2017 Ford F-350 SD Manufacturer communications & TSBs.Page 3
Original record summaries, dates and identifiers for this model-year. Records 201–300 of 325, ordered newest first. Dated records on this page: Jan 24, 2017–Jan 18, 2019.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jan 18, 2019Service Bulletin/Repair Instructions
TSB 19-2007
NHTSA communication ID: 10153920
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 F-150 vehicles built at Kansas City Assembly Plant on or after 4-Apr-2018 and Dearborn Truck Plant on or after 13-Apr-2018 and some F-Super Duty vehicles built at Kentucky Truck Plant on or after 22-Apr-2018 and Ohio Assembly Plant on or after 18-Apr-2018 may exhibit doors that are difficult to unlatch or latch in temperatures at or below freezing. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-Super Duty vehicles equipped with a 6.7L engine built on or before 18-Apr-2018 may exhibit an illuminated malfunction indicator lamp (MIL) with DTC P244A and/or P2452. This may be due to a malfunction of the diesel particulate filter (DPF) differential pressure sensor. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty and 2016-2019 F650-750 with 6.7L diesel engines, 2015-2019 Transit with 3.2L diesel engines and 2018-2019 F-150 with 3.0L diesel engines may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P206C in the powertrain control module (PCM). Review of repair data supports that P206C is often the result of incorrect diesel exhaust fluid (DEF) concentration. Per Powertrain Control/Emissions Diagnosis (PC/ED) Pinpoint Test (PPT) RJ, a DEF concentration reading below 28% will set P206C and cause vehicle derate. If low concentration is suspected, drain fluid and replace with known good DEF before replacing any parts. Low concentration of DEF is not a warrantable condition.
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150, 2017-2019 F-Super Duty, 2018-2019 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit a binding/sticking, glass stuck open or closed, noisy operation including chatter, rattling, or grinding. This may be due to the glass brackets cracking and/or breaking apart. The glass panel brackets are serviceable separately from the frame assembly and require the roof opening panel glass to be moved to the vent position. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-Super Duty vehicles equipped with a 6.7L diesel engine built on or before 09-Jul-2018 may exhibit an illuminated MIL with DTCs P24AE, P24AF, P24B1, P24B3, P24C6, P24C7, and/or P24DA in the powertrain control module (PCM). This may be due to a concern with the diesel particulate matter sensor. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles may exhibit a headliner edge that shows around the overhead console. Using a trim stick or other suitable tool, the headliner should be tucked back in without replacement of the entire headliner.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty, 2016-2017 Expedition/Navigator and 2016-2018 Focus/Fiesta vehicles may exhibit a concern where the radio reverts to an AM or FM station after shutting the vehicle off, leaving it off for at least 20 minutes, and then starting it back up. Do not perform any repairs for this concern. If a vehicle exhibits this concern, please use the Report a Vehicle Concern link at the bottom of the OASIS tab and submit a report. Engineering is investigating. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles may exhibit a whistle type noise from under the hood while under load and/or while driving. Make sure there is a proper connection between the air cleaner lower intake duct, located under the battery tray, and the air cleaner. Refer to Workshop Manual (WSM), Section 303-12C and WSM, Section 414-01 for further information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 F-Super Duty vehicles equipped with a 6.7L engine built on or before 1-Jun-2017 may exhibit a leak from the primary coolant pump. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated MIL with only DTC P2074 stored in the powertrain control module (PCM). This may be due to a dirty air filter, replace the filter if necessary. Do not replace the PCM or mass air flow (MAF) sensor for this concern. Instead perform a MAF parameter reset under: Toolbox > Powertrain > Service Functions > Reset/Clear Specified Function > Reset/Clear Functions > MAF Sensor. Engineering is investigating. Monitor OASIS for updates.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This SKU is a front upper ball joint. The Customer communication requested return of unsold inventory to inspect for ball studs with excessive rotational friction in the ball joint assembly. Excessive friction in the ball joint assembly may cause a perceptible increase in steering effort.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles and 2018 Expedition/Navigator vehicles may exhibit a concern where the radio reverts to an AM or FM station after shutting the vehicle off, leaving it off for at least 20 minutes, and then starting it back up. Do not perform any repairs for this concern. If a vehicle exhibits this concern, please use the Report a Vehicle Concern link at the bottom of the OASIS tab and submit a report. Engineering is investigating. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty/2018 F-150 vehicles equipped with the 6.7L or 3.0L engines may exhibit an illuminated malfunction indicator lamp (MIL) with DTC P208E in the powertrain control module (PCM). When performing pinpoint test RK, the results of the selective catalyst reductant (SCR) dosing measurement test (RK7) may be zero or below the specified 40-50mL requirement due to urea crystals plugging the DEF injector nozzle. If the measurement is below this specified amount, perform pinpoint test step RK7 two additional times. If the specified amount is met, reinstall the reductant injector. If after three attempts the dosing measurement remains below the specified amount, the DEF injector should be replaced. The DEF pump should not be replaced for DTC P208E. Engineering is investigating. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated MIL with only DTC P2074 stored in the powertrain control module (PCM). Do not replace the PCM or mass air flow (MAF) sensor for this concern. Instead perform a MAF parameter reset under: Toolbox - Powertrain - Service Functions - Reset/Clear Specified Function - Reset/Clear Functions - MAF Sensor. Engineering is investigating. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-250/F-350 4WD vehicles built on or before 31-Jul-2018 may exhibit a sustained steering wheel oscillation after hitting rough pavement or an expansion joint above 45 mph (72 Km/h). Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-Super Duty vehicles equipped with a 6.7L engine built on or before 8-Jul-2018 may exhibit a lack of heat coming from the driver side vents when operating the vehicle in ambient temperatures below -20Å?C (4Å?F). This condition may be due to deposits from the engine coolant trapped in the heater core. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 F-Super Duty vehicles equipped with a 6.7L engine built on or before 1-Jun-2017 may exhibit a leak from the coolant pump. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When performing diagnostics for DTCs P2201, P2452, P2459, P246C and/or P2463, a manual regeneration and diesel particulate filter (DPF) parameter reset using the appropriate scan tool may need to be performed. To perform the manual regeneration, go to the Toolbox tab > Powertrain > Service Functions > Diesel Particulate Regeneration System > DPF Manual Regeneration. The scan tool may indicate that a regeneration of the DPF is not recommended at this time, selecting YES on this screen will allow the regeneration process to complete. To perform the DPF parameter reset, go to the Toolbox tab > Powertrain > Service Functions > Diesel Particulate Regeneration System > DPF Parameter Reset.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 F-Super Duty vehicles equipped with a 6.7L engine built on or before 1-Jun-2017 may exhibit a leak from the coolant pump. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-Super Duty vehicles may exhibit a headliner edge that shows around the overhead console. Using a trim stick or other suitable tool, the headliner should be tucked back in without replacement of the entire headliner.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-Super Duty vehicles equipped with a 6.7L diesel engine built on or before 15-Mar-2018 may exhibit an illuminated WIF indicator with DTCs P1140, P2266 and/or P2269 stored in the powertrain control module (PCM). This may be due to water intrusion into connector C3080 at the WIF sensor. Follow the Service Procedure steps to correct the condition.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-Super Duty pickups may exhibit an instrument panel cluster (IPC) turn signal indicator that flashes fast with no inoperative turn signal lamps after the pickup box has been removed by the upfitter. This may be due to the body control module (BCM) not recognizing the modified lower current turn signal lighting that was installed. To correct this concern, use Integrated Diagnostic System (IDS) service tool version 104.04 or later to configure turn lamp outage settings as required. Under toolbox > module programming > programmable parameters > exterior lighting, select rear bulb turn outage and outage ABM and change the setting on each parameter from outage to no outage. Changes to lamp outage settings on pickups as a result of upfitter modifications are non-warrantable. Upfitters are responsible for FMVSS 108 compliance.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EXTERIOR LIGHTING:TURN SIGNAL · EXTERIOR LIGHTING:TURN SIGNAL:FLASHER UNIT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-Super Duty vehicles equipped with a 6.7L diesel engine built on or before 6-Dec-2017 may exhibit an exhaust odor in the vehicle cabin. This may be due to a leak at the turbocharger inlet clamps. Performing a pressurized smoke test on the exhaust system will aid in locating the source of a leak. While performing the smoke test, the use of a small mirror can help identify leaks underneath the clamps. Refer to the Powertrain Control/Emissions Diagnosis (PC/ED) Manual Pinpoint Test KA, Step KA3. Note that the turbo charger is not a contributing factor in the exhaust leak issue.
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · EQUIPMENT · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150 and 2017-2018 F-Super Duty vehicles may exhibit a lack of cooling from the heating ventilation air conditioning (HVAC) system due to a low refrigerant charge. Using an ultraviolet (UV) leak detection light, inspect the condenser near the receiver/dryer cap for the presence of dye. If dye is present, replace the condenser. For claiming, use causal part 19712 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 Expedition/Navigator vehicles built on or before 24-Feb-2018, 2017-2018 F-Super Duty built on or before 26-Feb-2018 and Transit vehicles built on or before 26-Feb-2018 and 2015-2018 F-150 vehicles built on or before 3-Mar-2018 may exhibit a trailer connected and/or disconnected message in the IPC without a trailer connected. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty vehicles equipped with a 6.7L diesel engine built on or before 24-Oct-2017 may exhibit an inoperative block heater. This can also result in tripping an electrical breaker or a ground fault circuit interrupter (GFCI) outlet. This may be due to water intrusion into the block heater power cord inline connector. Follow the Service Procedure steps to correct the condition.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:ENGINE:DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-Super Duty vehicles may exhibit incorrect air temperature from the heating ventilation and air conditioning (HVAC) outlets with DTC B1081:07 in the front controls interface module (FCIM). This may be due to binding of the blend door in the HVAC housing or binding between the temperature door actuator and the cam to the temperature door. Replacement of temperature door actuator and cam driver is recommended if the blend door is not binding. Note that removal of the cam driver follower from the blend door shaft can result in damage.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-Super Duty vehicles equipped with a 6.2L or 6.8L gas engine may exhibit multiple warning indicators in the instrument panel cluster and/or inoperative radio during snow plow use. Battery state of charge is important to verify prior to any repairs. 12.72v to 12.8v is a fully charged battery. To assist with the investigation use the Report a Vehicle Concern link at the bottom of the OASIS report and include the following information: What brand of plow the vehicle is equipped with, If it's been equipped by the plow manufacturer's specifications, If other equipment is up-fitted on the vehicle, ambient temperature when the concern occurs, Engine RPM and MPH/KPH, and battery state of charge. Note the concern should be duplicated similar to customer use and ambient temperature.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty vehicles equipped with a 6.7L diesel engine may exhibit an exhaust odor in the vehicle cabin. This may be due to a leak at the turbocharger inlet clamps. Performing a pressurized smoke test on the exhaust system will aid in locating the source of a leak. While performing the smoke test, the use of a small mirror can help identify leaks underneath the clamps. Refer to the Powertrain Control/Emissions Diagnosis (PC/ED) Manual Pinpoint Test KA, Step KA3. Note that the turbo charger is not a contributing factor in the exhaust leak issue.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-Super Duty vehicles equipped with Tire Pressure Monitoring Systems (TPMS) may exhibit a leak at the tire valve stem. When making repairs to the tire valve stem, there is a service kit available that does not include the Tire Pressure Monitoring System (TPMS) sensor. When replacing the tire valve stem follow the procedure in Workshop Manual (WSM), Section 204-04A. For claiming, use causal part 1700 and applicable labor operations in Section 01 of the service labor time standards (SLTS) manual.
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated MIL with diagnostic trouble code (DTC) U029D and/or P2209 in the powertrain control module (PCM). This may be due to water intrusion. Follow the Service Procedure steps to correct the condition.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 and connected to an iPhone recently upgraded to iOS 11.2.5 may exhibit functional concerns where USB audio playback and App Link will not operate. This may also include, under certain conditions, no Bluetooth streaming. Apple has released iOS 11.2.6 to address this concern. Advise the customer to update the device to iOS 11.2.6 and re-evaluate before performing any diagnosis or repairs for this condition. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Continental/F-Super Duty vehicles may exhibit a DTC B13BD in the steering effort control module (SECM). This DTC sets when the Ford Integrated Diagnostic System (IDS) self test is run and is a result of a software issue between the SECM and the IDS. After the IDS self test is run DTC B13BD sets and the heated steering wheel is disabled. To eliminate the DTC and return the heated steering wheel functionality, perform the IDS SASM module reset routine. The IDS reset routine is available under Toolbox > Chassis > Steering > Adaptive Front Steering > SASM Module Reset. For claiming, use causal part 3600 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-Super Duty vehicles equipped with an audio unit antenna may be damaged due to over travel of the hood. Removal of hood struts will allow the hood to over travel and contact the antenna base resulting in damage. Support of the hood is recommended prior to hood strut removal. Refer to Workshop Manual (WSM), Section 501-02.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty, 2016-2017 F650-750 equipped with 6.7L diesel engines and 2015-2017 Transit equipped with 3.2L diesel engines may exhibit a MIL on with diagnostic trouble code (DTC) P206C stored in powertrain control module(PCM). This may be due to incorrect diesel exhaust fluid (DEF) concentration. Prior to performing Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test RJ, ensure DEF concentration is checked using Central Tools Refractometer tool number CEN3R201 and if DEF contamination is suspected use the Rotunda Hydrocarbon Test Kit tool number 328-480508.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2018 F-Super Duty 6.7L diesel equipped vehicles may exhibit a ticking noise at idle after an engine oil change. It is often referred to as Typewriter Noise because of its similarity to the sound of a mechanical typewriter. When engine temperatures reach 150 Å?F (65 Å?C) or higher, (from engine idle up to approximately 1700 RPM's), this noise can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. Typewriter Noise is not detrimental to engine function or durability and has no short or long term effects on the engine. Do not attempt repairs to eliminate this noise. This noise is characteristic of the 6.7L diesel engine and will typically cease or diminish significantly within the oil change maintenance interval.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2018 F-Super Duty 6.7L diesel equipped vehicles may exhibit a ticking noise at idle after an engine oil change. It is often referred to as Typewriter Noise because of its similarity to the sound of a mechanical typewriter. When engine temperatures reach 150 Å?F (65 Å?C) or higher, (from engine idle up to approximately 1700 RPM's), this noise can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. Typewriter Noise is not detrimental to engine function or durability and has no short or long term effects on the engine. Do not attempt repairs to eliminate this noise. This noise is characteristic of the 6.7L diesel engine and will typically cease or diminish significantly within the oil change maintenance interval.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty vehicles equipped with a 6.7L diesel engine may exhibit a fuel knock type noise at idle, illuminated MIL with one or more of the following DTCs stored in powertrain control module (PCM) memory: P0263, P0266, P0269, P0272, P0275, P0278, P0281, P0284, P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F. This may be due to incorrect learning of the injector timing within the PCM. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, 2017-2018 F-Super Duty, 2018 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit binding while opening or closing of the movable glass panel. The roof opening panel glass brackets are available for service. Both brackets must be replaced, FL3Z-1651070-A right side and FL3Z-1651071-A left side. Refer to Workshop Manual (WSM), Section 501-17 for removal and installation procedure. For claiming, use causal part 51070 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty vehicles equipped with a 6.7L engine and built on or before 7-Nov-2017 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P20EE, P2459, P2201, P246C and/or P2463. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty vehicles equipped with a 6.7L engine and built on or before 7-Nov-2017 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P20EE, P2459, P2201, P246C and/or P2463. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update APIM software. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available, refer to WSM Section 415-00 and update the APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · EQUIPMENT · LANE DEPARTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, 2017-2018 F-Super Duty, 2018 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit binding while opening or closing of the movable glass panel. The roof opening panel glass brackets are available for service. Both brackets must be replaced, FL3Z-1651070-A right side and FL3Z-1651071-A left side. Refer to Workshop Manual (WSM), Section 501-17 for removal and installation procedure. For claiming, use causal part 1651070 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty vehicles with 6.7L diesel engines may exhibit a fuel knock type noise at idle with various cylinder contribution/balance DTCs and/or Fuel Injector Offset Learn DTCs. To resolve this issue please use the following procedure: 1) Make sure ECT1 and EOT are above 176Å?F (80Å?C). 2) Using the IDS or FJDS, run the Manual Injector Balance Test/Enhanced Power Balance Test under Toolbox, Powertrain, Power Balance. If the noise is gone after running the Enhanced Power Balance test, then clear the High Pressure Side Minimum Fuel Mass Adaptation tables for all cylinders, and the Crankshaft Position Sensor under Toolbox, Powertrain, Service Functions, Reset, Clear Specified Function. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.
Source components: FUEL SYSTEM, DIESEL · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty pickup vehicles built on or before 7-Jun-2017 may exhibit various intermittent electrical concerns due to water intrusion into the 14405 wire harness. Symptoms may include, but are not limited to uncommanded tailgate opening when equipped with power tailgate, loss of communication on the medium speed controller area network (MS-CAN) and/or inoperative rear parking aid camera on vehicles without 360 degree view camera system. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty vehicles built on or before 28-Aug-2017, may exhibit an intermittent loss of throttle pedal response, illuminated wrench, hill descent, airbag, anti-lock brake system (ABS) and/or advanced trac warning indicators and/or P2122, P2123, P2124, P2125, P2127, P2128, and/or P2138 DTCs. This may be caused by the Accelerator Pedal Position (APP) sensor 14A005 harness being improperly routed behind the brake booster to brake pedal bracket. If the harness is improperly routed, loosen the bracket to free the harness, refer to Workshop Manual (WSM), section 206-06 and inspect for any damaged circuits. If the harness is properly routed, proceed with normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty vehicle built on or before 24-Aug-2017 may exhibit inoperative A/C operation. This may be due to broken or damaged circuits CH401 (VT-WH) and/or GD131 (BK-GY). Inspect for harness damage between connector C100 at the A/C Compressor and inline connector C1046. This damage may take place during the assembly process. If there is no damage present to either circuit please continue with normal Workshop Manual (WSM) diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. To recover the screen, perform any one of the following actions: touch the SYNC screen anywhere outside the vehicle image pop-up box, safely shift the vehicle into and out of reverse, or perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). If this does not resolve the concern, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford or Lincoln vehicles equipped with SYNC 3 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
During PDI, 2017 F-Super Duty vehicles equipped with tire pressure monitor system (TPMS) will exhibit an illuminated low tire pressure warning light and low tire pressure readout in the message center (if equipped) from the factory. Using a calibrated digital tire pressure gauge, adjust the tire pressure to specification and do not refer to the pressure displayed in the message center. During the PDI, the vehicle must be driven over 20 mph (32 kph) for at least 2 minutes to update the pressure displayed and turn off the tire pressure warning. It is not necessary to train or activate sensors with the service tool during PDI. If the TPMS low tire pressure warning is still present or message center pressure readout is inaccurate after completing the PDI road test, refer to the online Workshop Manual, Section 204-04B for normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty vehicles equipped with a 6.7L engine and built on or before 12-May-2017 may exhibit an illuminated MIL with DTC P2002 only. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty vehicles equipped with a 6.7L engine and built on or before 12-May-2017 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P20EE, P2459, P2201, P246C and/or P2463. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty vehicles equipped with a 6.7L engine built on or before 12-May-2017 may exhibit an illuminated MIL with DTC P244A. This may be due to a malfunction of the diesel particulate filter (DPF) differential pressure sensor. Follow the TSB Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 F-Super Duty vehicles equipped with a 6.7 engine and built on or before 12-May-2017 may exhibit any or all of the following concerns at times of high electrical system draw such as snow plow operation, instrument cluster backlighting inoperative, erratic climate control blower motor operation, red brake warning indicator flickering and/or low battery temperature features turned off being displayed in the message center. Follow the TSB Service Procedure steps to correct the condition.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SERIES SUPER DUTY PICKUPS EQUIPPED WITH A REAR AUXILIARY POWER POINT AND BUILT ON OR BEFORE 20-FEB-2017 MAY REMAIN RUNNING AFTER THE IGNITION IS TURNED OFF. PRIOR TO PERFORMING ANY DIAGNOSTICS, INSPECT THE REAR AUXILIARY POWER POINT FOR ANY AFTERMARKET DEVICES THAT CAN SUPPLY VOLTAGE BACK INTO THE VEHICLE. ITEMS SUCH AS A BATTERY JUMP PACK CAN INDUCE VOLTAGE THAT WILL SIMULATE KEY ON STATUS AND PREVENT THE POWERTRAIN CONTROL MODULE (PCM) FROM SHUTTING OFF THE ENGINE. IF NO AFTERMARKET DEVICES CAN BE LOCATED, REFER TO WORKSHOP MANUAL (WSM), SECTION 211-05 FOR NORMAL DIAGNOSTICS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2017 F-SUPER DUTY VEHICLES BUILT ON OR BEFORE 22-FEB-2017 MAY HAVE TIMED 12 VOLT AUXILIARY POWER POINTS THAT DISABLE WHEN THE IGNITION IS TURNED OFF AND A DOOR IS OPENED. POWER POINTS ARE TIMED WITH THE EXCEPTION OF THE ONE LOCATED ON THE REAR OF THE CENTER CONSOLE, IF EQUIPPED. TIMED POWER POINTS SHOULD REMAIN ON FOR 30 MINUTES WHEN IN ACCESSORY MODE AND 75 MINUTES WHEN IGNITION IS TURNED OFF. TO CORRECT THIS CONDITION, REPROGRAM THE BODY CONTROL MODULE (BCM) TO THE LATEST CALIBRATION USING IDS RELEASE 104.04 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. FOR CLAIMING, USE CAUSAL PART 15604 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2016-2017 FORD OR LINCOLN VEHICLES EQUIPPED WITH SYNC 3 MAY EXHIBIT A BLANK SCREEN OR OTHER VARIOUS SYNC SYMPTOMS ONLY WHEN THE VEHICLE IS IN TRANSPORT MODE. THIS IS CONSIDERED NORMAL DUE TO THE POWER SAVING FEATURES ENABLED WHILE IN TRANSPORT MODE. IT IS BENEFICIAL FOR BATTERY LIFE TO KEEP THE VEHICLE IN TRANSPORT MODE UNTIL THE VEHICLE IS PREPPED FOR SALE. TO PREVENT A SYNC SYSTEM LOCKUP DURING TRANSPORT MODE DEACTIVATION, FOLLOW THE WORKSHOP MANUAL (WSM) PROCEDURE EXACTLY ALLOWING TIME FOR THE SYNC SYSTEM TO COMPLETE ITS TASKS SUCH AS FULLY BOOTING UP OR POWERING DOWN AND SHUTTING OFF BEFORE MOVING TO THE NEXT STEP OF THE PROCEDURE. IF THE VEHICLE EXHIBITS A BLANK SCREEN OR SYNC SYMPTOMS AFTER TRANSPORT MODE DEACTIVATION, REFER TO WSM, SECTION 415-00 FOR NORMAL DIAGNOSIS. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SUPER DUTY VEHICLES EQUIPPED WITH A 6.7L ENGINE MAY EXHIBIT AN ILLUMINATED MIL WITH DTC P259F ONLY. IF FREEZE FRAME DATA INDICATES THE DTC OCCURRED WHEN ENGINE COOLANT TEMPERATURE (ECT) WAS BELOW 10 DEGREES C (50 DEGREES F) AND UNDER 3 MINUTES OF ENGINE RUN TIME, CLEAR THE DTC AND PERFORM A KEY ON ENGINE RUNNING (KOER) SELF TEST USING THE INTEGRATED DIAGNOSTIC SYSTEM (IDS) OR EQUIVALENT SCAN TOOL. IF NO TURBOCHARGER AND CHARGE AIR COOLER (CAC) SYSTEM DTCS RETURN DURING KOER SELF TEST, DO NOT ATTEMPT ANY REPAIRS AT THIS TIME AND RELEASE THE VEHICLE. ENGINEERING IS CURRENTLY INVESTIGATING THIS CONCERN, MONITOR OASIS FOR UPDATES REGARDING LATEST INFORMATION AND DIAGNOSTIC DIRECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THE 2017 POWERTRAIN CONTROL/EMISSIONS DIAGNOSIS (PC/ED) MANUAL HAS BEEN REVISED FOR DIAGNOSING ELECTRONIC THROTTLE BODY (ETB). FOR ALL ETB CONCERNS, THE APPROPRIATE DIAGNOSTIC MUST BE COMPLETED BEFORE THROTTLE BODY REPLACEMENT. IF A CONCERN IS INTERMITTENT AND NO DTCS ARE PRESENT, REFER TO HISTORICAL DTCS AND THE PC/ED, SECTION 3 NO DTCS PRESENT INDEX CHART FOR FURTHER INFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SUPER DUTY VEHICLES EQUIPPED WITH A 6.7L ENGINE AND BUILT ON OR BEFORE 07-FEB-17 MAY EXHIBIT A ILLUMINATED MALFUNCTION INDICATOR LAMP (MIL) ON WITH DTC P06A6, P0193, P02E9, P0335, P0532 AND/OR P2454. THIS MAY BE DUE TO A CONCERN WITH THE REFERENCE VOLTAGE OR SIGNAL RETURN CIRCUIT OF THE CRANKSHAFT POSITION SENSOR (CKP) WIRING. INSPECT CKP SENSOR HARNESS CIRCUITS APPROXIMATELY 381MM(15 INCHES) FROM THE CKP SENSOR CONNECTOR FOR DAMAGE OR EVIDENCE OF BEING PINCHED. IF A WIRING CONCERN IS FOUND, REPAIR AS DIRECTED PER WIRING DIAGRAM SECTION 5. USE CAUSAL PART 12B637 AND UTILIZE APPLICABLE LABOR OPERATIONS FROM SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SUPER DUTY VEHICLES EQUIPPED WITH ELECTRONIC SHIFT ON THE FLY (ESOF) FOUR WHEEL DRIVE MAY EXHIBIT A 4X4 INDICATOR ILLUMINATED WITH DTC P1839 IN THE TCCM. THIS MAY BE CAUSED BY A BACKED OUT OR LOOSE PIN FOR CIRCUIT CCF07 BN-GN AT C1010 WHICH IS LOCATED BY THE DRIVER SIDE FENDER. BEFORE ATTEMPTING DIAGNOSIS OR REPAIRS, INSPECT PIN 16 IN CONNECTOR C1010. IF NO CONCERN IS FOUND, REFER TO WORKSHOP MANUAL (WSM), SECTION 308-07 FOR NORMAL DIAGNOSTICS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SERIES SUPER DUTY PICKUPS EQUIPPED WITH A 6.7L ENGINE AND A REAR AUXILIARY POWER POINT MAY EXHIBIT A ILLUMINATED MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODES (DTCS) P1261, P1262, P1263, P1264, P1265, P1266, P1267 AND/OR P1268. IF FREEZE FRAME INDICATES DTCS SET BELOW 600 RPM AND THERE ARE NO DRIVABILITY SYMPTOMS, INSPECT THE CENTER CONSOLE REAR AUXILIARY POWER POINT FOR AFTERMARKET DEVICES. ITEMS SUCH AS A 12 VOLT REFRIGERATOR OR COOLER MAY INDUCE FEEDBACK VOLTAGE INTO THE VEHICLE THAT WILL CAUSE THE POWERTRAIN CONTROL MODULE (PCM) TO FALSELY SET INJECTOR CIRCUIT FAULT DTCS. IF NO AFTERMARKET DEVICES CAN BE LOCATED OR ARE BEING USED BY THE CUSTOMER IN THIS POWER POINT LOCATION, REFER TO THE POWERTRAIN CONTROL/EMISSIONS DIAGNOSIS (PC/ED) MANUAL FOR NORMAL DIAGNOSTICS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2009-2017 VEHICLES EQUIPPED WITH A 6R80, 6R100, 6R140 AUTOMATIC TRANSMISSION HAVE AN UPDATED MAIN CONTROL VALVE BODY OVERHAUL PROCEDURE. REFER TO WORKSHOP MANUAL (WSM), SECTION 307-01 FOR MAIN CONTROL VALVE BODY (7A100) OVERHAUL PROCEDURES. NOT ALL VALVE BODIES REQUIRE REPLACEMENT. INSPECT THE VALVE BODY BORES, SPRINGS AND VALVES AS DIRECTED DURING DIAGNOSIS AND REPAIR. REFER TO GENERAL SERVICE BULLETIN (GSB) G0000093 AUTOMATIC TRANSMISSION MAIN CONTROL INSPECTION FOR A VIDEO CLIP TO AID IN THE DIAGNOSIS OF THESE REPAIRS.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT AN ILLUMINATED MIL WITH DIAGNOSTIC TROUBLE CODES (DTCS) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 AND/OR P0025. THIS MAY BE DUE TO SMALL DEBRIS CAUSING THE VCT SOLENOID TO STICK. BEFORE ATTEMPTING ANY COMPONENT DIAGNOSIS OR REPLACEMENT OF THE VCT SOLENOID, REFER TO POWERTRAIN CONTROL AND EMISSIONS DIAGNOSIS (PC/ED) PINPOINT TEST HK11 TO CYCLE THE AFFECTED VCT SOLENOID 10 TIMES TO ATTEMPT TO CLEAR THE DEBRIS. FOR CLAIMING, USE CAUSAL PART 6M280 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 SUPER DUTY VEHICLES BUILT ON OR BEFORE 05-DEC-2016 MAY EXHIBIT INOPERATIVE INTERIOR LAMPS, MOONROOF AND/OR SUNSHADE WITH NO DIAGNOSTIC TROUBLE CODE (DTC) BEING PRESENT IN THE BODY CONTROL MODULE (BCM). THIS MAY BE CAUSED BY A PINCHED WIRE AT THE RIGHT AND/OR LEFT SIDE SUN VISOR MOUNT OF THE INTERIOR LAMP FEED BODY HARNESS. BEFORE ATTEMPTING DIAGNOSIS OR REPAIRS, INSPECT THE SUN VISOR MOUNT AREA FOR PINCHED WIRING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SUPER DUTY VEHICLES EQUIPPED WITH A 6.7L ENGINE MAY EXHIBIT AN ILLUMINATED MIL WITH DTC P244A. THIS MAY BE DUE TO A MALFUNCTION OF THE DIESEL PARTICULATE FILTER (DPF) DIFFERENTIAL PRESSURE SENSOR. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SUPER DUTY VEHICLES EQUIPPED WITH A 6.7L ENGINE AND BUILT ON OR BEFORE 19-DEC-2016 MAY EXHIBIT AN ILLUMINATED MIL WITH DIAGNOSTIC TROUBLE CODE (DTC) U029D AND/OR P2209 IN THE POWERTRAIN CONTROL MODULE (PCM) MEMORY. THIS MAY BE DUE TO WATER INTRUSION. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SUPER DUTY AND 2016-2017 F-650/F-750 VEHICLES EQUIPPED WITH A 6.7L ENGINE MAY EXHIBIT A DTC P0000. THIS DTC IS DUE TO A PROCESSING ERROR IN THE POWERTRAIN CONTROL MODULE (PCM) AS A RESULT OF ON DEMAND SELF TESTING WITH AN INTEGRATED DIAGNOSTIC SYSTEM (IDS). P0000 IS AN INVALID DTC THAT WILL NOT ILLUMINATE THE MIL AND SHOULD BE DISREGARDED.
Source components: ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SUPER DUTY, 2016-2017 F650/750 VEHICLES BUILT ON OR BEFORE 20-DEC-2016 AND EQUIPPED WITH A 6.7L ENGINE MAY EXHIBIT AN ILLUMINATED MIL WITH DIAGNOSTIC TROUBLE CODE (DTC) P20E8 IN THE POWERTRAIN CONTROL MODULE (PCM) MEMORY. THIS MAY BE DUE TO AIR TRAPPED IN THE REDUCTANT LINES CAUSING THE REDUCTANT PUMP AND HEATER ASSEMBLY TO NOT BUILD SUFFICIENT SYSTEM PRESSURE OR LOOSE REDUCTANT LINE CONNECTIONS. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SUPER DUTY VEHICLES EQUIPPED WITH A 6.2L GASOLINE ENGINE MAY EXHIBIT ANY OR ALL OF THE FOLLOWING CONCERNS AT TIMES OF HIGH ELECTRICAL SYSTEM DRAW SUCH AS SNOW PLOW OPERATION, INSTRUMENT CLUSTER BACKLIGHTING INOPERATIVE, ERRATIC CLIMATE CONTROL BLOWER MOTOR OPERATION, THE RED BRAKE WARNING INDICATOR FLICKERING, AND/OR LOW BATTERY - FEATURES TEMP TURNED OFF MESSAGE IN THE MESSAGE CENTER. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2011-2017 F-SUPER DUTY 6.7L DIESEL EQUIPPED VEHICLES MAY EXHIBIT A TICKING NOISE AT IDLE AFTER AN ENGINE OIL CHANGE. IT IS OFTEN REFERRED TO AS TYPEWRITER NOISE BECAUSE OF ITS SIMILARITY TO THE SOUND OF A MECHANICAL TYPEWRITER. WHEN ENGINE TEMPERATURES REACH 150 ÅF (65 ÅC) OR HIGHER, (FROM ENGINE IDLE UP TO APPROXIMATELY 1700 RPM'S), THIS NOISE CAN TYPICALLY BE HEARD AT THE FRONT WHEEL WELL AND IS OFTEN ISOLATED TO THE TRANSMISSION BELL HOUSING OR OIL PAN AREA. TYPEWRITER NOISE IS NOT DETRIMENTAL TO ENGINE FUNCTION OR DURABILITY AND HAS NO SHORT OR LONG TERM EFFECTS ON THE ENGINE. DO NOT ATTEMPT REPAIRS TO ELIMINATE THIS NOISE. THIS NOISE IS CHARACTERISTIC OF THE 6.7L DIESEL ENGINE AND WILL TYPICALLY CEASE OR DIMINISH SIGNIFICANTLY WITHIN THE OIL CHANGE MAINTENANCE INTERVAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SUPER DUTY VEHICLES EQUIPPED WITH A 6.7L ENGINE AND BUILT ON OR BEFORE 20-FEB-2017 MAY EXHIBIT AN ILLUMINATED MIL WITH DIAGNOSTIC TROUBLE CODES (DTCS) P20EE, P2002, P2201, P246C AND/OR P2463. REPROGRAM THE POWERTRAIN CONTROL MODULE (PCM) TO THE LATEST CALIBRATION USING IDS RELEASE 104.02 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SUPER DUTY VEHICLES WITH DUAL GENERATORS MAY EXHIBIT AN ILLUMINATED CHARGING LIGHT AND/OR CHARGING WARNING MESSAGE AFTER AN UPFITTER HAS REMOVED ONE OF THE GENERATORS. TO CORRECT THIS CONCERN, USE INTEGRATED DIAGNOSTIC SYSTEM (IDS) SERVICE TOOL VERSION 104.02 OR LATER TO CONFIGURE THE GENERATOR SETUP. THESE SETTINGS CAN BE FOUND UNDER TOOLBOX> MODULE PROGRAMMING >PROGRAMMABLE PARAMETERS> POWERTRAIN. DETAILS FOR THIS PROCEDURE CAN BE FOUND ON THE TRUCK BODY BUILDER ADVISORY SERVICE (BBAS) WEBSITE, FOUND BY CLICKING THE LINK AT THE BOTTOM OF THE WEBPAGE AT HTTPS://WWW.FLEET.FORD.COM. ONCE AT BBAS WEBSITE, CLICK ON BULLETINS, AND REFER TO PUBLISHED QUALIFIED VEHICLE MODIFIER (QVM) BULLETIN FOR DUAL TO SIGNAL GENERATOR CONVERSION. CHANGES TO GENERATOR SETUP AS A RESULT OF UPFITTER MODIFICATIONS ARE NON-WARRANTABLE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SUPER DUTY, E-SERIES, F53 MOTORHOME, F59 CHASSIS, F-650/750 VEHICLES EQUIPPED WITH A 6.8L ENGINE WITH AN ENGINE BUILT ON 10-SEP-2016 AND THROUGH 15-FEB-2017 MAY EXHIBIT MULTIPLE MISFIRE DIAGNOSTIC TROUBLE CODES (DTCS) P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0306, P0307, P0308, P0309, P0309 AND/OR P0310. THIS MAY BE DUE TO AN UNDER TORQUED CRANKSHAFT PULLEY BOLT. BEFORE ATTEMPTING ANY DIAGNOSIS OR REPAIRS, SUSPECT UNDER TORQUED CRANKSHAFT PULLEY BOLT AS THE ISSUE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SUPER DUTY VEHICLES EQUIPPED WITH BLIS THAT HAVE HAD THE PICKUP BOX REMOVED FOR UPFITTER MODIFICATION MAY EXHIBIT A BLIS WARNING MESSAGE IN THE MESSAGE CENTER. TO CORRECT THIS CONCERN, USE INTEGRATED DIAGNOSTIC SYSTEM (IDS) SERVICE TOOL VERSION 104.01 OR LATER TO CONFIGURE THE BLIS SYSTEM. THESE SETTINGS CAN BE FOUND UNDER TOOLBOX > MODULE PROGRAMMING > PROGRAMMABLE PARAMETERS > WARNING LAMPS AND CHIMES AND MUST BE ADJUSTED IN MULTIPLE MODULES. DETAILS CAN BE FOUND ON THE TRUCK BODY BUILDER ADVISORY SERVICE (BBAS) WEBSITE, FOUND BY CLICKING THE LINK AT THE BOTTOM OF THE WEBPAGE AT HTTPS://WWW.FLEET.FORD.COM. ONCE AT BBAS WEBSITE, CLICK ON BULLETINS, AND REFER TO PUBLISHED QUALIFIED VEHICLE MODIFIER (QVM) BULLETIN FOR BLIS WARNING PROGRAMMING. CHANGES TO BLIS SETUP AS A RESULT OF UPFITTER MODIFICATIONS ARE NON-WARRANTABLE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DURING PRE DELIVERY INSPECTION (PDI), 2017 F-SUPER DUTY VEHICLES WILL EXHIBIT AN ILLUMINATED LOW TIRE PRESSURE WARNING LIGHT AND LOW TIRE PRESSURE READOUTS IN THE MESSAGE CENTER (IF EQUIPPED) FROM THE FACTORY. WHEN INFLATING THE TIRES TO SPECIFICATION UTILIZING A DIGITAL TIRE PRESSURE GAUGE, DO NOT REFERENCE THE PRESSURE DISPLAYED IN THE MESSAGE CENTER FOR CURRENT TIRE PRESSURE. ALSO, IT IS NOT NECESSARY TO TRAIN OR ACTIVATE SENSORS WITH THE SERVICE TOOL DURING PDI. TO CORRECT THE PRESSURE READOUTS AND CLEAR THE WARNING MESSAGE, DRIVE THE VEHICLE FOR 2 MILES OR 2 MINUTES AT OVER 32 KPH (20 MPH) DURING THE ROAD TEST PORTION OF THE PDI WORKSHEET. IF THE TPMS LOW TIRE PRESSURE WARNING IS STILL PRESENT OR MESSAGE CENTER PRESSURE READOUT IS INACCURATE AFTER COMPLETING PDI, REFER TO THE ONLINE WORKSHOP MANUAL, SECTION 204-04B FOR NORMAL DIAGNOSTICS.
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SERIES SUPER DUTY PICKUPS EQUIPPED WITH A REAR AUXILIARY POWER POINT MAY REMAIN RUNNING AFTER THE IGNITION IS TURNED OFF. PRIOR TO PERFORMING ANY DIAGNOSTICS, INSPECT THE REAR AUXILIARY POWER POINT FOR ANY AFTERMARKET DEVICES THAT CAN SUPPLY VOLTAGE BACK INTO THE VEHICLE. ITEMS SUCH AS A BATTERY JUMP PACK CAN INDUCE VOLTAGE THAT WILL SIMULATE KEY ON STATUS AND PREVENT THE POWERTRAIN CONTROL MODULE (PCM) FROM SHUTTING OFF THE ENGINE. IF NO AFTERMARKET DEVICES CAN BE LOCATED, REFER TO WORKSHOP MANUAL (WSM), SECTION 211-05 FOR NORMAL DIAGNOSTICS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SUPER DUTY VEHICLES EXHIBIT CONCERNS RELATED TO BRAKE DRAG. UTILIZE WORKSHOP MANUAL (WSM) DIAGNOSTICS IN SECTION 206-00 TO VERIFY THE CORRECT INSTALLATION OF THE STOPLAMP SWITCH. IMPROPER ADJUSTMENT OF THE STOPLAMP SWITCH CAN CAUSE THE BRAKE PEDAL ASSEMBLY TO LIGHTLY APPLY THE BRAKES RESULTING IN DRAGGING CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ON 2017 F-SUPER DUTY, THE INSTALLATION AND CONFIGURATION OF THE FACTORY SUPPLIED UPFITTER AUXILIARY SWITCHES AND/OR THE UPFITTER INTERFACE MODULE COMPONENTS CANNOT BE ADDED TO A VEHICLE THAT WAS NOT BUILT WITH THIS OPTION AT PRODUCTION. CHASSIS CABS CONFIGURATIONS WILL ONLY HAVE THE UPFITTER SWITCHES AS STANDARD EQUIPMENT. FURTHER INFORMATION CAN BE FOUND ON THE TRUCK BODY BUILDER ADVISORY SERVICE (BBAS) WEBSITE, FOUND BY CLICKING THE LINK AT THE BOTTOM OF THE WEBPAGE AT HTTPS://WWW.FLEET.FORD.COM. ONCE AT BBAS WEBSITE, CLICK ON BULLETINS, AND REFER TO PUBLISHED QUALIFIED VEHICLE MODIFIER (QVM) BULLETIN FOR 2017 F-SUPER DUTY UPFITTER AUXILIARY SWITCHES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SUPER DUTY VEHICLES BUILT ON OR BEFORE 23-JAN-2017 MAY EXHIBIT A WATER LEAK INTO THE PASSENGER COMPARTMENT DUE TO POOR SEALING OF THE CAB MARKER LAMP GASKET. IF THE WATER LEAK IS DETERMINED TO BE FROM THE CAB MARKER LAMP, A REVISED CAB MARKER LAMP ASSEMBLY IS AVAILABLE THAT HAS ADHESIVE ON THE GASKET TO IMPROVE SEALING. WHEN INSTALLING THE ROOF MARKER LAMP, REFER TO WORKSHOP MANUAL (WSM), SECTION 417-01 FOR REVISED INSTALLATION PROCEDURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2017 F-SUPER DUTY EQUIPPED WITH A 6.7L ENGINE MAY EXHIBIT A MIL ON WITH DTC P06A6, P0193, P02E9, P0335, P0532 AND/OR P2454. THIS MAY BE DUE TO A CONCERN WITH THE REFERENCE VOLTAGE OR SIGNAL RETURN CIRCUIT OF THE CRANKSHAFT POSITION SENSOR (CKP) WIRING. INSPECT CKP SENSOR HARNESS CIRCUITS APPROXIMATELY 381MM(15 INCHES) FROM THE CKP SENSOR CONNECTOR FOR DAMAGE OR EVIDENCE OF BEING PINCHED. IF A WIRING CONCERN IS FOUND, REPAIR AS DIRECTED PER WIRING DIAGRAM SECTION 5. USE CAUSAL PART 12B637 AND UTILIZE APPLICABLE LABOR OPERATIONS FROM SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2016 F-150, 2017 F-SUPER DUTY VEHICLES MAY HAVE CONCERNS WHERE THE INSTRUMENT CLUSTER DEFAULTS BACK TO THE TRAILER TOW SETUP SCREEN EVERY KEY CYCLE WITH NO TRAILER ATTACHED. REFER TO THE INFORMATION DISPLAY SECTION OF THE OWNERS MANUAL OR THE FOLLOWING STEPS TO CORRECT THIS CONCERN. TYPE 1 AND 2 CLUSTER SMALL DISPLAY USE THE INFORMATION DISPLAY CONTROLS ON THE STEERING WHEEL AND THE INFORMATION DISPLAY MENU. NAVIGATE TO TOWING AND PRESS OK, SELECT TRAILER OPTIONS AND PRESS OK, CHOOSE SELECT TRAILER AND PRESS OK, FINALLY SELECT NO ACTIVE TRAILER AND PRESS OK. TYPE 3 CLUSTER LARGE DISPLAY USE THE INFORMATION DISPLAY CONTROLS ON THE STEERING WHEEL AND THE INFORMATION DISPLAY MENU. NAVIGATE TO TOWING TAB, SELECT TRAILER SETUP AND PRESS OK, THEN PRESS OK TO ENTER TRAILER OPTIONS, SELECT CHANGE TRAILER SELECTED AND PRESS OK, FINALLY SELECT NO ACTIVE TRAILER AND PRESS OK.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2005-2017 F-SUPER DUTY 4X4 VEHICLES OPERATED IN EXTREME DUST, MUD OR TAR SAND CONDITIONS MAY EXHIBIT ACCELERATED 4X4 VACUUM HUB SEAL AND OR WHEEL BEARING WEAR AS A RESULT OF HARSH OPERATING CONDITIONS. A KNUCKLE SEAL SHIELD KIT IS NOW AVAILABLE FOR CUSTOMER PURCHASE. THE KIT IS DESIGNED FOR SEVERE DUTY AND IS NON WARRANTABLE. THE KNUCKLE SEAL SHIELD KIT GC3Z-54024A38-A INCLUDES AN INSTRUCTION SHEET.
NHTSA source summary · Original PDF not reviewed by Recallfolio
REPLACING THE ORIGINAL EQUIPMENT SYNC/NAVIGATION SYSTEM WITH EITHER AN AFTERMARKET SYNC/NAVIGATION KIT OR MODIFYING ORIGINAL SYNC/NAVIGATION PARTS TO PROVIDE ADDITIONAL FEATURES IS NOT RECOMMENDED NOR SUPPORTED ON ANY FORD, MERCURY OR LINCOLN VEHICLE. ONLY APPROVED GENUINE FORD ACCESSORIES OR ORIGINALLY INSTALLED SYSTEMS ARE SUPPORTED AND CERTIFIED TO FUNCTION CORRECTLY WITH OTHER VEHICLE SYSTEMS. IF YOU SUSPECT A SYSTEM HAS BEEN MODIFIED, THE FOLLOWING RESOURCES CAN BE USED TO VERIFY ORIGINAL EQUIPMENT: MONRONEY LABEL (WINDOW STICKER), PROFESSIONAL TECHNICIAN SOCIETY (PTS) OASIS TAB SELECT SYNC OR HVBOM. FOR GENUINE FORD ACCESSORIES USE: PTS WORKSHOP TAB SELECT DEALER INSTALLED ACCESSORY OR ACCESSORY INSTALLATION.