2025 Ford EXPLORER Manufacturer communications & TSBs.Page 1
Original record summaries, dates and identifiers for this model-year. Records 1–100 of 182, ordered newest first. Dated records on this page: Jul 25, 2025–Sep 15, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Sep 15, 2026Service Bulletin/Repair Instructions
SSM 55172
NHTSA communication ID: 11037421
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Aviator/Explorer/Police Interceptor Utility vehicles may exhibit a "Steering Assist Fault Service Required" message and diagnostic trouble codes (DTC) C1110:56 and/or U3000:96 stored in the power steering control module (PSCM) after programming. This may be due to a calibration mismatch in the PSCM which has been resolved in the Ford database. If DTC C1110:56 is stored in a replacement PSCM after completing programmable module installation (PMI), start a new session using the latest software version of the Ford Diagnosis and Repair System (FDRS) scan tool then run the "PSCM - Programmable Module Installation (PMI)" application again. When FDRS asks if the original module is installed, select "No". If DTC C1110:56 is stored in the original PSCM after performing the PSCM configuration, start a new session using the latest software version of the FDRS scan tool, then download and run the "PSCM - Power Steering Control Module (PSCM) Software Update" application. To clear DTC U3000:96 from the PSCM, download and run the "PSCM - Reset the Power Steering Control
Source components: ELECTRICAL SYSTEM · STEERING · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Quality improvements include: -Rear Gate latch calibration update to permit unlatching via the release button when the system has lost position memory and is stuck in a middle-latch position
Campaign / software reference: RGTM-26.AF
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the following vehicles: * 2023-2025 F-Super Duty built on or before 02-Feb-2025 * 2024-2026 Ranger/Bronco/Mustang * 2024-2025 F-150 built on or before 15-Jul-2025 * 2024-2025 Nautilus built on or before 16-Feb-2025 * 2025 Explorer/Aviator built on or before 01-Feb-2025 may exhibit all of the following symptoms: - "No Key Detected" message displayed on the instrument panel cluster (IPC). - Key fob does not work in the backup slot. - Remote keyless entry (RKE) (lock and unlock from the key fob) functionality will work to lock/unlock the vehicle. If the vehicle exhibits these symptoms, start the vehicle using both key fobs. If the no crank/no start condition with "No Key Detected" concern is present, reprogram both key fobs and retest. If the no crank/no start condition with "No Key Detected" is still present, replace the body control module (BCM). Refer to Workshop Manual (WSM), Section 419-10. For claiming, use causal part 15604 and labor operation MT55118SSM up to 1.8 hours.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the following vehicles: * 2025-2026 Expedition/Navigator built on or after 02-Feb-2025 * 2025-2026 F-Super Duty built on or after 02-Feb-2025 * 2025-2026 Explorer/Aviator built on or after 02-Feb-2025 * 2025-2026 Nautilus built on or after 17-Feb-2025 * 2025-2026 F-150 built on or after 16-Jul-2025 may exhibit all of the following symptoms: - "No Key Detected" message displayed on the instrument panel cluster (IPC) - Key fob does not work in the backup slot. - Remote keyless entry (RKE) (lock and unlock from the key fob) functionality will work to lock/unlock the vehicle. If the vehicle exhibits these symptoms, manually enter the vehicle identification number (VIN) into the VIN entry dialog in the Ford Diagnosis and Repair System (FDRS) and then start a session using the Vehicle Communication Module (VCM) II, VCM 3, Vehicle Communication and Measurement Module (VCMM) or later level device with a universal serial bus (USB) cable disconnected from the laptop. Download the "BCM - Body Control Module (BCM) Hardware Test" app
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For Various Ford and Lincoln vehicles, if diagnostics lead to the replacement of the front seat cushion cover J-clips, lower-level service parts are now available. Use service part W709919-S901 if the J-clip is completely detached from the seat cover and W715386-S424 if the clip is still partially attached. It is not necessary to replace the seat cover if only the J-clip is separating from the cover. Refer to PTS Home > Technical Assistance > Technical Support Videos > Section 501- Body and Paint > Seat J-Clips. For claiming, use causal parts from list below and labor operations 63100A and 63100A5. Causal Parts for claiming: Bronco/Bronco Sport/Escape/Explorer/Expedition/Navigator: 7862900 or 7862901 F-150/F-Super Duty: 1562900 or 1562901 Ranger/Maverick: 6062900 or 6062901
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2025 Explorer vehicles equipped with a power roof opening panel may exhibit a sunshield with localized bunching or binding/inoperative. This may be due to a broken or missing sunshield fabric retainer/clip. A revised sunshield clip (LJ6Z-5452118-B) is now available to address this condition. It is not necessary to replace the entire sunshield assembly if the clip(s) are broken or missing. Refer to Workshop Manual (WSM), Section 501-17 Roof Opening Panel > General Procedures > Inspection and Replacement of the Roof Opening Panel Shield Clip.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2026 Explorer vehicles built on or before 27-Feb-2026 and equipped with the panoramic glass roof may exhibit an uneven gap at the front edge of the roof opening panel shield when fully closed. The gap is an appearance issue only, but may allow outside light to pass through the opening. A new gap hider seal has been released to correct this condition (service part number SB5Z-7851884-A). Adjustment or replacement of the glass, shade or headliner assembly is not necessary. The new seal is installed directly onto the existing vertical flange that is present and visible at the front of the opening when the shade is opened. Once installed, the front edge of the shade will press against the new seal when fully closed. To install, center the seal in the opening with the flexible material facing the power shade and press the seal u-channel over the vertical flange. Explorer vehicles built on or after 27-Feb-2026 have the seal already installed and can be referenced if necessary. Once the seal is installed, perform the shield/shade initialization procedure in Workshop Manual (WSM), Section 501-05 > Gen
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine, 2020-2026 Explorer vehicles equipped with a 3.3L hybrid engine, and 2020-2023 Lincoln Aviator vehicles equipped with a 3.0L EcoBoost hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the belt integrated starter generator (BISG). For vehicles with this condition, follow the necessary Pinpoint Test in Workshop Manual (WSM), Section 303-06 for DTC P0A1E and repair the vehicle as directed. Note that previous replacement of the BISG does not negate the need for subsequent BISG replacements if directed to do so by the appropriate Pinpoint Test diagnostics. Engineering is investigating this BISG quality concern. Monitor PTS for updates regarding this investigation.
Source components: ELECTRICAL SYSTEM · FUEL/PROPULSION SYSTEM · POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 25-2415. Reason for update: To add production build dates of the right-side engine valve cover. Some of the vehicles listed in the Model statement above may exhibit oil consumption and blue smoke from the tailpipe. This may be due to the sealing process of the positive crankcase ventilation (PCV) baffle which is part of the valve cover assembly.
Source components: ENGINE · FUEL/PROPULSION SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
Source components: ELECTRICAL SYSTEM · FUEL/PROPULSION SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Quality improvements include: - Updates the connectivity settings to remove an outdated ePrivacy sub-menu, ensuring all displayed options are active and relevant.
Campaign / software reference: ECG-26.2.11.5
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NEW VEHICLE DELIVERY HOLD - Emissions Recall 26E04 Certain 2021-2025 Model Year F-150, Maverick, Mustang, Ranger, Expedition, Bronco Sport, Explorer, Bronco, Navigator, and Aviator Vehicles Powertrain Control Module Software Update
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0300 and/or P0316 stored in the powertrain control module (PCM) (with no other relevant DTCs present) during a cold start after a 3 to 8 hours cold soak. This may be due to the machining surface of the intake ports in the cylinder head.
Source components: ELECTRICAL SYSTEM · ENGINE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 26-2150. Reason for update: To remove the M6 nut from the part list and remove the Steps to install the M6 nut from the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * "Steering Assist Fault Service Required" message displayed in the instrument panel cluster (IPC) * Reduced steering assist * Diagnostic trouble codes (DTCs) U3008:1B and/or U3009:1B stored in the power steering control module (PSCM) This may be due to the PSCM ground connections.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Program 26B14 Certain 2025 Model Year Explorer Vehicles Missing Google Automotive Services Accessory Protocol Interface Module (APIM) Software Update
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Explorer/Aviator/Police Interceptor Utility non-hybrid vehicles built on 06-Feb-2025 and through 13-Dec-2025 may exhibit various drivability symptoms including a rough idle or hesitation shortly after refueling. These symptoms may also be accompanied by liquid fuel in the fuel vapor lines and fuel vapor canister as well as an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0133, P0300, P0301, P0302, P0303, P0304, P0305, and/or P0306 stored in the powertrain control module (PCM). This condition may be due to an intermittently sticking fuel level vent valve on the fuel tank allowing fuel to enter the evaporative emissions system lines and evaporative emissions canister during refueling. If the customer states that the drivability symptoms occurred after recently filling the vehicle, replace the fuel tank (9002) and evaporative emissions canister (9D653). Refer to Workshop Manual (WSM), Section 310-01 to replace the fuel tank. Refer to WSM, Section 303-13 to replace the evaporative emission canister. For claiming use causal part 9002 and labor operations 90
Source components: FUEL/PROPULSION SYSTEM · POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Explorer Platinum vehicles may exhibit a chirp sound instead of a horn honk when locking or remote starting the vehicle. This is intended operation after a recent over-the-air (OTA) update that enabled the open on approach feature. No diagnostics or repairs should be performed for this condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 20202026 vehicles equipped with the 10R60 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. Workshop Manual (WSM) updates related to this diagnostic procedure are planned for release in Q4 2026. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification for transmission replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 26-2112. Reason For Update: add 2026 model year vehicles, update LV fluid XT-10-QLVC and CXT-10-LV6 description to add "Transfer Case Fluid 4WD Only", and update Step 4 to inspect/replace 7H351 and 7B177 outside of this article. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated MIL with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Explorer/Aviator vehicles may exhibit a no crank/no start/discharged battery condition with diagnostic trouble codes (DTC) B144D:29, B144E:29, B1555:29, B1556:29 and/or U3003:16 stored in the rear gate trunk module (RGTM). The power liftgate may also be inoperative. This may be due to water intrusion into the left and/or right power liftgate motors caused by a loose grommet on the electrical harness at the body pass-through. To correct this condition, install a new power liftgate motor corresponding to the DTC(s) set in the RGTM (B144D:29/B144E:29 Ýleft¨ or B1555:29/B1556:29 Ýright¨). To prevent water intrusion into the new liftgate motor, make sure the grommet on the new motor is seated properly by pushing on the grommet at the body pass-through until it clicks into place. For claiming, use causal part 14B351 (Explorer) or 14B350 (Aviator) and labor operations 12651D and 14350AL (left) or 14350AR (right) or 14350AT (both) <br /><br /> If a vehicle with this concern exhibits water intrusion, corrosion, or unseated grommets in or around the liftgate motor, submit a Global Concern Report
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Engine misfire condition * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0301, P0302, P0303, and/or P0304 stored in the powertrain control module (PCM)
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2026 Explorer/Escape/Corsair, 2021-2026 Bronco Sport/Bronco, 2022-2026 Maverick, 2024-2026 Mustang/Ranger/Nautilus vehicles equipped with a 2.0L or 2.3L EcoBoost engine may require removal of the turbocharger wastegate control actuator linkage for various reasons. The Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger - 2.0L/2.3L EcoBoost > Removal and Installation > Wastegate Control Actuator Linkage service procedure been added. In addition, the wastegate actuator rod (9E408), associated retention springs (9342) and retaining clips (00817) have been released as lower-level components to complete the repair without replacing the entire turbocharger wastegate actuator assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 25-2213. Reason for update: update the Service Procedure to add notes to clarify the customer symptoms, applicability of this TSB, directing technicians to evaluate both front strut mounts, and add Figure 1 to identify the specific area of the strut mount to observe. Some of the vehicles listed in the Model statement above may exhibit a click/pop noise while turning the steering wheel from straight ahead to full lock during low speed turning events. This noise may be due to the front upper strut mount washer movement under steering loads.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2026 Nautilus and 2025-2026 Explorer/Aviator vehicles equipped with power autofold exterior mirrors may exhibit concerns with the passenger mirror not automatically folding in or out at times, while the driver side mirror automatically folds properly. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 14B291 and labor operation MT14B291SSM up to 0.4 hours.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2026 Explorer/Police Interceptor Utility/Aviator vehicles may require replacement of the front drive halfshaft inner/outer CV joint boot for various reasons. If Workshop Manual (WSM), Section 205-04 > Diagnosis and Testing leads to CV joint boot replacement, L1MZ-3A331-G (Explorer/Police Interceptor Utility front inner/outer CV joint boot kit), L1MZ-3A331-H (Aviator front inner/outer CV joint boot kit), L1MZ-3A331-F (Explorer/Police Interceptor Utility front inner CV joint boot kit) and L1MZ-3A331-E (Aviator front inner CV joint boot kit) have been released for service. Refer to WSM, Section 205-04 for Removal and Installation procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 25-2621. Reason for update: add 2026 model year vehicles and Transit, update the causal part number (15604), update the Service Procedure, update the service labor operations for 2023 F-Super Duty, and add service labor operations for Transit. Some vehicles listed in the Model statement above may exhibit a no crank/no start condition where the customer cannot start their vehicle. The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 20242025 Explorer vehicles built on 01-Feb-2024 and through 31-Jul-2024 may exhibit a rattle/clunk/knock noise from the front suspension at low speeds between 830 mph (1348 km/h) over harsh/uneven pavement such as cracks and small bumps while driving straight (not while turning). This condition may be due to a loose pressure tube within the front strut assembly and may be present in either front strut. In some cases, a louder noise from one strut can mask a lesser noise from the opposite strut, which may result in only one strut being replaced and a repeat visit if the other strut later becomes apparent. When diagnosing, evaluate both front struts for the concern. To repair, replace the affected front strut(s) as necessary. For claiming, use causal part 18124 and labor operation 18124A (one side) or 18124AT (both sides). If the noise persists, refer to Workshop Manual (WSM), Section 204-01 for normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Explorer/Aviator and 2026 Expedition/Navigator vehicles may exhibit an intermittent inoperative remote start feature using either the key fobs or the Ford/Lincoln App. This may be due to the software in the body control module (BCM). After replicating the concern, use the Ford Diagnosis and Repair System (FDRS) to monitor the RMTSTRT_F_ARB_LST and RMTSTRT_F_TRGT_NM parameter identification (PIDS) in the BCM. If both PID values show "true" in any of the last 5 saved values, engineering is currently working on a solution for this condition that is expected in Q4 2026. Schedule service appointments for customers once the repair becomes available. If either of the BCM PID values do not show "true" in any of the saved values, refer to Workshop Manual (WSM), Section 501-14 Handles, Locks, Latches, Entry Systems > Diagnosis and Testing > Locks, Latches and Entry Systems > Pinpoint Test R (Explorer/Aviator)/Pinpoint Test V (Expedition/Navigator) for normal diagnostics and repair as necessary outside of this article. For claiming, use causal part 15604 and labor operations 12651D and 12651D45
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine and 2020-2026 Explorer vehicles equipped with a 3.3L hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the software within the belt integrated starter generator (BISG). For vehicles with this condition, follow Pinpoint Test I: Battery Isolation/Voltage Stabilization Control Circuit Carry Outance located in the Workshop Manual (WSM), Section 303-06D and repair the vehicle as necessary. Note that the BISG is on backorder status at the time of this publication and Ford is working to make parts available. Engineering is investigating this concern. Monitor PTS for updates.
Source components: ELECTRICAL SYSTEM · ENGINE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit an inoperative dark car mode. The vehicle may exhibit at least one of the following features remaining functional when dark car mode is enabled: * Illuminated odometer, compass, outside air temperature, audio/phone display. * Illuminated main message center display area. * Courtesy lighting * Welcome/farewell animation * Night lock indicator * Passenger airbag disable (PAD) indicator dims to minimum brightness * Locking flash/horn feedback This may be due to the software in the body control module (BCM) and the accessory protocol interface module (APIM).
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Explorer vehicles equipped with a 2.3L EcoBoost engine and built on 16-Aug-2025 and through 5-Mar-2026 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0335 stored in the powertrain control module (PCM). DTC P033F may also be stored in the PCM. This may be due to a pin fit concern at PCM connector C1381E pin 7. To correct this condition, install a new terminal in wiring harness connector C1381E pin 7 (GN/BN) using terminal repair kit DU2Z-14474-CA. Refer to Wiring Diagram, Cell 5 for wiring repair information. For claiming use causal part 12A581 and labor operations 12650D and 12650D45WR.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Aviator and 2025-2026 Explorer/Police Interceptor Utility hybrid vehicles may exhibit a "Refuel Error See Manual" message in the instrument panel cluster (IPC) after installing a replacement fuel filler door assembly (7827936). This may be due to a concern with the replacement fuel filler door assembly. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and Ford is currently working on a solution for this condition that is expected Q3 2026. Further replacement of the fuel filler door assembly will not resolve this condition at this time. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.<br /><br /> If a customer vehicle exhibits this concern, submit a Vehicle Concern Report. To submit a report, click on the "Submit Global Concern Report (GCR)" link at the upper right of the PTS Vehicle ID screen (vehicle identification number ÝVIN¨ required) a
NHTSA source summary · Original PDF not reviewed by Recallfolio
Quality improvements include: -Updates the Restraint Control Module to prevent a potential internal fault that may cause a warning light to illuminate for one key cycle
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 26-2100. Reason for update: To update vehicle symptoms, affected vehicle lines, and model years. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Poor speaker sound quality (static, pop, crackle) while using Apple CarPlay® or Bluetooth audio Poor or muffled outbound phone call sound quality while using Apple CarPlay® or Bluetooth audio This may be due to the software in the accessory protocol interface module (APIM).
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine and 2020-2026 Explorer vehicles equipped with a 3.3L hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the software within the belt integrated starter generator (BISG). For vehicles with this condition, follow Pinpoint Test G located in the Workshop Manual (WSM), Section 303-06D and repair the vehicle as necessary. Note that the BISG is on backorder status at the time of this publication and Ford is working to make parts available. Engineering is investigating this concern. Monitor PTS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2026 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit an illuminated malfunction indicator (MIL) lamp with engine over-temperature warning in the message center and poor air conditioning (A/C) performance from the engine cooling fan not running. Diagnostic trouble codes (DTC) B3A1B, P0113, P0217, and/or P0480 may be stored in the powertrain control module (PCM). This may be due to poor engine compartment ground connections at G105, G107, G111 and/or G122. Refer to the Wiring Diagram (WD) > Grounds Cell 010 > Pages 2, 3, 7 and 8. Prior to any Workshop Manual (WSM) diagnostics, verify all listed grounds are tightened to 62 lb-in (7 Nm) to resolve this condition. If symptoms or DTCs return after all grounds are tightened, follow normal WSM diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2025-2026 Explorer/Aviator vehicles are no longer equipped with light emitting diode (LED) confirmation on the vehicles key fob indicating that the vehicle has remote started (or not remote started). Factory key fobs with remote start no longer contain an LED feedback indicator. Do not replace the key fob for this condition. This is a normal operating characteristic and no service action is necessary.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2021-2026 Explorer vehicles equipped with the 2.3L EcoBoost engine may require air conditioning (A/C) compressor belt removal for various reasons. The Workshop Manual (WSM), Section 303-05A Accessory Drive - 2.3L EcoBoost > Removal and Installation > Air Conditioning (A/C) Compressor Belt procedure has been revised to eliminate cutting the A/C compressor belt to remove it. Refer to the updated procedure to reuse the belt.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This TSB supersedes TSB 26-2035. Reason for update: update the Service Procedure to add figures 1, 2, 5 and 6 to clarify the ground location, update Steps (13-15, 21-22), and update the Parts list according to the type of vehicle variant and repair. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * "Steering Assist Fault Service Required" message displayed in the instrument panel cluster (IPC) * Reduced steering assist * Diagnostic trouble codes (DTCs) U3008:1B and/or U3009:1B stored in the power steering control module (PSCM) This may be due to the PSCM ground connections.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
Source components: ELECTRICAL SYSTEM · LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 20212026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. When referred to a specific clutch (A-F) test by a pinpoint test in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing, the Clutch Assembly tests have been updated with a hyperlink to the new Transmission Line Pressure Test - Pressure Vacuum Transducer (PVT) Is Available procedure in WSM, Section 307-01 > General Procedures. This procedure provides instructions to perform the FDRS Transmission Clutch Circuit Leak Test when applicable. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2021-2026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. The Workshop Manual (WSM) has been updated under Section 307-01 > Diagnosis and Testing to include this procedure. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes TSB 26-2059. Reason For Update: To add missing labor operations. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
Source components: FUEL/PROPULSION SYSTEM · POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2026 Explorer/Police Interceptor Utility/Aviator vehicles may exhibit a concern of inoperative, rattling, crackling and/or distorted sound from one or more speakers (but not all speakers). This may be due to other components located near the suspect speaker. Workshop Manual (WSM), Section 415-00 > Diagnosis and Testing > Pinpoint Test D (2020-2024 Explorer/Police Interceptor Utility, 2025-2026 Aviator) and Pinpoint Test E (2020-2024 Aviator, 2025-2026 Explorer/Police Interceptor Utility) have been updated with additional direction when isolating the cause of the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2477 to update the Labor Operation Descriptions. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Poor speaker sound quality (static, pop, crackle) while using Bluetooth audio Poor outbound phone call sound quality while using Bluetooth This may be due to the APIM (accessory protocol interface module) software.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2024 Explorer vehicles equipped with a 2.3L engine and 2020-2026 Explorer/Police Interceptor Utility/Aviator vehicles equipped with a 3.0/3.3L engine may require various repairs associated with the fuel tank and/or fuel pump and sender unit. Workshop Manual (WSM), Section 310-00 > Removal and Installation for the fuel tank and fuel pump and sender unit have been revised to eliminate the need to remove the driveshaft as part of the service procedure. Labor times have also been updated to reflect this WSM revision.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes TSB 25-2423. Reason For Update: Replace the incorrect acronym SOWC with the correct acronym OWC. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 F-150, Expedition/Navigator, Escape/Corsair, Bronco, Explorer, Mustang, Maverick vehicles equipped with a 1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and/or may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the high-pressure fuel pump causing fuel to enter the crankcase and reduce fuel pressure in the direct injection fuel rail. Diagnose this condition using Pinpoint Test HP located in Workshop Manual (WSM), Section 303-04. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. Repair as necessary outside of this article. For claiming, if high-pressure fuel pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article.
Source components: ENGINE · FUEL/PROPULSION SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 20172026 vehicles equipped with a 10R transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024 Nautilus and 2025 Explorer vehicles equipped with the Google Maps Navigation System (minor feature code HKCGA) may experience a blank/white Google map screen, inoperative live traffic data, inoperative voice assistant, the inability to sign into a Google account in the center touch screen, unable to access the Google Play Store in the center display screen, and/or inability to connect to other apps in the center display screen. This may be due to the vehicles Connectivity Package not being activated. To verify if the vehicle has an active Connectivity Package (free or paid) enter the vehicle identification number (VIN) in Professional Technician System (PTS) then navigate to the upper blue tab titled Connected Vehicle > Vehicle Software Subscriptions. It will clearly state if the vehicle has a trial or paid subscription, along with the expiration date. These vehicles come with a free Connectivity Package that lasts for 1 year. To activate the free trial period or to subscribe to a paid subscription, have the customer follow the steps located within The Ford/Lincon App and follow the prompts
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2026 Nautilus and 2025-2026 Explorer/Aviator vehicles equipped with power folding mirrors may exhibit concerns with the auto folding mirror functionality not matching the status selected by the switch in the center display screen menu. Examples include auto folding not operating when the switch is enabled and/or auto folding continuing to function when the switch is disabled. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). Power folding mirror operation from the physical button is not affected by this condition. Inform customers that engineering is currently working on a solution for this condition that is expected in Q4 2026. Replacement or reprogramming of the accessory protocol interface module (APIM), DDM, or PDM will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.<br /><br /> If the vehicle exhibits this condition, submit a Vehicle Concern Report. To submit a report, click on the "Submit Global Concern Report"
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit a media bin that will not open consistently. This may be due to lack of tension between the media bin door and media pads.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles listed in the Model statement above may exhibit a no crank/no start condition where the customer cannot start their vehicle. The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.
Source components: ELECTRICAL SYSTEM · POWER TRAIN · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
All 2024-2025 Nautilus and 2025 Explorer/Aviator/Expedition/Navigator vehicles will have the Alexa Built-In feature removed from the vehicle in Q1 2026 due to the end of life of Amazon Alexa services in all Ford/Lincoln Digital Experience vehicles. Google Assistant will continue to be the default voice assistant in these vehicles. No additional actions should be taken in an attempt to restore Alexa Built-In functionality.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This TSB supersedes TSB 25-2350 to update the Service Procedure, vehicles affected, and parts list. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * "Steering Assist Fault Service Required" message displayed in the instrument panel cluster (IPC) * Reduced steering assist * Diagnostic trouble codes (DTCs) U3008:1B and/or U3009:1B stored in the power steering control module (PSCM) This may be due to the PSCM ground connections.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Explorer vehicles equipped with a 2.3L EcoBoost engine built on or after 16-Aug-2025 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0335 stored in the powertrain control module (PCM). DTC P033F may also be stored in the PCM. This may be due to a pin fit concern at PCM connector C1381E pin 7. To correct this condition, install a new terminal in wiring harness connector C1381E pin 7 (GN/BN) using terminal repair kit DU2Z-14474-CA. Refer to Wiring Diagram, Cell 5 for wiring repair information. For claiming use causal part 12A581 and labor operations 12650D and 12650D45WR.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2026 Nautilus, 2025-2026 Explorer/Aviator and 2025 Expedition/Navigator vehicles may exhibit a concern where during an inbound phone call using CarPlay®, the person in the vehicle cannot be heard. This may be due to the software in the accessory protocol interface module (APIM). Replacement or reprogramming of the APIM will not resolve this condition. Inform customers that engineering is currently working on a software solution for this condition and will be released via a software update delivered over-the-air (OTA) expected by April 2026. The software will update automatically if vehicle connectivity is enabled in the vehicle settings. Schedule a service visit for customers who have disabled vehicle connectivity or who report that they did not receive the update by May 2026. Monitor Professional Technician System (PTS) for additional information.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2026 Police Interceptor Utility vehicles may require level III ballistic panels to be replaced due to broken mounting tabs. Individual level III ballistic panel mounting tab service parts are now available: right-hand (78201B68) and left-hand (78201B69). Replacement of the level III ballistic panel assembly is not required for this condition. Level IV ballistic panels do not have removable mounting tabs and still require complete panel replacement. Level III vs level IV ballistic panels can be identified by a large roman numeral label on the panel or by the vehicle window sticker if equipped.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Expedition/Navigator/Explorer/Aviator and 2024-2026 Nautilus vehicles equipped with the Google Maps Navigation System (minor feature code HKCGA) may experience a blank screen for Google Maps or the absence of live traffic data. To correct this condition, refer to the Workshop Manual (WSM), Section 415-00 > Diagnosis and Testing > Information and Entertainment System. The WSM has been updated with improved diagnostics for this condition. To confirm whether a vehicle is built with a specific minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner of the Professional Technician System (PTS).
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Program 25N19 Certain 2024-2026 Model Year Corsair and Certain 2025-2026 Model Year Explorer and Aviator Vehicles Windshield Replacement
Source components: UNKNOWN OR OTHER · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit steering column shrouds that are misaligned or pushed out. This may be due to the wiring harness causing interference with the upper and lower shroud connection. Additional Model specification: Equipped with BlueCruise hands free driving system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Aviator/Explorer/Police Interceptor Utility vehicles may exhibit diagnostic trouble code (DTC) C1110:56 and/or U3000:96 stored in the power steering control module (PSCM) after programming the PSCM, or may display the following message in Ford Diagnosis and Repair System (FDRS) when performing PSCM programmable module installation (PMI): <br /><br /> "It has been detected that a Model Year 2025 Steering Gear (R1MC - level) is fitted to this vehicle. It is not possible to run the Power Steering Control Module (PSCM) Programmable Module Installation (PMI) application on this Steering Gear. If later software is available, this PSCM can be updated by running the PSCM Software Update application."<br /><br /> This may be due to the calibration in the PSCM. When installing a replacement steering gear, make sure the part number begins with prefix "S1MZ". If DTC U3000:96 previously set after programming the PSCM, continue with normal diagnostics outside this article. Refer to Workshop Manual (WSM), Section 211-02 > Diagnosis and Testing. Improvements have been made to the diagnostics for this DTC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2025 various Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
Source components: ELECTRICAL SYSTEM · LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Program 25B52 Certain 2025 Model Year Explorer and Aviator Missing Audio Tile – Accessory Protocol Interface Module Software Update
NHTSA source summary · Original PDF not reviewed by Recallfolio
Quality improvements include: -Addresses a false positive Diagnostic Trouble Code due to high sensitivity that may cause a hard brake pedal and some lamps in the cluster. Issue gets resolved in the next key cycle -Addresses key off load battery usage caused by the Electric brake boost stsying active
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Poor speaker sound quality (static, pop, crackle) while using Bluetooth audio Poor outbound phone call sound quality while using Bluetooth This may be due to the APIM (accessory protocol interface module) software.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Explorer vehicles equipped with a 2.3L EcoBoost engine may require various repairs and/or maintenance on the fuel system. This may require removal of the high-pressure fuel injectors, high pressure fuel pump, and/or fuel tank/sender. The applicable Workshop Manual (WSM) Sections 310-00 and 303-04 have been revised to reflect updated replacement service procedure steps for these components. Some component removal steps were eliminated from the service procedures and service labor times adjusted to reflect the latest WSM updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Explorer/Aviator vehicles may exhibit a condition where the instrument panel cluster (IPC) displays an unexpected Watch the Road warning while using BlueCruise with no diagnostic trouble codes (DTCs) stored related to the driver-assist systems. This may be due to the steering column tilt angle and/or driver seat position (height and backrest angle). Replacing components is not expected to resolve this issue. Optimize driver head position by adjusting the steering column tilt angle and driver seat position (height and backrest angle) to ensure the driver status monitor camera (DSMC) mounted on top of the steering column has a clear view of the drivers entire face from chin to forehead. Provide both Explorer and Aviator customers with a printout of the Lincoln Aviator Owners Manual page titled, Lincoln BlueCruise > How Does BlueCruise Work. The Explorer Owner's Manual is in process of being updated. If the customers symptom persists after the above adjustments have been performed, continue with normal diagnostics found in the Workshop Manual (WSM), Section 419-03B.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit a "Front Camera Fault Service Required" message appearing in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) C1001:31 setting in the image processing module A (IPMA). This may be due to a loose or partial connection at the front windshield camera, connector C9449 on Explorer/Police Interceptor Utility and C9128 on Aviator. Check and verify this connection prior to starting Workshop Manual (WSM) Pinpoint Tests. If the connection is secure, continue with normal diagnostics.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 Nautilus and 2025 Explorer/Aviator/Expedition/Navigator vehicles equipped with Ford/Lincoln Digital Experience may exhibit a "Map Source Not Available" message on the instrument panel cluster display (IPC) when using Google Maps via Apple CarPlay®. Google Maps does not yet support displaying the navigation map on the IPC within the Apple CarPlay® environment and this is currently the expected behavior. Replacing or reprogramming the accessory protocol interface module (APIM) will not resolve this condition and no diagnosis or repair is necessary. Inform the customer that a future Google Maps update for iPhone is anticipated to enable this functionality. This update will be delivered directly through the Google Maps app on their iPhone and will not require an over the air (OTA) software update or dealership visit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2283 to add production cutoff dates. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Inbound call cannot be heard Wireless charger icon inaccurate Auto hold, auto start-stop, and/or defrost button LED indicators inoperative This may be due to the accessory protocol interface module (APIM) software.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER · VEHICLE SPEED CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2023-2025 Explorer (rear windows only), Bronco Sport, Escape, and Maverick vehicles equipped with minor feature code B2DAC may exhibit an inoperative passenger front and/or rear window switch. To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle Information or double-clicking the vehicle identification number (VIN) in the upper left corner of Professional Technician System (PTS). This may be due to an open diode in one of the passenger window switches. To correct the condition, replace the passenger window switch of the affected window. If the condition persists continue with normal diagnostics. Refer to Workshop Manual, Section 501-11. For claiming, use causal part 14529 and labor operation 14529A in the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Harvest Program 25H03 Certain 2024 - 2025 Model Year Bronco, Bronco Sport, Corsair, Escape, Explorer, Maverick, Mustang, and Ranger Vehicles with 1.5L, 2.0L, or 2.3L Engine Spark Plug Replacemen
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2361 to update the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit oil consumption and blue smoke from the tailpipe. This may be due to the sealing process of the PCV baffle which is part of the valve cover assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2024 - 2025 Model Year Bronco, Bronco Sport, Corsair, Escape, Explorer, Maverick, Mustang, and Ranger Vehicles with 1.5L, 2.0L, or 2.3L Engine Spark Plug Replacement
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 F-150, Expedition/Navigator, Escape/Corsair, Bronco, Explorer, Mustang, Maverick vehicles equipped with a 1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the fuel injection pump causing fuel to enter the crankcase and reduce fuel pressure in the high pressure fuel rail. Diagnose this condition using Pinpoint Test HP located in the Workshop Manual, Section 303-04A. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. For claiming, if fuel injection pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article. Note: Components damaged as a result of this failure mode
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2021-2025 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit "Please Check Surroundings For Safety" or "Full View Not Available" messages when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.
Source components: UNKNOWN OR OTHER · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2294 to update the vehicle lines affected. Some of the vehicles listed in the Model statement above may exhibit driver assistance feature warning messages displayed in the instrument panel cluster (IPC). Additionally, some modules may store invalid data/lost communication diagnostic trouble codes (DTCs). This may be due to software in the image processing module A (IPMA).
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit oil consumption and blue smoke from the tailpipe. This may be due to the sealing process of the PCV baffle which is part of the valve cover assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Ford and Lincoln vehicles equipped with SYNC4/Digital Experience may exhibit an unsuccessful telematics control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2025 Model Year Bronco, Explorer, Mustang, and Ranger Vehicles Engine Coolant Temperature Sensor Replacement On all affected vehicles, the Engine Coolant Temperature sensor (ECT) may have a poor solder joint internally, causing a Diagnostic Trouble Code (DTC) to set against the sensor for an open circuit and the check engine light to illuminate
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * "Steering Assist Fault Service Required" message displayed in the instrument panel cluster (IPC) * Reduced steering assist * Diagnostic trouble codes (DTCs) U3008 and/or U3009 stored in the power steering control module (PSCM) This may be due to the PSCM ground connections.