLING SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a radio display that will show "LOCKED" or "THEFT LOCK". Technician will need to replace the radio If the radio stills displays "LOCKED" or "THEFT LOCK" after SPS programming.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have navigation or radio screen is blank or flashes on and off, no sound from speakers, and rear DVD screen inoperative. Technician will find Diagnostic Trouble Codes B1265, B1288, or B1289. Technician will need to repair circuit 7066.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2® or global diagnostic system 2 (GDS 2)
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that 2-Mode Drive Motor Generator Battery will be placed on a parts restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a procedure to adjust the transmission dipstick tube and/or install the transmission fluid filler tube sleeve to eliminate a tick, buzz or rattle noise from the front of dash, transmission filler tuber cracked or broken.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code B2555 may be found in a Driver and/or Passenger Door Module. Technician should ignore the Diagnostic Trouble Code if set in a driver door module and/or Passenger Door Module on a vehicles not equipped with front door panel courtesy lights.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY:DOOR · VEHICLE SPEED CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a radio display that will show "LOCKED" or "THEFT LOCK". Technician will need to replace the radio If the radio stills displays "LOCKED" or "THEFT LOCK" after SPS programming.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that a driveline noise or vibration at various speeds and operating conditions. Technician should be advised that the vehicle should always be restored to a factory configuration when diagnosing noise and vibration concerns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code C0569 that will not clear. Technician should be advised if there are any issues with the rotational position sensor, incremental position sensor, encoder motor, motor A or B circuits, rotational position sensor or incremental position sensor circuits when the transfer case control module attempts to determine location the location cannot be determined correctly.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET: THE PASSENGER AND/OR DRIVER DOOR MODULE COURTESY LIGHTS CALIBRATIONS ARE THE SAME, WITH OR WITHOUT, DOOR PANEL COURTESY LIGHTS. MODEL 2007-2013 AVALANCHE, SILVERADO, SUBURBAN, TAHOE, SIERRA, YUKONS. 8PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC: HYDRAULIC POWER STEERING LEAK AT HOSE CONNECTION TO STEERING RACK. ALL POTENTIAL LEAKS SHOULD BE COMPLETELY CLEANED AND INDENTIFIED BEFORE ATTEMPTING TO REPAIR OR REPLACE ANY POWER STEERING COMPONENTS. *JS UPDATED 4/22/13. *PE
Source components: STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a cold air leak on the front passenger side while driving. Technician will need to use black RTV silicone and apply over the seam between the upper and lower Heater-Vent-Air Conditioning case halves.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for service agents not required to contact product quality center for CNG, LPG or gasoline engine, transmission and/or transfer case.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to install AFM oil deflector, rocker arm cover-left bank and clean carbon from cylinder due to engine oil consumption on aluminum block/iron block engines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure for adding double sided tape on the right and left windshield side reveal moldings to remove tapping, clicking or ticking type noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a service 4WD message displayed in the Driver Information Center. Technician may find Diagnostic Trouble Code C0379. Technician will need to inspect the front axle actuator connector for signs of moisture intrusion. If there is corrosion on the terminals at either location replace the actuator and harness.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 miles per hour at any given speed when looking straight at the needle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have misfires on cylinders 1, 4, 6 and 7. Technician should inspect the camshaft part numbers. Technician should ensure to use part number for the application by using the numbers stamped on the cam.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to install the updated valve cover for models built with the prior date listed to correct oil consumption of vehicles with higher mileage.