2016 Ford F-150 Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–200 of 283, ordered newest first. Dated records on this page: Oct 6, 2017–Aug 7, 2019.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Aug 7, 2019Service Bulletin/Repair Instructions
TSB 19-2205
NHTSA communication ID: 10164470
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. This may be due to a lack of RTV adhesion. This article includes detailed steps to achieve proper RTV adhesion. To correct the condition, follow the Service Procedure steps to replace the oil pan.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only be replaced for this condition when the 232 key table error message is present. If the 232 key table error is not present, follow normal diagnostics for the no crank condition. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150/Expedition/Navigator vehicles equipped with a 3.5L/2.7L EcoBoost engine and four-wheel drive (4WD) may exhibit an intermittent grinding type noise while driving in two-wheel drive (2WD), most commonly on acceleration. This noise could appear to be turbocharger related. After engineering analysis of returned turbochargers that have been replaced for this condition, no concerns were identified with the turbochargers. The grinding type noise may be related to the 4WD system integrated wheel ends (IWE). To aid in diagnosis, shift the vehicle to 4WD and attempt to verify the condition. If the grinding noise no longer occurs with the vehicle in 4WD a IWE vacuum system and/or mechanical fault may be present.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit excessive white or blue smoke from the exhaust at start up after a cold soak. This may be due to oil entering the left hand turbocharger turbine housing. To correct the condition, follow the Service Procedure steps to replace the left hand turbocharger oil supply tube with a revised part.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150 vehicles may exhibit a glove compartment door that appears misaligned along the storage tray or right side instrument panel when closed. This may be due to the position of the glove compartment storage tray rubber mat or the seating of the glove compartment door strikers or glove compartment door hinge pins. To resolve the condition, follow the Service Procedure steps to reposition or adjust the affected component.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 F-150/Mustang, 2015-2018 Edge/MKC, 2016-2018 MKX, 2013-2018 Explorer/Taurus/Flex/MKT, and 2017-2018 Fusion/MKZ/Continental vehicles built on or before 19-Oct-2017 may exhibit an inoperative adaptive cruise control, collision warning, and/or collision avoidance system with a Pre-Collision Assist Not Available, Collision Warning Not Available, and/or Adaptive Cruise Fault message present in the instrument panel cluster (IPC) and diagnostic trouble code (DTC) U3000:49 present in the cruise control module (CCM). To resolve the condition, reprogram the CCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 9E731 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150 vehicles may exhibit a rattle and/or squeak noise from the vista roof opening panel while driving with the roof opening panel closed. This may be due to dirt and/or debris build up between the vista roof opening panel seal and the body. To correct the condition, follow the Service Procedure steps to clean and lubricate the vista roof opening panel seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150 vehicles equipped with a 3.3L, 3.5L Duratec, 3.5L EcoBoost and 5.0L engine without a block heater built on or before 1-Jan-2019 may exhibit a lack of heat concern from the heating ventilation and air conditioning (HVAC) system when operating the vehicle in temperatures consistently below -20àâÂÂC (4àâÂÂF). This condition may be due to deposits from the engine coolant becoming trapped in the heater core. To correct the condition, flush the cooling system and replace the heater core. Follow the Service Procedure steps to correct the condition.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150 vehicles equipped with a 3.3L, 3.5L Duratec, 3.5L EcoBoost and 5.0L engine and equipped with a block heater built on or before 1-Jan-2019 may exhibit a lack of heat concern from the heating ventilation and air conditioning (HVAC) system when operating the vehicle consistently in temperatures that are below -20àâÂÂC (4àâÂÂF). This condition may be due to deposits from the engine coolant becoming trapped in the heater core. To correct the condition, flush the cooling system and replace the heater core. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47922 - Various Vehicles - 2.7L/3.0L EcoBoost Engine - Oil Filter Service Tip When servicing the oil filter on vehicles equipped with a 2.7L or 3.0L EcoBoostengine it is critical to inspect the oil filter housing center stem to verify is not separated or damaged. If the center stem is damaged or separated from the housing this will result in oil flow through the reservoir drain port causing low engine oil pressure and internal engine damage. If the filter housing stem is damaged or separated, the oil filter housing must be replaced. If the center stem is not damaged or separated, the O-ring seals on the stem and housing must be replaced each time the filter is serviced.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015 - 2019 Model Year F-150 and 2017 â 2019 Model Year F-Super Duty Vehicles Equipped with Engine Block Heaters - Engine Block Heater Cord Replacement
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150 vehicles may exhibit a glove box door that appears misaligned along the storage tray or right side instrument panel when closed. This may be due to the position of the glove box storage tray rubber mat or the seating of the glove box door strikers or glove box door hinge pins. To resolve the condition, reposition or adjust the affected component according to the Service Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150 XL/XLT vehicles may exhibit warping/separation of the instrument panel at the defrost vents. To resolve the condition, replace the instrument panel upper section.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150 XL/XLT vehicles may exhibit warping/separation of the instrument panel at the defrost vents. To resolve the condition, replace the instrument panel upper section.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2016 F-150 vehicles built on or before 01-Feb-2016, 2019 F-150 vehicles built on 11-Oct-2018 and through 15-Nov-2018 and 2019 F-Super Duty vehicles built on 10-Oct-2018 and through 27-Nov-2018 equipped with adaptive cruise control may exhibit an unintended deceleration event while passing a large object such as a tractor trailer. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2016 F-150 vehicles built on or before 01-Feb-2016, 2019 F-150 vehicles built on 11-Oct-2018 and through 15-Nov-2018 and 2019 F-Super Duty vehicles built on 10-Oct-2018 and through 27-Nov-2018 equipped with adaptive cruise control may exhibit an unintended deceleration event while passing a large object such as a tractor trailer. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F150/Edge, 2016-2018 MKX, 2019 Nautilus and 2017-2019 Fusion/Continental vehicles equipped with a 2.7L engine may exhibit a malfunction indicator lamp (MIL) and/or wrench lamp with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Nautilus/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:COOLING SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F150/Edge, 2016-2018 MKX, 2019 Nautilus and 2017-2019 Fusion/Continental vehicles equipped with a 2.7L engine may exhibit a malfunction indicator lamp (MIL) and/or wrench lamp with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Nautilus/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 F-150 vehicles equipped with a 3.0L diesel engine built on or before 25-Jan-2019 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0234, P208E and/or P2201 stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 F-150 vehicles equipped with a 3.0L diesel engine built on or before 25-Jan-2019 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0234, P208E and/or P2201 stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150 vehicles may exhibit a console media bin door that will not open or is binding. This may be due to the console media bin door inertia switch being stuck in the active position. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150, 2017-2019 F-Super Duty, 2018-2019 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit a binding/sticking, glass stuck open or closed, noisy operation including chatter, rattling, or grinding. This may be due to the glass brackets cracking and/or breaking apart. The glass panel brackets are serviceable separately from the frame assembly and require the roof opening panel glass to be moved to the vent position. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 F-150 vehicles may exhibit DTC C0051 in the ABS module. This DTC compares steering angle between the power steering control module (PSCM) and ABS and may set due to towing, driving in heavy winds, loose suspension or steering gear components, alignment, or harness or connector concerns with the ABS or PSCM circuits. The ABS pinpoint tests AE, LA, or LB may direct a replacement of the PSCM after disconnecting/reconnecting PSCM connectors. Do not replace the PSCM using ABS Pinpoint tests AE, LA, LB. Refer to the Workshop Manual (WSM) Section, 211-02 to locate the correct PSCM pinpoint tests for the PSCM DTCs that are retrieved during the PSCM self-test. The ABS pinpoint tests are in the process of being updated.
Source components: SERVICE BRAKES, AIR:ANTILOCK · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.
Source components: STEERING · STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 F-150 vehicles may exhibit a steering drift, pull, and/or wander. To diagnose these conditions refer to Pinpoint Test (PPT) H - Steering System Pull, Drift, Wander or Steering Wheel is Off Center in Workshop Manual (WSM) Section, 211-00. Do not use PPT I - Poor Returnability Sticky Steering or Binding to diagnose drift, pull, and/or wander symptoms. These Pinpoint Tests are in the process of being updated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2018 Model Year Expedition and Navigator Vehicles Equipped With R-1234yf Refrigerant - Special R-1234yf Refrigerant Service Information. Certain 2015-2018 Model Year F-150 and 2017-2018 Model Year F-250-F-550 - Vehicles - Door Latch Freezing Concerns
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150 vehicles may exhibit a glove box door that appears misaligned along the storage tray or right side instrument panel when closed. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 F-150/Expedition/Navigator vehicles may exhibit an intermittent grinding noise coming from the right or left IWE area in 2WD mode. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 F-150 vehicles equipped with a 2.7L EcoBoost engine and built on 1-Apr-2016 and through 1-Jan-2017 may exhibit white or blue smoke from the exhaust, rough idle in neutral or park at normal operating temperature or after a hot restart. The vehicle may also exhibit an illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTCs) P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0316, P0524 and/or P06DD with the excessive oil consumption. Oil consumption may be 1 liter (1 quart) in less than 4,800 km (3,000 miles). Follow the Service Procedure steps to correct this condition.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150 vehicles equipped with a 3.3L/3.5L Duratec, 3.5L EcoBoost and 5.0L engine and equipped with a block heater may exhibit a lack of heat concern from the heating ventilation and air conditioning (HVAC) system when operating the vehicle consistently in temperatures that are below -20Å?C (4Å?F). This condition may be due to deposits from the engine coolant becoming trapped in the heater core. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150 vehicles equipped with a 3.3L, 3.5L Duratec, 3.5L EcoBoost and 5.0L engine without a block heater may exhibit a lack of heat concern from the heating ventilation and air conditioning (HVAC) system when operating the vehicle in temperatures consistently below -20 degrees C (4 degrees F). This condition may be due to deposits from the engine coolant becoming trapped in the heater core. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. Replace the oil pan following the procedure in Workshop Manual (WSM) Section, 303-01. After removing the oil pan it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV and clean the engine sealing surface using only Motorcraftù Metal Brake Parts Cleaner, then wipe with Motorcraftù Metal Surface Prep Wipes and allow to air dry. Refer to WSM, Section 303-00 > RTV Sealing Surface Cleaning and Preparation. If possible, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Skipping or improperly completing steps may result in repeat oil pan leaks.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, 2017-2018 F-Super Duty, 2018 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit a concern with the glass panel brackets. The brackets may crack and/or break apart resulting in symptoms that include but are not limited to binding/sticking, glass stuck open or closed, noisy operation including chatter, rattling, or grinding. The roof opening panel glass brackets are available for service as a kit (FL3Z-1651070-C). Refer to Workshop Manual (WSM), Section 501-17 for diagnosis and repair procedures. Make sure the track is free of debris prior to assembly. For claiming, use causal part 1651070 and applicable labor operations in Section 12 of the Service Labor Time Standards (SLTS) Manual. Labor operations for removal and installation of the glass and glass brackets (guides) apply.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 F-150, 2015-2018 Transit/Expedition, and 2015-2017 Navigator vehicles equipped with a 3.5L EcoBoost engine with greater than 20,000 miles may exhibit a tick type noise from the cylinder block area. This noise may be caused by a cracked piston skirt. The noise can be isolated to a cylinder using a stethoscope or other suitable listening device. Canceling the affected cylinder will reduce or eliminate the noise. If the noise is isolated to a specific cylinder, it is recommended to replace the short block. If the noise cannot be isolated using the methods described, refer to the Workshop Manual (WSM) for diagnosis. A cracked piston skirt does not result in metal contamination of the engine or any related cylinder head damage. Prior approval for short block replacement is not required under new vehicle limited warranty coverage.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 F-150, 2015-2018 Transit/Expedition, and 2015-2017 Navigator vehicles equipped with a 3.5L EcoBoost engine with greater than 20,000 miles may exhibit a tick type noise from the cylinder block area. This noise may be caused by a cracked piston skirt. The noise can be isolated to a cylinder using a stethoscope or other suitable listening device. Canceling the affected cylinder will reduce or eliminate the noise. If the noise is isolated to a specific cylinder, it is recommended to replace the short block. If the noise cannot be isolated using the methods described, refer to the Workshop Manual (WSM) for diagnosis. A cracked piston skirt does not result in metal contamination of the engine or any related cylinder head damage. Short block replacement does not require prior approval.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 F-150 and 2017-2018 Expedition/Navigator vehicles may exhibit an intermittent grinding noise coming from the right or left IWE area in 2WD mode. This may be caused by an intermittent leak in the check valve. Before completing any normal diagnosis suspect that the check valve is the root cause of the issue. If the check valve has been ruled out as the root cause for the issue refer to Work Shop Manual 308-07 and follow normal diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150 and 2017-2018 F-Super Duty vehicles may exhibit a lack of cooling from the heating ventilation air conditioning (HVAC) system due to a low refrigerant charge. Using an ultraviolet (UV) leak detection light, inspect the condenser near the receiver/dryer cap for the presence of dye. If dye is present, replace the condenser. For claiming, use causal part 19712 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150 may exhibit a dash panel distortion at the defrost duct area. Engineering is investigating the condition. Do not attempt repair at this time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 Expedition/Navigator vehicles built on or before 24-Feb-2018, 2017-2018 F-Super Duty built on or before 26-Feb-2018 and Transit vehicles built on or before 26-Feb-2018 and 2015-2018 F-150 vehicles built on or before 3-Mar-2018 may exhibit a trailer connected and/or disconnected message in the IPC without a trailer connected. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles equipped with a 2.7L or 3.0L EcoBoost engines may exhibit an oil leak from the engine oil pan RTV seal. Replace the oil pan by performing the published Workshop Manual (WSM) service procedures. After removing the oil pan, it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV, clean the engine sealing surface with only Motorcraftù Metal Brake Parts Cleaner then wipe with Motorcraftù Metal Surface Prep Wipes, and allow to air dry as directed in WSM, Section 303-00, RTV Sealing Surface Cleaning and Preparation. If possible, after the new oil pan is installed, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Ford is investigating this concern. Monitor OASIS for future updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 and connected to an iPhone recently upgraded to iOS 11.2.5 may exhibit functional concerns where USB audio playback and App Link will not operate. This may also include, under certain conditions, no Bluetooth streaming. Apple has released iOS 11.2.6 to address this concern. Advise the customer to update the device to iOS 11.2.6 and re-evaluate before performing any diagnosis or repairs for this condition. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 F-150/Expedition/Navigator 4x4 vehicles may exhibit an intermittent grinding noise coming from the right front or left front wheel area while accelerating in 2WD mode. Refer to the Workshop Manual (WSM), Section 308-07, Diagnosis and Testing Symptom Chart - NVH > The front axle makes noise in 2H mode only and generally under heavy throttle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln Vehicle equipped with SYNC 3 and connected to an iPhone recently upgraded to iOS 11.2.5 may exhibit a concern where USB Audio playback and App Link applications will not function properly. This may also include, under certain conditions, no Bluetooth Streaming. Apple is aware of the issue and is working on a resolution with a future iOS release. No repairs should be performed at this time. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device. Monitor OASIS for updates. Customers can also check Apple Support or connect to iTunes for the latest available iOS release for their phone.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150 vehicles equipped with power folding mirrors may exhibit the mirror housing vibrating while driving, moving freely or not moving to the desired position after the mirror is manually folded. Refer to the Owner's Manual for the power mirror synchronization procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, 2017-2018 F-Super Duty, 2018 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit binding while opening or closing of the movable glass panel. The roof opening panel glass brackets are available for service. Both brackets must be replaced, FL3Z-1651070-A right side and FL3Z-1651071-A left side. Refer to Workshop Manual (WSM), Section 501-17 for removal and installation procedure. For claiming, use causal part 1651070 or 1651071. Use part number 51070 to look up applicable labor operations, listed in Section 12 of the Service Labor Time Standards (SLTS) manual
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, 2017-2018 F-Super Duty, 2018 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit binding while opening or closing of the movable glass panel. The roof opening panel glass brackets are available for service. Both brackets must be replaced, FL3Z-1651070-A right side and FL3Z-1651071-A left side. Refer to Workshop Manual (WSM), Section 501-17 for removal and installation procedure. For claiming, use causal part 51070 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual.
Source components: STRUCTURE:BODY:ROOF AND PILLARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, 2017-2018 F-Super Duty, 2018 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit binding while opening or closing of the movable glass panel. The roof opening panel glass brackets are available for service. Both brackets must be replaced, FL3Z-1651070-A right side and FL3Z-1651071-A left side. Refer to Workshop Manual (WSM), Section 501-17 for removal and installation procedure. For claiming, use causal part 51070 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, Mustang and Transit vehicles built on or before 01-Dec-2017 may have a concern of no airflow from the climate control vents. This may be caused by a seized or sticking A/C clutch. This can be repaired by replacing only the A/C clutch (19D786/19D784). The compressor assembly (19703) may not be required. Refer to Workshop Manual, Section 412-00 for A/C clutch removal. It may be necessary to lightly tap around the stuck area of the clutch with a rubber mallet to free it from the pulley for removal. Refer to applicable labor operations from Section 11 of the SLTS maunual when replacing the A/C clutch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, Mustang and Transit vehicles built on or before 01-Dec-2017 may have a concern of no airflow from the climate control vents. This may be caused by a seized or sticking A/C clutch. This can be repaired by replacing only the A/C clutch (19D786/19D784). The compressor assembly (19703) may not be required. Refer to Workshop Manual, Section 412-00 for A/C clutch removal. It may be necessary to lightly tap around the stuck area of the clutch with a rubber mallet to free it from the pulley for removal. Refer to applicable labor operations from Section 11 of the SLTS maunual when replacing the A/C clutch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 F-150 and Expedition vehicles equipped with a SYNC non-touchscreen display may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update APIM software. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available, refer to WSM Section 415-00 and update the APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · EQUIPMENT · LANE DEPARTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, 2017-2018 F-Super Duty, 2018 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit binding while opening or closing of the movable glass panel. The roof opening panel glass brackets are available for service. Both brackets must be replaced, FL3Z-1651070-A right side and FL3Z-1651071-A left side. Refer to Workshop Manual (WSM), Section 501-17 for removal and installation procedure. For claiming, use causal part 1651070 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford or Lincoln vehicles equipped with SYNC 3 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016 F-Super Duty/F-650/750 vehicles equipped with a 6.7L diesel engine or 2016 Transit vehicles equipped with a 3.2L diesel engine may exhibit an illuminated MIL with DTCs P24AE, P24B1, P24DA, P24C6 and/or P24C7 stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
Source components: ELECTRICAL SYSTEM · ENGINE · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2016 F-Super Duty pickup vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with DTCs P2201, P2459, P2463 and/or P246C. Reprogram the powertrain control module (PCM) to the latest calibration using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 106.01 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F150/Edge, 2016-2018 MKX and 2017-2018 Fusion, Continental vehicles equipped with a 2.7L engine may experience a malfunction indicator lamp (MIL) and/or wrench lamp with Diagnostic Trouble Codes (DTCs): P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. If an issue with the wiring is found use causal part 12A699.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 F-150 vehicles may exhibit intermittent and/or inoperative A/C, radio, and/or power window switch control with multiple illuminated warning indicators and/or diagnostic trouble codes (DTCs) U0140, U0155, U0253, U0401, and/or U0452 stored in the front controls interface module (FCIM). This may be caused by excessive network traffic on the controller area network (CAN) Bus causing the FCIM to lock up. Before replacing the FCIM, complete a battery reset, clear all DTCs and run a FCIM self-test. If the issue is still present, follow normal diagnosis. For claiming, use causal part 18842 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150 vehicles equipped with a vista roof opening panel may exhibit binding while opening or closing of the movable glass panel. The roof opening panel glass bracket is available for service. Both brackets must be replaced. Refer to Workshop Manual (WSM), Section 501-17 for removal and installation procedure. For claiming, use causal part 1651070 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016 F-150 vehicles equipped with a 5.0L engine and built on 13-Jan-2016 and through 16-Jul-2016 may exhibit an audible knock noise from the engine only after the engine is at normal operating temperature and between 1500 and 2500 engine RPMs If cylinder #5 is canceled and the noise is no longer present, consider the noise a characteristic and do not attempt any repairs. Engineering has determined there are no long term durability concerns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. To recover the screen, perform any one of the following actions: touch the SYNC screen anywhere outside the vehicle image pop-up box, safely shift the vehicle into and out of reverse, or perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). If this does not resolve the concern, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.