2021 Ford MUSTANG MACH E Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–200 of 324, ordered newest first. Dated records on this page: Aug 22, 2022–Jan 15, 2024.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jan 15, 2024Service Bulletin/Repair Instructions
TSB 24-2012
NHTSA communication ID: 10249758
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mach-E vehicles may exhibit the drive mode default to normal mode while driving and Drive Mode Not Available message displays in the center display screen with or without diagnostic trouble code (DTC) U0253 stored in the anti-lock brake system module (ABS). This may be due to the software in the SYNC module (APIM). The APIM software update that addresses the symptom listed in this bulletin may have been sent via Ford Power-Up software updates delivered over-the-air (OTA) to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history. If an update to the APIM has successfully completed recently and the customer is reporting the symptoms are no longer present, this article may not apply.
Source components: BACK OVER PREVENTION:SOFTWARE · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E vehicles built on or before 24-Jun-2023 may exhibit a condition where the high voltage battery slow charging or does not charge while using a level 1 or level 2 electric vehicle supply equipment (EVSE) after an over the air (OTA) update. This may be due to the software in the secondary on-board diagnostic control module A (SOBDM)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2021-2024 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit a Please Check Surroundings For Safety or Full View Not Available message when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E, 2022-2023 E-Transit/F-150 Lightning vehicles may have diagnostic trouble code (DTC) P1A3C stored in the off-board charger controller module (OBCC). The P1A3C is commonly set due to an interruption of the direct current (DC) fast charging process and should be disregarded. All other DTCs stored in the OBCC are to be addressed using applicable publications and/or normal diagnostics found in Workshop Manual, Section 414-03B.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update SU7 P1 for 2021- 2023 MY Mach E vehicles is now available. Quality improvements include: - Reduces erroneous BLIS warning 21 MY: - Increases availability of BlueCruise. Ignition reset will not be necessary to reengage BlueCriuse. - Reduces false eyes-off warnings - Improved OTA success rate 21-22 MY: - Improved Reverse Brake assist availability - Customer is instructed to exit the vehicle when a battery hazard is detected - Enables the e-release feature on the front trunk.
Source components: ELECTRICAL SYSTEM:ADAS:AUTONOMOUS/SELF DRIVING:SOFTWARE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E vehicles may exhibit a condition where the high voltage battery stops charging when connected to level 1 or level 2 chargers with an illuminated malfunction indicator lamp (MIL) and diagnostic trouble code (DTC) P2C94 stored in the secondary on-board diagnostic control module A (SOBDM). This may be due to the software in the SOBDM. To correct this condition, follow the Service Procedure to reprogram the powertrain control module (PCM).
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2326 to remove a DTC from the Issue and Action. Some 2021-2023 Mustang Mach-E built on or before 15-Sep-2023 and 2022-2023 E-Transit vehicles may experience an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) U3000:16, U3000:64, U3000:04 and/or U3000:45 in the off-board charging controller (OBCC) module and the high voltage (HV) battery will not charge using a level 3 direct current (DC) fast charging station/electrical vehicle supply equipment (EVSE). This may be due to the software in the OBCC. To correct the condition, follow the Service Procedure to reprogram the OBCC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mach-E vehicles may experience an exterior charge status indicator not illuminating the blue charging segments after an over the air (OTA) update. This may be due to the software in the SYNC module (APIM). To correct the condition, follow the Service Procedure steps to reprogram the APIM. NOTE: The APIM software update that addresses the symptom listed in this bulletin may have been sent via Ford Power-Up software updates delivered over- the-air (OTA) to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history. If an update to the APIM has successfully completed recently and the customer is reporting the symptoms are no longer present, this article may not apply.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mach-E vehicles built on or before 29-May-2023 may experience an alarm activation even after the motion sensor function has been disabled through the pop-up menu at ignition off. This may be due to the software in the SYNC module (APIM). To correct the condition, follow the Service Procedure steps to reprogram the APIM. NOTE: The APIM software update that addresses the symptom listed in this bulletin may have been sent via Ford Power-Up software updates delivered over-the-air (OTA) to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history. If an update to the APIM has successfully completed recently and the customer is reporting the symptoms are no longer present, this article may not apply.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2307 to update the Service Procedure. Some 2021-2023 Mustang Mach-E vehicles built on or before 29-Sep-2023 may experience a water leak into the liftgate. This may be due to water intruding past the seals on the liftgate mounted rear lamp assemblies. To correct the condition, follow the Service Procedure to seal the lamp cavities.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2257 to update the Parts List. Some 2021-2023 Mustang Mach-E vehicles built on or before 17-Mar-2023 may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P0563, P0ADA, P0ADE, P0AA1, P0AA4, P0AA5, P0AA2, P0D10, P0D0F, and/or P0C78 stored in battery energy control module (BECM). It may also have a low/discharged 12V battery and/or display a Stop Safely Now message in the instrument panel cluster (IPC). This may be due to the high voltage battery junction box (HVBJB). To correct the condition, follow the Service Procedure to replace the HVBJB and reprogram the BECM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E, 2022-2023 F-150 Lightning/e-Transit vehicles may exhibit a concern where the vehicle is unable to achieve 100 percent state of charge immediately after high voltage (HV) battery module balancing and replacement. This may be due to the battery energy control module (BECM) adjusting the cell balance (conditioning) of the battery module and should be corrected within 22 days. If the vehicle otherwise functions as designed with no related diagnostic trouble codes (DTC) setting, this concern will be corrected automatically with no further actions required by the technician.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update SU6 P3 for 2021-2023 MACH E vehicles is now available. Quality Improvements include: - Enable electric return of hood latch release actuator - Corrects erroneous "frunk service required" warning post OTA. - Corrects alarm going off during an OTA download . - improved interior windsheld fogging and heater performance when driving in freezing temperatures - Improved Cold DC Fast Charging and heat sharing/smart heating. - Removal of cause of chime related DTC set against AHU. - Hands-Free to BlueCruise text update. - Adds 3 chimes for Over Speeding situation. - Adds chime for speed limit change. - Adds text box "Hold for Speed Warning OFF" - Introduces a more aggressive series of hood ajar warnings/chimes that trigger at lower speed than the current implementation - The customer is instructed to exit the vehicle when a battery hazard is detected. - IPC software addressing traction control toggle, BLIS and ISA presonaliztion, MyTrip distance reset, Low Tire pressure incorrect reading, and PWM buzz noise elimination. - Provides Yield and No Entry graphic display for Traffic Sign recognition. - Removes Tollbooth Mode - Adds a "some display features may be temporarily unavailable" message to the SYNC screen when a SYNC update is installing. - Profiles (Enhanced Memory) will not be stuck as Guest - Improved "Ask on Exit" pop- up functionality - Selectable Drive Modes - prevent default to normal mode due to loss of communication with SYNC - Improved charge status indication feedback while plugged in.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Recall re-engagement email to customers who have not completed their recall. The message will provide a link to the Ford VIN recall look up tool to show the customer open recalls on their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Recall re-engagement email to customers who have not completed their recall. The message will provide a link to the Ford VIN recall look up tool to show the customer open recalls on their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Recall re-engagement email to customers who have not completed their recall. The message will provide a link to the Ford VIN recall look up tool to show the customer open recalls on their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Recall re-engagement email to customers who have not completed their recall. The message will provide a link to the Ford VIN recall look up tool to show the customer open recalls on their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Recall re-engagement email to customers who have not completed their recall. The message will provide a link to the Ford VIN recall look up tool to show the customer open recalls on their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update SU6 P2 for Mach E is now available. Quality Improvments include: - Improved State of Charge accuracy during AC charging. - Updated messaging: customer is instructed to exit the vehicle when a battery hazard is detected. - NVH improvment addressing Front Drive Unit Whine whle coasting. - Charge settings updated via Ford Pass will not revert back to previous settings due to chip shortage. This change allows use of Bussed Electrical Center without the low range chip in service on vehicles in the field. - At high State of Charge, the displayed Distance to Empty will now show what the vehicle is capable of under the current environmental conditions, instead of the estimated capability based on driver history. - Software update to prevent localized melting of charge port pins(reference: FSA 23B50).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2496 to update the Title and production clean date. Some 2021-2023 Mustang Mach-E built on or before 15-Sep-2023 and 2022-2023 E-Transit vehicles may experience an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P1A3C, U3000:16, U3000:64, U3000:04 and/or U3000:45 in the off-board charging controller (OBCC) module and the high voltage (HV) battery will not charge using a level 3 direct current (DC) fast charging station/electrical vehicle supply equipment (EVSE). This may be due to OBCC software. To correct the condition, follow the Service Procedure to reprogram the OBCC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Program 23B50 Certain 2021-2023 Model Year Mustang Mach-E, 2022-2023 Model Year E-Transit, and 2023 F-150 Lightning Vehicles - Charge Cord Stuck â Reprogram Battery Charge Control Module
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION BATTERY THERMAL:MANAGEMENT:SOFTWARE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E vehicles may experience an alarm activation even after the motion sensor function has been disabled through the pop-up menu at ignition off. If the customer wants to turn off the motion sensors for a key cycle, they can go to the center display screen: Vehicle Settings Alarm System Motion Sensors off. The motion sensors will be re-enabled on the next key cycle. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in November 2023. Monitor OASIS for additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E vehicles may experience an exterior charge status indicator not illuminating the blue charging segments after an over the air (OTA) update. Confirm if the Charge Port Light toggle button is not present in the center display screen by selecting Vehicle Icon Controls Access Charge Port Light toggle button, as this button has been removed after OTA update. Replacing the charge port and/or the battery charger control module (BCCM) is not recommended. This condition does not affect charge behavior and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in November 2023. Monitor OASIS for additional information.
Source components: ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION BATTERY:MANAGEMENT SYSTEM/ENERGY CONTROL MODULE (BMS/BECM):SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
his article supersedes TSB 22-2446 to update the Service Procedure. Some 2021 Mustang Mach-E vehicles built on or before 07-Jul-2021 may experience Frunk System Fault Service Required message displayed in the IPC after performing body control module (BCM) update. This may be due to the software in the BCM. To correct the condition, follow the Service Procedure to reprogram the SYNC module (APIM), BCM and front trunk release module (FTRM). NOTE: The APIM software update that addresses the symptom listed in this article may have been delivered over-the-air (OTA) via Ford Power-Up software updates to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Software Update SU6 P1 for 2021 - 2023 Mach E is now available. Quality improvements include: -Improved ""Ask on Exit"" pop- up functionality '- Adds a ""some display features may be temporarily unavailable"" message to the SYNC screen when a SYNC update is installing. - Selectable Drive Modes - prevent default to normal mode due to loss of communication with SYNC - Improved Profiles (Enhanced Memory) - prevent getting stuck in GUEST. - Improved feedback of vehicle charging behavior when plugging-in.
Source components: ELECTRICAL SYSTEM:ADAS:DRIVER MONITORING:SOFTWARE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Ford and Lincoln vehicles may exhibit DTCs U2100 and/or U3002 stored in the cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement. DTC U2100 may set when the module has not been properly configured after replacement. DTC U3002 may set when the module has been configured with the incorrect VIN. To correct this condition, verify that the module storing the DTC has been installed following the applicable Workshop Manual (WSM) Removal and Installation procedure. If the DTC is still stored, download and run the Vehicle Identification Number (VIN) Write application found under Toolbox, Multi-Module tab in the Ford Diagnosis and Repair System (FDRS).
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Priority Update 23- PU0722-DC-CHG3 for 2021- 2022 MACH E vehicles is now available. Quality Improvements include: -Robustness actions to improve DC fast charging performance/success rate"
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E and 2022-2023 E-Transit vehicles may exhibit an inability to clear diagnostic trouble codes (DTCs) P0ADA, P0ADE, P0AA1, and/or P0AA4 stored in the battery energy control module (BECM) after high voltage battery junction box (HVBJB) replacement. To correct the condition, download and run the BECM - Reset Diagnostic Trouble Code (DTC) Occurrence Counter application in Ford Diagnosis and Repair System (FDRS). If the concern persists, refer to Workshop Manual (WSM), Section 414-03A for normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E vehicles built on or before 17-Mar-2023 may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P0563, P0ADA, P0ADE, P0AA1, P0AA4, P0AA5, P0AA2, P0D10, P0D0F, and/or P0C78 stored in battery energy control module (BECM). It may also have a low/discharged 12V battery and/or display a Stop Safely Now message in the instrument panel cluster (IPC). This may be due to the high voltage battery junction box (HVBJB). To correct the condition, follow the Service Procedure to replace the HVBJB and reprogram the BECM.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION BATTERY:MANAGEMENT SYSTEM/ENERGY CONTROL MODULE (BMS/BECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update 5 P2 for 2021- 2022 MACH E vehicles is now available. Quality improvements include: - Improved motion sensor on/off selection pop- up when exiting. - Selectable Drive Modes communication robustness action to prevent unintended return to default drive mode. - Improved charge status indication feedback while plugged in. - Add in-vehicle message on infotainment screen to inform customer that some display features may be unavailable while SYNC is rebooting during SYNC OTA update installation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E vehicles may exhibit an exterior charge status indicator blinking red with diagnostic trouble code (DTC) P0E5F stored in the secondary on-board diagnostic control module A (SOBDM) and the high voltage battery cannot be charged using a 48-amp AC level 2 charger. The vehicle may also exhibit in the next key cycle a Service Soon message in the instrument panel cluster (IPC) and a FordPass warning message. This may be due to an excessive charge port temperature. The concern may not be present when using a 32-amp or lower AC level 2 charger. To correct this condition, remove and replace the charge port. Refer to Workshop Manual (WSM) Section, 414-03B. For claiming, use causal part 14A303 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2168 to update the vehicle line affected. Some 2021-2022 Mustang Mach-E (non-GT) vehicles equipped with all-wheel drive (AWD) may exhibit a whine noise from the front drive unit when driving steady at speeds between 30-40 mph (48-64 km/h) without diagnostic trouble codes (DTCs) present. This may be due to software parameters. To correct the condition, follow the Service Procedure to reprogram the powertrain control module (PCM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
In various 2017-2023 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Ford and Lincoln vehicles may exhibit a condition where the high voltage battery stops charging when connected to level 1 or level 2 chargers with an illuminated malfunction indicator lamp (MIL) and diagnostic trouble code (DTC) P2C94 stored in the secondary on-board diagnostic control module A (SOBDM). To restore charging capability, disconnect the off-board charging station charge handle from the vehicle charge port and reconnect. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in August 2023. Replacement of the SOBDM will not resolve this condition. Monitor OASIS for additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Escape built on/before 23-Nov-2021, 2021 F-150 built on/before 08-Oct-2021, 2021 Mustang Mach-E built on/before 29-Mar-2021, 2021 Expedition built on/before 05-Aug-2021, 2021 Explorer built on/before 27-Sep-2021 and 2020-2022 Edge may exhibit a concern of the audio system does not power on, no sound from audio speakers, chimes default to coming through the instrument cluster, no communication with audio control module (ACM) or digital signal processor (DSP) module, and/or diagnostic trouble code (DTC) U0184, U0237 and/or U0238. To correct the condition, perform a hard reset of the DSP by disconnecting the 12-volt battery. Reprogram the DSP module using the latest version of the appropriate Ford diagnostic scan tool. For claiming, use causal part 18B849 and any applicable labor operations in Section 10 of the Service Labor Time Standards Manual.
Source components: BACK OVER PREVENTION:SOFTWARE · EQUIPMENT:APPLIANCE:TV/RADIO/SPEAKERS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E/F-150, 2022-2023 Expedition/Navigator and 2023 Corsair vehicles may exhibit a Driver Monitoring Camera Blocked message and/or DTCs B115E:97, B15E1:97 and/or B15E2:97 stored in the driver status monitor camera module (CMR). These DTCs should be disregarded unless it is a DTC with a status byte 8F. Other status bytes should be disregarded as they may be caused by a camera obstruction such as driver position, aftermarket devices or dust on the camera. To clear the DTCs, remove anything obstructing the view of the camera and light emitting diodes (LEDs), place the steering wheel in the center position and close the driver door. Connect Ford Diagnosis and Repair System (FDRS) and clear the DTCs. Turn the ignition off and wait 10 seconds. Turn the ignition on and wait 1 minute. Perform the CMR self-test and reevaluate if DTCs persist.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021-2023 Model Year Mustang Mach-E Door Control Module Update Some of the affected vehicles may exhibit a false alarm activation and/or a warning message in the FordPass application when the doors are locked
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021-2022 Model Year Mustang Mach-E and 2022 Model Year E-Transit Vehicles - Off-Board Charger Controller Module Programming Technical Information update
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E vehicles built on or before 21-Apr-2023 may exhibit a false alarm activation and/or warning message in the FordPass application when the doors are locked. This may be due to the software in the door latch control module E (DCME), door latch control module F (DCMF), door latch control module G (DCMG) and/or door latch control module H (DCMH). To correct the condition, download and run the door control module software update application for each module one at a time using the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 58219A65 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E and 2022-2023 E-Transit vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P0ADA, P0ADE, P0AA1, and/or P0AA4 stored in the battery energy control module (BECM) after high voltage battery junction box (HVBJB) replacement. Vehicle may also exhibit reduced powertrain performance and/or a Stop Safely Now message displayed in the instrument panel cluster (IPC) and/or High-Voltage Battery Warning message in the FordPass application. This may be due to the BECM software. To correct the condition, download and run the BECM - Reset Diagnostic Trouble Code (DTC) Occurrence Counter application in Ford Diagnosis and Repair System (FDRS). If the concern persists, refer to Workshop Manual (WSM), Section 414-03A for normal diagnostics. Some 2021-2023 Mustang Mach-E and 2022-2023 E-Transit vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P0ADA, P0ADE, P0AA1, and/or P0AA4 stored in the battery energy control module (BECM) after high voltage battery junction box (HVBJB) replacement. Vehicle may also exhibit reduced powertrain performance and/or a Stop Safely Now message displayed in the instrument panel cluster (IPC) and/or High-Voltage Battery Warning message in the FordPass application. This may be due to the BECM software. To correct the condition, download and run the BECM - Reset Diagnostic Trouble Code (DTC) Occurrence Counter application in Ford Diagnosis and Repair System (FDRS). If the concern persists, refer to Workshop Manual (WSM), Section 414-03A for normal diagnostics
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E vehicles built on or before 19-Aug-2022 may exhibit a condition of intermittent headlamp operation while the vehicle is off and have diagnostic trouble code (DTC) B1533 stored in the body control module (BCM). This may be due to the internal logic within the headlamp switch. To correct this condition, replace the headlamp switch (service base PN: 11654). Refer Workshop Manual, Section 417-01. For claiming, use casual part 11654 and the applicable labor operations of Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Mustang Mach-E (Non-GT) vehicles built on or before 22-Jul-2021 may exhibit a buzz noise from the instrument panel cluster (IPC) that changes with the brightness setting. This may be due to the internal hardware in the IPC. To correct the condition, replace the IPC. Refer to Workshop Manual, Section 413-01. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021-2022 Model Year Mustang Mach-E and 2022 Model Year E-Transit Vehicles - Off-Board Charger Controller Module Programming Some Mustang Mach-E, and E-Transit battery electric vehicles (BEV) may experience inability to charge at certain charging stations
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:PROPULSION SYSTEM:CHARGING:MODULE:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Mustang Mach-E and F-150 vehicles may fail PMI for the IPMA using the Ford Diagnosis and Repair System (FDRS) with an error stating Procedure Unsuccesful - GetFlashActionPartNumbers Unable To Obtain Flash Action Part Numbers From Available Topology if the power steering control module (PSCM), cruise control module (CCM), camera module - rear (CMR) and/or instrument panel cluster (IPC) are not at their latest software level prior to attempting PMI. To correct this condition follow the Service Procedure to update each of the modules necessary to complete PMI for the IPMA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E vehicles equipped with all-wheel drive (AWD) may exhibit a whine noise from the front drive unit when driving steady speed between 30-40 mph (48-64 km/h) without diagnostic trouble codes (DTCs) present. This may be due to software parameters. To correct the condition, follow the Service Procedure to reprogram the powertrain control module (PCM)
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update 4 P2 for 2021- 2023 Model Year Mach E vehicles is now available. Quality improvements include: Remove Reverse Brake Assist unavailable warning Remove Beltminder Tollbooth Mode Remove incorrect frunk service now pop- up. Improves hood ajar warnings/ chimes. New thermal parameters added for increased powertrain component protection. Ford Pass Charge settings - will not revert back to previous settings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Priority Update 23-PU0415-BLM-FX-VIS for 2021 - 2023 Mach E vehicles is now available Quality Improvements include: -Phone as a Key Passive Entry improvement
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021 Model Year Mustang Mach E Gateway Module Reprogramming In all the affected vehicles, the Gateway Module (GWM) may have lost internet connection after an OTA update. This may cause the vehicle to display a No Driver Logged message on the screen
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021 Model Year F-150 and Mustang Mach-E Vehicles with Ford Co-Pilot360 Active 2.0 Prep Package (Includes Ford BlueCruise Prep Kit) BlueCruise Module Programming REASON FOR THIS SUPPLEMENT Affected Vehicles: Added US population of affected vehicles Service Action: Updates regarding Technical Information Pick-up and Delivery: Added pick-up and delivery information for participating dealers Mobile Repair: Assessment Level is Not Mobile Service Capable due to time requirements Claims Preparation and Submission: Pick-up and Delivery information added Owner Notification Mailing Schedule: Updated mail date for revised owner letter Labor Allowances: Updated with TSB 22-2404 Technical Information: Added and removed steps
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E vehicles may exhibit various driver assistance system warning messages or inoperative features and/or diagnostic trouble code (DTC) U3000:49 stored in the image processing module A (IPMA) that will not clear and not be stored in the vehicle's history. DTCs C1001:31 and/or U3000:89 may be stored in the IPMA, but may have recently been cleared and stored in the vehicle's history. This may be due to a connection issue between the IPMA Camera and the IPMA. To correct the condition, perform the following service procedure to repair the connection and reset the IPMA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Priority Update 23-PU0407-BCDC-FX for 2021 Mach E vehicles is now available: Quality Improvements include: -Restores driver assist functionality on specific VINs that may have a configuration mismatch with the server
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E vehicles may exhibit a condition of intermittent headlamp operation while the vehicle is OFF and have diagnostic trouble code (DTC) B1533 stored in the body control module (BCM). This may be due to the internal logic within the headlamp switch. Switch and/or module replacement will not resolve this condition. Headlamp operation is not affected while the vehicle is ON. A new headlamp switch is currently under development to correct this condition. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and schedule a follow-up appointment in July 2023, when parts are expected to become available. Follow up with the customer to confirm the appointment once OASIS is updated with the repair information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E, 2022-2023 F-150 Lightning vehicles may experience an exterior charge status indicator not illuminating the blue charging segments after an over the air (OTA) update. Confirm if the Charge Port Light toggle button is not present in the center display screen by selecting Vehicle Icon> Controls> Access> Charge Port Light toggle button, as this button has been removed after OTA update. Replacing the charge port and/or the battery charger control module (BCCM) is not recommended. This condition does not affect charge behavior and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in September 2023. Monitor OASIS for additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E vehicles may experience minor damage to the high voltage battery (HVB) tray as a result of coming contact with road debris and/or other outside influences. Workshop Manual (WSM), Section 414-03A has been updated to include new topics for inspection, repair and replacement of the HVB tray. These new topics should be used to help determine severity of damage and an appropriate repair direction for the HVB tray. If inspection per the WSM determines that the HVB tray requires replacement, the HVB battery trays for standard and extended range have been released for service as a lower cost repair option. Standard range HVB tray - LJ9Z-10732-E. Extended range HVB tray - LJ9Z-10732-D. When an HVB tray is replaced, a new high voltage battery serial number label must be obtained as directed in the WSM and installed in the location indicated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E vehicles may exhibit various driver assistance system warning messages or inoperative features and/or Diagnostic Trouble Code (DTC) U3000:49 stored in the Image Processing Module A (IPMA) that will not clear and not be stored in the vehicle's history. DTC C1001:31 and/or U3000:89 may be stored in the IPMA, but may have recently been cleared and stored in the vehicle's history. This may be due to a connection issue between the IPMA Camera and the IPMA. To correct the condition, perform the following service procedure to repair the connection and reset the IPMA.
Source components: EQUIPMENT · LANE DEPARTURE: LANE KEEP: STEERING ASSIST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150/Mustang Mach-E/Edge vehicles may exhibit a concern of Android Auto unable to wirelessly connect and/or Android phones rebooting when connected to the vehicle via USB. This is due to a concern with the Google application on the customers device. Google has released a fix for these concerns. For Android phones not connecting wirelessly, request that the customer update their Android Auto version to 6.1 or later. For customers who's Android phone reboots when connected via USB, request that the customer update their Chrome application to 88.0.4324.181 or later. The customers service provider should be able to assist customers having difficulty updating their device. This is not a warrantable repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E vehicles may experience loss of phone as a key after an over the air (OTA) update. There may also be diagnostic trouble code (DTC) U0214 stored various modules for loss of communication with the remote function actuator (RFA) module. This may be due to software in the RFA module causing it be locked/stuck in programming mode. To restore phone as a key functionality for the customer and RFA communication, remove RFA fuse (F18/19) located in the body control module (BCM) for one minute and plug it back in. Reprogram the RFA module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14G617 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E vehicles built on or before 16-Feb-2023 may exhibit a false alarm activation and/or warning message in the FordPass application when the doors are locked. This may be due to the software in the door latch control module E (DCME), door latch control module F (DCMF), door latch control module G (DCMG) and/or door latch control module H (DCMH). To correct the condition, download and run the door control module software update application for each module one at a time using the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 58219A65 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021-2022 Model Year Mustang Mach-E Vehicles Replace the Electronic Parking Brake Harness Connector In some of the affected vehicles, the Electronic Park Brake (EPB) may not function due to damaged or broken wiring. Customers may experience an audible chime, a wrench light, and a message on the Instrument Panel Cluster (IPC) specifying there is a Parking brake failure, service immediately. Some customers may be unable to disengage the park brake resulting in brake drag while driving accompanied by a constant minder and chime. The vehicle design will allow the affected vehicles to remain stationary on a grade even with a non-functioning EPB.
Source components: ELECTRICAL SYSTEM · PARKING BRAKE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150/Mustang Mach-E and 2023 Expedition/Navigator vehicles equipped with BlueCruise/ActiveGlide may experience loss of BlueCruise/ActiveGlide hands-free driving mode availability and/or BlueCruise/ActiveGlide inoperative and/or diagnostic trouble code (DTC) U2400:00 in the gateway module (GWM) and advanced driver assistance system (ADAS) modules with no other DTCs present. This may be due to an expired BlueCruise/ActiveGlide map file in the GWM and/or the customer's BlueCruise/ActiveGlide map subscription being expired. To correct the condition, follow the Service Procedure to update the GWM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E vehicles may experience an alarm activation even after the motion sensor function has been disabled through the pop-up menu at ignition off. If the customer wants to turn off the motion sensors for a key cycle, they can go to the center display screen: Vehicle > Settings > Alarm System > Motion Sensors off. The motion sensors will be re-enabled on the next key cycle. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in June 2023. Monitor OASIS for additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update 4 P1: For 2021- 2023 Model Year Mach E vehicles is now available. Quality improvements include: - Improved heater performance and interior humidity compensation. - Enhanced Power Steering Control Module communication. (Removes erroneous popup message) - Improvements to Lane Keeping Feature - Improvements in Cyber Security for Driver Assist Tech.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Mustang Mach-E vehicles may exhibit a Driver ID message on the center display screen when vehicle is turned on after an over-the-air update performed on or after 07-Dec-2022. The Driver ID message may also be accompanied by a connectivity loss including FordPass app displaying stale data or dates, unable to send cellular based remote commands through FordPass, and/or connectivity menu on SYNC not accessible. This may be due to the software in the gateway module (GWM). To correct the condition, follow the Service Procedure to reprogram the GWM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Ford and Lincoln vehicles may exhibit a condition where the high voltage battery stops charging when connected to level 1 or level 2 chargers with an illuminated malfunction indicator lamp (MIL) and diagnostic trouble code (DTC) P2C94 stored in the secondary on-board diagnostic control module A (SOBDM). To restore charging capability, disconnect the off-board charging station charge handle from the vehicle charge port and reconnect. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in June 2023. Replacement of the SOBDM will not resolve this condition. Monitor OASIS for additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E vehicles may exhibit a lack/loss of heat and/or windshield interior fogging while driving during freezing temperatures. This may be due to the heating ventilation and air conditioning (HVAC) control module software. To correct the condition, follow the Service Procedure to update the HVAC control module software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021 Model Year Mach-E Additional Remote Control and Key Blank Customer feedback indicates that PaaK is not working as planned and a second remote control is desired. A second remote control and a key blank will be rovided for all affected vehicles. Owner Notification Mailing Schedule: Owner letters are expected to be mailed the week of March 6, 2023.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2355 to update the vehicle model years affected. Some 2021-2023 Mustang Mach-E, 2022-2023 e-Transit and F-150 Lightning vehicles may experience inoperative level 3 charging with an illuminated Charger Service Required indicator in the instrument panel cluster (IPC) and diagnostic trouble codes (DTCs) P0D93:00, P0D94:00, P0D98:00, P0D9E:00 and/or P0DA0:00 in the secondary on-board diagnostic module (SOBDM). If the charging cord is removed from the charge port without the lock/release button fully pressed, this can damage the charge port locking pin actuator and disable level 3 charging for the next charging session. To correct the condition, follow the Service Procedure to replace only the charge port lock actuator.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021 Model Year Mach-E Additional Remote Control and Key Blank REASON FOR THIS SUPPLEMENT Owner Notification Mailing Schedule: Owner letters are expected to be mailed the week of March 6, 2023. Owner Refunds: Refund expiration date extended to August 5, 2023. Pickup and Delivery: Updates to Pickup and Delivery details. Claims Preparation and Submission: Updated claiming for pickup and delivery
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 F-150 built on or before 19-May-2022, Mustang Mach-E built on or before 04-May-2022 and 2022 Expedition/Navigator vehicles built on or before 13-May-2022 may exhibit various driver assistance system warning messages or inoperative features and/or diagnostic trouble codes (DTC) U3000:49, U3000:89, U2107:68, C1001:54 and/or C1001:78. This may be due to software in the IPMA. To correct the condition, follow the Service Procedure to reprogram the IPMA to the latest level.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E vehicles may experience minor damage to the high voltage battery (HVB) tray as a result of coming contact with road debris and/or other outside influences. Workshop Manual (WSM), Section 414-03A has been updated to include new topics for inspection, repair and replacement of the HVB tray. These new topics should be used to help determine severity of damage and an appropriate repair direction for the HVB tray. If inspection per the WSM determines that the HVB tray requires replacement, the HVB battery trays for standard and extended range have been released for service as a lower cost repair option. Standard range HVB tray - LJ9Z-10732-E. Extended range HVB tray - LJ9Z-10732-D.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Priority Update 23-PU0105-DC-CHG2 for 2021- 2023 Mach E vehicles is now available. Quality improvements include: - Improvement to DC Fast Charging functionality.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mustang Mach-E vehicles may exhibit a false alarm activation and/or warning message in the FordPass application when the doors are locked. This may be due to the software in the door latch control module E (DCME), door latch control module F (DCMF), door latch control module G (DCMG) and/or door latch control module H (DCMH). To correct the condition, download and run the door control module software update application for each module one at a time using the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 58219A65 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2402 to update the vehicle model years affected. Some 2021-2022 Mustang Mach-E base model (non-GT) built on or before 25-Jul-2022, 2022-2023 e-Transit vehicles built on or before 17-Sep-2022 may experience an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P1A3C, U3000:16, U3000:64, U3000:04 and/or U3000:45 in the off-board charging controller (OBCC) module and the high voltage (HV) battery will not charge using a level 3 direct current (DC) fast charging station/electrical vehicle supply equipment (EVSE). This may be due to OBCC software. To correct the condition, follow the Service Procedure to reprogram the OBCC.
Source components: ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION MOTOR:CONTROLLER:SOFTWARE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2105 to update the vehicles affected, issue, action, and service procedure. Some 2021-2022 F-150/Mach-E and 2022 Expedition/Navigator vehicles equipped with BlueCruise/ActiveGlide may experience loss of BlueCruise/ActiveGlide hands-free driving mode availability. This may be due to an expired BlueCruise/ActiveGlide map file in the gateway module (GWM). To correct the condition, follow the Service Procedure to update the GWM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E built on or before 17-Sep-2022, 2022 e-Transit vehicles may exhibit an illuminated red triangle indicator lamp with diagnostic trouble code (DTC) P27B4 stored in the secondary on-board diagnostic control module C (SOBDMC) or the charge status indicator (CSI) is blinking red with DTC P0A7F stored in the battery energy control module (BECM) and/or P0CF7 stored in the secondary on-board diagnostic control module A (SOBDM). This may be due to an unsecured plug-in electric vehicle supply equipment (EVSE). To correct the condition, follow the Service Procedure to reprogram the SOBDM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E vehicles built on or before 14-Sep-2022 may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P07E4:00 stored in the secondary on-board diagnostic control module C (SOBDMC) and/or unable to engage park (P). This may be due to the software in the SOBDMC. To correct this condition, follow the Service Procedure to reprogram the powertrain control module (PCM).
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ensure your vehicle is providing optimal output from its heating system, we have developed a software update to improve the heating capability, defrost and defog performance when exterior temperatures are at or below -15C/5F.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update 3 P2 for 2021-2021 Model Year Mustang Mach-E is now available. Quality Improvements Include: An improvement to how the Distance to Empty (DTE) is calculated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021 Model Year Mach-E, F-150, Bronco, Edge, Nautilus vehicles Electronic Control Module Recovery REASON FOR THIS SUPPLEMENT Program Terms: The program expiration date was incorrectly shown as October 31. 2022. The correct date is April 30, 2023. Affected Vehicles: The build dates were updated. Verbiage added to indicate the population will increase as more vehicles with modules needing recovery are identified. Service Action: Verbiage added to indicate the population will increase as more vehicles with modules needing recovery are identified. Owner Notification Mailing Schedule: Verbiage added on mailing owner letters to additional owners as they are identified. Owner Refund Expiration Date: The owner refund expiration date was incorrectly shown as May 27, 2022. The correct date is April 30, 2023.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Mustang Mach-E vehicles built on or before 07-Jul-2021 may experience Frunk System Fault Service Required message displayed in the IPC after performing body control module (BCM) update. This may be due to the software in the BCM. To correct the condition, follow the Service Procedure to reprogram the APIM, BCM and front trunk release module (FTRM). NOTE: The APIM software update that addresses the symptom listed in this article may have been delivered over-the-air (OTA) via Ford Power-Up software updates to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customers with 2021 F-150 and Mustang Mach-E vehicles equipped with Ford Co-Pilot360 Active 2.0 Prep Package seeking service to receive the BlueCruise hands-free driver assist Software in their vehicle. FSA 21G01 expired on 30-Sep-2022, however the bulletin and technical instructions are available on PTS to support technicians performing customer pay operations. Enter 21G01 in the PTS search engine on the upper right side of the webpage and select Technical Info to download the installation instructions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E built on or before 17-Jan-2022, 2022 Escape built on or before 03-Mar-2022, Bronco Sport built on or before 04-Mar-2022, 2022 Maverick built on or before 25-Jan-2022 and 2022 Transit built on or before 17-May-2022 may exhibit a powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0929:77 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct this condition, perform Pinpoint Test D. Refer to Workshop Manual (WSM), Section 307-05 > Diagnosis and Testing. If the GSM is not operating correctly, perform the replacement of the GSM. Do not perform a PMI after installing a new GSM assembly. The GSM is shipped with the latest software level. For claiming, use causal part 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2150 and SSM 50970 to update the Service Procedure. For some 2021 Mustang Mach-E, F-150, Edge, Nautilus and Bronco vehicles technicians may experience the inability to update the accessory protocol interface module (APIM), telematics control unit (TCU) or gateway module (GWM) using the Ford Diagnosis and Repair System (FDRS) and Universal Serial Bus (USB) drive. The PTS OTA Dashboard on vehicles with this condition may also display multiple APIM and/or TCU updates have failed, and/or a no OTA history message. In addition, on vehicles with this condition, the customer may have reported experiencing a Ford Power-Up software update failure message via the vehicle display and/or FordPass/LincolnWay. This may be due to an internal software error. To correct this condition, follow the Service Procedure to update and/or recover the APIM/TCU. Note: Only 10% of vehicles may require this procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E base model (non-GT) built on or before 25-Jul-2022, 2022 e-Transit vehicles built on or before 17-Sep-2022 may experience an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P1A3C, U3000:16, U3000:64, U3000:04 and/or U3000:45 in the off-board charging controller (OBCC) module and the high voltage (HV) battery will not charge using a level 3 direct current (DC) fast charging station/electrical vehicle supply equipment (EVSE). This may be due to OBCC software. To correct the condition, follow the Service Procedure to reprogram the OBCC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E vehicles may exhibit a concern where the vehicle is unable to be charged with the mobile charger. This may be due to a broken charge handle latch. To correct the condition, replace the mobile charger. For claiming, use causal part 10B706 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E/Escape plug-in hybrid electric vehicle (PHEV), 2020-2022 Aviator PHEV, and 2022 Transit battery electric vehicle (BEV) vehicles may experience an illuminated powertrain malfunction (Wrench) indicator and/or malfunction indicator lamp (MIL) with secondary on board diagnostic control module (SOBDM) diagnostic trouble code (DTC) U3000:49. This may be due to an internal SOBDM concern. To correct the concern, replace the SOBDM following Workshop Manual, Section 414-03B Removal and Installation, Secondary On-board Diagnostic Control Module. For claiming use base part # 10B689 and the applicable labor operations of Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021 Model Year Mach-E Additional Remote Control and Key Blank REASON FOR THIS SUPPLEMENT Affected Vehicle Build Dates: The build date range for the affected vehicles was incorrectly listed as through June 7, 2021. The correct build date range is July 7, 2021. All affected vehicles were correctly identified in OASIS and FSA VIN lists. Parts Requirements/Ordering Information: Updates to remote control and key blank ordering/claiming information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Program 22B28 for 2021-2022 Model Year Mustang Mach-E vehicles is now available. Quality Improvements Include: Improved HVAC system heat capability when exterior temps are at or below -15 C/5 F
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2022 Model Year Expedition/Navigator, 2021-2022 Model Year F-150 and Mach-E Vehicles Equipped with Ford/Lincoln Co-Pilot and BlueCruise/ActiveGlideBlueCruise/ActiveGlide Maps Expiration REASON FOR THIS SUPPLEMENT The technical instructions have been updated with additional details and screen shots to assist in successfully updating the gateway module (GWM) and BlueCruise/ActiveGlide Maps. Additional population has been added to the affected vehicles with updated build dates. Added requirement to verify through PTS that the Field Service Action (FSA) is still open (OASIS) and the vehicle has not already received the OTA update
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E non-GT, 2022 e-Transit vehicles may experience concerns with DC fast charge dropouts at certain EVgo Fat Boy charging stations with a red flashing charge status indicator (CSI), a charge failure notification on the touchscreen panel and the FordPass app. To correct the condition, update the off-board charger controller (OBCC) module to the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 14G672 and actual time for the labor operation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E, 2022 F-150 Lightning/e-Transit may experience diagnostic trouble codes (DTCs) P1A10 in the secondary on-board diagnostic module C (SOBDMC) and U3012 in the battery energy control module (BECM) after a low voltage service disconnect (LVSD). If both DTCs have set simultaneously, this may be due to the LVSD not being fully seated. Inspect the LVSD C1001 for being fully seated which is located on the left side of the under hood compartment. Refer to Workshop Manual (WSM), Section 414-03A High Voltage Battery > Mounting and Cables > General Procedures.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mach-E, 2022 Transit BEV and F-150 Lightning vehicles may experience inoperative level 3 charging with an illuminated Charger Service Required indicator in the instrument panel cluster (IPC) and diagnostic trouble codes (DTCs) P0D93:00, P0D94:00, P0D98:00, P0D9E:00 and/or P0DA0:00 in the secondary on-board diagnostic module (SOBDM). If the charging cord is removed from the charge port without the lock/release button fully depressed, this can damage the charge port locking pin actuator and disable level 3 charging for the next charging session. To correct the condition, follow the Service Procedure to replace only the charge port lock actuator.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E vehicles built on 01-Aug-2021 and through 18-Jan-2022, 2022 Maverick vehicles built on 13-Sep-2021 and through 18-Jan-2022, 2022 Escape vehicles built on 24-Sep-2021 and through 18-Jan-2022, 2022 Bronco Sport vehicles built on 08-Nov-2021 and through 18-Jan-2022 may exhibit a shift knob can be rotated without stepping on the brake pedal, although the transmission remains in park (P). This condition may be intermittent, more noticeable in warmer temperatures. DTC P0929 may also be set in the gear shift module (GSM). This may be due to a GSM concern. To correct the condition, follow the Service Procedure to update the GSM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Priority Update 22-PU0603-DC-CHG for 2021-2022 Model Year Mustang Mach-E vehicles is now available. Quality Improvements Include: Addresses failed DC fast charging attempts and allows use Plug & Charge feature.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E, 2022 Escape/Bronco Sport/Maverick/Transit vehicles may exhibit a powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0929:77 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct this condition, reprogram the GSM module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Priority Update 22-PU0727-VI-FX for 2021-2022 Model Year Mustang Mach-E vehicles is now available. Quality Improvements Include: Prevent "failure to de-inhibit" condition on future PSCM OTA updates.