The manufacturer’s record · Page 1 of 4
Original record summaries, dates and identifiers for this model-year. Records 1–100 of 343, ordered newest first. Dated records on this page: Jul 15, 2021–Jul 9, 2026.
Back to 2017 Ford F-150 problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 11035463
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Program 26N04 Certain 2015-2017 Model Year F-150 Vehicles Equipped with a 6R80 Transmission Transmission Molded Leadframe Replacement
Source components: POWER TRAIN.
Source record 11035463 at NHTSANHTSA communication ID: 11031792
NHTSA source summary · Original PDF not reviewed by Recallfolio
Harvest Program 25H05 – Supplement #1 Certain 2011-2021 Model Year Vehicles Software Verification Harvest Program
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
Source record 11031792 at NHTSANHTSA communication ID: 11030282
NHTSA source summary · Original PDF not reviewed by Recallfolio
Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
Source components: BACK OVER PREVENTION: REARVIEW SYSTEM BRAKING · BACK OVER PREVENTION: WARNINGS · LANE DEPARTURE: BLIND SPOT DETECTION · UNKNOWN OR OTHER.
Source record 11030282 at NHTSANHTSA communication ID: 11029052
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
Source record 11029052 at NHTSANHTSA communication ID: 11029081
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 20172026 vehicles equipped with a 10R transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.
Source components: POWER TRAIN.
Source record 11029081 at NHTSANHTSA communication ID: 11026928
NHTSA source summary · Original PDF not reviewed by Recallfolio
Special Field Action 25L02 Certain 2017-2024 Model Year California Emissions-Certified Vehicles Transmission Control Assembly Reimbursement
Source components: UNKNOWN OR OTHER.
Source record 11026928 at NHTSANHTSA communication ID: 11025837
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.
Source components: ELECTRICAL SYSTEM.
Source record 11025837 at NHTSANHTSA communication ID: 11026013
NHTSA source summary · Original PDF not reviewed by Recallfolio
This is a proactive investigation program by Ford Motor Company to inspect a limited number of affected vehicles that are customer-owned. Ford is voluntarily conducting this program to evaluate the software currently installed on one or more electronic modules in the affected vehicles.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
Source record 11026013 at NHTSANHTSA communication ID: 11025611
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
Source record 11025611 at NHTSANHTSA communication ID: 11024874
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes TSB 25-2301. Reason for update: update the Part List Description. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh engagement * Delayed engagement * Harsh shift * Delayed shift * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to axial movement of the CDF clutch cylinder (7H351) sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as necessary as needed to ensure proper function. Add a new line to the repair order to document any additional
Source components: POWER TRAIN.
Source record 11024874 at NHTSANHTSA communication ID: 11023858
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain Model Year Multiple Vehicles Ford Pass/Lincoln Way Connectivity Concerns
Source components: UNKNOWN OR OTHER.
Source record 11023858 at NHTSANHTSA communication ID: 11021972
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes TSB 25-2126. Reason for update: update the Part List and Service Procedure. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh engagement * Delayed engagement * Harsh shift * Delayed shift * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to axial movement of the CDF clutch cylinder (7H351) sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as necessary as needed to ensure proper function. Add a new line to the repair order to documen
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
Source record 11021972 at NHTSANHTSA communication ID: 11016931
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes TSB 25-2018. Reason for update: update the Part List and Service Procedure. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh engagement * Delayed engagement * Harsh shift * Delayed shift * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM).
Source components: UNKNOWN OR OTHER.
Source record 11016931 at NHTSANHTSA communication ID: 11015680
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2020 F-150 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0630 stored in the powertrain control module (PCM). This may be due to aftermarket modifications to the body control module (BCM), such as changes to the tire size or axle ratio in the BCM.
Source components: UNKNOWN OR OTHER.
Source record 11015680 at NHTSANHTSA communication ID: 11013132
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2025 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving.
Source components: UNKNOWN OR OTHER.
Source record 11013132 at NHTSANHTSA communication ID: 11010950
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs. Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs.
Source components: UNKNOWN OR OTHER.
Source record 11010950 at NHTSANHTSA communication ID: 11008948
NHTSA source summary · Original PDF not reviewed by Recallfolio
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
Source components: UNKNOWN OR OTHER.
Source record 11008948 at NHTSANHTSA communication ID: 11006476
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 F-150 and 2017-2019 F-Super Duty vehicles may not successfully complete the Transmission Characterization/Solenoid IDN procedure using the Integrated Diagnostic System (IDS) scan tool. This may be due to the IDS not being at the latest software level
Source components: UNKNOWN OR OTHER.
Source record 11006476 at NHTSANHTSA communication ID: 11005305
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2219 to update the Parts List and Service Procedure to clarify applicable steps by vehicle application. Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 (non-Raptor) vehicles equipped with 4WD may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure to remove and cap the vacuum supply line or to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.
Source components: WHEELS.
Source record 11005305 at NHTSANHTSA communication ID: 11001174
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2175 to update the TSB Service Procedure. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.
Source components: UNKNOWN OR OTHER.
Source record 11001174 at NHTSANHTSA communication ID: 11000297
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.
Source components: POWER TRAIN.
Source record 11000297 at NHTSANHTSA communication ID: 10254138
NHTSA source summary · Original PDF not reviewed by Recallfolio
All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
Source components: EQUIPMENT.
Source record 10254138 at NHTSANHTSA communication ID: 10252674
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2046 to update the Service Procedure LTIS statement. Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang, 2019-2023 Ranger vehicles equipped with a 10R80 transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) that are stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.
Source components: POWER TRAIN.
Source record 10252674 at NHTSANHTSA communication ID: 10252672
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2330 to update the Parts List. Some 2015-2017 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit an oil leak from the oil pan RTV seal. This may be due to various concerns with the oil pan. To correct the condition, follow the Service Procedure to replace the oil pan with the later style oil pan.
Source components: ENGINE AND ENGINE COOLING.
Source record 10252672 at NHTSANHTSA communication ID: 10251952
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
Source components: ENGINE AND ENGINE COOLING.
Source record 10251952 at NHTSANHTSA communication ID: 10251951
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2024 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a tick tap and/or typewriter ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150°F (65°C) or higher and engine speed is at idle up to approximately 1700 RPM. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise tick rate can be faster or slower and is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted. This information along with an example audio clip has been added to the WSM Section 303-00 Engine System General Information > Diagnosis and Testing > Engine > PPT F > Step F2.
Source components: ENGINE AND ENGINE COOLING.
Source record 10251951 at NHTSANHTSA communication ID: 10251934
NHTSA source summary · Original PDF not reviewed by Recallfolio
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
Source components: POWER TRAIN.
Source record 10251934 at NHTSANHTSA communication ID: 10251469
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2350 to update the Issue statement and the Service Procedure. Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang, 2019-2023 Ranger vehicles equipped with a 10R80 transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
Source record 10251469 at NHTSANHTSA communication ID: 10251454
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2083 to update the Service Procedure and the Part List. Some 2015-2017 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit an oil leak from the oil pan RTV seal. This may be due to various concerns with the oil pan. To correct the condition, follow the Service Procedure to replace the oil pan with the later style oil pan.
Source components: ENGINE AND ENGINE COOLING.
Source record 10251454 at NHTSANHTSA communication ID: 10245418
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang, 2019-2023 Ranger vehicles equipped with a 10R80 transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE.
Source record 10245418 at NHTSANHTSA communication ID: 10244827
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 F-150 and 2016-2017 Expedition/Navigator vehicles may require pressure bleeding of the brake system. The brake system pressure bleeding procedure in the Workshop Manual (WSM), Section 206-00, has been updated to add a warning to not apply the brake pedal or master cylinder damage may occur.
Source components: EQUIPMENT · SERVICE BRAKES.
Source record 10244827 at NHTSANHTSA communication ID: 10243652
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-Super Duty and 2015-2020 F-150/Mustang vehicles may require replacement of the powertrain control module (PCM) for various reasons. While performing a programmable module installation (PMI) using the Integrated Diagnostic Service (IDS) scan tool, an error message may state: Configuration Failed, Would You Like To Retry? This may be due to improper module replacement steps. Make sure that the original module is installed in the vehicle, delete the vehicle session, then start a new vehicle session. Once the session starts, run the PCM PMI and install the new PCM only when the scan tool instructs. Finish the PMI by following the prompts given by IDS. If the original PCM is not available, it is possible to configure the module by running as-built programming on the PCM. When IDS asks to obtain part numbers or configuration data, select configuration data.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10243652 at NHTSANHTSA communication ID: 10243648
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2023 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability. Use the Report a Vehicle Concern link at the bottom of OASIS to submit a report if there is a customer concern of whine noise describing operating conditions and noise severity.
Source components: POWER TRAIN.
Source record 10243648 at NHTSANHTSA communication ID: 10243609
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.
Source components: EQUIPMENT.
Source record 10243609 at NHTSANHTSA communication ID: 10241447
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2428 and 23-2176 to update the Issue, Action and Service Procedure. Some 2017-2023 F-150, 2018-2023 Expedition/Navigator/Mustang, 2019-2023 Ranger, 2020-2023 Explorer/Aviator/Transit and 2021-2023 Bronco vehicles equipped with a 10R60/10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.
Source components: POWER TRAIN.
Source record 10241447 at NHTSANHTSA communication ID: 10241627
NHTSA source summary · Original PDF not reviewed by Recallfolio
In various 2017-2023 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.
Source components: ELECTRICAL SYSTEM.
Source record 10241627 at NHTSANHTSA communication ID: 10240719
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some F-Super Duty and F-150 vehicles equipped with trailer tow mirror may exhibit various exterior rear view mirror functional concerns that require replacement after diagnosis. To properly determine if the defect is warrantable, cleaning and close inspection of the affected mirror may be required. To aid in proper warranty determination, the Rear-View Mirror Analysis general service bulletin (GSB) has been updated with a detailed cleaning procedure that should be followed prior to any inspection. New labor operations (17682ZZ or 17682ZZT) have been created that covers the cleaning and inspection process and may be used even if condition of failure is non-warrantable. Ford has inspected numerous returned parts and determined many cases are caused by damage which is unwarrantable and may be subject to chargeback. Refer to the latest version of the GSB on OASIS.
Source components: EQUIPMENT · VISIBILITY:REARVIEW MIRRORS/DEVICES.
Source record 10240719 at NHTSANHTSA communication ID: 10240743
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10240743 at NHTSANHTSA communication ID: 10237786
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB 22-2428 is missing some labor operations. For any missing labor operations, claim available new model labor operations or m-time. Refer to this article on the repair order. When replacing the CDF cylinder, the current TSB does not require a complete transmission overhaul or cooler and converter flushing. Ford is currently reviewing the TSB. Monitor OASIS for updates.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN · UNKNOWN OR OTHER.
Source record 10237786 at NHTSANHTSA communication ID: 10236680
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2023 F-150, 2018-2023 Expedition/Navigator/Mustang, 2019-2023 Ranger, 2020-2023 Explorer/Aviator/Transit and 2021-2023 Bronco vehicles equipped with a 10R60 transmission and built on or before 23-Dec-2022 or with a 18R80/10R80MHT transmission and built on or before 15-Aug-2022 may exhibit a harsh/delayed engagement and/or harsh/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the PCM or TCM, the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.
Source components: POWER TRAIN.
Source record 10236680 at NHTSANHTSA communication ID: 10236683
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2123 to update the Issue statement. Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang and 2019-2023 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the keep alive memory in the PCM/TCM or the transmission main control valve body. To correct the condition, follow the Service Procedure to overhaul the main control valve body and/or perform an adaptive learning drive cycle.
Source components: POWER TRAIN.
Source record 10236683 at NHTSANHTSA communication ID: 10236037
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 F-150 and 2018-2020 Expedition/Navigator vehicles built on or before 30-Nov-2019 and equipped with a 3.5L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. Some vehicles may also exhibit an intermittent condition with no auto restart during auto-start-stop operation with or without diagnostic trouble code (DTC) P164C present in the powertrain control module (PCM). This may be due to a worn variable camshaft timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
Source record 10236037 at NHTSANHTSA communication ID: 10234593
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150 and 2017-2022 F-Super Duty vehicles may exhibit a lack of heat or cooling from the cabin vents when the climate control settings are adjusted between hot and cold. This may be due to a stuck/binding temperature door within the climate control housing or binding/inoperative temperature door actuator. Diagnostic trouble code (DTC) B1081:07 may be present in the front controls interface module (FCIM) or heating ventilation and air conditioning (HVAC) module. To correct the condition, follow the Service Procedure to remove the climate control housing and replace the temperature door cam(s), lubricate the temperature blend door bearing surface, and apply flock tape to actuator to seal out debris.
Source components: EQUIPMENT.
Source record 10234593 at NHTSANHTSA communication ID: 10234596
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang and 2019-2023 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware break-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
Source record 10234596 at NHTSANHTSA communication ID: 10235153
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
Source components: STRUCTURE.
Source record 10235153 at NHTSANHTSA communication ID: 10233745
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 F-150 vehicles built on or before 01-Feb-2021, 2017-2020 F-150 vehicles equipped with a 3.5L EcoBoost engine, 2018-2020 F-150 vehicles equipped with a 2.7L EcoBoost or 5.0L engine, 2019-2020 F-150 vehicles equipped with a 3.0L diesel engine may exhibit a high pitched squeal or whistle type noise from the engine compartment after the engine is shut off. This condition may be due to the air conditioning (A/C) low side system pressure exceeding the high side pressure resulting in equalization of A/C system pressures through the A/C compressor. An updated A/C compressor has been released to resolve this concern. For claiming, use causal part 19703 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual.
Source components: VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM.
Source record 10233745 at NHTSANHTSA communication ID: 10233594
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit an oil leak from the oil pan RTV seal. This may be due to various concerns with the oil pan. To correct the condition, follow the Service Procedure to replace the oil pan with the later style oil pan.
Source components: ENGINE AND ENGINE COOLING.
Source record 10233594 at NHTSANHTSA communication ID: 10233695
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2023 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability.
Source components: POWER TRAIN.
Source record 10233695 at NHTSANHTSA communication ID: 10232485
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with a 2.7L, 3.0L,3.5L or 5.0L engine may require replacement of the long block engine assembly. New service kits have been released which include all the one-time-use components required in the service procedure for removal and replacement of the long block engine assembly. Refer to the Ford Electronic Parts Catalog (ECAT) for long block service kit part number by application.
Source components: EQUIPMENT.
Source record 10232485 at NHTSANHTSA communication ID: 10230798
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150 vehicles equipped with a 2.7L, 3.5L or 5.0L engine may require replacement of the long block engine assembly. New service kits have been released which include all the one-time-use components required in the service procedure for removal and replacement of the long block engine assembly. Refer to the Ford Electronic Parts Catalog (ECAT) for long block service kit part number by application.
Source components: ENGINE AND ENGINE COOLING.
Source record 10230798 at NHTSANHTSA communication ID: 10228881
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.
Source components: EQUIPMENT · VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR.
Source record 10228881 at NHTSANHTSA communication ID: 10228880
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2023 F-150, 2017-2022 F-Super Duty, and 2019-2023 Ranger vehicles may exhibit dust ingress into the cabin through the doors or air extractors. This may be due to the climate control system being in recirculation mode as a result of the recirculation button being on or automatic strategies for heating/cooling efficiency. To minimize dust ingress when driving in off-road or secondary road conditions, make sure that all doors and windows are fully closed and the climate control system is switched to defrost on and the instrument panel and footwell air vents are switched to off. Temperature and fan settings may be adjusted as desired. Alternatively, max defrost can be activated which will adjust all settings automatically. Operating in defrost mode will keep constant air flow through the rear air extractors and other small areas, helping minimize dust ingress.
Source components: BACK OVER PREVENTION · STRUCTURE:BODY:DOOR.
Source record 10228880 at NHTSANHTSA communication ID: 10228876
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
Source components: SERVICE BRAKES.
Source record 10228876 at NHTSANHTSA communication ID: 10226948
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015-2020 Model Year F-150 Vehicles Equipped with a Power Release Tailgate - Unintended Tailgate Opening REASON FOR THIS SUPPLEMENT Parts ordering information and full repair instructions are now available to support completion of this customer satisfaction program.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · LATCHES/LOCKS/LINKAGES:FUELING/CHARGING DOOR/HATCH/PORT:LATCH/LOCK RELEASE SYSTEM · UNKNOWN OR OTHER.
Source record 10226948 at NHTSANHTSA communication ID: 10226756
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2022 F-150 and 2017-2022 F-Super Duty vehicles may experience issues with the tailgate center step moulding. If there is an issue with the center molding (warped, damaged condition, loose, or if the molding is missing), the trim cover is now available separately. It is no longer necessary to replace the entire rear step assembly (402A48).
Source components: STRUCTURE:BODY:TAILGATE.
Source record 10226756 at NHTSANHTSA communication ID: 10222789
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2022 F-250-F-550, 2015-2020 F-150 and 2018-2022 Expedition vehicles without push button start and passive entry may exhibit a condition where it is difficult to insert the ignition key and/or turn it to the accessory position when removing the ignition lock cylinder per the functional lock cylinder service procedure in Workshop Manual (WSM), Section 501-14. This may be due to debris or contamination in the ignition lock cylinder. If this concern occurs, use a suitable shop vacuum to dislodge or remove debris or contamination by placing the vacuum hose over the lock cylinder, without the key installed, for 30 seconds. Insert the ignition key and reattempt turning it to the accessory position for lock cylinder removal. If the key will not turn to the accessory position, continue with the non-functional lock cylinder removal procedure.
Source components: ELECTRICAL SYSTEM:STARTER ASSEMBLY.
Source record 10222789 at NHTSANHTSA communication ID: 10222788
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10222788 at NHTSANHTSA communication ID: 10217028
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2022 Ford/Lincoln customers may experience a notification in the FordPassÃÂÃÂÃÂî/LincolnWayÃÂÃÂÃÂî app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
Source components: ELECTRICAL SYSTEM.
Source record 10217028 at NHTSANHTSA communication ID: 10216060
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2022 F-150, 2017-2022 F-Super Duty and 2018-2022 Expedition/Navigator vehicles may exhibit poor air conditioning (A/C) performance. Workshop Manual (WSM) diagnostic procedures have been updated to more accurately diagnose A/C performance concerns. Refer to the updated Diagnosis and Testing, and General Procedure in the WSM, Section 412-00 Climate Control System for diagnostic procedures
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER · VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM.
Source record 10216060 at NHTSANHTSA communication ID: 10214832
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2022 Ford and Lincoln vehicle owners may experience a condition of missing authorization, command and control, battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.
Source components: ELECTRICAL SYSTEM.
Source record 10214832 at NHTSANHTSA communication ID: 10214754
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 (non-Raptor) vehicles equipped with 4WD may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure to remove and cap the vacuum supply line or to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.
Source components: POWER TRAIN.
Source record 10214754 at NHTSANHTSA communication ID: 10214133
NHTSA source summary · Original PDF not reviewed by Recallfolio
In the affected vehicles, some customers report experiencing an unintended tailgate opening and may have previously serviced their vehicle for this concern. Ford has developed an enhanced remedy for customers who may want this enhanced repair performed on their vehicle.
Source components: LATCHES/LOCKS/LINKAGES · LATCHES/LOCKS/LINKAGES:TAILGATE:LATCH.
Source record 10214133 at NHTSANHTSA communication ID: 10212957
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
Source components: ELECTRICAL SYSTEM.
Source record 10212957 at NHTSANHTSA communication ID: 10212106
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 F-150 2018-2020 Expedition/Navigator vehicles built on or before 31-Oct-2019 and equipped with a 3.5L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure steps to replace the VCT units.
Source components: ENGINE AND ENGINE COOLING.
Source record 10212106 at NHTSANHTSA communication ID: 10211996
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015-2020 Model Year F-150 Vehicles Equipped with a Power Release Tailgate - Unintended Tailgate Opening - In the affected vehicles, some customers report experiencing an unintended tailgate opening and may have previously serviced their vehicle for this concern. Ford has developed an enhanced remedy for customers who may want this enhanced repair performed on their vehicle.
Source components: LATCHES/LOCKS/LINKAGES:TAILGATE:LOCK · UNKNOWN OR OTHER.
Source record 10211996 at NHTSANHTSA communication ID: 10212120
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150, 2017-2022 Super Duty and 2018-2021 Expedition vehicles may experience a cracked or splitting driver air bag cover. This may be due to the air bag cover tear seam design. An updated driver air bag assembly has been released with a more robust air bag cover design. Refer to Workshop Manual (WSM), Section 501-20B for the replacement procedure. If servicing under warranty, use causal part 15043B13 for F-150 and Expedition or 25043B13 for Super Duty and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: AIR BAGS.
Source record 10212120 at NHTSANHTSA communication ID: 10210816
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2021 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: COMMUNICATION:MANUFACTURER TELEMATICS.
Source record 10210816 at NHTSANHTSA communication ID: 10210471
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 F-150, 2018-2022 Expedition/Navigator/Mustang and 2019-2022 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware break-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
Source record 10210471 at NHTSANHTSA communication ID: 10210941
NHTSA source summary · Original PDF not reviewed by Recallfolio
In various 2017-2022 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating "Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option
Source components: COMMUNICATION:MANUFACTURER TELEMATICS · EQUIPMENT.
Source record 10210941 at NHTSANHTSA communication ID: 10209366
NHTSA source summary · Document-reviewed explainer available below
Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine - Cam Phase Replacement. Parts Requirements / Order information - Intake Gaskets HL3Z-9439-A should be inspected and only replaced if damaged. It is no longer required to replace these gaskets.
Source components: ENGINE AND ENGINE COOLING.
3.5L cam phaser program: Historical deadline: Jan 2023
Read coverage & conditionsNHTSA communication ID: 10209209
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
Source components: EQUIPMENT · EQUIPMENT:MECHANICAL · SEATS.
Source record 10209209 at NHTSANHTSA communication ID: 10209031
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2022 F-150, 2017-2022 F-Super Duty and 2018-2022 Expedition/Navigator vehicles may exhibit poor air conditioning (A/C) performance, loss of airflow and/or engine cooling fans running continuously from high A/C pressures. This concern may be from the evaporator freezing up due to the evaporator temperature sensor being biased. To correct the condition, follow the Service Procedure steps to replace the evaporator temperature sensor.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN · UNKNOWN OR OTHER.
Source record 10209031 at NHTSANHTSA communication ID: 10208146
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Focus/MKX/C-MAX, 2017-2019 MKC/Taurus/Flex/MKT, 2017-2020 Fusion/MKZ/Continental, 2017-2022 Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.
Source components: SEATS.
Source record 10208146 at NHTSANHTSA communication ID: 10207139
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 F-150 vehicles built on or before 01-Feb-2021, 2017-2020 F-150 vehicles equipped with a 3.5L EcoBoost engine, 2018-2020 F-150 vehicles equipped with a 2.7L EcoBoost or 5.0L engine, 2019-2020 F-150 vehicles equipped with a 3.0L diesel engine may exhibit a high pitched squeal or whistle type noise from the engine compartment after the engine is shut off. This condition may be due to the air conditioning (A/C) low side system pressure exceeding the high side pressure resulting in equalization of A/C system pressures through the A/C compressor. An updated A/C compressor has been released to resolve this concern. For claiming, use causal part 19703 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10207139 at NHTSANHTSA communication ID: 10207126
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150 vehicles may experience a cracked or splitting driver air bag cover. This may be due to the air bag cover tear seam design. An updated driver air bag assembly has been released with a more robust air bag cover design. Refer to Workshop manual (WSM), Section 501-20B for the replacement procedure. If servicing under warranty, use causal part 15043B13 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: AIR BAGS · EQUIPMENT.
Source record 10207126 at NHTSANHTSA communication ID: 10206843
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 F-150, 2017-2021 Super Duty and 2018-2021 Expedition/Navigator vehicles may exhibit poor air conditioning (A/C) performance, loss of airflow and/or engine cooling fans running continuously from high A/C pressures. This concern may be from the evaporator freezing up due to the evaporator temperature sensor being biased. To correct the condition, follow the Service Procedure steps to replace the evaporator temperature sensor.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
Source record 10206843 at NHTSANHTSA communication ID: 10205694
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10205694 at NHTSANHTSA communication ID: 10205526
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2315 to increase the labor operation time allowances. Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang and 2019-2021 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware wear-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.
Source components: POWER TRAIN.
Source record 10205526 at NHTSANHTSA communication ID: 10204046
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine Cam Phaser Replacement REASON FOR THIS SUPPLEMENT ⢠Parts Requirements / Ordering Information - Due to limited availability of originally specified parts, alternate option parts have been added. ⢠Submitting Claims with Customer Loyalty Program for Balance Remaining â Added instructions on how to use Lincoln Loyalty funds.
Source components: ENGINE AND ENGINE COOLING.
Source record 10204046 at NHTSANHTSA communication ID: 10203841
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: COMMUNICATION:MANUFACTURER TELEMATICS · UNKNOWN OR OTHER.
Source record 10203841 at NHTSANHTSA communication ID: 10202720
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine PCM Reprogram Due to Engine Shudder; Owner Letter sent
Source components: ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE.
Source record 10202720 at NHTSANHTSA communication ID: 10201905
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang and 2019-2021 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware wear-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10201905 at NHTSANHTSA communication ID: 10201606
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Expedition/Navigator, 2015-2020 F150 and 2017-2020 F-Super Duty vehicles equipped with power running boards (PRB) may exhibit a condition where the PRBs are disabled, changing the feature menu setting from Auto to Off mode in the instrumental panel cluster (IPC), DTC U3003:16 stored in the running board control module (RBM) and with or without an illuminated charging system indicator lamp. This may be due to a low battery voltage event or a fully discharged battery. To correct this condition, inspect the charging system and correct the low battery voltage event. Refer to Workshop Manual (WSM), Section 501-08 > Diagnosis and Testing. Configure the PRB system mode from Off to Auto mode in the Advance Settings of the IPC. Refer to the Owner's Manual > Power Running Boards.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10201606 at NHTSANHTSA communication ID: 10201669
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine Cam Phaser Replacement; Owner letters are scheduled to mail during the week of September 27, 2021⢠Submitting Claims with Ford Protect for Balance Remaining: Added instruction on how to claim the customer paid portion of the FSA with Ford Protect.⢠Submitting Claims with Customer Loyalty Program for Balance Remaining: Added instruction on how to claim the customer paid portion of the FSA using CLP Funds. This program extends the warranty coverage of the engine cam phasers until January 1, 2023 provided the Repair Order (RO) date of Powertrain Control Module reflash under Customer Satisfaction Program 21B10 occurs on or before February 28, 2022
Source components: ELECTRICAL SYSTEM:ADAS:CONTROL MODULE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE.
Source record 10201669 at NHTSANHTSA communication ID: 10201668
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine PCM Reprogram Due to Engine Shudder ;In a very low percentage of the affected vehicles, an engine shudder may develop after receiving the PCM update provided in program 21B10. For peace of mind, Ford is providing a no-cost, one-time repair for customers who receive the PCM update under program 21B10 to revert the PCM calibration back to its original state before program 21B10.
Source components: ELECTRICAL SYSTEM.
Source record 10201668 at NHTSANHTSA communication ID: 10201643
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine Powertrain Control Module Reprogram for Cam Phaser Rattle
Source components: ELECTRICAL SYSTEM.
Source record 10201643 at NHTSANHTSA communication ID: 10201618
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 F-150, 2017-2021 F-Super Duty and 2018-2021 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit a binding/sticking, glass stuck open or closed, noisy operation including chatter, rattling, or grinding. This may be due to the glass panel brackets cracking and/or breaking apart. The glass panel brackets are serviceable separately from the frame assembly and require the roof opening panel glass to be moved to the vent position. To correct the condition, follow the Service Procedure to replace the roof opening panel glass brackets
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · STRUCTURE:BODY:ROOF AND PILLARS · VISIBILITY:SUN/MOON ROOF ASSEMBLY.
Source record 10201618 at NHTSANHTSA communication ID: 10201579
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2021 Ford and Lincoln vehicles equipped with 3.3L, 3.5L EcoBoost, or 5.0L engines may exhibit stalling, lack of power, low fuel rail pressure and/or DTCs P0087 or P008A after a repair was made that required the removal of the fuel line that connects the high-pressure fuel pump to the port injection rail, such as injector replacements or base engine repairs. This line must be installed in the correct orientation as it has an internal one-way check valve. To determine if the fuel line has been installed improperly, look at the position of the Oetiker clamp (stainless band clamped around the black fuel line). The clamp holds the one-way check valve in place and should be located closest to the end connected to the port injection rail. If the clamp is not closest to the port injection rail, remove and reinstall the line in the proper orientation.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
Source record 10201579 at NHTSANHTSA communication ID: 10201612
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150, 2017-2020 Super Duty and 2018-2020 Expedition/Navigator vehicles may exhibit poor air conditioning (A/C) performance, loss of airflow and/or engine cooling fans running continuously from high A/C pressures. This concern may be from the evaporator freezing up due to the evaporator temperature sensor being biased. To correct the condition, follow the Service Procedure steps to replace the evaporator temperature sensor.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10201612 at NHTSANHTSA communication ID: 10201050
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM.
Source record 10201050 at NHTSANHTSA communication ID: 10201034
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
Source components: SERVICE BRAKES, ELECTRIC:SOFTWARE/PROGRAMMING.
Source record 10201034 at NHTSANHTSA communication ID: 10201022
NHTSA source summary · Original PDF not reviewed by Recallfolio
2017-2020 F-150 vehicles equipped with a 3.5L engine and a 10R80 transmission may experience an error message while performing Transmission Characterization/Solenoid IDN with IDS v122.05 or v122.06 stating "Unable To Communicate With The Module". This is due to an issue with the Transmission Characterization/Solenoid IDN tool in IDS v122.05 and v122.06. To resolve the issue, uninstall IDS from the computer. Then, run the IDS clean up utility tool, located on PTS > Rotunda Tab > Diagnostic Tool Support > IDS Support > IDS troubleshooting guide. Next, install IDS v123.01 (123_FULL) and retry the Transmission Characterization/Solenoid IDN tool using IDS level v123.01.
Source components: ELECTRICAL SYSTEM.
Source record 10201022 at NHTSANHTSA communication ID: 10201019
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2021 Ford and Lincoln vehicle customers may receive a message in their FordPass or Lincoln Way App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.
Source components: POWER TRAIN:MANUAL TRANSMISSION:INTERNAL:DOGS/SYNCHROS.
Source record 10201019 at NHTSANHTSA communication ID: 10201013
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
Source components: ELECTRICAL SYSTEM.
Source record 10201013 at NHTSANHTSA communication ID: 10200998
NHTSA source summary · Original PDF not reviewed by Recallfolio
2017-2020 F-150 vehicles equipped with a 3.5L engine and a 10R80 transmission may experience an error message while performing Transmission Characterization/Solenoid IDN with IDS v122.05 stating "Unable To Communicate With The Module". A temporary workaround to complete programming is as follows: Uninstall IDS from the computer. Then, run the IDS clean up utility tool, located on PTS > Rotunda Tab > Diagnostic Tool Support > IDS Support > IDS troubleshooting guide. Next, Install IDS v122.01 (122_FULL) and retry the Transmission Characterization/Solenoid IDN using IDS level 122.01. Monitor OASIS for updates.
Source components: ELECTRICAL SYSTEM.
Source record 10200998 at NHTSANHTSA communication ID: 10201090
NHTSA source summary · Original PDF not reviewed by Recallfolio
In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time or as a knocking noise when the engine is idling after it is warmed up. These concerns should be addressed by the updated calibration provided in FSA 21B10. However, for peace of mind, Ford is providing an extended warranty for customers who receive the PCM update under program 21B10 prior to December 21, 2021 and continue to experience cam phaser noise after receiving that PCM update.
Source components: ENGINE AND ENGINE COOLING.
Source record 10201090 at NHTSANHTSA communication ID: 10201088
NHTSA source summary · Original PDF not reviewed by Recallfolio
It may be possible that an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after your vehicle was turned off for an extended period of time, or as a knocking noise when the engine is idling after it is warmed up.
Source components: ENGINE AND ENGINE COOLING.
Source record 10201088 at NHTSANHTSA communication ID: 10199536
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
Source components: SEATS.
Source record 10199536 at NHTSANHTSA communication ID: 10199482
NHTSA source summary · Original PDF not reviewed by Recallfolio
In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time or as a knocking noise when the engine is idling after it is warmed up. These concerns should be addressed by the updated calibration provided in FSA 21B10. However, for peace of mind, Ford is providing an extended warranty for customers who receive the PCM update under program 21B10 prior to December 31, 2021 and continue to experience cam phaser noise after receiving that PCM update, A cam phaser that has developed an undesirable noise does not affect the vehicle safety, performance, or emissions.
Source components: ENGINE AND ENGINE COOLING.
Source record 10199482 at NHTSANHTSA communication ID: 10199480
NHTSA source summary · Original PDF not reviewed by Recallfolio
In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time, or as a knocking noise when the engine is idling after it is warmed up. A cam phaser that has developed an undesirable noise does not affect the vehicle safety, performance, or emissions.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10199480 at NHTSA