2020 Ford EXPLORER Manufacturer communications & TSBs.Page 3
Original record summaries, dates and identifiers for this model-year. Records 201–300 of 360, ordered newest first. Dated records on this page: Sep 23, 2020–Feb 17, 2022.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Feb 17, 2022Service Bulletin/Repair Instructions
SSM 50502
NHTSA communication ID: 10208146
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Focus/MKX/C-MAX, 2017-2019 MKC/Taurus/Flex/MKT, 2017-2020 Fusion/MKZ/Continental, 2017-2022 Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Police Interceptor Utility vehicles equipped with 3.3L hybrid engine may exhibit delayed acceleration response, hesitation and/or a buck/jerk condition at low vehicle speeds with no diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM). The customer may perceive this as a delayed throttle response or lack of power. This may be more noticeable when switching between braking and acceleration. This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with the 2.3L engine may exhibit a red brake warning lamp and/or brake system warning message in the instrument panel cluster (IPC) with a diagnostic trouble code (DTC) P050F in the anti-lock brake system (ABS) module and a firm brake pedal. This may be due to contamination in a brake booster vacuum line. To correct this condition, replace the vehicle's vacuum hose (MB3Z-2420-A). Refer to Workshop Manual (WSM), Section 206-09 for installation instructions. For claiming, use casual part 2420.
Source components: SERVICE BRAKES, HYDRAULIC · SERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM:HOSES, LINES/PIPING, AND FITTINGS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer vehicles may exhibit a rear axle mounting bolt that has broken. In order to correct the condition, the rear subframe, differential cover, and mounting bolts will need to be replaced in addition to any other damaged components. Inspect the halfshafts, drive shaft, and differential for any damage, replacing damaged components as necessary. Refer to Workshop Manual (WSM), Section 502-00 for removal of the subframe. Once the subframe is removed from the vehicle, remove and install any replacement components to the new subframe. Refer to WSM, Section 205-02. For claiming, use causal part 4001.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator/Escape/Corsair, 2021-2022 Bronco Sport, and 2022 Maverick vehicles may exhibit an inoperative driver door window control switch (windows inoperative, mirror control unresponsive, etc.). Diagnostic trouble code (DTC) B1088:87 may be present in the driver door module (DDM). This may be due to the software in the DDM. To correct the condition, reprogram the DDM with the latest software level of the Ford Diagnosis and Repair System (FDRS). After reprogramming the DDM, run the DDM configuration application and perform a window learn routine via FDRS. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING:SWITCHES/KNOBS/BUTTONS · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit a wind/whistle type noise at highway speeds originating from the front A-pillar applique (either side or both). This may be due to a small gap between the outboard side of the A-pillar applique and the moulding. To correct the condition, follow the Service Procedure to install thin strips of flock tape on the A-pillar applique.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit a driveline vibration. Workshop Manual (WSM) Pinpoint Tests G (driveline shudder) and H (driveline vibration) have been updated in WSM, Section 205-01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 F-Super Duty/Explorer/Aviator and 2021-2022 F-150 vehicles may exhibit a Front Camera Fault, Lane Keeping Fault, and/or Collison Warning Not Available message with various diagnostic trouble codes (DTC) stored in the image processing module A (IPMA). If programming fails or Ford Diagnosis and Repair System (FDRS) states a file failed to flash after replacing the IPMA or reprogramming IPMA software, test the battery using any approved Rotunda tool including the GR-190, GRX-3590, and DCA-8000. Fully recharge or replace the battery according to results of the tool. Set the battery charger to maintain battery voltage between 12.6 and 13.6 volts during the entire programming procedure. The IPMA programming procedure may take several hours to complete due to the size of the software files required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2022 Explorer and 2020-2022 Aviator vehicles may experience an inoperative roof opening panel motor. If diagnostics lead to a motor replacement, visually inspect the original motor for signs of water intrusion. If found, determine source of water leak prior to replacing the motor. Refer to Workshop Manual (WSM), Section 501-17, Pinpoint Test A for 2011-2016 and Pinpoint Test B for 2017-2022 for identifying the source of the water leak.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator/Police Interceptor Utility vehicles and 2021 F-150 vehicles equipped with a 10R80 MHT automatic transmission may exhibit a harsh/delayed engagement and/or a harsh/delayed shift with or without an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6, P07F7, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM). This may be due to sticking valves in the main control valve body. To correct the condition, follow the Service Procedure steps to perform the PCM - Transmission Accelerated Main Control Break In routine for the appropriate clutch(s) and/or overhaul the main control valve body.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer vehicles equipped with a 2.3L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04F0 and/or P144C stored in the powertrain control module (PCM). This may be due to loose or partially connected evaporative emissions (EVAP) vapor lines. To correct the condition, follow the Service Procedure to make sure the EVAP vapor lines are properly connected.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit poor sound quality from the left and/or right front speaker while using Bluetooth audio. This may be due to concerns with the wiring harness or connections of connector C2383A, C202, and/or C4240B. Prior to the replacement of the affected speaker, inspect the inline connections at connectors C2383A, C202, and C4240B for damage or incorrect pin fit. If no concerns are found with the wiring harness, continue with the replacement of the affected speaker.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit an illuminated MIL with multiple diagnostic trouble codes (DTC). These DTCs may include P04F0, P008A, P0451, P0455, P0456, P0496 and/or P018C. This may be due to the wiring harness connection at connector C1198. Prior to replacement of any components, inspect the connector and wiring harness for any damage or pin fit concerns. If any damage or pin fit concerns are found, repair the connector or harness as necessary. If no damage or pin fit concerns are found, refer to normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator/Police Interceptor Utility vehicles equipped with AWD may exhibit a binding or shudder sensation while turning and/or while accelerating from low speeds. The concern may also be described as a grinding and/or chatter noise. If the Workshop Manual (WSM) leads to replacement of the rear axle, inspect the differential for damage and differential fluid for metallic chunks in the fluid. Note that some metallic flake in the fluid and/or discoloration is normal and the rear axle should not be replaced for it. If no damage is found to the rear differential, it is not recommended to replace the rear axle assembly. Instead, refer to the Symptom Charts in WSM, Section 308-07 for further diagnosis of the transfer case.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 EcoSport, Expedition, Navigator; 2019-2021 Ranger; 2020-2021 Escape, Corsair, Explorer, Transit; 2021 Bronco, Bronco Sport, Edge, Nautilus, F-150, Mustang; 2019-2022 Transit Connect; 2020-2022 Aviator, F-Super Duty; and 2022 Maverick vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0496, P0456, P0455, P04F0, and/or P0451. Ford has tested returned EVAP canister purge valves and found them to be fully functional. Prior to replacing the canister purge valve or other EVAP components, perform the following tests using the Ford Diagnosis and Repair System (FDRS) Scan Tool: Full System EVAP Leak Test - FDRS Location: TOOLBOX > PCM > PCM - Evap Emissions System Test and the EVAP Purge Valve Leak Test - FDRS Location: TOOLBOX > PCM > Evap Emission System Toolbox > CPV Check.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2342 to update the Issue, Action, and Service Procedure. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns including but not limited to: Sirius audio not functioning properly after a key cycle with active subscription Presets not responding or indicating properly Intermittent audio echo/robotic voice heard during a Bluetooth phone call Wi-Fi connection message pop-up every key cycle Frozen unresponsive touchscreen Solid blue screen when moving forward at speeds above 16 km/h (10 mph) (2019 vehicles only) Rear parking aid camera remains on the screen at speeds below 16 km/h (10 mph) (2019 vehicles only) Inoperative infotainment applications Poor/no AppLink function Apple CarPlay not launching on connection or a black screen when connected Voice prompts that skip or have short pauses while directions are being provided
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: COMMUNICATION:MANUFACTURER TELEMATICS · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Escape/Corsair vehicles built on or before 30-Mar-2021 and Explorer/Aviator vehicles built on or before 09-Apr-2021 may exhibit a slow fuel fill and/or spit back condition during refueling. This may be due to the design of the fuel tank filler pipe. To correct the condition, follow the Service Procedure to replace the fuel tank filler pipe.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2021 Edge/Nautilus/Ranger, 2020-2021 Escape/Corsair/Explorer, and 2021 Bronco Sport vehicles equipped with a 2.0L/2.3L EcoBoost may exhibit a lack of power with an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P02AB, P0243, P0299, P1464, P25B3, P25B4, P2AB7, P2AB8 and/or P2AB9. This may be due to an inoperative wastegate actuator, missing wastegate actuator e-clip or non-visible damage to the actuator rod. A lower level service component has been released, K2GZ-9G488-B for Edge/Nautilus/Escape/Corsair/Bronco Sport vehicles and LB5Z-9G488-B for Explorer/Ranger vehicles, for service to replace the actuator, actuator rod and both e-clips. When replacing the wastegate actuator, it is important to replace all parts in the service kit. Turbocharger replacement is not necessary to correct the condition.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator Hybrids, 2021 Corsair Hybrid, 2021 F-150 PowerBoost, and 2021 Mustang Mach-E vehicles may exhibit a no-start with a Stop Safely Now warning message in the instrument panel cluster (IPC). The vehicle may have one or more of the following DTCs P0A23, P0A6F, P0A72, P0A75, P0A71, P0A74, P0A77, P0DFA, P06B1, P0A47, P1A0E set by the secondary on-board diagnostic module C (SOBDMC) or secondary on-board diagnostic module B (SOBDMB). This may be due to a drop in the 12-volt circuit. These DTCs will often occur at vehicle key-on and may be difficult to reproduce. Before replacement of the SOBDMC or SOBDMB, diagnose any low voltage DTCs (P0562, U3003) in other modules in the 12V system. If low voltage (less than 10V) is observed in these DTCs snapshot, diagnose the 12v system first. Refer to Workshop Manual (WSM), Section 418-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2046 to update the Issue, Action and Service Procedure. Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a 10R60/10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift with or without an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTCs) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6, P07F7, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM). This may be due to sticking valves in the main control valve body. To correct the condition, follow the Service Procedure steps to perform the PCM - Transmission Accelerated Main Control Break In routine for the appropriate clutch(s) and/or overhaul main control valve body.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator and 2021 Bronco vehicles may exhibit an illuminated airbag warning indicator with diagnostic trouble code (DTC) B1404:13 and/or B1407:13. This may be due to contamination and relative movement in the connection between the wiring harness and the side airbag. To correct the condition, follow the Service Procedure steps to replace the affected connector with a service pigtail and the affected side airbag.
Source components: AIR BAGS:SENSOR:SIDE IMPACT · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator vehicles may exhibit the A/C blowing warm air with DTC P0645 present in the heating ventilation and air conditioning (HVAC) module. This may be due to spread terminal/terminal pushout in wire harness 14290 and on the corresponding pins to the body control module C (BCMC). Before replacement of the BCMC, disconnect all connectors from the BCMC and check the BCMC pins and wire terminals for damage. Refer to Workshop Manual (WSM), Section 419-10. If spread terminals or terminal pushout is present, repair as necessary. Refer to Wiring Diagram, Cell 005 for repair procedures. Reconnect all connections to the BCMC as indicated by the procedure in the Shop manual. Test the function of the A/C to ensure that it is blowing cold air.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM) · POWER TRAIN:MANUAL TRANSMISSION:INTERNAL:DOGS/SYNCHROS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator hybrid vehicles may exhibit a brake pedal pulsation or vibration when the brakes are applied. The customer may state that the anti-locking brake system (ABS) system is activating without any indicators on the instrument panel cluster (IPC). This may be due to the regenerative braking software in the ABS module. To correct the condition, follow the Service Procedure Steps to perform a coordinated flash on the powertrain control module (PCM) and ABS module.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · SERVICE BRAKES, AIR:ANTILOCK:ABS WARNING LIGHT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2021 Ford and Lincoln vehicles equipped with 3.3L, 3.5L EcoBoost, or 5.0L engines may exhibit stalling, lack of power, low fuel rail pressure and/or DTCs P0087 or P008A after a repair was made that required the removal of the fuel line that connects the high-pressure fuel pump to the port injection rail, such as injector replacements or base engine repairs. This line must be installed in the correct orientation as it has an internal one-way check valve. To determine if the fuel line has been installed improperly, look at the position of the Oetiker clamp (stainless band clamped around the black fuel line). The clamp holds the one-way check valve in place and should be located closest to the end connected to the port injection rail. If the clamp is not closest to the port injection rail, remove and reinstall the line in the proper orientation.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator vehicles may exhibit an inoperative driver switchpack (windows inop, mirror control unresponsive, etc.). DTC B1088:87 may be present in the DDM. To correct the condition perform the Driver Door Module (DDM) configuration application using the Ford diagnostic scan tool. After running the configuration application, perform a window learn routine via the ford diagnostic scan tool. The condition can also be resolved by letting the vehicle enter a deep sleep cycle. Engineering is currently investigating this concern and will be releasing a service fix. Let the customer know they can continue to drive the vehicle and schedule service appointments for customers once the repair becomes available. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
Source components: SERVICE BRAKES, ELECTRIC:SOFTWARE/PROGRAMMING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator vehicles may exhibit an AutoHold System Fault message displayed in the IPC message center on vehicle start-up with no diagnostic trouble codes (DTCs) stored in the anti-lock brake system (ABS) module. This may be due to the software in the ABS module. To correct the condition, follow the Service Procedure steps to reprogram the powertrain control module (PCM) and/or ABS module using the latest software level of the appropriate Ford diagnostic scan tool.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2021 Ford and Lincoln vehicle customers may receive a message in their FordPass or Lincoln Way App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.
Source components: POWER TRAIN:MANUAL TRANSMISSION:INTERNAL:DOGS/SYNCHROS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 Ford/Lincoln vehicles equipped with a wireless charging pad may exhibit an inoperative charging pad, slow charging, a notification that the phone has been mispositioned on the charging pad and/or the phone charging icon in the center screen is not showing. This may be due to the customer's phone if they are using an iPhone 12. Vehicles equipped with a wireless charging pad are designed to charge best with phones that follow the Qi standard. The iPhone 12 hardware currently does not follow the Qi standard for wireless charging. This may make it difficult for Ford and Lincoln vehicles to wirelessly charge this specific phone. The phone can still be charged using the USB cable if the vehicle experiences the above symptoms. If the customer is using an iPhone 12, verify the wireless charging pad works with a Qi certified phone prior to any part replacements.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles equipped with all wheel drive (AWD) built on or before 20-Mar-2020 may exhibit various warning/fault messages with diagnostic trouble codes (DTCs) C0633 and/or C00A6:07 stored in the AWD module. This may be caused by an oil contaminated front halfshaft speed sensor. To correct the condition, follow the Service Procedure step to replace the front halfshaft speed sensor.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Ford and Lincoln vehicles are equipped with an anti-fogging feature known as enhanced windshield anti fogging strategy (EWAFS). This feature automatically adjusts airflow in the cabin to prevent the windshield from fogging up and may be perceived by customers as irregular climate control functionality. To reduce fogging, the EWAFS functions include: the air condition (A/C) button may turn on and off automatically, recirculated air may turn off automatically in all air modes except MAX A/C, recirculated air may also turn on and off automatically in various airflow modes in order to improve heating or cooling efficiency, and in auto climate control, high humidity conditions may automatically engage A/C compressor, increase blower motor speed and/or direct more air to windshield. Continue to monitor the Workshop Manual (WSM) for EWAFS updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit an inoperative cooling fan and/or a vehicle overheat message. This may be due to water intrusion into the cooling fan relay, a loose ground connection, or damaged wiring. Before replacement of the cooling fan assembly, perform Pinpoint Test KN. Also, locate the cooling fan relay and inspect for water intrusion or damage. The correct location of the cooling fan relay is in the front right portion of the engine bay. If the cooling fan relay is not in the correct location, check behind the front right wheel well in between the splash shield. If any water intrusion or damage is found to the relay, G103, or the connector C1048, replace and correctly mount the affected component as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator/Corsair vehicles may exhibit an intermittent blue screen on the center infotainment display for one or more cameras when the 360 degree camera view is activated. To correct the condition, reprogram the image processing module B (IPMB) using the latest software level of the appropriate Ford diagnostic scan tool. Once complete, perform the 360 degree camera alignment procedure. Refer to Workshop Manual (WSM), Section 413-13. For claiming, use causal part 19H405 and applicable labor operations in the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator/Corsair vehicles may experience seat pan looseness, lateral movement and/or clunk/thump noise on turns. To correct the condition, follow the Service Procedure steps to reinforce the cushion hook.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles built on or before 04-Sep-2019 equipped with memory seats may exhibit the driver front seat moving forward during easy entry/exit operation when the vehicle is turned off. This may be due to the software in the driver front seat module (DSM). To correct the condition, replace the DSM and reprogram the DSM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14C708 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 MKC, 2019-2021 Edge/Nautilus/Escape/Ranger/Explorer, 2020-2021 Corsair, and 2021 Bronco Sport vehicles equipped with 2.0L and 2.3L EcoBoost engines may exhibit a light to moderate ticking type noise at idle (600-700 RPM). The noise is usually more prominent in the area of the high-pressure fuel pump, located on the top of the engine just behind the number 4 ignition coil. This noise is not detrimental to engine function and has no short or long-term effects on engine durability. This an operating characteristic of these engines and no repairs should be attempted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Edge, 2016-2018 MKX, 2019-2021 Nautilus, 2018-2021 Expedition/Navigator, and 2020-2021 Escape/Corsair/Explorer/Aviator vehicles may exhibit an inoperative power liftgate. This may be due to the rear gate trunk module (RGTM) software. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2021 Ford and Lincoln vehicles may exhibit an intermittent audio echo/robotic voice heard during a bluetooth phone call by the person that is not in the vehicle. Using Apple CarPlay and Android Auto instead of Bluetooth can help alleviate the concern. Also turning on, then off, the privacy setting in the SYNC touchscreen can temporarily alleviate the concern. Engineering is currently investigating this concern and will be releasing a service fix in early July 2021. Let the customer know they can continue to drive the vehicle and schedule service appointments for customers once the repair becomes available. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit erratic shifting and/or a transmission fluid venting condition. If during the preliminary inspection the transmission fluid is found to be a foamy pink color this may indicate possible cross contamination of engine coolant and transmission fluid due to an internally leaking transmission fluid cooler assembly. When repairing or replacing the transmission assembly for an internally leaking transmission fluid cooler assembly, use causal part 7869 and applicable labor operations in Section 07 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer vehicles may exhibit a lack of heat from the passenger side of the vehicle when using the climate control. When diagnosing for insufficient, erratic or no heat from passenger side floor vents, first perform pinpoint test (PPT) K.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator Hybrid vehicles may exhibit a buzzing noise coming from the center console or cowl area with engine speed around 1500 RPM at idle or while driving. This may be due to the transmission park manual release cable vibrating against the transmission. This can be resolved by isolating the transmission park manual release cable with Rotunda PVC foam tape (164-R4901) or equivalent, where it is contacting the transmission. Replacement of the transmission park manual release cable is not necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ford Motor Company has determined certain 2020 Model Year Ford F-150, F-Super Duty and Explorer vehicles with a Ford factory-installed backup camera fail to conform to Federal Motor Vehicle Safety Standard number 111 - Rear Visibility. Contact your local Ford dealer to schedule a service date to perform the recall. Refer to the included communication from Ford for additional information. Altec is not able to complete this repair. All work must be completed by an authorized Ford dealer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2021 Ford and Lincoln vehicle owners may experience a condition of missing Authorization, Command and Control, Battery Charging Details or Phone-as-a-Key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, Utilize the FordPass Guides or Lincoln Way Concierge teams.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 Ford and Lincoln vehicles may not be able to perform remote commands via the FordPass/LincolnWay App due to an erroneous deep sleep message. If the vehicle has been driven within 14 days and the battery state of charge is above 9.5 volts when the deep sleep message set, this is an erroneous message. Starting and running the vehicle will clear the message and allow the remote commands to function again. Inform customers that engineering is currently working on a solution for this condition that will be released via an over the air (OTA) update that is expected in June 2021. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM) will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 vehicles supported by FDRS may not list a software update for a module under the SW Updates tab although an SSM or TSB is published for a software update. This may be due to the module already being at the latest software level. A later software level may have been programmed at the assembly plant, during a previous dealer visit or by an over the air (OTA) update for vehicles that have automatic updates enabled in the SYNC system settings. To review a vehicle's OTA update history, visit the Connected Vehicle > OTA Dashboard tab in OASIS. Information about the OTA Dashboard can be found on FMCDealer.com when performing a search on OTA History Job Aid.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator/Police Interceptor Utility and 2021 F-150 Hybrid vehicles equipped with a 10R80 modular hybrid transmission (MHT) and with less than 100 miles (160 kilometers) may exhibit a transmission fluid leak that appears to be coming from between the hybrid drive unit and transmission case joint. This condition may be due to residual transmission fluid trapped between the front module and transmission case joint during the assembly process. Clean the area thoroughly and reevaluate with the vehicle at operating temperature before attempting any leak related repairs.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a 10R60/10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift with or without an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTCs) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6, P07F7, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM). This may be due to sticking valves in the main control valve body. Most vehicles will improve and no longer exhibit the condition after the first 8,000 km (5,000 mi) of driving. To correct the condition, follow the Service Procedure steps to perform the PCM - Transmission Accelerated Main Control Break In routine for the appropriate clutch(s) and/or overhaul main control valve body.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 F-150/F-Super Duty/Expedition/Navigator and 2020 Explorer/Aviator vehicles may exhibit a 'Trailer Connected' or 'Trailer Disconnected' message in the vehicle's message center with no trailer attached to the vehicle. To address this condition, reprogram the trailer module (TRM) using the appropriate Ford diagnostic scan tool. For claiming use causal part 19H332 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator Hybrid vehicles may exhibit a buzzing noise coming from the center console or cowl area with engine speed around 1500 RPM at idle or while driving. This may be due to the transmission park manual release cable vibrating against the transmission. This can be resolved by isolating the transmission park manual release cable with Rotunda PVC foam tape (164-R4901) or equivalent, where it is contacting the transmission. Replacement of the transmission park manual release cable is not necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2018-2021 EcoSport/Expedition/Navigator, 2019-2021 Ranger/Transit Connect, 2020-2021 Escape/Explorer/SuperDuty/Transit/Aviator/Corsair, 2021 Bronco Sport/F-150/Mustang/Mach-E the Workshop Manual (WSM) diagnostics may direct to replace a module on vehicles that use Ford Diagnosis and Repair System (FDRS). First, an FDRS session must be created on the vehicle prior to removing the faulted module. Once the session is started, run the Programmable Module Installation and replace the module only when instructed by FDRS. Installing a new module prior to starting a scan tool session may result in incomplete module configuration with DTCs U2100, U2101 and/or U2200. Once a session has been started, continue to follow normal WSM procedures to repair the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Aviator and Explorer vehicles built on and before 24-Feb-2021 may experience an intermittent no crank, inoperative remote start, and/or an illuminated wrench light with diagnostic trouble codes (DTCs) P07E4, B135C and/or U0103. This may be due to a loose ground G210 and/or G214. Check grounds G210 and G214, refer to the Wiring Diagram for location information. If the concern persists, or the grounds are found to be secure, refer to the Workshop Manual and applicable sections of the Powertrain Controls/Emissions Diagnosis (PC/ED) Manual for normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2021 Explorer/Aviator vehicles equipped with all-wheel drive (AWD) may exhibit an illuminated AWD indicator with diagnostic trouble code (DTC) C00A6:07, C00A6:18, C00A6:19, C00A6:4B, C00A6:66, C00A6:71, C00A6:74, and/or C00A6:99. It may not be necessary to replace the transfer case clutch actuator. Follow the updated transfer case clutch actuator Pinpoint Tests in the Workshop Manual (WSM), Section 308-07A for 2020 vehicles and Section 307-07A for 2021 vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator vehicles equipped with an 10R60 automatic transmission may exhibit diagnostic trouble code (DTC) P27B2 stored in the powertrain control module (PCM) memory. This DTC may be present due to activation of the transmission park by wire manual release during vehicle assembly and has not yet achieved the 40 warm up cycles needed to be cleared from memory. Before attempting a repair for this DTC, clear the DTC and if it returns, refer to the WSM, Section 307-01 for normal diagnostics. For claiming, use causal part 12A650 and applicable labor times in section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with DTC P025A And/Or DTC U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs or loose/corroded grounds. Inspect FPCM connector, applicable grounds(F-150- G401, Expedition/Navigator- G403, Transit- G401, 2018-2019 Explorer G302, 2020-2021 Explorer/Aviator- G407) and confirm FPCM connector (F-150- C4336, Expedition/Navigator- C433, Transit- C433, 2018-2019 Explorer C3239, 2020-2021 Explorer/Aviator- C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit various electrical concerns due to an open 3 or 4 post fuse array on the high current battery junction box (BJB). Service part LU5Z-14526-ALD has been released for the 3 post fuse array and LU5Z-14526-ANC has been released for the 4 post fuse array. It is no longer necessary to order the complete wiring harness to obtain these parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In some of the affected vehicles, the Electric Brake Booster (EBB) may contain a cracked solenoid valve plunger that may break and move out of position. A dislocated valve plunger may lead to the driver experiencing any of the following symptoms: Hard brake pedal, over-braking condition, and if certain other conditions are present, longer brake pedal travel with an incremental increase in stopping distance that would be accompanied by a red brake warning indicator lamp on the instrument panel cluster
Source components: ELECTRICAL SYSTEM · EQUIPMENT · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code on the PTS website (Detailed Vehicle Specifications). If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early March. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early March. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator/Police Interceptor Utility vehicles built on or before 24-Dec-2020 may exhibit an illuminated anti-lock brake system (ABS) warning indicator lamp with diagnostic trouble code (DTC) C0020 stored in the ABS module. It may not be necessary to replace the ABS module/hydraulic control unit (HCU) to resolve DTC C0020. This may be due to a poor ground connection and/or improper plating on the attachment bolts at G108. To correct the condition, follow the Service Procedure to replace and properly tighten the ground cable fasteners.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer vehicles equipped with a 10R60/10R80-MHT automatic transmission and built on or before 29-Oct-2020 may exhibit an illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTCs) U0100, U0155, P166B, P0929, and/or P0919. The vehicle may also exhibit an illuminated powertrain malfunction (wrench) indicator lamp. This may be due to the software in the gear shift module (GSM). To correct the condition, reprogram the GSM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 20-2364 to update the production fix date. Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles built on or before 24-Dec-2020 may exhibit an illuminated anti-lock brake system (ABS) warning indicator lamp with diagnostic trouble code (DTC) C0020 stored in the ABS module. It may not be necessary to replace the ABS module/hydraulic control unit (HCU) to resolve DTC C0020. This may be due to a poor ground connection and/or improper plating on the attachment bolts at G108. To correct the condition, follow the Service Procedure to replace and properly tighten the ground cable fasteners.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In some of the affected vehicles, a leak in the transmission oil cooler may occur due to a crack developing near the oil cooler line fittings. Loss of transmission fluid could lead to transmission noise, harsh shifts or the inability to shift out of park.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine may appear to have low engine oil level if the proper procedures are not followed. Refer to the Owners Guide, Maintenance, Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator vehicles equipped with 3rd row power seats may exhibit inoperative 3rd row power seat folding with diagnostic trouble codes (DTCs) B1231:54 and/or B1232:54 stored in the power fold seat module (SCMJ). This may be due to the software in the SCMJ. To correct the condition, connect a battery charger and reprogram the SCMJ using the latest software level of the appropriate Ford diagnostic scan tool. Then open the liftgate, and perform the SCMJ - Power Fold Seat Module (SCMJ) Learn Seat Procedure. For claiming, use causal part 14F042 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator vehicles built on or before 07-Dec-2020 may falsely store diagnostic trouble codes (DTCs) U0415 and/or U3000:42 in the image processing module B (IPMB). These DTCs may be associated with camera display issues or a Reverse Brake Assist Unavailable fault message. To correct the condition, reprogram the IPMB using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 19H405 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles built on or before 29-Feb-2020 may exhibit an illuminated anti-lock brake system (ABS) warning indicator lamp with diagnostic trouble code (DTC) C0020 stored in the ABS module. It may not be necessary to replace the ABS module/hydraulic control unit (HCU) to resolve DTC C0020. This may be due to a poor ground connection and/or improper plating on the attachment bolts at G108. To correct the condition, follow the Service Procedure to replace and properly tighten the ground cable fasteners.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit an illuminated anti-lock brake system (ABS) warning lamp with diagnostic trouble codes (DTCs) C0031, C0034, C0037, and/or C003A. This may be due to metal contamination on the wheel speed sensors or wheel speed sensor rings. Verify that all wheel speed sensors and wheel speed sensor rings are free of metal contamination before replacing them. Refer to Workshop Manual (WSM), Section 206-09 for diagnostics.
Source components: EQUIPMENT · SERVICE BRAKES · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles built on or before 19-May-2020 and equipped with a 10R60 automatic transmission may exhibit a harsh 7-6 gear downshift. This may be caused by the A clutch piston return spring snap ring becoming dislodged. To correct the condition, follow the Service Procedure steps to replace the front support and A clutch assemblies.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/Nautilus/Ranger, 2020 Escape and 2020-2021 Corsair/Explorer vehicles equipped with a 2.0L/2.3L EcoBoost may exhibit a lack of power with an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P02AB, P0243, P0299, P1464, P25B3, P25B4, P2AB7, P2AB8 and/or P2AB9. This may be due to a missing wastegate actuator e-clip. A lower level service component has been released, K2GZ-9G488-B for Edge/Nautilus/Escape/Corsair vehicles and LB5Z-9G488-B for Explorer/Ranger vehicles, for service to replace the actuator, actuator rod and both e-clips. Turbocharger replacement is not necessary for missing wastegate actuator e-clips.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Ford and Lincoln vehicles may exhibit the vehicle locator feature display the vehicle location incorrectly when using the Ford Pass/Lincoln Way mobile app. Customers may report that the vehicle location that is displayed is the Ford manufacturing facility were the vehicle was assembled, yet all other features work as intended. This may be due to the vehicle location not updating since assembly. If all other Ford Pass/Lincoln Way features work correctly except for the vehicle location, open the customer connectivity settings on the SYNC display and verify that the location setting is enabled. If the setting is currently enabled, disable and then re-enable the feature. If the vehicle location is still displayed incorrectly in the app, follow Workshop Manual section 415-00 for further diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Police Interceptor Utility vehicles equipped with a 3.3L hybrid engine and built on or before 21-Oct-2020 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) U0100 stored in the battery energy control module (BECM). This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles equipped with a 2.3L/3.0L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) and/or Engine Coolant Over Temperature warning with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0128, P0217, P0330, P1026, P1299, and/or P130D. This may be due to the engine coolant temperature (ECT) sensor or ECT sensor wiring harness. For 2.3L vehicles, replace the ECT sensor and pigtail wiring connector (GU2Z-14S411-KA). For 3.0L vehicles, replace the ECT and knock sensor. To aid with the engineering investigation, do not disconnect the wiring connector from the ECT sensor during disassembly. Leave the connector on the sensor in case parts are called back for analysis.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator vehicle may exhibit a water leak in the rear liftgate area and/or exhibit water in the spare tire area. To correct the condition, follow the Service Procedure steps to identify the leak path.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer Base vehicles equipped with blind spot information system (BLIS) and class III trailer tow package 52T may exhibit an illuminated BLIS indicator and/or inability to turn the BLIS system off. This may be due to the software in the instrument panel cluster (IPC). To correct the condition, perform a programmable module installation (PMI) on the IPC using the appropriate Ford diagnostic scan tool. For claiming, use causal part 10849 and applicable labor times from Section 10 in the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine and built on or before 01-Dec-2020 may exhibit inoperative air conditioning, an illuminated malfunction indicator lamp, and/or an illuminated powertrain malfunction (wrench) indicator with various diagnostic trouble codes present and a blown fuse F14. This may be due to wiring harness 14290 chaffing on the A/C compressor pulley. If chaffing is present, repair as necessary. Refer to Wiring Diagram, Cell 005 for repair procedures. Make sure that the wiring harness retainer is fully seated in the back side of the bracket on the A/C compressor to keep the harness away from the compressor pulley.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a 3.0L EcoBoost engine may exhibit a rough idle with the air conditioning (A/C) on. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a 10R60/10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift with or without an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTCs) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6, P07F7, P0751, P0756, P0761, P0766, P0771, P2707, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM). This may be due to sticking valves in the main control valve body. Most vehicles will improve and no longer exhibit the condition after the first 8,000 km (5,000 mi) of driving. To correct the condition, follow the Service Procedure steps to perform the PCM - Transmission Accelerated Main Control Break In routine for the appropriate clutch(s) and/or replace the main control valve body.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 MKC, 2019-2020 Edge/Nautilus/Escape/Ranger, 2020 Corsair, 2019-2021 Explorer vehicles equipped with 2.0L and 2.3L EcoBoost engines may exhibit a light to moderate ticking type noise at idle (600-700 RPM). The noise is usually more prominent in the area of the high-pressure fuel pump, located on the top of the engine just behind the number 4 ignition coil. This noise is not detrimental to engine function and has no short or long-term effects on engine durability. This an operating characteristic of these engines and no repairs should be attempted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Aviator and Explorer vehicles may experience an intermittent no crank, inoperative remote start, and/or an illuminated wrench light with diagnostic trouble codes (DTCs) P07E4, B135C and/or U0103. This may be due to a loose ground G210 and/or G214. Check grounds G210 and G214, refer to the Wiring Diagram for location information. If the concern persists, or the grounds are found to be secure, refer to the Workshop Manual and applicable sections of the Powertrain Controls/Emissions Diagnosis (PC/ED) Manual for normal diagnostics.
Source components: ELECTRICAL SYSTEM · ENGINE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code. If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 Ford and Lincoln vehicles equipped with a telematics control unit (TCU) may exhibit incomplete user authorization, inoperative remote features and/or a message stating the system cannot access the Lincoln/FordPass Connect feature in the application due to being a fleet vehicle. Replacing the TCU will not resolve this condition. Engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 MKZ, 2019-2020 EcoSport/Mustang/Continental/Fusion/F-150/Transit Connect/Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer vehicles may exhibit an illuminated malfunction indicator lamp (MIL) and diagnostic trouble codes (DTCs) U0100, U0155, P166B, P0929, and/or P0919. The vehicle may also exhibit an illuminated powertrain malfunction (wrench) indicator lamp. This may be due to the software in the gear shift module (GSM). To correct the condition, reprogram the GSM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:GEARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Aviator/Police Interceptor Utility vehicles built on 26-May-2020 and through 28-May-2020 may have been built with windshield washer fluid contaminated with brake fluid. If a vehicle exhibits a-pillar and/or rear liftgate trim or tail lamp appearance concerns, collect a sample of the washer fluid using a suction device and place in a white paper or Styrofoam cup. Washer fluid that appears green in color would indicate the washer fluid has been contaminated. Flush the washer fluid system and repair the affected windshield a-pillar area and liftgate area as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles built on or before 30-Sep-2020 may experience an intermittent or constant blank/black screen on the center infotainment display due the low voltage differential signaling (LVDS) cable at the SYNC accessory protocol interface module (APIM) not being fully seated. Verify that the connector is fully seated into the APIM prior to performing any other diagnostics or repairs on the vehicle for this concern. If the connection is found loose, re-seat the connection and retest.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a hybrid powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0C48, P0C49, P2B29, P0CFF, P0E1F, P0C4B, P0C4A, P2CF3, P0A06, P0A07, P2D01, P2D00, P2D03, P2D04, P0C73, and/or P2D02 stored in the powertrain control module (PCM). This may be due to the software in the battery energy control module (BECM). To correct the condition, follow the Service Procedure to reprogram the BECM.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit various electrical concerns due to an open 3 or 4 post fuse array on the high current battery junction box (BJB). Service part LU5Z-14526-ALD has been released for the 3 post fuse array and LU5Z-14526-ANC has been released for the 4 post fuse array. It is no longer necessary to order the complete wiring harness to obtain these parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor vehicles built on or before 19-Aug-2019 may exhibit an A/C system that is inoperative or does not cool properly. This may be due to a low refrigerant charge and/or system leak. Normal Workshop Manual (WSM) diagnosis and testing procedures may not verify any leaks. If this occurs, pressurize the system and spray the brazed joint of the thermostatic expansion valve manifold and tube assembly with soapy water just above where the retaining bracket/insulator bolts to the right side frame rail and check for leaks.