2019 Ford F-250 SD Manufacturer communications & TSBs.Page 3
Original record summaries, dates and identifiers for this model-year. Records 201–249 of 249, ordered newest first. Dated records on this page: Sep 3, 2018–May 13, 2019.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
May 13, 2019Service Bulletin/Repair Instructions
TSB19-2142
NHTSA communication ID: 10160870
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty chassis cab/dual rear wheel (DRW) pickup vehicles and 2016-2019 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit a concern of oil consumption in applications where the engine is idled for extended periods of time. This may be due to high crankcase pressure as a result of the crankcase ventilation filter element becoming restricted. To correct the condition, follow the Service Procedure steps to replace the crankcase oil separator. The new crankcase vent oil separator appears different from the old crankcase vent oil separator as it no longer includes a serviceable filter element. Follow the service procedure steps to correct the condition.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
NHTSA source summary · Original PDF not reviewed by Recallfolio
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47949 - 2017-2019 F-Super Duty - LED Headlamps - DTC U2100 Some 2017-2019 F-Super Duty vehicles may exhibit a diagnostic trouble code (DTC) U2100 in the body control module B (BCMB). Vehicles equipped with factory LED headlamps do not require a BCMB to operate the headlamps. If equipped with LED headlamps, the U2100 DTC should be ignored. It will not affect the performance of the LED headlamps or other systems that control exterior and interior lighting. Do not attempt any repairs.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING:HEADLIGHTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles equipped with a 6.7L engine built on or before 9-Jan-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P2074 and/or P0170. This may be due to various strategies within the powertrain control module (PCM) software. To resolve this condition, reprogram the PCM and perform a mass air flow (MAF) parameter reset.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015 - 2019 Model Year F-150 and 2017 â 2019 Model Year F-Super Duty Vehicles Equipped with Engine Block Heaters - Engine Block Heater Cord Replacement
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47903 - 2018-2019 F-150/F-Super Duty/Transit - Rear Axle Pinion Seal Fluid Leak/Seepage Some 2018-2019 F-150, F-Super Duty, and Transit vehicles may exhibit the appearance of a fluid leak or seepage from the rear axle pinion seal. The appearance of a fluid leak or seepage on a vehicle with less than 500 miles or less than 3 months in service may not be due to a failed rear axle pinion seal. The appearance of fluid around the seal may be from the axle assembly being shipped to the vehicle assembly plant with the pinion facing down. To determine if a leak is present, clean the seal area of any residual lubricant and visually inspect the pinion seal for leaks or damage in the seal contact area or dust slinger on the pinion flange dust shield. If no concerns are found, run the vehicle on a hoist in DRIVE at idle speeds for 10 minutes to allow the fluid to circulate and recheck for signs of leakage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty, 2017-2019 Continental, and 2016-2018 Explorer/Police Interceptor Utility vehicles may exhibit a crank/no start condition, inoperative trailer tow lighting and/or inoperative power telescoping mirrors. This may be due to a concern within the battery junction box (BJB) relay module. A lower level service part has been released to allow for replacement of just the BJB relay module instead of the BJB harness. F-Super Duty part number HU5Z-14A067-A, Continental part number GU5Z-14A067-C, Explorer part number FU5Z-14A067-A, Police Interceptor Utility part number GU5Z-14A067-B.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 F-150 vehicles built at Kansas City Assembly Plant on 4-Apr-2018 and through 4-Mar-2019 and Dearborn Truck Plant on 13-Apr-2018 and through 26-Feb-2019 and some F-Super Duty vehicles built at Kentucky Truck Plant on 22-Apr-2018 and through 5-Mar-2019 and Ohio Assembly Plant on 18-Apr-2018 and through 11-Mar-2019 may exhibit doors that are difficult to unlatch or latch in cold or below freezing temperatures. This may be due to water entering the doors causing door latching components to freeze. To correct the condition, install the service kit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty chassis cab/dual rear wheel (DRW) pickup vehicles and 2016- 2019 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an oil consumption concern in applications where the engine is idled for extended periods of time. This may be due to high crankcase pressure as a result of the crankcase ventilation filter element becoming restricted. To resolve the concern, replace the crankcase vent oil separator. The new crankcase vent oil separator appears different from the old crankcase vent oil separator as it no longer includes a serviceable filter element.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty, 2017-2019 Continental, 2016-2019 Edge, 2016-2018 MKX, 2019 Nautilus vehicles may exhibit a U3000:49 diagnostic trouble code (DTC) setting in the Steering Effort Control Module (SECM) with no other DTCs present. To eliminate the DTC, perform the IDS SASM module reset routine. The IDS reset routine is available under Toolbox > Chassis > Steering > Adaptive Front Steering > SASM Module Reset. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. For claiming, use causal part 3600 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty and 2016-2019 F-650/F-750 vehicles built on or after 1-Oct-2017 equipped with a 6.7L engine may exhibit an intermittent oil pressure warning lamp. A revised oil pressure switch has been released; service part number GC3Z-9278-B. For removal and installation of the oil pressure switch refer to Workshop Manual, Section 303-01C. Applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual
NHTSA source summary · Original PDF not reviewed by Recallfolio
2017-2019 F-Super Duty, 2017-2019 Continental, 2015-2019 Edge, 2016-2018 MKX and 2019 Nautilus vehicles may exhibit an inoperative heated steering wheel. For vehicles equipped with adaptive steering, the steering effort control module (SECM) controls the heated steering wheel feature and is internal to the vehicle's steering wheel. For vehicles not equipped with adaptive steering, the heated steering wheel module (HSWM) controls the heated steering wheel feature and is separate from the steering wheel. Using the OASIS Tab drop down > HVBoM > Features button or an appropriate Ford diagnostic scan tool, you can determine if the vehicle is equipped with Adaptive Steering. Refer to the Workshop Manual (WSM), Section 211-05.
Source components: STEERING · STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
Source components: ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) U029D and/or P2209 in the powertrain control module (PCM). This may be due to water intrusion.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) U029D and/or P2209 in the powertrain control module (PCM). This may be due to water intrusion.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles may require a coax cable repair for a concern with one or more inoperative cameras, cameras with poor image quality, or radio reception concerns. A lower level coax cable harness service part is now available. Refer to the parts catalog using base part number 14D202.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles may require a coax cable repair for a concern with one or more inoperative cameras, cameras with poor image quality, or radio reception concerns. A lower level coax cable harness service part is now available. Refer to the parts catalog using base part number 14D202.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles may exhibit concerns related to brake drag. Utilize Workshop Manual (WSM) diagnostics in section 206-00 to verify the correct installation of the stoplamp switch. Improper adjustment of the stoplamp switch can cause the brake pedal assembly to lightly apply the brakes resulting in dragging condition
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles equipped with a 6.7L engine built on or before 9-Jan-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with DTCs P2074 and/or P0170. Follow the Service Procedure steps to correct the condition.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles may exhibit concerns related to brake drag. Utilize Workshop Manual (WSM) diagnostics in section 206-00 to verify the correct installation of the stoplamp switch. Improper adjustment of the stoplamp switch can cause the brake pedal assembly to lightly apply the brakes resulting in dragging condition
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles equipped with a 6.7L engine built on or before 9-Jan-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with DTCs P2074 and/or P0170. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles equipped with a 6.2L or 6.8L gas engine may exhibit multiple warning indicators in the instrument panel cluster and/or inoperative radio during snow plow use. Battery state of charge is important to verify prior to any repairs. 12.72v to 12.8v is a fully charged battery. To assist with the investigation use the Report a Vehicle Concern link at the bottom of the OASIS report and include the following information: What brand of plow the vehicle is equipped with, If it's been equipped by the plow manufacturer's specifications, If other equipment is up-fitted on the vehicle, ambient temperature when the concern occurs, Engine RPM and MPH/KPH, and battery state of charge. Note the concern should be duplicated similar to customer use and ambient temperature.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles equipped with a 6.2L or 6.8L gas engine may exhibit multiple warning indicators in the instrument panel cluster and/or inoperative radio during snow plow use. Battery state of charge is important to verify prior to any repairs. 12.72v to 12.8v is a fully charged battery. To assist with the investigation use the Report a Vehicle Concern link at the bottom of the OASIS report and include the following information: What brand of plow the vehicle is equipped with, If it's been equipped by the plow manufacturer's specifications, If other equipment is up-fitted on the vehicle, ambient temperature when the concern occurs, Engine RPM and MPH/KPH, and battery state of charge. Note the concern should be duplicated similar to customer use and ambient temperature.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 F-150 vehicles built at Kansas City Assembly Plant on or after 4-Apr-2018 and Dearborn Truck Plant on or after 13-Apr-2018 and some F-Super Duty vehicles built at Kentucky Truck Plant on or after 22-Apr-2018 and Ohio Assembly Plant on or after 18-Apr-2018 may exhibit doors that are difficult to unlatch or latch in temperatures at or below freezing. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2018 Expedition/Navigator, 2018-2019 F-Super Duty and 2019 E-Series/F-650/F-750 vehicles built on or after 9-Jul-2018 and 2019 F-150/Transit vehicles built on or after 2-Jan-2019 are filled with the new Motorcraft Yellow Antifreeze/Coolant. When servicing the cooling system(s) on these vehicles, use Motorcraft Yellow Antifreeze/Coolant VC-13-G (CVC-13-G for Canada). Do not mix different colors or types of coolant. NOTE: The Motorcraft Yellow Antifreeze/Coolant may appear green in color due to the florescent dye used.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 F-Super Duty vehicles equipped with a 6.7L engine built on or before 21-Aug-2018 may exhibit an illuminated MIL with DTC P205B stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty and 2016-2019 F650-750 with 6.7L diesel engines, 2015-2019 Transit with 3.2L diesel engines and 2018-2019 F-150 with 3.0L diesel engines may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P206C in the powertrain control module (PCM). Review of repair data supports that P206C is often the result of incorrect diesel exhaust fluid (DEF) concentration. Per Powertrain Control/Emissions Diagnosis (PC/ED) Pinpoint Test (PPT) RJ, a DEF concentration reading below 28% will set P206C and cause vehicle derate. If low concentration is suspected, drain fluid and replace with known good DEF before replacing any parts. Low concentration of DEF is not a warrantable condition.
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150, 2017-2019 F-Super Duty, 2018-2019 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit a binding/sticking, glass stuck open or closed, noisy operation including chatter, rattling, or grinding. This may be due to the glass brackets cracking and/or breaking apart. The glass panel brackets are serviceable separately from the frame assembly and require the roof opening panel glass to be moved to the vent position. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2018 Model Year F-150, 2019 Model Year F-250 through F-550 Superduty and 2019 Model Year F-650 through F-750 Medium Duty Vehicles Equipped with a Diesel Engine - Powertrain Control Module Reprogramming
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:ENGINE:DIESEL · FUEL SYSTEM, DIESEL · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles may exhibit a headliner edge that shows around the overhead console. Using a trim stick or other suitable tool, the headliner should be tucked back in without replacement of the entire headliner.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 F-Super Duty vehicles equipped with a 6.7L engine built on 1-Dec-2017 and through 1-Aug-2018 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P2122, P2127, U0401, U0109, P0480, P008A, P025C, P027A and/or P064A. This may be due to powertrain control module (PCM) connector C1232B not being properly seated to the PCM.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.
Source components: STEERING · STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles may exhibit a whistle type noise from under the hood while under load and/or while driving. Make sure there is a proper connection between the air cleaner lower intake duct, located under the battery tray, and the air cleaner. Refer to Workshop Manual (WSM), Section 303-12C and WSM, Section 414-01 for further information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2014-2016 Model Year F-250 ? F-550 and 2016 Model Year F-650 - F-750 Vehicles, With 6.7L Diesel Engine - Crankcase Ventilation Oil Separator Assembly. Certain 2018 Model Year F-150 and 2019 Model Year F-250 through F-550 Superduty Vehicles Equipped with a Diesel Engine - Powertrain Control Module Reprogramming
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV) · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles and 2018 Expedition/Navigator vehicles may exhibit a concern where the radio reverts to an AM or FM station after shutting the vehicle off, leaving it off for at least 20 minutes, and then starting it back up. Do not perform any repairs for this concern. If a vehicle exhibits this concern, please use the Report a Vehicle Concern link at the bottom of the OASIS tab and submit a report. Engineering is investigating. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty/2018 F-150 vehicles equipped with the 6.7L or 3.0L engines may exhibit an illuminated malfunction indicator lamp (MIL) with DTC P208E in the powertrain control module (PCM). When performing pinpoint test RK, the results of the selective catalyst reductant (SCR) dosing measurement test (RK7) may be zero or below the specified 40-50mL requirement due to urea crystals plugging the DEF injector nozzle. If the measurement is below this specified amount, perform pinpoint test step RK7 two additional times. If the specified amount is met, reinstall the reductant injector. If after three attempts the dosing measurement remains below the specified amount, the DEF injector should be replaced. The DEF pump should not be replaced for DTC P208E. Engineering is investigating. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated MIL with only DTC P2074 stored in the powertrain control module (PCM). Do not replace the PCM or mass air flow (MAF) sensor for this concern. Instead perform a MAF parameter reset under: Toolbox - Powertrain - Service Functions - Reset/Clear Specified Function - Reset/Clear Functions - MAF Sensor. Engineering is investigating. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2019 F-Super Duty fleet-only vehicles equipped with a telematics control unit (TCU) may have DTC B1D55 present. These vehicles are not equipped with a secondary antenna due to the fleet-only TCU not requiring a secondary antenna input. If DTC B1D55 is present, but there is no sail antenna present (roof mounted antenna with a small fin), then no repairs should be performed for this DTC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-250/F-350 4WD vehicles built on or before 31-Jul-2018 may exhibit a sustained steering wheel oscillation after hitting rough pavement or an expansion joint above 45 mph (72 Km/h). Follow the Service Procedure steps to correct the condition.