2023 Ford F-150 Manufacturer communications & TSBs.Page 1
Original record summaries, dates and identifiers for this model-year. Records 1–100 of 377, ordered newest first. Dated records on this page: Jun 19, 2025–Sep 3, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Sep 3, 2026Service Bulletin/Repair Instructions
TSB 26-2391
NHTSA communication ID: 11037297
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin updates 26-2206. Reason for update: update the Service Procedure to revise Steps 19-21, adding Step 22, and adding Figure 15-16 to clarify connector C316 location. Some of the vehicles listed in the Model statement above may exhibit diagnostic trouble codes (DTCs) C1001:31, U3000:89, and/or U3000:49 stored in the image processing module A (IPMA) and at least one of the following conditions: "Front Camera Fault Service Required" message Pre-collision assist inoperative Adaptive cruise control inoperative Front windshield camera alignment routine fails to complete This may be due to the coaxial cable between the IPMA camera and the IPMA.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes 26-2287. Reason for update: update the labor operation numbers to add MT to operations C, F, G, H, J, K, L and M, and correct the part number LIMZ-4A015-B to L1MZ-4A015-B. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Harsh engagement Delayed engagement Harsh shift Delayed shift Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC)s P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to axial movement of the CDF clutch cylinder sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as ne
Source components: ELECTRICAL SYSTEM · POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For Various Ford and Lincoln vehicles, if diagnostics lead to the replacement of the front seat cushion cover J-clips, lower-level service parts are now available. Use service part W709919-S901 if the J-clip is completely detached from the seat cover and W715386-S424 if the clip is still partially attached. It is not necessary to replace the seat cover if only the J-clip is separating from the cover. Refer to PTS Home > Technical Assistance > Technical Support Videos > Section 501- Body and Paint > Seat J-Clips. For claiming, use causal parts from list below and labor operations 63100A and 63100A5. Causal Parts for claiming: Bronco/Bronco Sport/Escape/Explorer/Expedition/Navigator: 7862900 or 7862901 F-150/F-Super Duty: 1562900 or 1562901 Ranger/Maverick: 6062900 or 6062901
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2026 F-150 Lightning vehicles may exhibit a reduced distance to empty (DTE) projection, a high voltage battery pack state of charge (SOC) that drops from 100% to less than 90% within 60 seconds of being driven, and an inability to reach a target SOC using the scheduled charging feature without any diagnostic trouble codes (DTCs) in the battery energy control module (BECM). This may be due to an issue in one or more cells within the high voltage battery pack. To correct the condition, run the "BECM Battery Health" application using the latest software version of the Ford Diagnosis and Repair System (FDRS). If any cells are identified as exceeding state of charge and/or capacity thresholds, refer to the Workshop Manual (WSM), Section 414-03A High Voltage Battery, Mounting and Cables > Diagnosis and Testing > High Voltage Battery, Mounting and Cables Electric. Perform Pinpoint Test High Voltage Battery Pack Cell Balancing Faults, Step 4 (PPT Step AO4 for 2022-2024 vehicles/PPT Step AQ4 for 2024-2026 vehicles) and proceed with Pinpoint Test directions following the results of Step 4.
Source components: ELECTRICAL SYSTEM · FUEL/PROPULSION SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 F-150 vehicles may exhibit a concern of the windshield wipers not parking in the correct position on the windshield and/or over-traveling. This may be due to incorrect alignment of the wiper pivot arm on the wiper linkage assembly. Wiper pivot arms may or may not be equipped with an alignment key. Alignment keys are a manufacturing aid and are not needed for proper alignment and operation. In some instances, it may be necessary to remove this alignment key to achieve proper alignment. Replacement of the wiper pivot arm, due to a missing alignment key is a not warrantable. Refer to Workshop Manual (WSM), Section 501-16.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model Statement above may exhibit an intermittent extended crank with no relevant diagnostic trouble codes (DTCs) present. This may be due to various software parameters in the powertrain control module (PCM).
Source components: ELECTRICAL SYSTEM · FUEL/PROPULSION SYSTEM · POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine, 2020-2026 Explorer vehicles equipped with a 3.3L hybrid engine, and 2020-2023 Lincoln Aviator vehicles equipped with a 3.0L EcoBoost hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the belt integrated starter generator (BISG). For vehicles with this condition, follow the necessary Pinpoint Test in Workshop Manual (WSM), Section 303-06 for DTC P0A1E and repair the vehicle as directed. Note that previous replacement of the BISG does not negate the need for subsequent BISG replacements if directed to do so by the appropriate Pinpoint Test diagnostics. Engineering is investigating this BISG quality concern. Monitor PTS for updates regarding this investigation.
Source components: ELECTRICAL SYSTEM · FUEL/PROPULSION SYSTEM · POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
Source components: ELECTRICAL SYSTEM · FUEL/PROPULSION SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Ford and Lincoln vehicles may exhibit an "Updating SYNC" message on the vehicle center display screen after an over the air (OTA) update. The message can be cleared from the center display screen and SYNC can be used normally, but it will re-appear at every subsequent ignition cycle. Inform customers that engineering is currently working on a software update solution for this condition to be delivered OTA expected in late Q3 2026. Software will update automatically if vehicle connectivity is enabled in the vehicles settings. Monitor Professional Technician System (PTS) for additional information.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 Ford vehicles may exhibit inoperative heated/cooled seats, heated steering wheel and/or front/rear defrost features after a remote start is performed through the Ford mobile application or with the key fob. Customers may also experience heated/cooled seats, heated steering wheel and/or front/rear defrost features turning on in unexpected conditions such as during warmer weather. These features will operate normally when commanded in the center display screen. This may be due to the customer not setting up their "Climate Settings" through the Ford mobile application. To correct this condition, inform the customer they should perform a remote start from the Ford mobile application and then adjust the "Climate Settings" in the Ford mobile application as desired. These settings only need to be set once and will persist through subsequent remote starts. Heated and cooled seats will be set to Level 2 when turned ON via "Climate Settings" in the Ford mobile application during a remote start event. This is normal operating characteristic. This condition does not affect vehicle durability and no a
Source components: ELECTRICAL SYSTEM · SEATS · UNKNOWN OR OTHER · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NEW VEHICLE DELIVERY HOLD - Emissions Recall 26E04 Certain 2021-2025 Model Year F-150, Maverick, Mustang, Ranger, Expedition, Bronco Sport, Explorer, Bronco, Navigator, and Aviator Vehicles Powertrain Control Module Software Update
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 26-2066. Reason for update: To remove "(2024 only)" from the Issue statement to include 2021-2025 vehicles that may exhibit a clicking sound coming from the gear shift lever. Some of the vehicles listed in the Model statement above equipped with a console GSM may exhibit at least one of the following conditions: * Clicking sound coming from the gear shift lever after it is placed and kept in reverse, neutral or drive position. * Gear shift lever stuck in park * Gear shift lever will not shift into park * Gear shift lever will not shift out of gear * Gear shift lever will not stow/unstow * Gear shift lever will move past the park position * Loose gear shift lever arm at pivot * Illuminated powertrain malfunction (wrench) indicator with DTCs P0929:77, P0929:00, P0929:07 and/or P0929:9A stored in the GSM This may be due to the GSM. Note: If the gear shifter lever will not shift into park, the transmission will automatically shift into park when the return to park function is triggered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 26-2241. Reason For Update: update the parts list to correct the claim quantity of the part number JB3Z-4B496-B from 3 to 6. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 25-2383. Reason for update: to add 2023-2026 F-150 2.7L vehicles. Some of the vehicles listed in the Model Statement may exhibit a vibration/shudder felt during light throttle tip in at highway speeds (8,9,10 gear) with no diagnostic trouble codes (DTC) present. This may be due to various software parameters in the powertrain control module (PCM).
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes 25-2302. Reason for update: update the labor time allowance for F-150 vehicles, update the Parts list to replace the part number W716979-S439 with W721084-S439, and add a note for LV fluids XT-10-QLVC and CXT-10-LV6 "Transfer Case Fluid". Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Harsh engagement Delayed engagement Harsh shift Delayed shift Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC)s P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to axial movement of the CDF clutch cylinder sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other tra
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 F-150 vehicles equipped with a perimeter alarm may exhibit a false alarm activation intermittently. This may be due to the software in the body control module (BCM). Monitor the BCM alarm event parameter identifications (PID). If ALARM_EVT_1/2/3/4 show a value of Intrusion Sensor, reprogram the BCM using the latest software level of the Ford Diagnosis and Repair System (FDRS) diagnostic scan tool. For claiming, use causal part 15604 and labor operations 12651D and BCM.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 F-150 vehicles may exhibit a U2100:00 diagnostic trouble code (DTC) for initial configuration incomplete stored in the trailer control module (TRM). This may be due to the vehicle having a Ford accessory trailer brake kit installed without being programmed following the included instructions. If the vehicle was built with minor feature code FDDAA and a trailer brake gain switch is present in the stock location in the instrument panel, a Ford Accessory trailer brake kit has been installed on the vehicle. If a Ford Accessory trailer brake kit is present, download and run the "TRM - Towbar Configuration" application using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS).
Source components: SERVICE BRAKES · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model Statement above may exhibit a clunking noise from the rear suspension while turning at low speeds. This may be due to binding at the leaf spring clinch clips.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 25-2587. Reason For Update: update the Parts list to add the F-clutch friction plates HL3Z-7B164-D and the F-clutch steel plates PR3Z-7B164-A for the proper vehicle lines, replace the transfer case mounting bolt part number from W714288-S438 to W714288-S437, update the part number W720688-S439 quantity from 2 to 1, update the part number ML3Z-7869-C claim quantity from 2 to 1 (only if necessary), update the description of CXT-10-LV6 and XT-10-QLVC by adding "transfer case fluid, 4WD only", move HL3Z-7A191-B and L1MZ-7F396-A fluid pan gaskets to the parts to inspect and replace list, and remove TL1Z-6775-A self adhesive heat shield from the F-150/Expedition/Navigator parts list as it is not a discard item. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2023-2026 F-150 Raptor R vehicles may experience an intermittent extended crank condition when starting the vehicle with no powertrain related diagnostics trouble codes (DTC) stored in the powertrain control module (PCM). This condition will not prevent the vehicle from starting. This may be due to the software in the PCM. This condition does not affect vehicle durability, and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected by the end of Q3 2026. Replacement or reprogramming of the PCM will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. <br /><br /> If a vehicle exhibits this concern, click on the "Submit Global Concern Report (GCR)" link at the upper right of the PTS Vehicle ID screen (vehicle identification number ÝVIN¨ required) and fill out the form. Do not use the "Report A Problem"
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 26-2130 to update labor operation to reprogram the PCM and check EVAP system from actual time to fixed time, and add extra time to reprogram coordinated modules (if required). Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450 stored in the powertrain control module (PCM). This may be due to the software in the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 26-2116 to clarify the prior approval statement. Some of the vehicles listed in the model statement above may exhibit an oil leak from the oil filter adapter to engine block mounting area. This may be due to block porosity or a block crack just below the oil filter adapter near the main bearing cap outer bolt.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles may exhibit diagnostic trouble code (DTC) U023A:08 in the steering column control module (SCCM) after reprogramming the SCCM with no customer symptoms present. If the vehicles automatic high beam operation is fully functional, this DTC does not affect vehicle operation, and no additional diagnosis or service is required for this condition. Replacement or reprogramming of the SCCM or image processing module A (IPMA) will not resolve this condition. To validate that the automatic high beam system is fully operational, cover the light sensor located in the middle of the dashboard to activate the automatic low beam headlamps. Push the steering wheel multifunction switch forward to cycle through both high beam settings which will be represented in the instrument cluster panel (IPC) as a white telltale (automatic mode - the high beams will not turn on while testing) and a blue telltale (manual mode - the high beams will turn on). If any of the telltales did not illuminate when the steering wheel multifunction switch is pressed forward, refer to the Workshop Manual (WSM)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine and 2020-2026 Explorer vehicles equipped with a 3.3L hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the software within the belt integrated starter generator (BISG). For vehicles with this condition, follow Pinpoint Test I: Battery Isolation/Voltage Stabilization Control Circuit Carry Outance located in the Workshop Manual (WSM), Section 303-06D and repair the vehicle as necessary. Note that the BISG is on backorder status at the time of this publication and Ford is working to make parts available. Engineering is investigating this concern. Monitor PTS for updates.
Source components: ELECTRICAL SYSTEM · ENGINE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article updates TSB 23-2146. Reason for update: clarify prior approval requirements Some of the vehicles listed in the Model statement above may exhibit diagnostic trouble codes (DTCs) C1001:31, U3000:89, and/or U3000:49 stored in the image processing module A (IPMA) and at least one of the following conditions: "Front Camera Fault Service Required" message Pre-collision assist inoperative Adaptive cruise control inoperative Front windshield camera alignment routine fails to complete This may be due to the coaxial cable between the IPMA camera and the IPMA.
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · FORWARD COLLISION AVOIDANCE: WARNINGS · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 F-150 vehicles may exhibit a condition where the intrusion alarm will activate without an external source. This may be due to the software in the body control module (BCM). Reprogramming or replacing the BCM may not resolve this condition. Inform customers that engineering is currently working on a solution for this condition expected by the end of Q2 2026. Inform the customer that the alarm can be disabled every time the ignition is cycled OFF. Refer to the Owner's Manual, "SETTING THE ALARM SECURITY LEVEL" (page 133). Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine and 2020-2026 Explorer vehicles equipped with a 3.3L hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the software within the belt integrated starter generator (BISG). For vehicles with this condition, follow Pinpoint Test G located in the Workshop Manual (WSM), Section 303-06D and repair the vehicle as necessary. Note that the BISG is on backorder status at the time of this publication and Ford is working to make parts available. Engineering is investigating this concern. Monitor PTS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2323 to update the Service procedure, Parts list, and add a clarification note about Cost Cap and Prior approval process requirement for vehicles under NVLW. Some of the vehicles listed in the model statement above may exhibit an oil leak from the oil filter adapter to engine block mounting area. This may be due to block porosity or a block crack just below the oil filter adapter near the main bearing cap outer bolt.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
Source components: ELECTRICAL SYSTEM · LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 20212026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. When referred to a specific clutch (A-F) test by a pinpoint test in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing, the Clutch Assembly tests have been updated with a hyperlink to the new Transmission Line Pressure Test - Pressure Vacuum Transducer (PVT) Is Available procedure in WSM, Section 307-01 > General Procedures. This procedure provides instructions to perform the FDRS Transmission Clutch Circuit Leak Test when applicable. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 F-150 vehicles may exhibit an "Active Air Dam System Fault See Manual" warning message displayed in the instrument panel cluster (IPC) and/or an AAD hanging/not retracting. This may be due to a broken AAD actuator to air dam bolt or bolts. If diagnostics lead to ADD actuator as the causal part, a new lower-level service bolt and u-nut are available. It is not necessary to replace the AAD actuator if only the bolt(s) are damaged.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2246 to update the Service Procedure and add Step 2 to verify the EVAP system integrity after the coordinated software updates. Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450 stored in the powertrain control module (PCM). This may be due to the software in the PCM.
Source components: ELECTRICAL SYSTEM · POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
Source components: POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 F-150 vehicles equipped with a 5.0L/5.2L engine, 2021-2025 F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis vehicles equipped with a 6.8L/7.3L engine and 2021-2025 E-Series/F-650/F-750 vehicles equipped with a 7.3L engine may exhibit a rattle/scraping noise upon startup that may remain after the engine is running. Workshop Manual (WSM),
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2021-2026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. The Workshop Manual (WSM) has been updated under Section 307-01 > Diagnosis and Testing to include this procedure. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Mach-E and 2022-2024 F-150 vehicles may have customers or dealerships that wish to activate new BlueCruise features (example: Lane Change Assist). New BlueCruise features can only be activated/delivered via an over-the-air update (OTA). Inform customers that they will need to wait for the update to be pushed to their vehicle. There is no way to manually push the update. If the update fails, OTA will re-attempt an update later.
Source components: FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · FORWARD COLLISION AVOIDANCE: WARNINGS · LANE DEPARTURE: ASSIST · LANE DEPARTURE: BLIND SPOT DETECTION · LANE DEPARTURE: WARNING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2466 to add Bronco Sport, Escape, Maverick and Corsair, as well as removing Expedition and Navigator. One time use parts for Corsair and Bronco Sport were also added to the parts list. Some of the vehicles listed in the Model statement above may exhibit a headliner rattle or sagging condition around the roof opening panel. This may be due to the adhesive separating from the headliner substrate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit an incorrectly illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0420 and/or P0430 stored in the powertrain control module (PCM). This may be due to the software in the PCM. This condition does not affect vehicle drivability or durability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2579 Reason for update: remove "Lightning" from Labor Times Description Some of the vehicles listed in the Model statement above equipped with a console GSM may exhibit at least one of the following conditions: * Clicking sound coming from the gear shift lever after it is placed and kept in reverse, neutral or drive position. (2024 only) * Gear shift lever stuck in park * Gear shift lever will not shift into park * Gear shift lever will not shift out of gear * Gear shift lever will not stow/unstow * Gear shift lever will move past the park position * Loose gear shift lever arm at pivot * Illuminated powertrain malfunction (wrench) indicator with active DTC P0929:77, P0929:00, P0929:07 and/or P0929:9A stored in the GSM This may be due to the GSM. Note: If the gear shifter lever will not shift into park, the transmission will automatically shift into park when the return to park function is triggered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 20172026 vehicles equipped with a 10R transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 F-150 and 2024-2026 F-Super Duty vehicles equipped with one-touch up/down front windows may exhibit a window not responding to one-touch controls and/or bouncing back when using the one-touch close function.<br /> <br /> For vehicles included in Field Service Action (FSA) 25P35 and/or 26P02, perform repairs as directed by the FSA(s).<br /> <br /> For 2021-2026 vehicles not included in the FSA(s), reprogram the driver door module (DDM) and the passenger door module (PDM) using the latest software level of Ford Diagnosis and Repair System (FDRS) scan tool according to the Workshop Manual (WSM), Section 501-11 for normal diagnostics and testing direction by symptom. For claiming, use causal part 14B291 and labor operation MT14B291SSM, up to 0.4 hours.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 F-150 and 2024-2026 F-Super Duty vehicles equipped with one-touch up/down front windows may exhibit a window not responding to one-touch controls and/or bouncing back when using the one-touch close function.<br /> <br /> For vehicles included in Field Service Action (FSA) 25P35 and/or 26P02, perform repairs as directed by the FSA(s).<br /> <br /> For 2021-2026 vehicles not included in the FSA(s), reprogram the driver door module (DDM) and the passenger door module (PDM) using the latest software level of Ford Diagnosis and Repair System (FDRS) scan tool according to the Workshop Manual (WSM), Section 501-11 for normal diagnostics and testing direction by symptom. For claiming, use causal part 14B291 and labor operation MT14B291SSM.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 F-150, 2022-2025 Expedition/Navigator, 2023-2025 F-Super Duty, 2024-2025 Ranger and 2026 Transit vehicles may exhibit a discharged battery and/or a no crank/no start condition. The vehicle may also exhibit a clicking noise from the trailer module (TRM) while the vehicle is off. This may be due to software in the TRM.<br /><br /> Verify the TRM software part number in the vehicle using Ford diagnosis and repair system (FDRS) to be PC3T-19J297-BF, PC3T-19J297-FF, ML3T-19J297-CD or ML3T-19J297-GD. To confirm a vehicle is equipped with a certain software level, review the software information by hovering over the "Diagnostics" tab in Professional Technician System (PTS) and selecting "Vehicle Software". If one of the listed software part numbers is present, follow the Service Procedure to reprogram the TRM. For vehicles with any other software part number in the TRM, refer to Workshop Manual (WSM), Section 414-01 to continue with normal diagnostics outside of this article. For claiming use causal part 19H332 and labor operation 2006D and 2006D45 of the Service Labor Time Standards (SLTS) Man
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2124 to update the affected model years, customer symptom, causal part and Service Procedure enhancements. Some of the vehicles listed in the Model statement above may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P2796 and/or P2797 stored in the secondary on-board diagnostic control module B (SOBDMB) and/or the secondary on-board diagnostic control module C (SOBDMC). This may be due to the software in the SOBDMB and/or the SOBDMC.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above equipped with one-touch up/down front windows may exhibit a window not responding to one-touch controls and/or bouncing back when using the one-touch close function.<br /><br /> For vehicles effected by Field Service Action (FSA) 25P35, perform repairs as directed by the FSA.<br /><br /> For 2021-2026 vehicles, update the driver door module (DDM) and the passenger door module (PDM) using the latest software level of Ford Diagnosis and Repair System (FDRS) scan tool. Refer to the Workshop Manual (WSM), Section 501-11 for normal diagnostics and repair direction by symptom. For claiming, use causal part 14B291 and service labor operations 12651D and 12651D4.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 F-150, 2022-2025 Expedition/Navigator, 2023-2026 F-Super Duty, 2024-2025 Ranger and 2026 Transit vehicles may exhibit a discharged battery and/or a no crank/no start condition. The vehicle may also exhibit a clicking noise from the trailer module (TRM) while the vehicle is off. This may be due to software in the TRM.<br /><br />Verify the TRM software part number in the vehicle using Ford Diagnosis and Repair System (FDRS) to be PC3T-19J297-BF, PC3T-19J297-FF, ML3T-19J297-CD or ML3T-19J297-GD. To confirm a vehicle is equipped with a certain software level, review the software information by hovering over the "Diagnostics" tab in Professional Technician System (PTS) and selecting "Vehicle Software". If one of the listed software part numbers is present, follow the Service Procedure to reprogram the TRM. For vehicles with any other software part number in the TRM, refer to Workshop Manual (WSM), Section 414-01 to continue with normal diagnostics outside of this article. For claiming, use causal part 19H332 and labor operation 12651D and 12651D4 of the Service Labor Time Standards (SLTS) Man
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 F-150 vehicles may exhibit an inoperative USB media hub with diagnostic trouble code (DTC) B1600:11 stored in the accessory protocol interface module (APIM). Workshop Manual (WSM), Section 415-00 - Information and Entertainment System > Diagnosis and Testing > pinpoint test "A USB (Universal Serial Bus) Input Concern" has been updated to improve diagnostics for this condition.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2513 to update the service procedure and add 2025 affected vehicles. Some vehicles in the Model section above may exhibit an intermittent grinding/hum/rumble noise from the front wheel area while in 2WD that goes away when the vehicle is put into 4WD. These vehicles will also have no diagnostic trouble codes (DTCs) stored in the transfer case control module (TCCM). This may be due to incomplete disengagement of the integrated wheel end (IWE) actuator assemblies. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). Additional Model Information: equipped with an ESOF transfer case (minor feature code FMLAS)
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2276 to update the Service Procedure to include information where to find connector/pin location in wiring diagram and WSM info to perform PMI and TRON for GSM replacement. Some of the vehicles listed in the Model statement above equipped with a console GSM may exhibit at least one of the following conditions: * Clicking sound coming from shifter after it is placed and kept in reverse, neutral or drive position (2024 only) * Shifter stuck in park * Shifter will not shift into park * Shifter will not shift out of gear * Shifter will not stow/unstow * Shifter will move past the park position * Loose shifter lever arm at pivot * Illuminated powertrain malfunction (wrench) indicator with active DTC P0929:77, P0929:00, P0929:07 and/or P0929:9A stored in the GSM This may be due to the GSM. Note: If the gear shifter lever will not shift into park, the transmission will automatically shift into park when the return to park function is triggered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 F-150 vehicles may exhibit a stuck in park condition with no diagnostic trouble codes (DTCs). This may be due to connector C211 pin push out on circuit CCB61 or an open on circuit CCB61 between the antilock brake system (ABS) module and the body control module (BCM). Workshop Manual (WSM), Section 307-05 Automatic Transmission External Controls > Diagnosis and Testing > External Controls - Pinpoint Test for "Stuck In Park" has been updated with improved diagnostics. Refer to revised WSM sections for normal diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 F-150/Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit diagnostic trouble code (DTC) P0299 stored in the powertrain control module (PCM) and may also exhibit a rattle noise from the turbocharger. This may be due to the wastegate actuator rod being disconnected. Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls > Turbocharger has been added to address this condition to allow servicing of the turbocharger actuator rod. In addition, the wastegate actuator rod and associated retention springs and clips have been released as lower level components to complete the repair without replacing the entire turbocharger actuator assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with DTCs P0301-P0306, P0201-P0206 and/or various other powertrain DTCs stored in the PCM. This may be due to the engine harness contacting the hose crimp end or spring clamp tangs on the exhaust heat exchanger heater hose assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2189 to update the service procedure and add 2025 affected vehicles. Some 2021-2025 F-150 non-Raptor vehicles equipped with an ESOF transfer case (minor feature code FMLAS) may exhibit an intermittent grinding/hum/rumble noise from the front wheel area while in 2WD that goes away when the vehicle is put into 4WD. These vehicles will also have no diagnostic trouble codes (DTCs) stored in the transfer case control module (TCCM). To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This may be due to incomplete disengagement of the integrated wheel end (IWE) actuator assemblies.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Expedition/Navigator/F-150/F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis/F-650/F-750/Transit vehicles equipped with a 2.7L/3.5L (non hybrid)/6.8L/7.3L engine and 2021-2026 E-Series may exhibit a rattle/scraping noise from the bellhousing area on start-up. Workshop Manual (WSM), Section 303-00 Engine System - General Information > Diagnosis and Testing and 303-06 > Starting System has been updated to address this condition. Additionally, WSM, Section 303-01 > Removal and Installation > Engine to Transmission Spacer Plate has been added to address this condition. Refer to the revised WSM sections for normal diagnosis.
Source components: ENGINE · POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2025 F-150 vehicles may exhibit a condition where the intrusion alarm will activate without an external source. This may be due to software in the body control module (BCM). Reprogramming or replacing the BCM may not resolve this condition. Inform customers that engineering is currently working on a solution for this condition and it will be released by the end of Q1 2026. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.
Source components: ELECTRICAL SYSTEM · POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 F-150 vehicles equipped with a 5.0L/5.2L engine, 2021-2025 F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis vehicles equipped with a 6.8L/7.3L engine and 2021-2026 E-Series/F-650/F-750 vehicles equipped with a 7.3L engine may exhibit a rattle/scraping noise upon startup that may remain after the engine is running. This may be due to the starter motor drive gear not retracting after starting. To correct this condition, inspect the starter motor drive gear and shaft. If the starter motor drive gear slides back and forth by hand and/or shows signs of scoring or damage, replace the starter motor following Workshop Manual (WSM), Section 303-06 Starting System > Removal and Installation > Starter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2025 F-150 and 2018-2026 F-Super Duty vehicles equipped with a tailgate step may exhibit a step assembly that binds/will not open or opens/pops up while driving. This could be due to an incorrect adjustment of the tailgate step assembly. Before replacing any components for this concern, follow the revised Tailgate Step Adjustment procedure in Workshop Manual (WSM), Section 501-04.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2104 to update the labor times associated with the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Inoperative BlueCruise and lane centering * DTC U2018:51 stored in the camera module - rear (CMR) * DTC U0565:86 stored in the image processing module A (IPMA) * DTC U3000:49 is not stored in the CMR This may be due to the software in the CMR.
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · LANE DEPARTURE: ASSIST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 F-150, 2022-2025 Expedition/Navigator, 2023-2025 F-Super Duty, 2024-2025 Ranger and 2026 Transit vehicles may exhibit a discharged battery and/or a no crank/no start condition. The vehicle may also exhibit a clicking noise from the trailer module (TRM) while the vehicle is off. This may be due to software in the TRM.<br /><br />Verify the TRM software part number in the vehicle using Ford diagnosis and repair system (FDRS) to be PC3T-19J297-BF, PC3T-19J297-FF, ML3T-19J297-CD or ML3T-19J297-GD. To confirm a vehicle is equipped with a certain software level, review the software information by hovering over the "Diagnostics" tab in Professional Technician System (PTS) and selecting "Vehicle Software". If one of the listed software part numbers is present, follow the Service Procedure to reprogram the TRM. For vehicles with any other software part number in the TRM, refer to Workshop Manual (WSM), Section 414-01 to continue with normal diagnostics outside of this article. For claiming use causal part 19H332 and labor operation 12651D and 12651D4 of the Service Labor Time Standards (SLTS)
Source components: ELECTRICAL SYSTEM · FUEL/PROPULSION SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2025 various Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
Source components: ELECTRICAL SYSTEM · LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 F-150 Tremor and Raptor vehicles may be equipped with auxiliary/upfitter switches that do not have rubber tips. Switches no longer equipped with rubber tips is an appearance only change and has no impact on function or performance. Repair or replacement for auxiliary/upfitter switches no longer equipped with rubber tips should not be performed and is not warrantable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Explorer vehicles equipped with a 3.0L EcoBoost engine, 2021-2023 Aviator vehicles equipped with a 3.0L EcoBoost or 3.0L plug-in hybrid electric vehicle (PHEV) engine, 2021-2023 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost, 2021-2024 F-150 vehicles equipped with a 2.7L EcoBoost, and 2021-2024 Bronco and 2024 Ranger vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine. This noise may occur on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to an internal component of the variable cam timing (VCT) unit. Workshop Manual (WSM), Section 303-00 > Diagnosis and Testing > Engine > Pinpoint Test F has been updated to include additional steps along with a video to identify the affected VCT unit that requires replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Expedition/Navigator/F-150/F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis/F-650/F-750/Transit vehicles equipped with a 2.7L,3.5L EcoBoost (non-hybrid), 3.5L Cyclone, 6.8L or 7.3L engine, may exhibit a rattle/scraping noise from the bellhousing area on start-up. Workshop Manual (WSM), Section 303-00 Engine System - General Information > Diagnosis and Testing and 303-06 > Starting System has been updated. Additionally, WSM, Section 303-01 > Removal and Installation > Engine to Transmission Spacer Plate has been added to address this condition. Refer to the revised WSM sections for normal diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit a headliner rattle or sagging condition around the roof opening panel. This may be due to the adhesive separating from the headliner substrate.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2280 to update labor times from M-time to fixed time. Some vehicles listed in the Model statement above, may exhibit an illuminated airbag warning indicator with diagnostic trouble codes (DTCs) U3000:41 and/or U3000:54 in the occupant classification system module (OCSM) and/or B00A0:09, B00A0:63, B00A0:64 and/or B00A0:68 in the restraints control module (RCM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2201 to update the vehicles affected. Some of the vehicles listed in the Model statement above equipped with one-touch up/down front windows may exhibit a window not responding to one-touch controls, not opening all the way and/or bouncing back when using the one-touch close function. This may be due to a calibration parameter in the driver door module (DDM) and/or passenger door module (PDM).
Source components: ELECTRICAL SYSTEM · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2316 to update the Service Procedure and labor operations from M-Time to AP-Time and add a limit. Some of the vehicles listed in the Model statement above, may exhibit an illuminated powertrain temperature warning lamp accompanied by a "Motor Coolant Over Temperature" message in the instrument panel cluster (IPC) with DTC P0A3C:94 stored in either the secondary on-board diagnostic control module B (SOBDMB) and/or the secondary on-board diagnostic control module C (SOBDMC). This may be due to the software within either the SOBDMB and/or SOBDMC.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2023-2025 F-150 vehicles may exhibit a crank/no start with multiple warning indicators and diagnostic trouble code (DTC) U0100 stored in the audio front control module (ACM), gear shift module (GSM), image processing module A (IPMA), power steering control module (PSCM) and instrument panel cluster (IPC). This may be due to an incorrectly tightened ground 104 (G104). Inspect G104 for proper connection, locating tab insertion, and tighten to 8.9 lb-ft (12 Nm). If the condition remains after tightening G104, reference the Workshop Manual (WSM), Section 303-06 outside of this article. For claiming, use causal part 12A581 and labor operations 12650D and 12650D45WR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 F-150 vehicles built on or before 30-Apr-2025 equipped with the 9.75" rear axle (minor feature code EGPAF) may exhibit a drive pinion seal leak. To confirm a vehicle is built with a minor feature code EGPAF, review the build information by double-clicking the vehicle identification number in the upper left-hand corner in the Professional Technician System (PTS). This may be due to the rear axle drive pinion seal. To correct this condition, replace the rear axle drive pinion seal with revised part number NL3Z-4676-A. Refer to Workshop Manual (WSM), Section 205-02. For claiming, use causal part number 4676 and labor operation 4676A.
Source components: POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2253 to update the labor times associated with the Service Procedure from M-time to AP-time and add a limit. Some of the vehicles listed in the Model Statement above, may exhibit a condition where the SelectShift®/SelectShift transmission will downshift to a lower gear when in drive (D) and shifting to a higher gear will be unavailable in the IPC. Downshifting may continue, when safe entry conditions are met for each gear, and the IPC display will show the available gears counting down one by one as the vehicles' speed and engine rpm decreases. This may be due to a chafed wire harness in the SelectShift® +/- circuit.
Source components: ELECTRICAL SYSTEM · POWER TRAIN · VEHICLE SPEED CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2412 to update the labor times from M-time to AP-time and add a limit. Some of the vehicles listed in the Model statement above may exhibit an illuminated engine coolant temperature warning lamp with a "Motor Coolant Over Temperature" message in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) P0A2F:94 stored in the secondary on-board diagnostic control module C (SOBDMC). This may be due to the software level of the SOBDMC.
Source components: ELECTRICAL SYSTEM · ENGINE · FUEL/PROPULSION SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 F-150 vehicles equipped with a B&O audio system (minor feature code IDBBQ), and various 2021-2024 Ford and Lincoln vehicles equipped with a B&O audio system may exhibit a pop noise and/or static in the speakers at start up that cannot be turned down or off using the audio system controls. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner on Professional Technician System (PTS). This may be due to software in the digital signal processing (DSP) module. To correct this condition, reprogram the DSP module to the latest software level using the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 18B849 and labor operations 12651D and 12651D4.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2252 to update the Title, Action Statement, Service Procedure and Part List. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Harsh engagement Delayed engagement Harsh shift Delayed shift Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC)s P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to axial movement of the CDF clutch cylinder sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as necessary as needed to ensure proper function. Add a new line to the repair order to docum
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2021-2025 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit "Please Check Surroundings For Safety" or "Full View Not Available" messages when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.
Source components: UNKNOWN OR OTHER · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2023-2025 F-150 and F-Super Duty vehicles equipped with minor feature code B2DAC may exhibit an inoperative rear passenger window. To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle Information or double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This may be due to an open diode in the window switch. To correct the condition, replace the window switch of the affected window. If the condition persists, continue with normal diagnostics outside of this article. Refer to Workshop Manual, Section 501-11. For claiming, use causal part 14529 and labor operation 14529A of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Quality improvements include: -Latest software update for BlueCruise Activation -Introduction of toggles in the center screen for driver assist features -Improved audio experience while using CarPlay or Android Auto"
Campaign / software reference: SYNC-25.2.1.6.5
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Ford and Lincoln vehicles equipped with SYNC4/Digital Experience may exhibit an unsuccessful telematics control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer, 2022-2023 F-150, and 2023-2024 Expedition/Navigator vehicles equipped with a 2.3L/3.5L EcoBoost engine may exhibit may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P25B3, P25B4, P25B5, P25B6, P2ABA, P2ABB, P2ABC, P2AB7, P2AB8, and/or P2AB9 stored in the powertrain control module (PCM). This may be due to a concern with the turbocharger wastegate. To correct the condition, follow the applicable diagnostic pinpoint tests (PPT) steps found in Workshop Manual (WSM), Section 303-04 and repair as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2195 to update the labor times from M-time to fixed time. Some of the vehicles listed in the Model statement above may exhibit an illuminated MIL in the instrument panel cluster (IPC) with DTC P0171 stored in the powertrain control module (PCM). This may be due to the software level of the PCM.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2276 to update the service procedure to include information where to find connector/pin location in wiring diagram and WSM info to perform PMI and TRON for GSM replacement. Some of the vehicles listed in the Model statement above equipped with a console gear shift module (GSM) may exhibit at least one of the following conditions: * Clicking sound coming from shifter after it is placed and kept in reverse, neutral or drive position (2024 only) * Shifter will not shift out of park/into park * Shifter will not shift out of gear * Shifter will not stow/unstow * Shifter will move past the park position * Loose shifter lever arm at pivot * Illuminated powertrain malfunction (wrench) indicator with active DTC P0929:77, P0929:00, P0929:07 and/or P0929:9A stored in the GSM This may be due to a faulty GSM and/or connector C211 pin push out on circuit CCB61 or an open on circuit CCB61, between the anti-lock brake system (ABS) module and the body control module (BCM). Note: If the gear shifter lever will not shift into park, the transmission will automatically shift in
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2087 to update Vehicle Application adding 2025 Model Year. Some of the vehicles listed in the model statement may exhibit an oil leak from the oil filter adaptor to engine block mounting area. This may be due to block porosity or a block crack just below the oil filter adapter near the main bearing cap outer bolt.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2364 to update the labor times associated with the Service Procedure from M-time to AP-time. Some of the vehicles listed in the Model Statement above, may DTC P2101 stored in the powertrain control module (PCM). This may be due to the software in the PCM.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 F-150 non-Lightning, 2023-2025 F-Super Duty, 2024-2025 Ranger, and 2025 Explorer vehicles may exhibit a perceived improper functioning fog lamp(s). Customers may describe fog lamps blinking, turning on or off, or flashing. If the vehicle is equipped with cornering lamps, this may be normal function. Under certain conditions and inputs, either lamp might turn on or off independently to aid visibility during cornering. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. For additional cornering lamp information, refer to the Owner's Manual and/or Workshop Manual (WSM), Section 417-01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2023-2025 F-150 Raptor vehicles equipped with a 5.2L engine may exhibit an exhaust rattle/rasp on a cold start. The Workshop Manual (WSM), Section 309-00 Exhaust System - 5.2L 32V Ti-VCT - Supercharged > Diagnosis and Testing > Exhaust system > Pinpoint Test D: Noises Such As Buzzing, Drumming, Thumping, Ringing Or Hissing Coming From Exhaust System has been updated to address exhaust rattling sounds during a cold start lasting for 5 seconds or less as a normal condition. For concerns with exhaust rattles lasting longer than 5 seconds, follow WSM Section 309-00 Exhaust System - 5.2L 32V Ti-VCT - Supercharged > Diagnosis and Testing > Exhaust system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Edge/Nautilus, 2021-2025 Bronco/Bronco Sport/E-Series/Escape/Corsair/Expedition/Navigator/Explorer/Aviator/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2045 to update the production fix date and add model years. Some of the vehicles listed in the Model statement above equipped with a console gear shift module (GSM) may exhibit at least one of the following conditions: * Clicking sound coming from shifter after it is placed and kept in reverse, neutral or drive position (2024 only) * Shifter will not shift out of park/into park * Shifter will not shift out of gear * Shifter will not stow/unstow * Shifter will move past the park position * Loose shifter lever arm at pivot * Illuminated powertrain malfunction (wrench) indicator * DTC P0929:77, P0929:00, P0929:07 and/or P0929:9A This may be due to a faulty GSM and/or connector C211 pin push out on circuit CCB61 or an open on circuit CCB61, between the anti-lock brake system (ABS) module and the body control module (BCM). Note: If the gear shifter lever will not shift into park, the transmission will automatically shift into park when the return to park function is triggered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2443 to update the vehicles affected. Some of the vehicles listed in the Model statement above equipped with the 400-watt direct current/alternating current (DC/AC) inverter system (minor feature code HUKAJ) with a pickup bed alternating current (AC) power outlet socket may exhibit inoperative power outlets with diagnostic trouble code (DTC) B1330:9A stored in the body control module (BCM). This may be due to a connection issue at C4628. NOTE: This article does not apply to vehicles with an inverter system other than the 400-watt DC/AC inverter system with a pickup bed AC power outlet socket.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Ford/ Lincoln vehicles equipped with SYNC4 may not be able to perform an update to the accessory protocol interface module (APIM). This may be due to the software in the APIM. Ford Engineering has de-activated the ability to update these SYNC4 APIM modules as applicable, and the Ford Diagnosis and Repair System (FDRS) will not present an update for the APIM module. Some existing directed repairs may be impacted, check Professional Technician System (PTS) before attempting any specific technical service bulletin (TSB)/special service message (SSM) and check field service action (FSA) landing pages before attempting any FSA repairs. For any vehicle repairs requiring a software update that includes an APIM update in the programming sequence, if the 5-digit product code for the APIM software is equal to or lower than 23187, do not attempt to update affected modules at this time. To determine the 5-digit product code for the APIM software on the vehicle, while the vehicle center display screen is powered up with ignition in run or accessory, go to Settings > General > About SYNC.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.