2020 Ford F-150 Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–200 of 245, ordered newest first. Dated records on this page: Aug 11, 2020–May 17, 2022.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
May 17, 2022Service Bulletin/Repair Instructions
SSM 50786
NHTSA communication ID: 10212120
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150, 2017-2022 Super Duty and 2018-2021 Expedition vehicles may experience a cracked or splitting driver air bag cover. This may be due to the air bag cover tear seam design. An updated driver air bag assembly has been released with a more robust air bag cover design. Refer to Workshop Manual (WSM), Section 501-20B for the replacement procedure. If servicing under warranty, use causal part 15043B13 for F-150 and Expedition or 25043B13 for Super Duty and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 F-150 vehicles equipped with a 3.0L diesel engine, 2016-2022 F-650/F-750 vehicles equipped with a 6.7L engine, and 2017-2022 F-Super Duty vehicles equipped with a 6.7L engine and built on or before 08-Mar-2022 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P21DD, P20BA. P20B9, P204C, P208A, P208B, P208C, P203B, P205B, P21CD and/or U02A2 in the powertrain control module (PCM). This may be due to water intrusion within connectors C3613 and/or C4851/C3610 on the reductant harness going to the reductant pump/heater assembly and the reductant level sensor/quality module. This may also be due to movement of the wiring harness causing terminal fretting. To correct the condition, follow the Service Procedure to replace the reductant tank harness, the reductant pump/heater assembly and/or the reductant tank, as well as securing the wiring harness using a cable zip tie fastener.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 F-150, 2018-2022 Expedition/Navigator/Mustang and 2019-2022 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware break-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2022 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with Diagnostic Trouble Codes (DTCs) P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150- G401, Expedition/Navigator- G403, Transit- G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator- G407) and confirm FPCM connector (F-150- C4336, Expedition/Navigator- C433, Transit- C433, 2018-2019 Explorer C3239, 2020-2022 Explorer/Aviator- C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In various 2017-2022 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating "Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option
NHTSA source summary · Document-reviewed explainer available below
Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine - Cam Phase Replacement. Parts Requirements / Order information - Intake Gaskets HL3Z-9439-A should be inspected and only replaced if damaged. It is no longer required to replace these gaskets.
Source components: ENGINE AND ENGINE COOLING.
3.5L cam phaser program: Historical deadline: Jan 2023
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2022 F-150 and F-Super Duty vehicles equipped with tailgate step assemblies may exhibit a step assembly that binds/will not open or opens/pops up while driving. This could be due to an incorrect adjustment of the step assembly. Before replacing any components for this concern, follow the Tailgate Step Adjustment procedure in Workshop Manual, Section 501-04, General Procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2022 F-150, 2017-2022 F-Super Duty and 2018-2022 Expedition/Navigator vehicles may exhibit poor air conditioning (A/C) performance, loss of airflow and/or engine cooling fans running continuously from high A/C pressures. This concern may be from the evaporator freezing up due to the evaporator temperature sensor being biased. To correct the condition, follow the Service Procedure steps to replace the evaporator temperature sensor.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 F-150, 2017-2022 F-Super Duty and 2016-2022 F-650/F-750 vehicles equipped with a diesel engine may exhibit diagnostic trouble code (DTC) P0000 stored in the powertrain control module (PCM) after an on-demand self test. This DTC is due to a processing error in the PCM as a result of on-demand self testing. P0000 is an invalid DTC that will not illuminate the malfunction indicator lamp (MIL) and no repairs should be performed.
Source components: EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Focus/MKX/C-MAX, 2017-2019 MKC/Taurus/Flex/MKT, 2017-2020 Fusion/MKZ/Continental, 2017-2022 Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 F-150 vehicles built on or before 01-Feb-2021, 2017-2020 F-150 vehicles equipped with a 3.5L EcoBoost engine, 2018-2020 F-150 vehicles equipped with a 2.7L EcoBoost or 5.0L engine, 2019-2020 F-150 vehicles equipped with a 3.0L diesel engine may exhibit a high pitched squeal or whistle type noise from the engine compartment after the engine is shut off. This condition may be due to the air conditioning (A/C) low side system pressure exceeding the high side pressure resulting in equalization of A/C system pressures through the A/C compressor. An updated A/C compressor has been released to resolve this concern. For claiming, use causal part 19703 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150 vehicles may experience a cracked or splitting driver air bag cover. This may be due to the air bag cover tear seam design. An updated driver air bag assembly has been released with a more robust air bag cover design. Refer to Workshop manual (WSM), Section 501-20B for the replacement procedure. If servicing under warranty, use causal part 15043B13 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 F-150, 2017-2021 Super Duty and 2018-2021 Expedition/Navigator vehicles may exhibit poor air conditioning (A/C) performance, loss of airflow and/or engine cooling fans running continuously from high A/C pressures. This concern may be from the evaporator freezing up due to the evaporator temperature sensor being biased. To correct the condition, follow the Service Procedure steps to replace the evaporator temperature sensor.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2315 to increase the labor operation time allowances. Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang and 2019-2021 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware wear-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 F-150 vehicles equipped with a 5.0L flex fuel engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0171, P0172, P0174 and/or P0175. This may be due to software parameters in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2022 F-Super Duty and 2016-2022 F-650/F-750 with 6.7L diesel engines, 2015-2019 Transit with 3.2L diesel engines and 2018-2021 F-150 with 3.0L diesel engines may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P206C in the powertrain control module (PCM). Review of repair data supports that P206C is often the result of incorrect diesel exhaust fluid (DEF) concentration. Per Powertrain Control/Emissions Diagnosis (PC/ED) Pinpoint Test (PPT) RJ, a DEF concentration reading below 28% will set P206C and cause vehicle derate. If low concentration is suspected, drain fluid and replace with known good DEF before replacing any parts. Low concentration of DEF is not a warrantable condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 Expedition/Navigator, 2018-2020 F-150/Mustang and 2019-2021 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P163E stored in the powertrain control module (PCM) or transmission control module (TCM) after replacing the main control valve body. This may be due to software incompatibility between the replacement main control valve body solenoid strategy file and the PCM/TCM software. To correct this condition, follow the Service Procedure to obtain a new main control valve body with a new strategy number.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine Cam Phaser Replacement REASON FOR THIS SUPPLEMENT ⢠Parts Requirements / Ordering Information - Due to limited availability of originally specified parts, alternate option parts have been added. ⢠Submitting Claims with Customer Loyalty Program for Balance Remaining â Added instructions on how to use Lincoln Loyalty funds.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2342 to update the Issue, Action, and Service Procedure. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns including but not limited to: Sirius audio not functioning properly after a key cycle with active subscription Presets not responding or indicating properly Intermittent audio echo/robotic voice heard during a Bluetooth phone call Wi-Fi connection message pop-up every key cycle Frozen unresponsive touchscreen Solid blue screen when moving forward at speeds above 16 km/h (10 mph) (2019 vehicles only) Rear parking aid camera remains on the screen at speeds below 16 km/h (10 mph) (2019 vehicles only) Inoperative infotainment applications Poor/no AppLink function Apple CarPlay not launching on connection or a black screen when connected Voice prompts that skip or have short pauses while directions are being provided
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine PCM Reprogram Due to Engine Shudder; Owner Letter sent
Source components: ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 F-150 vehicles built on or before 1-Apr-2020 equipped with a 3.0L diesel engine, 2017-2019 F-Super Duty vehicles built on or before 30-Oct-2019 equipped with a 6.7L engine and 2016-2019 F-650/F-750 vehicles built on or before 30-Oct-2019 equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P21DD, P20BA. P20B9, P204C, P208A, P208B, P208C, P203B, P205B, P21CD and/or U02A2 in the powertrain control module (PCM). This may be due to water intrusion within connectors C3613 and/or C4851/C3610 on the reductant harness going to the reductant pump/heater assembly and the reductant level sensor/quality module. To correct the condition, follow the Service Procedure steps to replace the reductant tank harness, the reductant pump/heater assembly and/or the reductant tank.
Source components: ELECTRICAL SYSTEM · ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang and 2019-2021 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware wear-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 Super Duty vehicles equipped with a 6.7L engine built on or after 13-May-2017, 2015-2019 Transit vehicles equipped with a 3.2L engine and 2018-2020 F-150 vehicles equipped with a 3.0L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2002 stored in the powertrain control module (PCM). This may be due to a crack in the diesel particulate filter (DPF) substrate. To correct the condition, follow the Service Procedure steps to replace the DPF and then reprogram the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Expedition/Navigator, 2015-2020 F150 and 2017-2020 F-Super Duty vehicles equipped with power running boards (PRB) may exhibit a condition where the PRBs are disabled, changing the feature menu setting from Auto to Off mode in the instrumental panel cluster (IPC), DTC U3003:16 stored in the running board control module (RBM) and with or without an illuminated charging system indicator lamp. This may be due to a low battery voltage event or a fully discharged battery. To correct this condition, inspect the charging system and correct the low battery voltage event. Refer to Workshop Manual (WSM), Section 501-08 > Diagnosis and Testing. Configure the PRB system mode from Off to Auto mode in the Advance Settings of the IPC. Refer to the Owner's Manual > Power Running Boards.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine Cam Phaser Replacement; Owner letters are scheduled to mail during the week of September 27, 2021⢠Submitting Claims with Ford Protect for Balance Remaining: Added instruction on how to claim the customer paid portion of the FSA with Ford Protect.⢠Submitting Claims with Customer Loyalty Program for Balance Remaining: Added instruction on how to claim the customer paid portion of the FSA using CLP Funds. This program extends the warranty coverage of the engine cam phasers until January 1, 2023 provided the Repair Order (RO) date of Powertrain Control Module reflash under Customer Satisfaction Program 21B10 occurs on or before February 28, 2022
Source components: ELECTRICAL SYSTEM:ADAS:CONTROL MODULE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine PCM Reprogram Due to Engine Shudder ;In a very low percentage of the affected vehicles, an engine shudder may develop after receiving the PCM update provided in program 21B10. For peace of mind, Ford is providing a no-cost, one-time repair for customers who receive the PCM update under program 21B10 to revert the PCM calibration back to its original state before program 21B10.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine Powertrain Control Module Reprogram for Cam Phaser Rattle
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM) · POWER TRAIN:MANUAL TRANSMISSION:INTERNAL:DOGS/SYNCHROS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 F-150, 2017-2021 F-Super Duty and 2018-2021 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit a binding/sticking, glass stuck open or closed, noisy operation including chatter, rattling, or grinding. This may be due to the glass panel brackets cracking and/or breaking apart. The glass panel brackets are serviceable separately from the frame assembly and require the roof opening panel glass to be moved to the vent position. To correct the condition, follow the Service Procedure to replace the roof opening panel glass brackets
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2021 Ford and Lincoln vehicles equipped with 3.3L, 3.5L EcoBoost, or 5.0L engines may exhibit stalling, lack of power, low fuel rail pressure and/or DTCs P0087 or P008A after a repair was made that required the removal of the fuel line that connects the high-pressure fuel pump to the port injection rail, such as injector replacements or base engine repairs. This line must be installed in the correct orientation as it has an internal one-way check valve. To determine if the fuel line has been installed improperly, look at the position of the Oetiker clamp (stainless band clamped around the black fuel line). The clamp holds the one-way check valve in place and should be located closest to the end connected to the port injection rail. If the clamp is not closest to the port injection rail, remove and reinstall the line in the proper orientation.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150, 2017-2020 Super Duty and 2018-2020 Expedition/Navigator vehicles may exhibit poor air conditioning (A/C) performance, loss of airflow and/or engine cooling fans running continuously from high A/C pressures. This concern may be from the evaporator freezing up due to the evaporator temperature sensor being biased. To correct the condition, follow the Service Procedure steps to replace the evaporator temperature sensor.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
Source components: SERVICE BRAKES, ELECTRIC:SOFTWARE/PROGRAMMING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 F-150 vehicles equipped with a 3.5L PowerBoost, 3.5L EcoBoost or 2.7L EcoBoost engine and some 2018-2021 Expedition and Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04F0 and/or P144C stored in the powertrain control module (PCM). This may be due to loose or partially connected evaporative emissions (EVAP) vapor lines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2017-2020 F-150 vehicles equipped with a 3.5L engine and a 10R80 transmission may experience an error message while performing Transmission Characterization/Solenoid IDN with IDS v122.05 or v122.06 stating "Unable To Communicate With The Module". This is due to an issue with the Transmission Characterization/Solenoid IDN tool in IDS v122.05 and v122.06. To resolve the issue, uninstall IDS from the computer. Then, run the IDS clean up utility tool, located on PTS > Rotunda Tab > Diagnostic Tool Support > IDS Support > IDS troubleshooting guide. Next, install IDS v123.01 (123_FULL) and retry the Transmission Characterization/Solenoid IDN tool using IDS level v123.01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2021 Ford and Lincoln vehicle customers may receive a message in their FordPass or Lincoln Way App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.
Source components: POWER TRAIN:MANUAL TRANSMISSION:INTERNAL:DOGS/SYNCHROS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2017-2020 F-150 vehicles equipped with a 3.5L engine and a 10R80 transmission may experience an error message while performing Transmission Characterization/Solenoid IDN with IDS v122.05 stating "Unable To Communicate With The Module". A temporary workaround to complete programming is as follows: Uninstall IDS from the computer. Then, run the IDS clean up utility tool, located on PTS > Rotunda Tab > Diagnostic Tool Support > IDS Support > IDS troubleshooting guide. Next, Install IDS v122.01 (122_FULL) and retry the Transmission Characterization/Solenoid IDN using IDS level 122.01. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time or as a knocking noise when the engine is idling after it is warmed up. These concerns should be addressed by the updated calibration provided in FSA 21B10. However, for peace of mind, Ford is providing an extended warranty for customers who receive the PCM update under program 21B10 prior to December 21, 2021 and continue to experience cam phaser noise after receiving that PCM update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
It may be possible that an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after your vehicle was turned off for an extended period of time, or as a knocking noise when the engine is idling after it is warmed up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time or as a knocking noise when the engine is idling after it is warmed up. These concerns should be addressed by the updated calibration provided in FSA 21B10. However, for peace of mind, Ford is providing an extended warranty for customers who receive the PCM update under program 21B10 prior to December 31, 2021 and continue to experience cam phaser noise after receiving that PCM update, A cam phaser that has developed an undesirable noise does not affect the vehicle safety, performance, or emissions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time, or as a knocking noise when the engine is idling after it is warmed up. A cam phaser that has developed an undesirable noise does not affect the vehicle safety, performance, or emissions.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2021 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0096 in the powertrain control module (PCM). This may be due to an issue with the manifold absolute pressure (MAP) sensor. To correct the condition, follow the Service Procedure to replace the MAP sensor.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 F-150 and F-Super Duty vehicles may exhibit one or more power door locks inoperative. This concern may be due to a power door lock actuator. To correct the condition, follow the Service Procedure steps to replace the affected actuator.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2144 to update the vehicle model years affected and the Part List. Some 2015-2020 F-150 and 2017-2021 F-Super Duty vehicles may exhibit a lack of heat or cooling from the cabin vents when the climate control settings are adjusted between hot and cold. This may be due to a stuck/binding temperature door within the climate control housing or binding/inoperative temperature door actuator. Diagnostic trouble code (DTC) B1081:07 may be present in the front controls interface module (FCIM). To correct the condition, follow the Service Procedure steps to remove the climate control housing and replace the temperature door actuator(s) and/or lubricate the temperature blend door bearing surface.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2021 Ford and Lincoln vehicles may exhibit an intermittent audio echo/robotic voice heard during a bluetooth phone call by the person that is not in the vehicle. Using Apple CarPlay and Android Auto instead of Bluetooth can help alleviate the concern. Also turning on, then off, the privacy setting in the SYNC touchscreen can temporarily alleviate the concern. Engineering is currently investigating this concern and will be releasing a service fix in early July 2021. Let the customer know they can continue to drive the vehicle and schedule service appointments for customers once the repair becomes available. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) and/or Engine Coolant Over Temperature warning with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0128, P0217, P0330, P1026, and/or P1299. This condition may be caused by an intermittent drop in the engine coolant temperature (ECT) voltage. To correct this condition, replace the heater hose with the new relocated ECT and install a jumper harness.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ford Motor Company has determined certain 2020 Model Year Ford F-150, F-Super Duty and Explorer vehicles with a Ford factory-installed backup camera fail to conform to Federal Motor Vehicle Safety Standard number 111 - Rear Visibility. Contact your local Ford dealer to schedule a service date to perform the recall. Refer to the included communication from Ford for additional information. Altec is not able to complete this repair. All work must be completed by an authorized Ford dealer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2021 Ford and Lincoln vehicle owners may experience a condition of missing Authorization, Command and Control, Battery Charging Details or Phone-as-a-Key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, Utilize the FordPass Guides or Lincoln Way Concierge teams.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150 XL/XLT vehicles may exhibit warping/separation of the instrument panel at the defrost vents. To correct the condition, follow the Service Procedure to replace the instrument panel upper section.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2021 vehicles equipped with a diesel engine may have engine oil in the exhaust after turbocharger replacement for various reasons. To correct the condition, remove the exhaust and stand the exhaust up with the turbocharger inlet side facing down using a suitable drain pan. Allow the exhaust to drain for at least 24 hours and reinstall. Do not perform a manual exhaust regeneration.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 Ford and Lincoln vehicles may not be able to perform remote commands via the FordPass/LincolnWay App due to an erroneous deep sleep message. If the vehicle has been driven within 14 days and the battery state of charge is above 9.5 volts when the deep sleep message set, this is an erroneous message. Starting and running the vehicle will clear the message and allow the remote commands to function again. Inform customers that engineering is currently working on a solution for this condition that will be released via an over the air (OTA) update that is expected in June 2021. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM) will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 F-150 and 2017-2021 F-Super Duty vehicles may exhibit a lack of heat or cooling from the cabin vents when the climate control settings are adjusted between hot and cold. This may be due to a stuck/binding temperature door within the climate control housing or binding/inoperative temperature door actuator. Diagnostic trouble code (DTC) B1081:07 may be present in the front controls interface module (FCIM). To correct the condition, follow the Service Procedure steps to remove the climate control housing and replace the temperature door actuator(s) and/or lubricate the temperature blend door bearing surface.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2021 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150F (65àâÂÂC) or higher and engine speed is at idle up to approximately 1700 RPMs. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 F-150 2018-2020 Expedition/Navigator vehicles built on or before 31-Oct-2019 and equipped with a 3.5L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure steps to replace the VCT units.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2017-2020 Model Year F-150 Equipped with a 3.5L GTDI Engine Powertrain Control Module Reprogram for Cam Phaser Rattle Reports of Transmission Shudder after PCM Reprogram: Dealers are instructed to stop performing this field service action until further notice. This shudder is under investigation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 F-150/F-Super Duty/Expedition/Navigator and 2020 Explorer/Aviator vehicles may exhibit a 'Trailer Connected' or 'Trailer Disconnected' message in the vehicle's message center with no trailer attached to the vehicle. To address this condition, reprogram the trailer module (TRM) using the appropriate Ford diagnostic scan tool. For claiming use causal part 19H332 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2017-2020 Model Year F-150 Equipped with a 3.5L GTDI Engine Powertrain Control Module Reprogram for Cam Phaser Rattle In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time, or as a knocking noise when the engine is idling after it is warmed up. A cam phaser that has developed an undesirable noise does not affect the vehicle safety, performance, or emissions
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2017-2020 Model Year F-150 Equipped with a 3.5L GTDI Engine Cam Phaser Replacement In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time or as a knocking noise when the engine is idling after it is warmed up. A cam phaser that has developed an undesirable noise does not affect the vehicle safety, performance, or emissions
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with DTC P025A And/Or DTC U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs or loose/corroded grounds. Inspect FPCM connector, applicable grounds(F-150- G401, Expedition/Navigator- G403, Transit- G401, 2018-2019 Explorer G302, 2020-2021 Explorer/Aviator- G407) and confirm FPCM connector (F-150- C4336, Expedition/Navigator- C433, Transit- C433, 2018-2019 Explorer C3239, 2020-2021 Explorer/Aviator- C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 F-150 vehicles equipped with a 2.7L EcoBoost engine built on or before 04-Jul-2020 may experience an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2196, P2198, P2BF0, P2BF2, P2BF1, P2BF3, P2BEC, P2CEE, P2BED, P130D and/or P2BEF stored in the powertrain control module (PCM). There may also be an intermittent brief deceleration when cruise control is enabled. This may be due to software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 F-150 vehicles equipped with a 5.0L engine may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0021 and/or P0022 stored in the powertrain control module (PCM). The vehicle may also exhibit noise near the front of the valve covers from the intake variable camshaft timing (VCT) phasers. To resolve this condition, verify the engine oil is at the proper level. Adjust the engine oil level as necessary. If the condition persists, replace only the VCT solenoid(s) associated with the DTCs present. If the condition persists after VCT solenoid replacement, continue with normal Powertrain Controls and Emissions Diagnosis (PC/ED) Manual diagnostics and/or follow engine NVH diagnostics in Workshop Manual (WSM), Section 303-00. For claiming, use causal part 6M280 and applicable labor operations in the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code on the PTS website (Detailed Vehicle Specifications). If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early March. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early March. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2021 F-Super Duty and 2016-2021 F650-750 with 6.7L diesel engines, 2015-2019 Transit with 3.2L diesel engines and 2018-2021 F-150 with 3.0L diesel engines may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P206C in the powertrain control module (PCM). Review of repair data supports that P206C is often the result of incorrect diesel exhaust fluid (DEF) concentration. Per Powertrain Control/Emissions Diagnosis (PC/ED) Pinpoint Test (PPT) RJ, a DEF concentration reading below 28% will set P206C and cause vehicle derate. If low concentration is suspected, drain fluid and replace with known good DEF before replacing any parts. Low concentration of DEF is not a warrantable condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 F-150, 2016-2018 MKX, 2019-2021 Nautilus, 2015-2021 Edge, 2017-2019 Fusion, 2017-2020 MKZ And 2017-2020 Continental vehicles equipped with a 2.7L/3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual > Maintenance > Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 F-150/Navigator vehicles equipped with a 3.5L EcoBoost High-Output engine and built on or before 11-Sept-2020 may exhibit excessive oil consumption with no visible oil leaks with or without diagnostic trouble code (DTC) P0365 and/or P0369. To correct the condition, follow the Service Procedure steps to reprogram the powertrain control module (PCM) and if necessary, replace the engine valve covers.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150 and 2018-2020 Expedition/Navigator vehicles equipped with a 3.5L/2.7L EcoBoost engine and four-wheel drive (4WD) may exhibit an intermittent grinding type noise while driving in two-wheel drive (2WD), most commonly on acceleration. This noise could appear to be turbocharger related. After engineering analysis of returned turbochargers that have been replaced for this condition, no concerns were identified with the turbochargers. The grinding type noise may be related to the 4WD system integrated wheel ends (IWE). To aid in diagnosis, shift the vehicle to 4WD and attempt to verify the condition. If the grinding noise no longer occurs with the vehicle in 4WD a IWE vacuum system and/or mechanical fault may be present.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2011-2020 F-150/Mustang vehicles equipped with a 5.0L engine when installing a replacement secondary timing chain tensioner (6K254) or secondary timing chain guide (6K297), it is necessary to replace both components as a pair, using the latest level parts. Make sure to use secondary timing chain tensioner part number ML3Z-6K254-A and secondary timing chain guide part number ML3Z-6K297-A.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2020 Model Year Multiple Vehicle Lines Front View and Center High Mount Stop Lamp Camera Improper Function In some of the affected vehicles, insufficient electrical conductivity within the Printed Circuit Board (PCB) internal to the camera may lead to intermittent front view or Center High Mount Stop Lamp (CHMSL) camera operation. This could result in a blank or distorted image from the front of the vehicle or of the truck bed Dealers are to replace the front view camera or the CHMSL camera following the dealer bulletin technical information. This service must be performed on all affected vehicles at no charge to the vehicle owner.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:ADAS:HUD:CAMERA/SENSOR · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 F-150 Lariat vehicles equipped with the snow plow prep package may exhibit the snow plow button illuminating when you press the start/stop deactivation button, and the start/stop deactivation indicator illuminating when you press the snow plow button. Both features otherwise function correctly, and the correct messages illuminate in the message center when pressing either button. This may be due to incorrect switch circuitry. To correct the condition, follow the Service Procedure steps to swap circuit pin locations.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14H092 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code. If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 MKZ, 2019-2020 EcoSport/Mustang/Continental/Fusion/F-150/Transit Connect/Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 vehicles equipped with TOD transfer cases may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure steps to remove and cap the vacuum supply line.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2019-2020 F-150 vehicles equipped with four-wheel drive (4WD) have a revised transfer case control module (TCCM) strategy that will affect integrated wheel end (IWE) operation after initial start-up. The TCCM will not energize the solenoid to supply vacuum to the IWEs after the initial key cycle and a driven gear is selected. The IWEs will remain engaged for 0.8 km (0.5 mi) when the temperature is above 0 deg C (32 deg F) and 3 km (2 mi) when below 0 deg C (32 deg F). The strategy changes were implemented to improve vacuum supply management and axle warm up in cold temperatures. The engine must run for a minimum of 5 minutes to build sufficient vacuum before performing any vacuum related testing. Refer to the Workshop Manual (WSM) Section, 307-08A > Four-Wheel Drive Systems > System Operation and Component Description for additional information.
Source components: POWER TRAIN · POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 F-150/F-Super Duty vehicles built on 18-May-2020 and through 30-Jun-2020 may exhibit a concern where the right rear door lock is inoperative but the manual lock rod works. This may be due to stack up tolerances of the handle, cable and latch. To correct the condition, follow the Service Procedure to remove the cable barrel sleeve.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150/Mustang, 2016-2020 Edge, 2016-2018 MKX and 2019-2020 Nautilus vehicles built on or before 18-Jan-2020 may exhibit a mirror click and/or ratcheting noise when using memory functions or easy entry/exit function. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM with the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14B291 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 F-150 vehicles equipped with a 3.5L EcoBoost engine, 2018-2020 F-150 vehicles equipped with a 2.7L EcoBoost or 5.0L engine, 2019-2020 F-150 vehicles equipped with a 3.0L engine, may exhibit a high pitched squeal or whistle type noise from the engine compartment after the engine is shut off. This condition may be due to the air conditioning (A/C) low side system pressure exceeding the high side pressure resulting in equalization of A/C system pressures through the A/C compressor. This noise is not detrimental to system operation or durability. Submit a Global Concern Report, and let the customer know they can continue to drive the vehicle. Set a follow-up appointment for June 2021 when repairs are expected to become available. Follow up with the customer to confirm the appointment once OASIS is updated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2020 Model Year Transit vehicles with 3.5L engines and F-150 / Police Interceptor Utility vehicles with 3.3L engines - Cylinder Head Replacement
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 F-150 2018-2020 Expedition/Navigator vehicles built on or before 31-Oct-2019 and equipped with a 3.5L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure steps to replace the VCT units and update the powertrain control module (PCM) calibration with revised VCT parameters.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 MKZ, 2019-2020 Mustang/Continental/Fusion/F-150/Transit Connect/ Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/ Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150 except Raptor, 2017-2020 F-Super Duty, 2018-2020 Expedition vehicles equipped with a front camera washer may exhibit a washer fluid leak at the front camera washer jet when not in use. This may be due to the rubber seal internal to the jet. To correct the condition, follow the Service Procedure to replace the washer jet.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 20-2162 to update the Labor Operations descriptions. Some 2018-2020 F-150 Raptor and 2019-2020 F-150 Limited vehicles equipped with a 3.5L EcoBoost High-Output engine may exhibit excessive oil consumption with no visible oil leaks with or without diagnostic trouble code (DTC) P0365 and/or P0369. To correct the condition, follow the Service Procedure steps to reprogram the powertrain control module (PCM), and for vehicles built on or before 1-Apr-2019 that have not previously had both valve covers replaced perform an oil consumption test.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 F-150 vehicles equipped with a 3.3L Duratec engine and built on or before 18-Aug-2020 may exhibit a lack of heat intermittently. This may be due to the powertrain control module (PCM) not running the auxiliary coolant pump during stop-start situations. To correct the condition, follow the Service Procedure to reprogram the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 20-2083 to update the vehicle model years affected. Some 2019-2020 Ranger and 2020 F-150/Mustang vehicles equipped with a 10R80 transmission and built on 21-Oct-2019 and through 16-Dec-2019 may exhibit a high-pitched whine coming from the transmission at low speeds during light acceleration or coasting. This may be due to the outer output shaft bearing. To correct the condition, follow the Service Procedure steps to replace the transmission inner output shaft bearing, fluid passage sleeve and outer output shaft bearing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150, 2016-2018 MKX, 2019-2020 Nautilus, 2015-2020 Edge, 2017-2019 Fusion, 2017-2020 MKZ And 2017-2020 Continental vehicles equipped with a 2.7L/3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual > Maintenance > Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
Source components: ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 Transit vehicles equipped with a 3.2L engine, 2018-2020 F-150 vehicles equipped with a 3.0L engine, 2017-2020 Super Duty vehicles equipped with a 6.7L engine built on or after 13-May-2017 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2002 stored in the powertrain control module (PCM). This may be due to a crack in the diesel particulate filter (DPF) substrate. To correct the condition, follow the Service Procedure steps to replace the DPF.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 F-150 vehicles equipped with a 5.0L engine may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0021 and/or P0022 stored in the powertrain control module (PCM). In addition to the DTCs, the vehicle may also exhibit noise near the front of the valve covers from the intake variable camshaft timing (VCT) phasers. To resolve this condition, replace only the VCT solenoid(s) associated with the DTCs present. If the condition persists after VCT solenoid replacement, continue with normal Powertrain Controls and Emissions Diagnosis (PC/ED) Manual diagnostics for any DTCs, and/or follow engine NVH diagnostics in Workshop Manual (WSM), Section 303-00. For claiming, use causal part 6M280 and applicable labor operations in the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 MKZ, 2019-2020 Mustang/Continental/Fusion/F-150/Transit Connect/ Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/ Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2020 F-Super Duty, 2015-2019 Transit, 2016-2021 F-650/F-750 and 2018-2020 F-150 vehicles equipped with a 6.7L, 3.2L or 3.0L engine may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P207F, P20EE, P229F, P2201 and/or P24AE. This may be a result of using aftermarket cleaning liquids or tools for the exhaust gas recirculation (EGR) cooler or intake. Ford does not recommend the cleaning of diesel intakes or EGR coolers using any aftermarket tool that injects a cleaning foam or liquid substance into the EGR cooler or intake. Using these types of fluids can result in sodium poisoning of the NOx and particulate matter (PM) sensors resulting in degraded operation and permanent damage to the after treatment system. Use of these cleaning tools may void the emissions warranty of the hot end after treatment exhaust system and the attached emissions sensors.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · FUEL SYSTEM, DIESEL.