2016 Ford EXPLORER Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–198 of 198, ordered newest first. Dated records on this page: Jun 1, 2015–Dec 14, 2018.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Dec 14, 2018Service Bulletin/Repair Instructions
SSM 47711
NHTSA communication ID: 10153948
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Explorer/Police Interceptor Utility vehicles equipped with a 3.5L EcoBoost engine built on or before 30-Sep-2016 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0325, P0327, P0330 and/or P0332. This may be caused by a wire chafe condition near the knock sensor connector C109. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.
Source components: STEERING · STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Explorers equipped with the power folding 3rd row seat may experience a seat that will not latch/unlatch from folded or normal positions. This may be due to misalignment between the seat latch and the anchor bracket or misalignment between the load floor support and the load floor panel. If the seats attempt to move and stop, attempt to neutralize the anchor brackets and load floor support brackets to improve latch alignment before replacing any parts. Refer to Workshop Manual (WSM) Section 501-10C for torque specifications.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Explorer vehicles built on or before 07-Aug-2018 may automatically switch from A/C to heat and defrost after 1 minute during a remote start event when the customer expects the A/C to remain on. To resolve the concern, reprogram the heating, ventilation and air conditioning (HVAC) control module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 19980 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 Police Interceptor Sedan and Utility vehicles may exhibit a reduced top speed after a transmission fluid service with unapproved fluid. The use of unapproved fluid or improper transmission fluid level can lead to reduced vehicle performance and transmission damage that is not covered under warranty. Use only Mercon LV Automatic Transmission Fluid, XT-10-QLVC (US), CXT-10-LV12 (Canada). Use only the Transmission Fluid Exchanger process when performing service intervals. Check and adjust transmission fluid level only at normal operating temperatures of 82?C-93?C (180?F-200?F). The fluid adjustment procedure requires using the appropriate Ford scan tool or equivalent to verify fluid temperature. For optimum performance at high speeds, adjust fluid level to the top of the "MIN" mark on the dipstick.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Police Interceptor Utility vehicles may have an illuminated MIL with ambient air temperature (AAT) sensor DTC P0073. During the installation of certain police accessories by non-Ford vehicle upfitters, wiring connector C134 may have been left disconnected following the removal and installation of the front bumper cover. If this issue is noted, first check C134 before beginning other diagnostic steps. Reconnecting C134 due to improper reassembly by an outside supplier is not a warrantable repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Explorer and Police Interceptor Utility vehicles equipped with 3.5L Ecoboost engines may exhibit a surge or hesitation condition at approximately 50-60 MPH in 6th gear under light to moderate loads. If there are no DTCs stored in the powertrain control module (PCM), do not attempt further repairs. Advise customers this is a normal characteristic of the vehicle and will not affect durability of the engine or transmission.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost, 2013-2018 Fusion vehicles equipped with 2.0L/2.7L EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016 Explorer vehicles built on or before 31-Jan-2016 may exhibit a pop or creak noise from the right front mounting bolt of the front subframe. This condition may be due to a mispositioned weld between the barrel nut and the subframe mounting bracket. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Explorers equipped with the power folding 3rd row seat may experience a seat that will not latch/unlatch from folded or normal positions. This may be due to misalignment between the seat latch and the anchor bracket or misalignment between the load floor support and the load floor panel. If the seats attempt to move and stop, attempt to neutralize the anchor brackets and load floor support brackets to improve latch alignment before replacing any parts. Refer to Workshop Manual (WSM) Section 501-10C for torque specifications.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Explorer vehicles may automatically switch from A/C to heat and defrost after 1 minute during a remote start idle when the customer expects the A/C remain on. The system will return to normal operation after the ignition is turned to the run position. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. To assist with the investigation, use the Report A Vehicle Concern link at the bottom of the OASIS report to complete the form.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RKE stand alone key fobs can be added to 2016 and newer Police Utility vehicles not previously equipped with them. To program the fobs, start an IDS session and enter the Red Toolbox > Module Programming > Programmable Parameters > Police Mode > Remote Keyfob Learn > Enable. Next, refer to the RKE Transmitter Programming procedure listed in Workshop Manual (WSM), Section 501-14 > General Procedures to program the fobs. If the RKE fobs fail to program, verify that the fobs are the correct part number. If the fobs are correct for the vehicle, then refer to the inoperative key fob diagnostics outlined in WSM, Section 501-14. This procedure and part numbers do not apply to 2015 and previous model year Police Utility vehicles. Blue lift gate button fobs are part No. GB5Z-15K601-C and red panic button fobs are part No. GB5Z-15K601-A.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Police Interceptor Utility vehicles equipped with a 3.7L twin independent variable camshaft timing (TiVCT) engine may exhibit an engine vibration and/or the engine mount leaking fluid. A revised engine mount (GB5Z-6038-A) has been released to address this condition. For claiming, use causal part 6038 and applicable labor operations in Section 06 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2007-2016 Edge/MKX/Flex/MKT/MKZ/MKS/Taurus/Police Interceptor Sedan/Explorer/Police Interceptor Utility vehicles equipped with AWD and built on or before 30-Jun-2016 may exhibit a propane or natural gas odor during idle or low speed driving. This may be due to break down of the power transfer unit (PTU) fluid caused by excessive heat. If the source of the odor is identified as originating from the PTU, an idler bearing repair kit is available to repair the PTU. Refer to the Workshop Manual (WSM), Section 308-07. If the PTU is determined to be repairable, utilize kit GB5Z-7P258-A and the included instruction sheet. For claiming use causal part 7P258 and applicable labor operations in section 07 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Explorer vehicles equipped with Hankook brand tires may exhibit tread wear that is not the result of vehicle alignment concerns. For customer satisfaction, Hankook is offering pro-rated tire replacement for vehicles with less than 36,000 Miles. This program is managed by Hankook Tire America Corp. and not claimed under Ford new vehicle limited warranty. If the tire side wall is marked as: 255/50R20 105H Ventus S1 Noble 2, contact Hankook Technical Service for possible pro-rated tire replacement. Refer to FMCDealer.com Tire Page for details and Hankook contact information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Explorer vehicles may exhibit front window glass that jumps/chatters during up/down movement. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Explorer vehicles equipped with automatic temperature control and premium AM/FM/CD may exhibit a broken or missing temperature control switch. The driver and passenger switches are now available separately from the control head. Replacement of the control head assembly is not necessary. The switches are driver and passenger specific and must be installed in the correct location with the red heat indicator facing up. HB5Z-19986-AA - Drivers Side Switch, HB5Z-19986-BA - Passengers Side Switch
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 Explorer signature lighting is standard equipment on XLT and higher level vehicles. Base model vehicles are not equipped with signature lighting and it is not an option. Base level vehicles without the LED lighting surrounding the headlamps are built correctly and should not be modified by installing the signature lamps. Prior to beginning any diagnostics, verify the proper vehicle model/series utilizing OASIS or referring to Workshop Manual Section 100-01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Police Interceptor Utility vehicles may exhibit flickering front amber marker lamps (inboard amber lights under the headlamps) when the engine is running. Before attempting repairs, verify the frequency type using the Integrated Diagnostic System (IDS) or equivalent. The frequency type in police mode programmable parameters must be set to type 2. The engine must be running for the configuration to complete if this parameter is changed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
Source components: ENGINE · POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Explorer vehicles equipped with a manual front passenger seat may exhibit a stuck condition in the full forward position. This may be caused by the seat being moved firmly from the rearward position to the forward position causing the seat track travel restrictor to bend allowing the adjuster bar to become trapped under the travel restrictor. Follow the Service Procedure to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2016 Explorer/Police Interceptor Utility vehicles may exhibit delamination of the top edge of the front door trim panels. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Explorer vehicles equipped with Hankook brand tires may exhibit chipping, cutting and/or unusual or even accelerated tread wear. If the tire side wall is marked as: 255/50R20 105H Ventus S1 Noble 2 contact Hankook Technical Service for possible pro-rated tire replacement. This may not be the result of improper alignment. For Hankook contact information refer to the Tire Warranty information located on FMCDealer.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Police Interceptor Utility vehicles may exhibit flickering front amber marker lamps (inboard amber lights under the headlamps) when the engine is running. Before attempting repairs, verify the frequency type using the Integrated Diagnostic System (IDS) or equivalent. The frequency type in police mode programmable parameters must be set to type 2. The engine must be running for the configuration to complete if this parameter is changed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2017 Explorer roof rack cap clips are now available as a separate part. It is no longer necessary to order a complete roof rack rail to obtain the cap retainer clips. To correct loose roof rack caps or broken or missing clips, order part # FB5Z-7851050-A. The package contains 7 clips.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Explorer and 2015-2016 F-150 vehicles, equipped with 3.5L Gasoline Turbocharged Direct Injection (GTDI) engines may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P2195, P2197, P2626, and/or P2629 stored in powertrain control module (PCM) memory. Follow the Service Procedure Steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016 Edge/Explorer/F-150/Mustang built on or before 01-Nov-2016 and equipped with a 4.2-inch FCDIM may exhibit a blank screen. To correct the concern, Reprogram the FCDIM to the latest level using IDS release 104.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 10D885 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2017 Edge/MKX/Flex/MKT/MKZ/MKS/Taurus/Taurus Police/Explorer/Explorer Police/Continental vehicles equipped with a 3.5L or 3.7L engine, all wheel drive (AWD) and a power transfer unit (PTU) that is being repaired or replaced for an internal failure must also have the vent hose replaced due to contamination in the hose.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2016-2017 EXPLORER VEHICLES EQUIPPED WITH A 2.3L ENGINE AND BUILT ON OR BEFORE 28-FEB-2017 MAY EXHIBIT THE IDLE SPEED DROPPING BELOW SPECIFICATION AFTER REPEATED LIGHT PEDAL TIP-IN/TIP-OUT EVENTS AT LOW VEHICLE SPEEDS, SUCH AS IN HEAVY TRAFFIC JAMS OR A PARKING LOT MANEUVERS. REPROGRAM THE POWERTRAIN CONTROL MODULE (PCM) TO THE LATEST CALIBRATION USING IDS RELEASE 104.04 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2016 EDGE/EXPLORER/F-150/MUSTANG BUILT ON OR BEFORE 01-NOV-2016 AND EQUIPPED WITH A 4.2-INCH FCDIM MAY EXHIBIT A BLANK SCREEN. TO CORRECT THE CONCERN, REPROGRAM THE FCDIM TO THE LATEST LEVEL USING IDS RELEASE 104.02 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. FOR CLAIMING, USE CAUSAL PART 10D885 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2007-2016 EDGE/MKX/FLEX/MKT/MKZ/MKS/TAURUS/TAURUS POLICE/EXPLORER/EXPLORER POLICE EQUIPPED WITH ALL WHEEL DRIVE (AWD) AND BUILT ON OR BEFORE 30-JUN-2016 MAY EXHIBIT A TICKING AND/OR KNOCKING NOISE COMING FROM THE DRIVELINE AREA. TO IDENTIFY THIS NOISE, REFER TO WORKSHOP MANUAL (WSM), SECTION 100-04, AND FOLLOW THE SYMPTOM CHART. IF THE SOURCE OF THE NOISE IS IDENTIFIED AS THE PTU AND/OR INTERNAL TO THE PTU, DISASSEMBLE PTU ASSEMBLY. REFER TO UPDATED WSM, SECTION 308-07. IF THE PTU IS DETERMINED TO BE REPAIRABLE, UTILIZE KIT GB5Z-7P258-A AND THE INCLUDED INSTRUCTION SHEET. FOR CLAIMING, USE CAUSAL PART 7P258 AND APPLICABLE LABOR OPERATIONS IN SECTION 07 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN:DRIVELINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2016 EDGE, F150, EXPLORER, AND MUSTANG VEHICLES EQUIPPED WITH A MYFORD DISPLAY 4 INCH SCREEN MAY EXHIBIT A BLANK SCREEN AND NO AUDIO. REPROGRAM THE FRONT CONTROL DISPLAY INTERFACE MODULE (FCDIM) TO THE LATEST CALIBRATION USING INTEGRATED DIAGNOSTIC SYSTEM (IDS) RELEASE 104.01 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE CAUSAL PART NUMBER 10D885 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MULTIPLE 2014-2016 VEHICLES EQUIPPED WITH 6F35 TRANSMISSION AND BUILT ON 1-JAN-2014 AND THROUGH 31-DEC-2015 MAY EXHIBIT HARSH REVERSE ENGAGEMENT AND HARSH/DELAYED 3RD AND 5TH GEAR UP/DOWN SHIFTS WITH NO DTCS PRESENT. THIS MAY BE DUE TO A MECHANICALLY BINDING SHIFT SOLENOID B (SSB). VERIFY HARSH REVERSE AND 3RD AND 5TH GEAR SHIFT EVENTS ARE PRESENT. USING IDS, IDENTIFY THE BAND NUMBER OF SSB FOR USE WHEN ORDERING PARTS. REMOVE THE MAIN CONTROL. DISASSEMBLE AND THOROUGHLY CLEAN THE VALVE BODY AND SOLENOID BODY TO REMOVE ANY CONTAMINANTS. REPLACE SSB, REFER TO WORKSHOP MANUAL (WSM) SECTION 307-01. USING IDS, CLEAR TRANSMISSION ADAPTIVE TABLES. FOR CLAIMING, USE CAUSAL PART 7G383 AND APPLICABLE LABOR OPERATIONS IN SECTION 7 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
Source components: POWER TRAIN:MANUAL TRANSMISSION:SHIFT PATTERN INDICATOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2016-2017 EXPLORER POLICE UTILITY VEHICLES MAY HAVE AN ILLUMINATED MIL WITH AMBIENT AIR TEMPERATURE SENSOR DTC P0073. DURING THE INSTALLATION OF CERTAIN POLICE ACCESSORIES BY NON-FORD VEHICLE UPFITTERS, WIRING CONNECTOR C134 MAY HAVE BEEN LEFT DISCONNECTED FOLLOWING THE REMOVAL AND INSTALLATION OF THE FRONT BUMPER COVER. IF THIS ISSUE IS NOTED, FIRST CHECK C134 BEFORE BEGINNING OTHER DIAGNOSTIC STEPS. RECONNECTING C134 DUE TO IMPROPER REASSEMBLY BY AN OUTSIDE SUPPLIER IS NOT A WARRANTABLE REPAIR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2017 EDGE/MKX, ESCAPE/MKC, FUSION/MKZ AND EXPLORER VEHICLES EQUIPPED WITH A 2.0L OR 2.3L MAY EXHIBIT DAMAGE TO THE ENGINE APPEARANCE COVER, VALVE COVER AND/OR INTAKE MANIFOLD WHEN ATTEMPTING TO REMOVE THE APPEARANCE COVER. TO REDUCE THE POSSIBILITY OF DAMAGE, CAREFULLY PULL STRAIGHT UPWARD ON THE UNDERSIDE OF THE COVER AT EACH FASTENER LOCATION TO REMOVE. DO NOT PULL THE COVER FORWARD OR TO THE SIDE. BEFORE INSTALLING THE ENGINE APPEARANCE COVER, APPLY MOTORCRAFT SILICONE BRAKE CALIPER GREASE AND DIELECTRIC COMPOUND (XG-3-A) TO THE COVER FASTENER GROMMETS. WORKSHOP MANUAL (WSM) INFORMATION IS IN THE PROCESS OF BEING UPDATED
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2016 EDGE WITH 2.0L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI), 2015-2016 MUSTANG AND F-150 WITH 5.0L ENGINE AND 2016 EXPLORER EQUIPPED WITH 2.3L GTDI ENGINE MAY EXHIBIT OIL LEAK AT ENGINE OIL PRESSURE (EOP) SENSOR THREADS. IT IS NOT REQUIRED TO REPLACE THE SENSOR IF IT IS LEAKING FROM THE THREADS. REMOVE AND RESEAL THE EOP SENSOR, REFER TO WORKSHOP MANUAL (WSM), SECTIONS 303-14. CHECK THE OIL LEVEL AND TOP OFF AS NECESSARY. REFER TO WSM, SECTION 303-01. USE CAUSAL PART 9278 AND APPLICABLE LABOR OPERATIONS IN SECTION 09 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2010-2016 EPAS EQUIPPED VEHICLES MAY EXHIBIT STEERING RELATED NOISES. THE WORKSHOP MANUAL (WSM) DIAGNOSTIC PROCEDURES HAVE BEEN UPDATED IN SECTION 211-02. WHEN DIAGNOSING AND REPAIRING EPAS STEERING NOISES USE THE UPDATED PROCEDURES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2017 EXPLORER SIGNATURE LIGHTING IS STANDARD EQUIPMENT ON XLT AND HIGHER LEVEL VEHICLES. BASE MODEL VEHICLES ARE NOT EQUIPPED WITH SIGNATURE LIGHTING AND IT IS NOT AN OPTION. BASE LEVEL VEHICLES WITHOUT THE LED LIGHTING SURROUNDING THE HEADLAMPS ARE BUILT CORRECTLY AND SHOULD NOT BE MODIFIED BY INSTALLING THE SIGNATURE LAMPS. PRIOR TO BEGINNING ANY DIAGNOSTICS, VERIFY THE PROPER VEHICLE MODEL/SERIES UTILIZING OASIS OR REFERRING TO WORKSHOP MANUAL SECTION 100-01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CERTAIN 2015 MODEL YEAR EDGE, 2015-2016 MODEL YEAR F-150, MKT, AND POLICE INTERCEPTOR SEDAN, AND 2016 MODEL YEAR ESCAPE, EXPLORER, FLEX, FUSION, MKX, MUSTANG, POLICE INTERCEPTOR UTILITY, TAURUS, AND TRANSIT VEHICLES - ELECTRONIC THROTTLE BODY REPLACEMENT
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2016 EXPLORER, FLEX, MKT, TAURUS, MKS AND TRANSIT VEHICLES EQUIPPED WITH A 3.5L GTDI ENGINE MAY EXHIBIT AN ILLUMINATED MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODE (DTC) P2096, P2097, P2098 AND/OR P2099 IN THE POWERTRAIN CONTROL MODULE (PCM) MEMORY. THIS MAY BE DUE TO INCORRECT CALIBRATION VALUES SETTING A SYSTEM DTC INSTEAD OF A CIRCUIT FAULT DTC. IF THE VEHICLE EXHIBITS DTC P2096, P0297, P0298 AND/OR P2099, PERFORM POWERTRAIN CONTROL/EMISSIONS DIAGNOSIS (PC/ED) PINPOINT TEST DW STEPS 9-12 FIRST TO VALIDATE THE HEATED OXYGEN SENSOR WIRING. IF NO CONCERNS ARE FOUND, CONTINUE WITH PC/ED PINPOINT TEST DZ.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SETTING THE CORRECT TIRE INFLATION PRESSURE IS AN IMPORTANT STEP IN THE PRE-DELIVERY PROCESS AND DURING ROUTINE MAINTENANCE INTERVALS. RECENT CUSTOMER CLINICS REVEALED THAT MOST EVERY VEHICLE IN THE CLINICS HAD THE TIRE PRESSURES SET INCORRECTLY. TIRE PRESSURES FROM THE FACTORY ARE NOT SET TO THE CORRECT SPECIFICATION. MAINTAINING THE CORRECT TIRE PRESSURE IS KEY TO THE RIDE CHARACTERISTICS OF THE VEHICLE AND AFFECTS RIDE QUALITY, HANDLING, LOAD CAPACITY AND TIRE WEAR. THE RECOMMENDED PRESSURE SETTINGS CAN BE FOUND ON THE TIRE INFORMATION LABEL IN THE DRIVER'S SIDE FRONT DOOR JAM. DO NOT USE THE TIRE PRESSURES LISTED ON THE SIDEWALL OF THE TIRES. MAINTAINING THE TIRE PRESSURE IS PART OF NORMAL MAINTENANCE. IT SHOULD BE RECHECKED MONTHLY, PER THE OWNER GUIDE AND DURING THE RECOMMENDED TIRE ROTATION INTERVALS.
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2008-2017 FORD/MERCURY/LINCOLN VEHICLES EQUIPPED WITH SYNC MAY GENERATE A VHR THAT IDENTIFIES A CONCERN WITH THE BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2008-2017 FORD/MERCURY/LINCOLN VEHICLES EQUIPPED WITH SYNC MAY GENERATE A VHR THAT IDENTIFIES A CONCERN WITH THE BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2016 EXPLORER VEHICLES EQUIPPED WITH FRONT PARKING AID AND BUILT ON OR BEFORE 10-MAY-2016 MAY EXHIBIT AN INTERMITTENT FRONT PARKING AID FAULT IN THE MESSAGE CENTER THAT MAY OR MAY NOT INCLUDE DTCS IN THE PARKING AID MODULE (PAM). THIS MAY BE DUE TO WATER INTRUSION INTO THE FRONT BUMPER WIRE HARNESS. FOLLOW THE TSB SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN HOOKING UP THE VEHICLE COMMUNICATION MODULE (VCM) AND INTEGRATED DIAGNOSTIC SYSTEM (IDS) TO THE DLC LOCATED ON THE DRIVER SIDE UNDER THE STEERING COLUMN AT THE GWM, MAKE SURE THAT THE IGNITION IS OFF BEFORE CONNECTING TO IDS. IF THE IGNITION IS ON OR THE ENGINE IS RUNNING DURING THE HOOK UP, IT CAN RESULT IN VARIOUS WARNING LIGHTS BEING ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTCS), NO START OR NO CRANK CONDITIONS OR THE CLUSTER INOPERATIVE. FOR LINCOLN VEHICLES, THIS INFORMATION IS NOW LISTED IN THE TECHNICAL INSPECTION AND POST ROAD TEST SECTIONS OF EPDI ON THE PTS WEBSITE. IF A VEHICLE DISPLAYS THESE ISSUES, DISCONNECT THE EQUIPMENT FROM THE DLC AND REINSTALL WITH THE IGNITION OFF. CLEAR ANY DTCS PRESENT AND RETEST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2016 F-150, C-MAX, EDGE, MKS, TAURUS, AND FLEX AND 2016 EXPEDITION, EXPLORER, ESCAPE, FUSION, MUSTANG, MKZ, MKX, NAVIGATOR, TRANSIT AND TRANSIT CONNECT VEHICLES EQUIPPED WITH A 2.0L, 2.5L, 3.5L OR 3.7L GASOLINE ENGINE AND BUILT ON OR BEFORE 31-MAY-2016 MAY EXHIBIT AN INTERMITTENT LOSS OF POWER AND/OR AN ILLUMINATED POWERTRAIN MALFUNCTION (WRENCH) LAMP WITH DIAGNOSTIC TROUBLE CODES (DTCS) P2111, P2112 AND/OR P2119 STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may have a concern where the safety belt retractor webbing does not extract from the stowed position or exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
Source components: ENGINE · ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:COOLING SYSTEM · ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN · ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS · ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY · ENGINE AND ENGINE COOLING:ENGINE · ENGINE AND ENGINE COOLING:ENGINE:DIESEL · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER · ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV) · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE) · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2016 vehicles equipped with 6F50/6F55 transmission Built On 11/2/2015 And Through 2/1/2016 may exhibit no reverse, 3rd and 5th gear and/or DTCs P0715, P0717, P0756 and/or P2701. This may be caused by the direct clutch snap ring out of position and/or damage to the direct clutch hub. The cause of the failure is the Tone Wheel surface putting uneven load on the snap ring. To repair this condition the Tone Wheel (7F283) must be replaced,(also referred to as Direct Clutch Cylinder/Tone wheel) in addition to the Tone Wheel, replace Direct Clutch Hub (7G384), Direct Clutch Return Spring (7F235), Direct Clutch Snap Ring (7C122), TSS Sensor (7M101), Seal Kit (7153) and filter in the kit. Disassemble, clean the transmission and main control to remove metal particles. Refer to WSM, Section 307-01. Use causal part 7F283 and applicable Labor ops from SLTS section 7.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015 Model Year Edge, 2015-2016 Model Year F-150, MKT, and Police Interceptor Sedan, and 2016 Model Year Escape, Explorer, Flex, Fusion, MKX, Mustang, Police Interceptor Utility, Taurus, and Transit Vehicles - Electronic Throttle Body Repair
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016 Explorer vehicles equipped with a 2.3L GTDI engine may exhibit an illuminated MIL with a lack of power and diagnostic trouble code (DTC) P0299. This may be due to the turbocharger wastegate actuator rod coming disconnected from the wastegate. Follow the Service Procedure steps to correct the condition.
Source components: ENGINE · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN HOOKING UP THE VEHICLE COMMUNICATION MODULE (VCM) AND INTEGRATED DIAGNOSTIC SYSTEM (IDS) TO THE DLC LOCATED ON THE DRIVER SIDE UNDER THE STEERING COLUMN AT THE GWM, MAKE SURE THAT THE IGNITION IS OFF BEFORE CONNECTING TO IDS. IF THE IGNITION IS ON OR THE ENGINE IS RUNNING DURING THE HOOK UP, IT CAN RESULT IN VARIOUS WARNING LIGHTS BEING ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTCS), NO START OR NO CRANK CONDITIONS OR THE CLUSTER INOPERATIVE. FOR LINCOLN VEHICLES, THIS INFORMATION IS NOW LISTED IN THE TECHNICAL INSPECTION AND POST ROAD TEST SECTIONS OF EPDI ON THE PTS WEBSITE. IF A VEHICLE DISPLAYS THESE ISSUES, DISCONNECT THE EQUIPMENT FROM THE DLC AND REINSTALL WITH THE IGNITION OFF. CLEAR ANY DTCS PRESENT AND RETEST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2016 EXPLORER VEHICLES EQUIPPED WITH THE HANDS-FREE POWER LIFTGATE AND WITHOUT TRAILER TOW PACKAGE MAY EXHIBIT A LIFTGATE THAT OPENS WHILE WALKING NEXT TO THE REAR BUMPER. THIS MAY BE DUE TO THE SOFTWARE SENSITIVITY IN THE HANDS-FREE LIFTGATE ACTUATION MODULE. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2016 F150, MUSTANG AND EXPLORER VEHICLES EQUIPPED WITH A 3.5L GTDI, 2.3L GTDI OR 2.7L GTDI ENGINE BUILT ON OR BEFORE 4/15/2016, AND EQUIPPED WITH ACTIVE NOISE CANCELLATION (ANC) OR ENGINE SOUND ENHANCEMENT (ESE), MAY EXHIBIT NO AUDIO AND/OR DISPLAY AN AUDIO OFF OR LOADING MESSAGE AFTER STARTING THE ENGINE. REPROGRAM THE AUDIO CONTROL MODULE (ACM) TO THE LATEST CALIBRATION USING IDS RELEASE 101.03 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE CAUSAL PART NUMBER 18C869 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SLTS MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2016 EXPLORER VEHICLES BUILT ON OR BEFORE 5/8/2016 MAY EXHIBIT A NOISE FROM THE ELECTRIC COOLING FANS, MOST NOTICEABLE RIGHT AFTER THE ENGINE IS TURNED OFF AS THEY SPIN DOWN TO A STOP. IF THE NOISE CAN BE PINPOINTED TO THE COOLING FAN MOTOR, REPLACE THE COOLING FAN ASSEMBLY WITH APPLICABLE UPDATED SERVICE PARTS. DA8Z-8C607-B REPLACED DA8Z-8C607-A, DG1Z-8C607-E REPLACED DG1Z-8C607-D, DG1Z-8C607-F REPLACED DG1Z-8C607-A, DB5Z-8C607-D REPLACED DB5Z-8C607-C. REFER TO WORKSHOP MANUAL (WSM,) SECTION 303-03. USE AVAILABLE SERVICE LABOR TIMES IN SECTION 08.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2017 FUSION/ESCAPE/MKZ (EXCLUDING 3.7L), 2015-2016 EDGE/EXPLORER (EXCLUDING 3.5L/3.7L), 2015-2016 MKC, AND 2016 MKX VEHICLES (EXCLUDING 3.7L) EQUIPPED WITH ALL WHEEL DRIVE (AWD) MAY EXHIBIT A LEAKING PASSENGER SIDE POWER TRANSFER UNIT (PTU) HALFSHAFT/LINKSHAFT SEAL. THIS MAY BE DUE TO A WORN PTU BUSHING. THE PTU BUSHING CAN NOW BE REPAIRED WITHOUT PTU REPLACEMENT. THE ONLINE WSM IS BEING UPDATED FOR ALL LISTED VEHICLES.REFER TO THE INTERMEDIATE SHAFT BUSHING REMOVAL AND INSTALLATION IN WORKSHOP MANUAL (WSM), SECTION 308-07. THE PROCEDURE IS THE SAME FOR ALL VEHICLES. IF THE PROCEDURE IS NOT PUBLISHED FOR THE VEHICLE BEING SERVICED CHECK THE WSM OF ANOTHER LISTED VEHICLE. BUSHING PART NUMBER IS F2GZ-63600A58A. THE PARTS CATALOG IS BEING UPDATED TO INCLUDE THIS BUSHING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2009-2010 F-150 AND 2011-2016 EXPLORER VEHICLES MAY HAVE A SEAT CUSHION COVER THAT APPEARS LOOSE NEAR THE FRONT OF THE SEAT. THIS MAY BE CAUSED BY THE SEAT CUSHION COVER J-RETAINER BECOMING DISENGAGED FROM THE SEAT CUSHION PAN FLANGE. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2016 EXPLORER VEHICLES EQUIPPED WITH FRONT PARKING AID AND BUILT ON OR BEFORE 5/10/2016 MAY EXHIBIT AN INTERMITTENT FRONT PARKING AID FAULT IN THE MESSAGE CENTER THAT MAY OR MAY NOT INCLUDE DTCS IN THE PARKING AID MODULE (PAM). THIS MAY BE DUE TO WATER INTRUSION INTO THE FRONT BUMPER WIRE HARNESS. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2016 F-150, EXPEDITION, NAVIGATOR, TRANSIT, EDGE, FLEX AND EXPLORER VEHICLES EQUIPPED WITH A 3.5L TWIN INDEPENDENT VARIABLE CAM TIMING (TI-VCT) OR A 3.5L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI) ENGINE WITH LESS THAN 3200 KM (2000 MILES) MAY EXHIBIT AN ILLUMINATED MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODES (DTCS) P0011, P0015, P0016, P0017, P0018, P0019, P0021 AND/OR P0025 STORED IN THE POWERTRAIN CONTROL MODULE (PCM) MEMORY.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2016 EXPLORER AND MKX VEHICLES BUILT ON OR BEFORE 3/11/2016 MAY EXHIBIT A MEMORY SEAT THAT DOES NOT RETURN TO THE PROGRAMMED POSITION WHEN PRESSING THE MEMORY SEAT SWITCH OR PROGRAMMED INTELLIGENT ACCESS (IA) KEY; AND/OR EASY ENTRY/EXIT FUNCTION THAT DOES NOT RETURN TO THE PREVIOUS SEAT POSITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.5L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI) ENGINE MAY EXHIBIT A MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODES (DTC) P0327/P0332.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2016 EDGE AND 2016 EXPLORER VEHICLES BUILT ON OR BEFORE 2/12/2016 EQUIPPED WITH CLIMATE CONTROLLED SEATS MAY EXHIBIT A LACK OF COOLING PERFORMACE FROM THE FRONT SEAT BACKRESTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In some of the affected vehicles, the front control/display interface module (FCDIM) may have been unintentionally programmed for the European market instead of the North American market
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016 FORD EXPLORER: TSB CONTAINS AN OWNER'S NOTIFICATION LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. THE SYNC 911 ASSIST FEATURE CAN'T BE ACTIVATED USING THE PROCEDURE LISTED IN THE OWNER'S MANUAL DUE TO IMPROPER CONFIGURATION AT THE PLANT *CN
NHTSA source summary · Original PDF not reviewed by Recallfolio
FORD EXPLORER 2014-2016: BULLETIN INFORMATION INVOLVING VEHICLES EQUIPPED WITH SECOND ROW INFLATABLE SEAT BELTS MAY EXHIBIT AN AIRBAG WARNING LIGHT ILLUMINATED WITH DTC B141B AND B141C. *LJ
Source components: AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FORD: SOME VEHICLES TRANSMISSION WILL EXPERIENCE, AFTER A COLD SOAK OR AN EXTENDED PERIOD WITH ENGINE OFF, A 2-3 SHIFT HESITATION DUE TO POSSIBLE HYDRAULIC CIRCUIT DRAIN. MODEL 2013-16 VARIOUS VEHICLES. *PE
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:MANUAL TRANSMISSION.