2016 GMC SIERRA 2500 Manufacturer communications & TSBs.Page 13
Original record summaries, dates and identifiers for this model-year. Records 1,201–1,300 of 1,582, ordered newest first. Dated records on this page: Aug 10, 2016–Nov 18, 2016.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Nov 18, 2016Service Bulletin/Repair Instructions
PIT5434A
NHTSA communication ID: 10114840
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician only to provide additional tips when diagnosing a front heated seat concern and is not meant to be a diagnostic flow chart or replace Service Information. Always, perform and refer to Service Information for the latest diagnostic information and procedures. Trucks equipped with heated and cooled seats Regular Production Option Code (KB6), may comment on any of the following front heated seat concerns. Condition 1, a front heated seat (back and/or cushion) is inoperative. Technician should diagnosis each affected seat heater individually. Technician should test all four circuits Power, Ground, Control (from Body Control Module) and Heating Element Supply Power. The Power, Ground, Control (from Body Control Module) can easily be checked by starting the engine and turn on the cooled seat. When the cooled seats are turned on the blower in each seat back and cushion will turn on at that point technician will be able to hear the blower moving. The heating element supply power circuit can be test by disconnecting the affected heating element and connect a voltmeter across the heating element supply power and ground circuit. Then start the engine and turn on the heated seat, the blower will supply system voltage on the element supply power circuit for 1 to 2 seconds. With the heated seat element disconnected, use an ohmmeter to measure the resistance of the heating element. If all of the above steps check ok or the heating element resistance is close to the approximate spec, reconnect all disconnected connectors. Connect a voltmeter across the affected heated seat element connectors supply power and ground circuits back probing the connector. Then check the resistance of the heating element. The resistance should be close to the same resistance as when testing with the connector unplugged. Now check the voltage with the engine running and the heated sets on high. Condition 2, the front heate
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have Trailer connection not recognized or ?Check Trailer wiring? or ?Service Trailer Brake? message. Technician may find Diagnostic Trouble Codes C1112, C1113, C1114, C111B, U1556, and/or U1505. Technician will need to inspect the Trailer Brake Power Module connector for corroded terminals and replace as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel regarding formulation of a lighter variant paint being made available in order to match the paint on trucks exhibiting a lighter color due to mis-application at the plant.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 miles per hour steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will need to run the vehicle in three different operational modes. The three modes are Normal, torque converter clutch open, and torque converter clutch closed. Technician will need to press and hold the tow-haul mode button for five seconds to disable grade braking to prevent downshifts during test. Technician will need to duplicate the concern in Normal mode. If the concern is gone in torque converter clutch open and closed then the torque converter should be replaced. If the concern is not present in normal mode, torque converter clutch open, and torque converter clutch closed the concern is not with the shudder. Technician should use of the PICO scope and Noise, Vibration and Harshness software can be used to confirm torque converter clutch shudder, Engine, Tire or Driveline component related conditions. Flush the cooler lines and cooler using DT-45096 transmission oil cooling system flush and flow test tool when the torque converter is replace.
Source components: POWER TRAIN · SERVICE BRAKES · VEHICLE SPEED CONTROL:LINKAGES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnosis and repair steering that feels loose or has excessive play. This concern could be caused by the Pitman Shaft Over-Center Preload Adjustment becoming misadjusted. Technician will need to replace the steering gear pitman arm shaft with an updated design.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have harsh concerns. Technician are advised to use GDS2 software to confirm which shift is causing the concern. On low mileage vehicles technician are instructed to perform a drive learn procedure. On higher mileage vehicles technicians are instructed to remove the transmission fluid pan and inspect for debris. If debris is found technicians should disassemble and inspect for root cause of the concern and repair the transmission as needed. If no debris is found technicians are advised to replace the valve body.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an exhaust leak, noisy exhaust, or noise mid-vehicle. Technician will need to check for an unseated pipe to pipe mid-joint connection. Technician will need to install new exhaust band.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of a MIL or a engine misfire due to a loose spark plug wire.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Technical Bulletin provides a fix to reprogram the radio for vehicles that may experience any of the following conditions: DTC U0184 Set, Radio Inoperative, Blue Screen, AM Clipping Noise, HD On/Off Status Not Retained in Stations, Time Lag on Transitions, No Audio with Internal Amp, Park Assist Symbol Position Wrong in Rear View Camera
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have harsh shifts concerns. Technicians will use Global Diagnostic System 2 software to confirm which shift is causing the concern. On low mileage vehicles technician are instructed to perform a drive learn procedure. On higher mileage vehicles technicians are instructed to remove the transmission fluid pan and inspect for debris. If debris is found in the pan, technicians should disassemble and inspect for root cause of the concern and repair the transmission as needed. If no debris is found technicians are advised to replace the valve body.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides the technician with information on vehicles with navigation radio Regular Production Option Code IO6 or UY4 that defaults to West Virginia instead of Virginia on a manual entry. General Motors engineering is currently working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that generation 5 engines with Regular Production Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner?s Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before you contacting General Motors Product Quality Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some vehicle may have an ?Exhaust Fluid Quality Poor? on the Driver Information Center or a diesel exhaust fluid warning lamp on or other exhaust fluid quality related concerns. Technician will inspect the diesel exhaust fluid for contamination. Technician should use Service Information for Contaminants in Diesel Exhaust Fluid Diagnosis and use special tool J26568 or EN50422 Diesel Exhaust Fluid Refractometer for fluid testing.
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to clean and repair the complete fuel system due to dirt getting into the fuel system causing the vehicle to have a hard or no start.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair vehicles with a rough idle and/or vibration at idle in Drive. This condition will not be present in Park, or Neutral. This concern may be caused by ground out within the one or both engine mounts. Technician will use CH-51450-A (Pico Oscilloscope) to measure the vibration disturbance. If the vibration concern is E1.5 in the horizontal / lateral direction with Pico sensor mounted in seat track as indicated ? continue with steps to reduce the amplitude of the vibration by adding spacers in key locations to reduce ground out within the engine mounts. The 6.2L engine has a characteristic E1 which can be felt, and may be described as a lopey idle. Do not confuse 6.2L E1 characteristic (not caused by mount ground-out), with E1.5 normal idle characteristics being transmitted into the truck via ground-out thru the engine mounts. If measuring high at the seat track 12 mg or greater; replacement of the engine mounts should help reduce the amplitude of the vibration. If the disturbance measures at the seat track as E1.5 lateral in the range of approximately 2.5 - 8 mg using a tri-axis sensor. Then place tri-axis Pico sensor on the inboard seat track forward-most location to record measurement of the rough idle vibration concern. With the Heater-Vent-Air Conditioning on perform several short heavy launch events from stop to stop to bring the temperatures back up while attempting to re-create the rough idle vibration in Drive with Pico sensor placed on inboard seat track; while the vibration is active ? Record Pico reading. This method seems to provide better results than extended test drives. If the Pico reading for E1.5, with vibration active, at specified seat track location measures close to 2mg or less use Service Information to diagnose rough idle / vibration. If the Pico reading for E1.5, with vibration active, at the inboard forward seat track l
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to replace the propeller shaft if technicians find a broken propeller shaft or U-joint due to different causes.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides the technician with the steps needed to diagnose and repair a vehicle with Wi-Fi or Bluetooth inoperative or poor performance concern. Technician will need to obtain data from Global Diagnostics Services 2 and call General Motors Technical Assistance Center for further assistance. Technician should be advised that concern only applies to OnStar Wi-Fi Regular Production Option Code (VV4) and Bluetooth Regular Production Option Code (UPF).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
NHTSA source summary · Original PDF not reviewed by Recallfolio
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a service engine soon malfunction indicator lamp, antilock braking system malfunction indicator lamp, service suspension system message, misfire, hesitation, no crank, heater-vent-air conditioning inoperative. Technician may find F11UA, F104UA, F35UA, and or F60UA blown. Technician should inspect the engine harness near the vacuum pump pulley to be chafing. Technician will need to reroute the wire harness and repair and damaged wires.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin has been Revised to add the 2017 Colorado, Cruze, Canyon, Chevrolet & GMC Light/Medium Duty Trucks. Please discard Corporate Bulletin Number 03-06-04-071I
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 mph steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will drive the vehicle and monitor the torque converter clutch slip. The torque converter clutch slip speed should be 10 rpm or less also note if the shudder takes place during torque converter clutch apply. If the torque converter clutch slip speed is in the range of 10 RPM or less the condition is possibly related to engine performance. If the shudder is only present in 4 cylinder mode and torque converter clutch slip is 10 rpm or less deem the shudder concern normal characteristic of Active Fuel Management. If the slip speed is beyond 10 rpm or there is shudder during torque converter clutch apply the torque converter will need to be replaced. Also flush the cooler lines and cooler using DT-45096 transmission oil cooling system flush and flow test tool.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Technician will need to Clear All Private Data and repair any phones that were deleted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of a check trailer message displayed but there is no trailer connected.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the voice recognition is inoperative. Technician will need to toggle through all languages then back to the desired language.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the A4 Hybrid/EV battery Pack, A28 Generator Battery Disconnector Relay, K114B Hybrid/EV Powertrain Control Module, and G14 Drive Motor Generator Battery Cooling Blower has been placed on parts restriction by General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Starter Generator has been placed on parts restriction by General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Generator Control Module has been placed on parts restriction by General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL on.
Source components: BACK OVER PREVENTION · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
Source components: ELECTRONIC STABILITY CONTROL (ESC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides multiple fixes for a condition of a waiting for update screen appearing on the display, due to either a reprogramming of the hmi module or due to a fuse that needs to be pulled and restarting of the module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps to diagnose and repair the concern of the display is showing 32° F (0° C) after a battery or reprogramming a module. The outside temperature will begin to update if driven above 20 mph for at least 5 minutes. If the vehicle speed drops below 20 mph, the timer will reset and the display will stop updating. Once the display starts to update it may take several more minutes of driving above 20 mph for the display to fully update. Also if the vehicle is shut off for more than 8 hours the display will update when the ignition is turned on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare after the vehicle has been sitting for a period of time. Technician can update the Transmission Control Module if working on a model year 2007. On all other model years dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides guidelines for Dealers to determine whether or not they need to contact the PQC for an engine, transmission or transfer case assembly replacement and information explaining the PQC process, Global Warranty Management Transaction submission, vehicle repair record retention and proper handling of assembly returns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The information in this bulletin details the proper configurations for the ignition key, fob, key tags and key rings and applying a QR code sticker or barcode sticker to a key fob.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the parts restriction has ended on the 6.6L Duramax engine Regular Production Option Code (LML/LGH) part number 12638502. Dealer can now order parts through the normal Customer Care and Aftersales parts process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the flanges when the repairs are done.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Both Front Low Beam, High Beam, Day Time Running Lamps (DRL) and Turn Signals Inoperative.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin was created to inform Service Agents or Dealers, they may be charged back for parts and labor due to the turbo-chargers are being returned to the Warranty Parts center damaged, improperly assembled or missing parts and advising to properly package the complete turbochargers. (New models and RPOs added)
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the Homelink transmitter to correct the customers concern of the garage door wont open from far distances.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This GM of Canada New Vehicle Tire Warranty Program and GWM Transaction Submission Information Bulletin provides information for the new tires that the vehicle are equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage) and for vehicles within this warranty period, the defective tires will be replaced on a pro rata adjustment basis. It also provides GWM Transaction information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is ending the need of information from the field on vehicles with the condition of a rattle noise from the second row seat.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to reprogram the radio to correct a customer concern of radio Inoperative, blue Screen, AM clipping noise, HD on/off status not retained in stations, time lag on transitions, no audio with internal amp, park assist symbol position wrong in rear view camera.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on GM offering the Android Auto feature upgrade for 2016 and 2017 model year vehicles and how to proceed with reprogramming the vehicles to include this application for use.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles with the condition of a check engine light illuminated and a DTC of P0751, in addition the vehicles have less then 5,000 miles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS INFORMATIONAL BULLETIN PROVIDES THE CORRECT INFORMATION THAT IS NEEDED TO CORRECTLY KNOW WHAT TPM SENSOR IS NEEDED TO BE INSTALLED ON VEHICLES IF THERE IS ACCESSORY WHEELS INSTALLED AND WHO TO CONTACT WHEN THE ACCESSORY WHEELS WILL NOT LEARN THE TPM'S TO THE VEHICLES.
Source components: EQUIPMENT · TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HUMAN MACHINE INTERFACE, RADIO OR TUNER, RADIO CONTROLS, INTEGRATED CENTER STACK, DISPLAY, AND MEDIA DISC PLAYERS ARE PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER. DEALER WILL NEED TO CONTACT GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO ENABLE THE 4G LTE WIFI ON NEWLY DELIVERED VEHICLES FOR SOME VEHICLES THAT WERE NOT SHIPPED WITH THE FEATURE NOT ENABLED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS TECHNICAL BULLETIN PROVIDES THE PROCEDURES TO COMPLETE A TRANSSMISSION ADAPTIVE LEARN ON ALL THE DIFFERENT TYPES OF VEHICLES AND TRANSMISSIONS BASED ON RPO OPTIONS TO CORRECT A CONDITION OF HARSH SHIFTS ON HARD ACCELLERATIONS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS TO DIAGNOSIS AND REPAIR VEHICLES WITH VARIOUS HANDLING, VEHICLE DYNAMICS CONCERNS, NOISES FROM THE SUSPENSION OR UNDERBODY, OR ISSUES RELATED TO DAMAGED SUSPENSION COMPONENTS. BEFORE ANY IN-DEPTH DIAGNOSTICS ARE PERFORMED, BE AWARE THAT VARIOUS ISSUES COULD OCCUR IF THE VEHICLE HAS BEEN MODIFIED AND INFORM THE CUSTOMER THE CONDITIONS NOTED MAY NOT BE COVERED UNDER WARRANTY. TECHNICIAN WILL INSPECT FOR INSTALLED AFTERMARKET SUSPENSION COMPONENTS. ALSO INSPECT FOR IMPROPERLY ADJUSTED TORSION BARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE REAR ENTERTAINMENT MEDIA DISC PLAYER USING A PROVIDED DVD TO CORRECT THE CONDITION OF THE REAR ENTERTAINMENT PLAYER FREEZES ON START UP MENU DUE TO A CALIBRATION CONCERN.