The manufacturer’s record · Page 1 of 2
Original record summaries, dates and identifiers for this model-year. Records 1–100 of 145, ordered newest first. Dated records on this page: Dec 9, 2016–May 7, 2026.
Back to 2015 Ford MUSTANG problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 11033580
NHTSA source summary · Original PDF not reviewed by Recallfolio
Harvest Program 26H02 Certain 2015 Model Year Mustang, Fusion, and Edge Vehicles Driver Airbag Module Replacement
Source components: AIR BAGS.
Source record 11033580 at NHTSANHTSA communication ID: 11031781
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Program 25N15 - Supplement #1 Certain 2015-2019 Model Year Multiple Vehicle Lines Rear View Camera Inspection For One-Time Replacement
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
Source record 11031781 at NHTSANHTSA communication ID: 11029052
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
Source record 11029052 at NHTSANHTSA communication ID: 11027801
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015-2019 Model Year Multiple Vehicle Lines Rear View Camera Inspection For One-Time Replacemen
Source components: VISIBILITY/WIPER.
Source record 11027801 at NHTSANHTSA communication ID: 11026915
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015-2019 Model Year Multiple Vehicle Lines Rear View Camera Inspection For One-Time Replacement
Source components: UNKNOWN OR OTHER · VISIBILITY/WIPER.
Source record 11026915 at NHTSANHTSA communication ID: 11025611
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
Source record 11025611 at NHTSANHTSA communication ID: 11020247
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ford Motor Company is voluntarily conducting a study on some customer-owned vehicles to proactively replace the front seat belt retractors and return them to Ford for further analysis. Inspecting your vehicle will help Ford carry out this research.
Source components: SEAT BELTS.
Source record 11020247 at NHTSANHTSA communication ID: 11009917
NHTSA source summary · Original PDF not reviewed by Recallfolio
This is a proactive investigation program by Ford Motor Company to obtain field parts for evaluation. Ford is voluntarily conducting this program to evaluate the field performance and functionality of the obtained front seat belt retractor assemblies. Parts obtained from the program must be returned to Ford for evaluation.
Source components: SEAT BELTS.
Source record 11009917 at NHTSANHTSA communication ID: 11008948
NHTSA source summary · Original PDF not reviewed by Recallfolio
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
Source components: UNKNOWN OR OTHER.
Source record 11008948 at NHTSANHTSA communication ID: 10254138
NHTSA source summary · Original PDF not reviewed by Recallfolio
All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
Source components: EQUIPMENT.
Source record 10254138 at NHTSANHTSA communication ID: 10251952
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
Source components: ENGINE AND ENGINE COOLING.
Source record 10251952 at NHTSANHTSA communication ID: 10251951
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2024 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a tick tap and/or typewriter ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150°F (65°C) or higher and engine speed is at idle up to approximately 1700 RPM. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise tick rate can be faster or slower and is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted. This information along with an example audio clip has been added to the WSM Section 303-00 Engine System General Information > Diagnosis and Testing > Engine > PPT F > Step F2.
Source components: ENGINE AND ENGINE COOLING.
Source record 10251951 at NHTSANHTSA communication ID: 10251934
NHTSA source summary · Original PDF not reviewed by Recallfolio
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
Source components: POWER TRAIN.
Source record 10251934 at NHTSANHTSA communication ID: 10248371
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 Mustang vehicles built on or before 30-Aug-2020 may exhibit a rattle like noise coming from the front seat. This may be due to the mating surface between the seat frame and floor pans. To correct this condition, follow the Service Procedure to clean the mating surface.
Source components: EQUIPMENT.
Source record 10248371 at NHTSANHTSA communication ID: 10246072
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015 â 2021 Model Year Mustang Convertible Vehicles - Door Opens to Secondary Latch Position
Source components: LATCHES/LOCKS/LINKAGES · STRUCTURE:BODY:DOOR.
Source record 10246072 at NHTSANHTSA communication ID: 10243652
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-Super Duty and 2015-2020 F-150/Mustang vehicles may require replacement of the powertrain control module (PCM) for various reasons. While performing a programmable module installation (PMI) using the Integrated Diagnostic Service (IDS) scan tool, an error message may state: Configuration Failed, Would You Like To Retry? This may be due to improper module replacement steps. Make sure that the original module is installed in the vehicle, delete the vehicle session, then start a new vehicle session. Once the session starts, run the PCM PMI and install the new PCM only when the scan tool instructs. Finish the PMI by following the prompts given by IDS. If the original PCM is not available, it is possible to configure the module by running as-built programming on the PCM. When IDS asks to obtain part numbers or configuration data, select configuration data.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10243652 at NHTSANHTSA communication ID: 10240305
NHTSA source summary · Original PDF not reviewed by Recallfolio
Spl Parts, Inc. communications index accompanying MCP uploads 23mc40464 & 23mc40471
Source components: EQUIPMENT · STEERING · SUSPENSION.
Source record 10240305 at NHTSANHTSA communication ID: 10240266
NHTSA source summary · Original PDF not reviewed by Recallfolio
SPL Parts, Inc. manufacturers and distributes aftermarket lower control arms for dedicated competition vehicles and "track day" cars some of which may be used on both track and highway. SB 23-01 adresses proper installation torque of cap bolt fasteners attaching SPL's aftermarket lower control arms, recurring inspection and confirmation of torque setting and removal and replacement of damaged or under torqued fasteners to reduce risk of premature failure and accident. SB-23-01 was mailed, emailed and posted on SPL website to known resellers, race teams and users of the affected parts and is being submitted here as required by part 579.5. Vehicle Applications include: BMW series 1,2,3,& 4, 2008-2023; Chevrolet Camaro 26-2023, Cadillac ATS, CTS 2016-2019; Ford Mustang 2015-2023; Toyota Supra 2020-2023.
Source components: EQUIPMENT · STEERING · SUSPENSION.
Source record 10240266 at NHTSANHTSA communication ID: 10235153
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
Source components: STRUCTURE.
Source record 10235153 at NHTSANHTSA communication ID: 10230933
NHTSA source summary · Original PDF not reviewed by Recallfolio
During replacement of the electronic power assist system (EPAS) steering gear assembly on 2015-2023 Mustang vehicles, removal and replacement of the inner tie rods and bellows boots is required. To assist engineering with root cause analysis of failed steering gears, include these parts in the same package when returning warranty replacement steering gears. Make sure to avoid damage to the bellows boots or inner tie rods during removal. The steering gear should also be packaged in the original box with all protective insulators in place to properly protect it during shipping.
Source components: STEERING.
Source record 10230933 at NHTSANHTSA communication ID: 10228876
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
Source components: SERVICE BRAKES.
Source record 10228876 at NHTSANHTSA communication ID: 10222788
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10222788 at NHTSANHTSA communication ID: 10222526
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2014 - 2015 Model Year, Fusion and MKZ and 2015 Model Year Mustang Vehicles Brake Stop Lamps Remain On REF: Safety Recall 22S02 Certain 2014 - 2015 Model Year, Fusion and MKZ and 2015 Model Year Mustang Vehicles Brake Stop Lamps Remain On Submitting Owner Letters and Tech Bulletin
Source components: ELECTRICAL SYSTEM.
Source record 10222526 at NHTSANHTSA communication ID: 10214761
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2022 Mustang vehicles may exhibit a water leak onto the front carpet that originates from the either the left or right A-pillar. This may be due to a detached A-pillar body seal. Follow the service procedure to repair the vehicle.
Source components: STRUCTURE:BODY:ROOF AND PILLARS · UNKNOWN OR OTHER.
Source record 10214761 at NHTSANHTSA communication ID: 10212957
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
Source components: ELECTRICAL SYSTEM.
Source record 10212957 at NHTSANHTSA communication ID: 10211957
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2014 - 2015 Model Year, Fusion and MKZ and 2015 Model Year Mustang Vehicles Brake Stop Lamps Remain On - Under Safety Recall 22S02, in some of the affected vehicles, exposure to a high temperature, high humidity, and high salinity environment is causing the brake pedal âÂÂstop bumperâ to disintegrate and fall off on some of the affected vehicles resulting in the brake stop lamps remaining on continuously, even when the brake pedal is not applied. If the brake pedal bumper is missing on automatic transmission vehicles, the engine can be started, and the transmission can shift out of park without depressing the brake pedal. For 22R01, owners will be instructed to request a repair under this regional program if their vehicle exhibits brake pedal concerns or if they are concerned about the brake pedals in their vehicles.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING:BRAKE LIGHTS.
Source record 10211957 at NHTSANHTSA communication ID: 10210472
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 Mustang Shelby GT350/GT350R vehicles may exhibit a hesitation or surge in the vehicle with no diagnostic trouble codes (DTCs) present. This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has come loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. To resolve the condition, follow the Service Procedure steps to replace the output shaft flange nut.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10210472 at NHTSANHTSA communication ID: 10222460
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015 â 2021 Model Year Mustang Convertible Vehicles Door Opens to Secondary Latch Position Submitting Owner Letter
Source components: LATCHES/LOCKS/LINKAGES.
Source record 10222460 at NHTSANHTSA communication ID: 10209364
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2014-2015 Model Year, Fusion and MKZ and 2015 Model Year Mustang Vehicles - Brake Stop Lamps Remain On. Under Safety Recall 22S02, in some of the affected vehicles, exposure to a high temperature, high humidity, and high salinity environment is causing the brake pedal "stop bumper" to disintegrate and fall off on some of the affected vehicles resulting in the brake stop lamps remaining on continuously, even when the brake pedal is not applied. If the brake pedal bumper is missing on automatic transmission vehicles, the engine can be started, and the transmission can shift out of park without depressing the brake pedal. For 22R01, owners will be instructed to request a repair under this regional program if their vehicle exhibits brake pedal concerns or if they are concerned about the brake pedals in their vehicles.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
Source record 10209364 at NHTSANHTSA communication ID: 10209209
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
Source components: EQUIPMENT · EQUIPMENT:MECHANICAL · SEATS.
Source record 10209209 at NHTSANHTSA communication ID: 10205726
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015 â 2021 Model Year Mustang Convertible Vehicles Door Opens to Secondary Latch Position n some of the affected vehicles, a front door latch may open to the secondary latched position while driving. While the door is in the secondary latched position the driver will notice wind noise from the door and a door ajar warning will appear on the instrument cluster. This concern does not result in a fully opened door while driving. The occupant can open the door normally using the door handle.
Source components: LATCHES/LOCKS/LINKAGES:DOORS:LATCH.
Source record 10205726 at NHTSANHTSA communication ID: 10201050
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM.
Source record 10201050 at NHTSANHTSA communication ID: 10201034
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
Source components: SERVICE BRAKES, ELECTRIC:SOFTWARE/PROGRAMMING.
Source record 10201034 at NHTSANHTSA communication ID: 10199536
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
Source components: SEATS.
Source record 10199536 at NHTSANHTSA communication ID: 10194428
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10194428 at NHTSANHTSA communication ID: 10191525
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2021 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150F (65àâÂÂC) or higher and engine speed is at idle up to approximately 1700 RPMs. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted.
Source components: ENGINE AND ENGINE COOLING.
Source record 10191525 at NHTSANHTSA communication ID: 10183567
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2011-2020 F-150/Mustang vehicles equipped with a 5.0L engine when installing a replacement secondary timing chain tensioner (6K254) or secondary timing chain guide (6K297), it is necessary to replace both components as a pair, using the latest level parts. Make sure to use secondary timing chain tensioner part number ML3Z-6K254-A and secondary timing chain guide part number ML3Z-6K297-A.
Source components: EQUIPMENT.
Source record 10183567 at NHTSANHTSA communication ID: 10183561
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 Mustang vehicles may exhibit a concern of the rear seat cover appearing loose or having the foam underneath the seat cover exposed. This condition is most apparent at the front outer corners of the lower seat cushion. This may be due to the seat cover coming loose. This can be corrected by tucking the corners of the seat cushion underneath the seat cover. Any loose seat cover material can also be tucked under the cover. Replacement of the seat cushion cover is not necessary to correct this condition.
Source components: EQUIPMENT · SEATS.
Source record 10183561 at NHTSANHTSA communication ID: 10181906
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 Mustang vehicles may exhibit a concern of no horizontal movement of the front power seats. This may be caused by a defective seat track motor or separation of the drive motor cable from the seat track. The seat track motor assembly is available separately (14547) and replacement of the complete seat frame assembly (9661711) may not be required. Refer to Workshop Manual, Section 501-10A for seat track motor removal.
Source components: SEATS · SEATS:FRONT ASSEMBLY:POWER ADJUST.
Source record 10181906 at NHTSANHTSA communication ID: 10180674
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150/Mustang, 2016-2020 Edge, 2016-2018 MKX and 2019-2020 Nautilus vehicles built on or before 18-Jan-2020 may exhibit a mirror click and/or ratcheting noise when using memory functions or easy entry/exit function. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM with the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14B291 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM:ADAS:BLINDSPOT:SOFTWARE · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10180674 at NHTSANHTSA communication ID: 10180428
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING.
Source record 10180428 at NHTSANHTSA communication ID: 10179333
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Mustang vehicles equipped with 3.7L and 5.0L built on or before 1-Apr-2017 equipped with a 6R80 transmission may exhibit a clunk or ping noise from the driveshaft when shifting from reverse to drive or drive to reverse. A revised driveshaft which has enhanced NVH characteristics has been released. For claiming, use causal part 4R602 and applicable labor operations in section 04 of the service labor time standards (SLTS) manual.
Source components: EQUIPMENT · POWER TRAIN.
Source record 10179333 at NHTSANHTSA communication ID: 10177863
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.
Source components: STRUCTURE.
Source record 10177863 at NHTSANHTSA communication ID: 10175895
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
Source components: SEATS · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
Source record 10175895 at NHTSANHTSA communication ID: 10172972
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
Source record 10172972 at NHTSANHTSA communication ID: 10169986
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: POWER TRAIN.
Source record 10169986 at NHTSANHTSA communication ID: 10167184
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Mustang vehicles equipped with a 5.0L engine may exhibit an oil leak from either valve cover gasket. This may be due to the valve covers warping due to excessive heat. To correct the condition, follow the Service Procedure steps to add fasteners to both valve covers.
Source components: ENGINE AND ENGINE COOLING.
Source record 10167184 at NHTSANHTSA communication ID: 10165702
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Mustang vehicles may experience an inoperative rear parking aid camera, luggage compartment lamp, luggage compartment lid release and/or poor satellite radio reception. This may be due to damage to the 14A005 harness in the area of the right side luggage compartment lid hinge. This concern may be accompanied by diagnostic trouble codes (DTCs) B115E, C1001, and B1A89. To resolve the condition, follow the Service Procedure steps to inspect and repair the wiring harness.
Source components: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA · ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10165702 at NHTSANHTSA communication ID: 10164429
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Mustang vehicles equipped with a 5.0L engine may exhibit an oil leak from either valve cover gasket. This may be due to the number of fasteners used to hold the valve cover onto the cylinder head. To correct the condition, follow the Service Procedure steps to add fasteners to both valve covers.
Source components: ENGINE AND ENGINE COOLING.
Source record 10164429 at NHTSANHTSA communication ID: 10164596
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10164596 at NHTSANHTSA communication ID: 10164497
NHTSA source summary · Original PDF not reviewed by Recallfolio
For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
Source components: ELECTRICAL SYSTEM.
Source record 10164497 at NHTSANHTSA communication ID: 10163593
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only be replaced for this condition when the 232 key table error message is present. If the 232 key table error is not present, follow normal diagnostics for the no crank condition. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM.
Source record 10163593 at NHTSANHTSA communication ID: 10162086
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 F-150/Mustang, 2015-2018 Edge/MKC, 2016-2018 MKX, 2013-2018 Explorer/Taurus/Flex/MKT, and 2017-2018 Fusion/MKZ/Continental vehicles built on or before 19-Oct-2017 may exhibit an inoperative adaptive cruise control, collision warning, and/or collision avoidance system with a Pre-Collision Assist Not Available, Collision Warning Not Available, and/or Adaptive Cruise Fault message present in the instrument panel cluster (IPC) and diagnostic trouble code (DTC) U3000:49 present in the cruise control module (CCM). To resolve the condition, reprogram the CCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 9E731 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · FORWARD COLLISION AVOIDANCE.
Source record 10162086 at NHTSANHTSA communication ID: 10162060
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 Mustang GT350/GT350R vehicles may exhibit a hesitation or surge in the vehicle with no diagnostic trouble codes (DTCs) present. This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has come loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. To resolve the condition, follow the Service Procedure steps to replace the output shaft flange nut.
Source components: POWER TRAIN · VEHICLE SPEED CONTROL:CRUISE CONTROL.
Source record 10162060 at NHTSANHTSA communication ID: 10160933
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 Mustangs may exhibit a driveline vibration after removal and installation of the drive pinion flange. This may be due to improper removal and installation of the drive pinion flange. It is critical to reinstall the drive pinion flange in the same orientation on the drive pinion stem as it was before it was removed. Mark the drive pinion flange and the drive pinion stem before removing the flange to make sure that it is reinstalled on the stem in the same orientation as it was before removal. Refer to Workshop Manual (WSM), Section 205-02.
Source components: POWER TRAIN · POWER TRAIN:DRIVELINE.
Source record 10160933 at NHTSANHTSA communication ID: 10160884
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 Mustang GT/GT350/GT350R Coupe vehicles equipped with Michelin Pilot Sport Cup 2 tires may exhibit tires which appear to have worn treads even when the tires are new or have low miles. This may be due to the fact that these tires come from the factory with a tread design which has shallower tread depth than most tires. There are also fewer grooves molded into the surface of the tire, with some areas of the tire showing no tread at all. Before condemning these tires as excessively worn, ensure that you are familiar with how these tires appear when new.
Source components: TIRES.
Source record 10160884 at NHTSANHTSA communication ID: 10160931
NHTSA source summary · Original PDF not reviewed by Recallfolio
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
Source components: POWER TRAIN.
Source record 10160931 at NHTSANHTSA communication ID: 10160880
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10160880 at NHTSANHTSA communication ID: 10159494
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
Source components: ENGINE.
Source record 10159494 at NHTSANHTSA communication ID: 10159489
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10159489 at NHTSANHTSA communication ID: 10156524
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 Mustang GT350/GT350R vehicles may exhibit a hesitation or surge in the vehicle with no diagnostic trouble codes (DTCs) present. This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has become loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. To resolve the condition, replace the output shaft flange.
Source components: POWER TRAIN.
Source record 10156524 at NHTSANHTSA communication ID: 10156561
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 Mustang vehicles may exhibit a concern of no horizontal movement of the front power seats. This may be caused by a defective seat track motor or separation of the drive motor cable from the seat track. The seat track motor assembly is available separately (14547) and replacement of the complete seat frame assembly (9661711) may not be required. Refer to Workshop Manual, Section 501-10A for seat track motor removal.
Source components: SEATS.
Source record 10156561 at NHTSANHTSA communication ID: 10156887
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM.
Source record 10156887 at NHTSANHTSA communication ID: 10155575
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM.
Source record 10155575 at NHTSANHTSA communication ID: 10156863
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
Source components: EQUIPMENT · STRUCTURE.
Source record 10156863 at NHTSANHTSA communication ID: 10155551
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
Source components: STRUCTURE.
Source record 10155551 at NHTSANHTSA communication ID: 10153969
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
Source components: EQUIPMENT.
Source record 10153969 at NHTSANHTSA communication ID: 10153932
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Mustang vehicles may experience an inoperative rear parking aid camera, luggage compartment lamp, luggage compartment lid release and/or poor satellite radio reception. This may be due to damage to the 14A005 harness in the area of the right side luggage compartment lid hinge. This concern may be accompanied by diagnostic trouble codes (DTCs) B115E, C1001, and B1A89. Follow the Service Procedure steps to correct the condition.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10153932 at NHTSANHTSA communication ID: 10153931
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
Source components: EQUIPMENT · SEATS.
Source record 10153931 at NHTSANHTSA communication ID: 10152473
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
Source record 10152473 at NHTSANHTSA communication ID: 10152464
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
Source components: ELECTRICAL SYSTEM.
Source record 10152464 at NHTSANHTSA communication ID: 10148712
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Mustang GT350/GT350R vehicles may exhibit a hesitation or surge in the vehicle with no DTCs present. This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has become loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. Follow the Service Procedure steps to correct the condition.
Source components: POWER TRAIN.
Source record 10148712 at NHTSANHTSA communication ID: 10149752
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Mustang GT350/GT350R vehicles built before 30-Jun-2017 may exhibit an Exhaust Mode Selection Not Available or Drive Mode Not Available message displayed in the instrument panel cluster (IPC) when attempting to change the exhaust mode or drive mode. This may be due to an exhaust tailpipe valve that has frozen in place when the vehicle was started or driven in temperatures at or below freezing. Follow the Service Procedure steps to correct the condition.
Source components: ELECTRICAL SYSTEM.
Source record 10149752 at NHTSANHTSA communication ID: 10149762
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Shelby GT350 and GT350R vehicles may require brake service or repairs to be performed. The vehicles should not have the brake rotors machined when servicing the brake system. Replacement of brake rotors is the only acceptable service of brake rotors on GT350 and GT350R vehicles. GT350 and GT350R vehicles are equipped with a brake system designed for high speed and superior fade resistance. Occasional brake squeal and elevated levels of brake dust may occur. This is normal and does not affect brake system performance. Refer to the Workshop Manual (WSM) Section 206-00 and the Mustang Owner's Manual and the Shelby GT350 Owner's Manual Supplement for further information.
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10149762 at NHTSANHTSA communication ID: 10144947
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
Source components: STEERING.
Source record 10144947 at NHTSANHTSA communication ID: 10144920
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Mustang vehicles may exhibit poor A/C performance. If the cause of this is found to be a refrigerant leak from the evaporator, it is recommended to replace only the evaporator as opposed to the entire climate control housing. Follow the Service Procedure steps to correct the condition.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10144920 at NHTSANHTSA communication ID: 10144221
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Mustang vehicles equipped with a 5.0L engine may exhibit an illuminated MIL with diagnostic trouble code (DTC) P0300 through P0308 present. A noticeable misfire may or may not accompany these DTCs. If normal diagnostics do not lead to a root cause for this concern, remove the intake manifold from the vehicle and verify the intake manifold runner control (IMRC) plates move when the IMRC actuators are moved by hand. These plates are visible through the outlet ports of the intake manifold. If the IMRC plates do not move when the IMRC actuators are moved by hand, the intake manifold should be replaced. For claiming, use causal part 9424 and applicable labor operations in Section 9 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE · EQUIPMENT.
Source record 10144221 at NHTSANHTSA communication ID: 10144218
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015 and 2016 Mustang vehicles built on or before 4/22/2016 may exhibit a partial outage of the rear tail, turn signal or stop lamps following a vehicle start with a low battery. This may be accompanied by any combination of DTCs B1271, B1272, B1273, B1274, B1275 and B1276. The condition typically clears on vehicle restart. Reprogram the BCMB module to the latest calibration using IDS release 110.01 or higher. Calibration files may also be obtained at www.motorcraftservice.com. Use applicable labor operations from Section 10 of the SLTS manual and use causal part 13C788.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10144218 at NHTSANHTSA communication ID: 10143098
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Mustang GT350s may exhibit an engine oil leak that appears to be originating from the oil filter adapter or oil cooler. If the leak appears to be originating from the oil cooler, be aware that the leak may actually be originating from the oil filter adapter, and oil may run down the oil cooler tubes and drip off of the cooler, making it appear that the leak is originating from the oil cooler. If the true source of the leak is caused by a damaged O-ring where the oil cooler tubes meet the oil filter adapter, be aware that these O-rings are now available as a separate service part from the oil cooler tubes. Replacement O-rings can be ordered using part number FR3Z-00815-A. For claiming, use causal part 6B850 and applicable labor operations in Section 6 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
Source record 10143098 at NHTSANHTSA communication ID: 10143077
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Mustang vehicles may exhibit poor A/C performance. If the cause of this is found to be a refrigerant leak from the evaporator, it is recommended to replace only the evaporator as opposed to the entire climate control housing. Follow the Service Procedure steps to correct the condition.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10143077 at NHTSANHTSA communication ID: 10137128
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Mustang vehicles equipped with SYNC 3 may exhibit inoperative USB ports with the diagnostic trouble code (DTC) B1252:13 stored in the accessory protocol interface module (APIM.) This may be due to a loose connection or damage present on the cable which connects the APIM to the media hub. Follow normal Workshop Manual (WSM) diagnosis to correct this condition, while paying close attention to any damage or loose connections which may be present on this cable.
Source components: EQUIPMENT.
Source record 10137128 at NHTSANHTSA communication ID: 10137113
NHTSA source summary · Original PDF not reviewed by Recallfolio
Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
Source components: EQUIPMENT.
Source record 10137113 at NHTSANHTSA communication ID: 10137112
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Mustang vehicles may exhibit a concern of no horizontal movement of the front power seats. This may be caused by a defective seat track motor or separation of the drive motor cable from the seat track. The seat track motor assembly is available separately (14547) and replacement of the complete seat frame assembly (9661711) may not be required. Refer to Workshop Manual, Section 501-10A for seat track motor removal.
Source components: SEATS.
Source record 10137112 at NHTSANHTSA communication ID: 10137079
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Mustang GT350 vehicles built on or before 26-Feb-2018 may exhibit an excessive panel gap where the rear bumper cover meets the rear quarter panels on either side of the vehicle. This may be due to the method used to fasten the rear bumper cover to the vehicle. Follow the Service Procedure steps to correct the condition.
Source components: STRUCTURE:BODY:BUMPERS.
Source record 10137079 at NHTSANHTSA communication ID: 10137091
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Mustang vehicles built on or before 2-Sep-2016 may exhibit poor A/C performance. If a low refrigerant charge is confirmed and there are no other obvious signs of a refrigerant leak, suspect the evaporator to be the source of the leak.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10137091 at NHTSANHTSA communication ID: 10136597
NHTSA source summary · Original PDF not reviewed by Recallfolio
2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10136597 at NHTSANHTSA communication ID: 10136592
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10136592 at NHTSANHTSA communication ID: 10136574
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Mustang vehicles with a convertible top may exhibit a condition where the top sags on one or both sides near the rear glass due to broken tension rod clips. Follow the Service Procedure steps to correct the condition.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:BODY:ROOF AND PILLARS.
Source record 10136574 at NHTSANHTSA communication ID: 10140324
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, Mustang and Transit vehicles built on or before 01-Dec-2017 may have a concern of no airflow from the climate control vents. This may be caused by a seized or sticking A/C clutch. This can be repaired by replacing only the A/C clutch (19D786/19D784). The compressor assembly (19703) may not be required. Refer to Workshop Manual, Section 412-00 for A/C clutch removal. It may be necessary to lightly tap around the stuck area of the clutch with a rubber mallet to free it from the pulley for removal. Refer to applicable labor operations from Section 11 of the SLTS maunual when replacing the A/C clutch.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10140324 at NHTSANHTSA communication ID: 10138525
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, Mustang and Transit vehicles built on or before 01-Dec-2017 may have a concern of no airflow from the climate control vents. This may be caused by a seized or sticking A/C clutch. This can be repaired by replacing only the A/C clutch (19D786/19D784). The compressor assembly (19703) may not be required. Refer to Workshop Manual, Section 412-00 for A/C clutch removal. It may be necessary to lightly tap around the stuck area of the clutch with a rubber mallet to free it from the pulley for removal. Refer to applicable labor operations from Section 11 of the SLTS maunual when replacing the A/C clutch.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10138525 at NHTSANHTSA communication ID: 10140311
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Mustang Convertibles built on or before 1-Feb-2017 may exhibit wear marks or damage to the exterior surface of the convertible top in the area of the front outer edges. This may be due to contact between the convertible top and the tonneau covers that may be installed on the vehicle by the customer when the top is in the open position. If the tonneau covers have been installed on the vehicle, and the wear/damage is located in the area where the tonneau covers overlap the convertible top, replace the convertible top material. Refer to WSM, Section 501-18. Discard the original tonneau covers, and supply the customer with new tonneau covers, part numbers FR3Z-7631004-CB and FR3Z-7631005-CB. For claiming, use causal part 7631004 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE.
Source record 10140311 at NHTSANHTSA communication ID: 10138512
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Mustang Convertibles built on or before 1-Feb-2017 may exhibit wear marks or damage to the exterior surface of the convertible top in the area of the front outer edges. This may be due to contact between the convertible top and the tonneau covers that may be installed on the vehicle by the customer when the top is in the open position. If the tonneau covers have been installed on the vehicle, and the wear/damage is located in the area where the tonneau covers overlap the convertible top, replace the convertible top material. Refer to WSM, Section 501-18. Discard the original tonneau covers, and supply the customer with new tonneau covers, part numbers FR3Z-7631004-CB and FR3Z-7631005-CB. For claiming, use causal part 7631004 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual.
Source components: VISIBILITY:SUN/MOON ROOF ASSEMBLY.
Source record 10138512 at NHTSANHTSA communication ID: 10127405
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
Source record 10127405 at NHTSANHTSA communication ID: 10109017
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015 - 2017 Mustang vehicles may experience exhaust alignment issues. Before replacement of exhaust system components for this issue, align the exhaust system following the workshop manual (WSM) procedure found in section 309-00, Muffler and Tailpipe removal and installation. The WSM procedure has been revised with updated steps to resolve these issues.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
Source record 10109017 at NHTSANHTSA communication ID: 10100524
NHTSA source summary · Original PDF not reviewed by Recallfolio
CERTAIN 2015 THROUGH 2017 MODEL YEAR MUSTANG SHELBY® GT350 AND GT350R VEHICLES - COMPLIMENTARY OIL FILTER WRENCH.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10100524 at NHTSANHTSA communication ID: 10099463
NHTSA source summary · Original PDF not reviewed by Recallfolio
2009-2017 VEHICLES EQUIPPED WITH A 6R80, 6R100, 6R140 AUTOMATIC TRANSMISSION HAVE AN UPDATED MAIN CONTROL VALVE BODY OVERHAUL PROCEDURE. REFER TO WORKSHOP MANUAL (WSM), SECTION 307-01 FOR MAIN CONTROL VALVE BODY (7A100) OVERHAUL PROCEDURES. NOT ALL VALVE BODIES REQUIRE REPLACEMENT. INSPECT THE VALVE BODY BORES, SPRINGS AND VALVES AS DIRECTED DURING DIAGNOSIS AND REPAIR. REFER TO GENERAL SERVICE BULLETIN (GSB) G0000093 AUTOMATIC TRANSMISSION MAIN CONTROL INSPECTION FOR A VIDEO CLIP TO AID IN THE DIAGNOSIS OF THESE REPAIRS.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10099463 at NHTSANHTSA communication ID: 10095224
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015 EDGE,MUSTANG AND F150 VEHICLES WITH A 4" DISPLAY MAY EXHIBIT A 24 HOUR CLOCK DISPLAY THAT RESETS ITSELF TO A 12 HOUR DISPLAY AFTER CYCLING THE IGNITION KEY. TO CORRECT THE CONCERN, REFLASH THE FRONT CONTROL DISPLAY INTERFACE MODULE (FCDIM) TO THE LATEST CALIBRATION USING IDS VERSION 103.05 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE CAUSAL COMPONENT 10D885 AND APPLICABLE 12652A LABOR OPERATIONS FROM SECTION 10 OF THE SLTS MANUAL FOR REFLASH ONLY.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10095224 at NHTSANHTSA communication ID: 10095184
NHTSA source summary · Original PDF not reviewed by Recallfolio
REPLACING THE ORIGINAL EQUIPMENT SYNC/NAVIGATION SYSTEM WITH EITHER AN AFTERMARKET SYNC/NAVIGATION KIT OR MODIFYING ORIGINAL SYNC/NAVIGATION PARTS TO PROVIDE ADDITIONAL FEATURES IS NOT RECOMMENDED NOR SUPPORTED ON ANY FORD, MERCURY OR LINCOLN VEHICLE. ONLY APPROVED GENUINE FORD ACCESSORIES OR ORIGINALLY INSTALLED SYSTEMS ARE SUPPORTED AND CERTIFIED TO FUNCTION CORRECTLY WITH OTHER VEHICLE SYSTEMS. IF YOU SUSPECT A SYSTEM HAS BEEN MODIFIED, THE FOLLOWING RESOURCES CAN BE USED TO VERIFY ORIGINAL EQUIPMENT: MONRONEY LABEL (WINDOW STICKER), PROFESSIONAL TECHNICIAN SOCIETY (PTS) OASIS TAB SELECT SYNC OR HVBOM. FOR GENUINE FORD ACCESSORIES USE: PTS WORKSHOP TAB SELECT DEALER INSTALLED ACCESSORY OR ACCESSORY INSTALLATION.
Source components: EQUIPMENT.
Source record 10095184 at NHTSANHTSA communication ID: 10095154
NHTSA source summary · Original PDF not reviewed by Recallfolio
TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.
Source components: ENGINE.
Source record 10095154 at NHTSANHTSA communication ID: 10094612
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2016 EDGE WITH 2.0L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI), 2015-2016 MUSTANG AND F-150 WITH 5.0L ENGINE AND 2016 EXPLORER EQUIPPED WITH 2.3L GTDI ENGINE MAY EXHIBIT OIL LEAK AT ENGINE OIL PRESSURE (EOP) SENSOR THREADS. IT IS NOT REQUIRED TO REPLACE THE SENSOR IF IT IS LEAKING FROM THE THREADS. REMOVE AND RESEAL THE EOP SENSOR, REFER TO WORKSHOP MANUAL (WSM), SECTIONS 303-14. CHECK THE OIL LEVEL AND TOP OFF AS NECESSARY. REFER TO WSM, SECTION 303-01. USE CAUSAL PART 9278 AND APPLICABLE LABOR OPERATIONS IN SECTION 09 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL
Source components: ENGINE.
Source record 10094612 at NHTSA