2020 Ford EXPLORER Manufacturer communications & TSBs.Page 4
Original record summaries, dates and identifiers for this model-year. Records 301–360 of 360, ordered newest first. Dated records on this page: Aug 9, 2019–Sep 22, 2020.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Sep 22, 2020Service Bulletin/Repair Instructions
SSM 49197
NHTSA communication ID: 10180407
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a hybrid engine and built on or before 04-Aug-2020 may exhibit an illuminated malfunction indicator lamp (MIL) and/or engine overheating fault message with diagnostic trouble codes (DTCs) P0217 and/or P06EF stored in the powertrain control module (PCM). This may be due to an assembly pin left in the accessory drive belt tensioner during the production process. To correct the condition, remove any assembly pins from the accessory drive belt tensioner. If no pins are found, refer to Workshop Manual (WSM), Section 303-06 or Section 303-03 for further diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer vehicles may exhibit loose fitting side trim panels on the front row lower seat cushions and upper seat backs. This may cause the seat cover to appear to be cut improperly. The seat cover should not be replaced for this concern. Adjust the seat side trim panels for proper fit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Police Interceptor vehicles built on or before 24-Jul-2020 may exhibit a front door lock cylinder that is difficult to turn with the key. This may be caused by the lock pawl in the front door latch. To correct the condition, revised front door latches LB5Z-78219A65-F (left) and LB5Z-78219A64-F (right) have been released for service. Use Rotunda key part number 164-R0479 in conjunction with the updated front door latches.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In some of the affected vehicles, a leak in the transmission oil cooler may occur due to a crack developing near the oil cooler line fittings. Loss of transmission fluid could lead to transmission noise, harsh shifts or the inability to shift out of park.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles built on 07-Nov-2019 and through 04-Aug-2020 may exhibit a lack of power steering assist at initial engine start-up with diagnostic trouble code (DTC) C102D stored in the power steering control module (PCSM). This may be due to the software in the PCSM. During normal diagnostics in Workshop Manual (WSM), Section 211-02, if pinpoint test (PPT) step AI5 is answered YES, reprogram the PCSM with the latest software level of the appropriate Ford diagnostic scan tool. If DTC C102D returns, continue with normal diagnostics. For claiming, use causal part 3504 and applicable labor operations in Sections 03 and 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 MKZ, 2019-2020 Mustang/Continental/Fusion/F-150/Transit Connect/ Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/ Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Escape and Explorer hybrid vehicles may experience discharge of the high voltage battery (HVB) with DTCs P0DE6 and P0A7D. This may be due to the vehicle not being operated for an extended length of time or from a crank/no-start condition. If the HVB is discharged, refer to the applicable GSB and Workshop Manual section to confirm if off-board charging is required. Note that the voltages in the GSB do not apply to 2020 Escape and Explorer. Using the appropriate Ford scan tool, monitor PID values: HVBAT_V on 2020 Escape (at least 90V, but less than 165V)and 2020 Explorer HVBAT_V (at least 114V, but less than 210V). For both vehicles, HEV_BAT_MIN_V should be greater than 1.45V, and HEV_BAT_VAR_V less than 2.5V. If the values are within limits and the HVB is suitable for a rescue charge, contact the Technical Assistance Center to request a high voltage charger.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles may display a distance to empty value in the instrument panel cluster (IPC) that does not correctly represent the actual fuel level of the vehicle. This may be due to excessive idling and/or a learned value in the powertrain control module (PCM) that is incorrect. To correct the condition, perform the PCM - Reset the Keep Alive Memory (KAM) application in the appropriate Ford diagnostic scan tool. For claiming, use Causal Part 12A650 and applicable labor times from Section 10 in the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM:INSTRUMENT PANEL:FUEL GAUGE:FUEL LEVEL FLOAT/SENSOR/SENDING UNIT · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 20-2107 to update the Part List. Some 2020 Explorer/Aviator vehicles built on or before 19-May-2020 and equipped with a 10R60 automatic transmission may exhibit a harsh 7-6 gear downshift. This may be caused by the A clutch piston return spring snap ring becoming dislodged. To correct the condition, follow the Service Procedure steps to replace the front support and A clutch assemblies.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a 3.0L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P062C or P179D stored in the powertrain control module (PCM) and a possible lack of power. This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM.
Source components: ELECTRICAL SYSTEM:SOFTWARE · ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 20-2135 to correct the Service Procedure. Some 2020 Explorer/Aviator/Corsair vehicles built on or before 23-Jul-2020 may inadvertently activate the reverse braking assist system while backing up. This may be perceived as the system is too sensitive to surrounding objects. This may be due to the software in the image processing module B (IPMB). To correct the condition, follow the Service Procedure to reprogram the IPMB, as well as the accessory protocol interface module (APIM) to allow the vehicle to remember the last setting of reverse brake assist when the vehicle is restarted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Police Interceptor Utility vehicles equipped with SYNC built on or before 30-Aug-2019 may exhibit a discharged battery/no crank condition. This may be caused by the software in the accessory protocol interface module (APIM), body control module (BCM) and/or the telematics control unit (TCU) module. To correct the condition, reprogram the APIM, BCM, and the TCU using the latest software level of the appropriate Ford diagnostic scan tool. The SYNC 3 universal thumb drive should not be used to correct this condition. If the battery drain concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 414-01 > General Procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles may exhibit a rattle type noise originating from the exhaust flexible pipe. This may be due to the natural harmonic frequency of the pipe. To correct the condition, follow the Service Procedure to install a worm gear clamp over the exhaust flexible pipe.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles built on or before 04-Sep-2019 equipped with memory seats may exhibit the driver front seat moving forward during easy entry/exit operation when the vehicle is turned off. This may be due to the software in the driver front seat module (DSM). To correct the condition, reprogram the DSM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14C708 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine may appear to have low engine oil level if the proper procedures are not followed. Refer to the Owners Guide, Maintenance, Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Ford and Lincoln vehicles equipped with a TCU may exhibit incomplete user authorization, no authorization pop-up on the SYNC infotainment system, vehicle connectivity concerns, vehicle location disabled message and/or various FordPass/LincolnWay App command/control concerns. To correct these conditions, ensure that customer connectivity settings (CCS) are turned on in the SYNC system. If the concerns persist after CCS is turned on, turn CCS OFF, perform an ignition cycle, and turn CCS settings back on. After any CCS changes, force-close and relaunch the FordPass/ LincolnWay app on the customers phone. Once CCS is turned on, program the TCU to the latest IDS/FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
Source components: ELECTRICAL SYSTEM · ENGINE · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app , incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 MKZ, 2019-2020 Mustang/Continental/Fusion/F-150/Transit Connect/ Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/ Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Ford and Lincoln vehicles equipped with SYNC 3 may not be able to properly disable remote start through the SYNC interface. This may be due to the current level SYNC software installed. To correct this condition, program the SYNC module. Refer to Workshop Manual (WSM), Section 415-00. If no update is available or the condition persists after programming, refer to WSM, Section 303-06 for further diagnosis. The remote start can be disabled in one of three methods: (1) leaving the hood open, (2) de-activation through the SYNC System Customer Preferences (refer to SYNC settings in the Owner's Manual), or (3) disconnecting the 12 Volt Battery. Refer to WSM, Section 100-00 for further information on remote start disabling.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer vehicles built on or before 01-Dec-2019 may exhibit heating, ventilation and air conditioning (HVAC) airflow or temperature not operating as commanded. This may be perceived as a lack of airflow from various vents or inconsistent temperature from side to side. This may be due to the software in the HVAC module. To correct the condition, reprogram the HVAC module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 19980 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer vehicles equipped with a 2.3L EcoBoost/3.3L Duratec engine and a rotary gear shift knob built on or before 14-Jul-2020 may exhibit slow fuel fill, premature fuel nozzle shut off, and/or spit back during refueling with no diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM). This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM.
Source components: ELECTRICAL SYSTEM · FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles equipped with all-wheel drive (AWD) and built on or before 15-Jul-2020 may exhibit various warning/fault indicators with diagnostic trouble codes (DTCs) C006A:74 and/or P166E stored in the AWD module and/or U0102 stored in the anti-lock brake system (ABS) module. This may be due to the software in the AWD module. To correct the condition, reprogram the AWD module with the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 7P238 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Police Interceptor Utility vehicles equipped with a 3.3L Hybrid engine and built on or before 17-Jul-2020 may exhibit a harsh shift, a harsh engagement to DRIVE and/or REVERSE and/or a buck/jerk/hesitation condition at low speeds with no diagnostic trouble codes stored in the powertrain control module (PCM). This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles built on or before 15Jul-2020 may exhibit a perceived soft/low brake pedal at initial vehicle start up with diagnostic trouble code (DTC) C0047:64 stored in the anti-lock brake system (ABS) module. The vehicle may also exhibit an illuminated ABS, Advance Trac, and/or red brake warning lamp, and possible Advance Trac Fault message displayed. This may be due to the software in the ABS module. To correct the condition, reprogram the ABS module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 2005 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM:SOFTWARE · ENGINE · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer vehicles equipped with a 2.3L EcoBoost engine built on or before 14-Jul-2020 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0299. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Police Interceptor Utility vehicles built on or before 21-Apr-2020 may exhibit inoperative manual rear door locks. This may be due to the manual rear door lock cable becoming dislodged from the rear door. To correct the condition, follow the Service Procedure steps to apply adhesive to the manual rear door lock cable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Corsair/Explorer/Super Duty vehicles built on or before 27-May-2020 and not equipped with a 360-camera system may exhibit various rear parking aid camera concerns such as poor image quality, flickering and/or completely inoperative. If a vehicle exhibits any of these conditions, replace the rear parking aid camera. Refer to Workshop Manual (WSM), Section 413-13. For claiming, use causal part 19G490 and any applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles built on or before 17-Feb-2020 may exhibit an intermittent partial opening of the power liftgate and/or false activation of the anti-theft alarm with diagnostic trouble codes (DTCs) B144D, B144E, B1555 and/or B1556 stored in the rear gate trunk module (RGTM). This may be due to the software in the RGTM improperly sensing that the liftgate is ajar. To correct the condition, reprogram the RGTM with the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · LATCHES/LOCKS/LINKAGES:TAILGATE:LATCH.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles built on or before 13-Dec-2019 may exhibit a hard brake pedal or reduced pedal travel when the transmission is initially placed in gear with no diagnostic trouble codes (DTCs) stored in the anti-lock brake system (ABS) module. This condition only occurs at initial vehicle start-up and will no longer be present after the brake pedal is released and re-applied during the same key cycle. This is not a lack of power brake assist. This may be caused by the software in the ABS module. To correct the condition, reprogram the ABS module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 2005 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) and/or Engine Coolant Over Temperature warning with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0128, P0217, P0330, P1026, P1299, and/or P130D. This may be due to the engine coolant temperature (ECT) sensor or ECT sensor wiring harness. To correct the condition, replace the ECT and knock sensor. To aid with the engineering investigation, do not disconnect the wiring connector from the ECT sensor during disassembly. Leave the connector on the sensor in case parts are called back for analysis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles built on or before 19-May-2020 and equipped with a 10R60 automatic transmission may exhibit a harsh 7-6 gear downshift. This may be caused by the A clutch piston return spring snap ring becoming dislodged. To correct the condition, follow the Service Procedure steps to replace the front support and A clutch assemblies.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer vehicles equipped with a 2.3L EcoBoost engine and built on or before 10-Jan-2020 may exhibit various transmission concerns requiring either disassembly and repair or complete transmission replacement. When performing transmission service, inspect the transmission oil cooler. If the cooler is not equipped with a support bracket fastened to the transmission bellhousing, replace the transmission oil cooler. Refer to TSB 20-2086 for part information and additional details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer PHEV vehicles built on or before 13-Dec-2019 may exhibit a hard brake pedal or reduced pedal travel when the transmission is initially placed in gear with no diagnostic trouble codes (DTCs) stored in the anti-lock brake system (ABS) module. This condition only occurs at initial vehicle start-up and will no longer be present after the brake pedal is released and re-applied during the same key cycle. This is not a lack of power brake assist. This may be caused by the software in the ABS module. To correct the condition, reprogram the ABS module using the latest software level of the appropriate Ford tool. Pls procced as the normal warranty procedure
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles may exhibit a perceived lack of power brake assist or extended brake pedal travel at initial vehicle start up with diagnostic trouble code (DTC) C0047:64 stored in the anti-lock brake system (ABS) module. The vehicle may also exhibit an illuminated ABS, Advance Trac, and/or red brake warning lamp, and possible Advance Trac Fault message displayed. This may be caused by the software in the ABS module. To correct the condition, reprogram the ABS module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 2005 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Police Interceptor vehicles built on or after 14-Nov-2019 may not be equipped with an installation point behind the front fascia to mount a front recovery hook. The installation point was deleted as a running change. The vehicle is not misbuilt. The addition of any parts would not be considered a warrantable repair. Do not submit a claim for this condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles built on or before 22-June-2020 may exhibit a Front Camera Fault message and/or Collision Warning Not Available message with diagnostic trouble code (DTC) U3000:49 stored in the image processing module A (IPMA). This may be due to the software in the IPMA. To correct the condition, reprogram the IPMA using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 19G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles may exhibit a rattle type noise originating from the exhaust flexible pipe. This may be due to the natural harmonic frequency of the pipe. To correct the condition, follow the Service Procedure to install a worm gear clamp over the exhaust flexible pipe.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer vehicles equipped with a 2.3L EcoBoost engine and built on or before 02-Dec-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P062C and/or P2243. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.
Source components: ELECTRICAL SYSTEM:SOFTWARE · ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Escape/Corsair/Explorer/Aviator vehicles may have diagnostic trouble code (DTC) U0100 stored in the audio front control module (ACM). This DTC will not cause observable conditions or warning indicators for the customer. If this DTC is detected during pre-delivery inspection (PDI) or while diagnosing unrelated conditions, it should be disregarded.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles may experience an intermittent or constant blank/black screen on the center infotainment display due the low voltage differential signaling (LVDS) cable at the SYNC accessory protocol interface module (APIM) not being fully seated. Verify that the connector is fully seated into the APIM prior to performing any other diagnostics or repairs on the vehicle for this concern. If the connection is found loose, re-seat the connection and retest. If the LVDS cable is found not to be the cause of the blank screen, follow Workshop Manual section 415-00 for further diagnosis. For claiming, use causal part number 10E929 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Police Interceptor Utility vehicles that had dark car mode enabled or disabled with FDRS on or before 21-May-2020 may have inadvertently had the remote keyless entry (RKE) transmitters disabled. To correct the condition, reprogram the RKE transmitters with FDRS application BCM - Remote Keyless Entry (RKE) Transmitter Programming. For claiming, use causal part 15607 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer vehicles equipped with a leather wrapped steering wheel may exhibit the leather covering becoming untucked or separating from the steering wheel. The leather may be able to be re-adhered to the steering wheel. Steering wheel replacement may not be necessary. Refer to Workshop Manual (WSM), Section 211-04 Steering Column > General Procedures > Steering Wheel Cover Repair for the updated repair procedure. It is not necessary to remove the steering wheel to perform this procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the infotainment system stating in Michigan when trying to select a point of interest using the push to talk feature on the navigation system. Engineering is currently working on a solution for this condition, which is expected to be available in July. Please monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Ford and Lincoln vehicles may exhibit a symptom of no ability to schedule a remote start event using the FordPass or Lincolnway app. If only the scheduling portion of the remote start system is not functioning, please ensure that the latest level of SYNC software has been installed. If the remote start system is not functioning using the key fob and/or the on-demand remote start function from FordPass or Lincolnway application, refer to Workshop Manual (WSM), Section 303-06 for further diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit a Front Camera Fault message and/or Collision Warning Not Available message with diagnostic trouble code (DTC) U3000:49 stored in the image processing module A (IPMA). This may be due to the software in the IPMA. To correct the condition, reprogram the IPMA using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 19G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 Model year vehicles equipped with 3.3L, 3.5L EcoBoost, or 5.0L engines may exhibit stalling, lack of power, low fuel rail pressure and/or DTCs P0087 or P008A after a repair was made that required the removal of the fuel line that connects the high-pressure fuel pump to the port injection rail, such as injector replacements or base engine repairs. This line must be installed in the correct orientation as it has an internal one-way check valve. To determine if the fuel line has been installed improperly, look at the position of the Oetiker clamp (stainless band clamped around the black fuel line). The clamp holds the one-way check valve in place and should be located closest to the end connected to the port injection rail. If the clamp is not closest to the port injection rail, remove and reinstall the line in the proper orientation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Escape/Aviator/Explorer Hybrid vehicles and 2020 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine may exhibit slow fuel fill, premature shut off, and/or spit back during refueling. This may be due to the interface between the fuel nozzle and the fuel tank filler pipe. When refueling, advise customers to make sure to rotate the fuel nozzle 30 degrees in either direction, retract the fuel nozzle slightly within the capless filler inlet, and/or use a different refueling pump. Engineering is currently working on a solution for this condition, which is expected to be available in the fourth quarter of 2020. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a 10R80 MHT automatic transmission and with less than 100 miles may exhibit a transmission fluid leak that appears to be coming from between the hybrid drive unit and transmission case joint. This condition may be due to residual transmission fluid trapped between the front module and transmission case joint during the assembly process. Recommend cleaning the area thoroughly and reevaluating with the vehicle at operating temperature before attempting any leak related repairs.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the affected vehicles may be stuck in low gear after first staring the engine, the transmission may exhibit harsh shifting and hesitation. As a customer continues to drive, the vehicle may default to fourth gear. An illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P062C and/or P2243 may be present in memory.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Escape/Corsair, Edge, Explorer, Fusion, Ranger, Transit Connect Vehicles equipped with a TCU may exhibit a "Battery Backup Component Failure" message in the cluster. This may be accompanied by DTC 1477-09 - Backup Battery Component Failure. This may be due to the TCU experiencing a sudden temperature change. To correct this condition, reprogram the TCU using the appropriate Ford diagnostic scan tool. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer, Aviator, Ecosport, Mustang, Escape or Corsair may have a symptom of no ability to schedule a remote start event using the Fordpass or Lincolnway app. This may be due to the current level SYNC software installed. To correct this condition, program the SYNC module utilizing section 415 of the workshop manual. If no update is available or the problem persists after programming, verify that the Fordpass or Lincolnway app is activated properly as per the owners guide. For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Expedition/Navigator, 2019 Edge/Nautilus, 2020 Explorer/Aviator vehicles equipped with a family entertainment system may experience an issue where the audio not synchronized with the video display when using the vehicle speakers. To correct this condition, contact the VOXX Customer Service Department at 1-866-869-7888. For claiming, refer to the Warranty and Policy manual for Ford Licensed Accessories.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NEW VEHICLE DEMONSTRATION / DELIVERY HOLD Customer Satisfaction Program 19B28 Certain 2020 Model Year Explorer ST Vehicles - Shipped w/o Performance Brake Package
NHTSA source summary · Original PDF not reviewed by Recallfolio
NEW VEHICLE DELIVERY HOLD - Customer Satisfaction Program 19B24 Certain 2019 Model Year Ranger and 2020 Model Year Explorer Vehicles with 2.3L EcoBoost Engines Balance Shaft and Oil Pump Assembly Inspection
NHTSA source summary · Original PDF not reviewed by Recallfolio
Advance Notice NEW VEHICLE DELIVERY HOLD - Customer Satisfaction Program 19B24: Certain 2019 Model Year Ranger and 2020 Model Year Explorer Vehicles with 2.3L EcoBoost Engines - Balance Shaft and Oil Pump Assembly Inspection
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.