2025 Ford BRONCO Manufacturer communications & TSBs.Page 1
Original record summaries, dates and identifiers for this model-year. Records 1–99 of 99, ordered newest first. Dated records on this page: Feb 26, 2025–Aug 25, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Aug 25, 2026Service Bulletin/Repair Instructions
SSM 55118
NHTSA communication ID: 11036529
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the following vehicles: * 2023-2025 F-Super Duty built on or before 02-Feb-2025 * 2024-2026 Ranger/Bronco/Mustang * 2024-2025 F-150 built on or before 15-Jul-2025 * 2024-2025 Nautilus built on or before 16-Feb-2025 * 2025 Explorer/Aviator built on or before 01-Feb-2025 may exhibit all of the following symptoms: - "No Key Detected" message displayed on the instrument panel cluster (IPC). - Key fob does not work in the backup slot. - Remote keyless entry (RKE) (lock and unlock from the key fob) functionality will work to lock/unlock the vehicle. If the vehicle exhibits these symptoms, start the vehicle using both key fobs. If the no crank/no start condition with "No Key Detected" concern is present, reprogram both key fobs and retest. If the no crank/no start condition with "No Key Detected" is still present, replace the body control module (BCM). Refer to Workshop Manual (WSM), Section 419-10. For claiming, use causal part 15604 and labor operation MT55118SSM up to 1.8 hours.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For Various Ford and Lincoln vehicles, if diagnostics lead to the replacement of the front seat cushion cover J-clips, lower-level service parts are now available. Use service part W709919-S901 if the J-clip is completely detached from the seat cover and W715386-S424 if the clip is still partially attached. It is not necessary to replace the seat cover if only the J-clip is separating from the cover. Refer to PTS Home > Technical Assistance > Technical Support Videos > Section 501- Body and Paint > Seat J-Clips. For claiming, use causal parts from list below and labor operations 63100A and 63100A5. Causal Parts for claiming: Bronco/Bronco Sport/Escape/Explorer/Expedition/Navigator: 7862900 or 7862901 F-150/F-Super Duty: 1562900 or 1562901 Ranger/Maverick: 6062900 or 6062901
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Bronco vehicles equipped with a 7 speaker audio system (minor feature code IDBAL) may exhibit diagnostic trouble codes (DTC) B128A:01, B128A:11, B128A:12, B128A:13, B1288:11, B1288:12 and/or B1238:17 stored in the audio front control module (ACM) with no customer facing symptoms related to those DTCs. Clear the DTCs and if the DTCs return with no customer facing symptoms, this condition may be due to the ACM software. Replacement of the ACM and/or speakers will not resolve this condition. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in Q4 2026. Continue to monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If a vehicle exhibits this condition, enter the vehicle identification number (VIN) and click the "Submit Global Concern Report (GCR)" link at the upper right of the PTS "Vehicle ID" screen. Fill out the GCR form, referencing this article number in the report.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 Bronco vehicles may require the removal and installation of the transfer case for various reasons. Installation requires Loctite® 243 adhesive applied to the mounting bolt threads in the transmission. Make sure that the mating faces are clean and dry. Tightening the mounting bolts also requires an updated two-stage tightening sequence. Workshop Manual (WSM), Sections 307-07C/D and 308-07C/D Installation > Transfer Case have been updated to reflect this change.
Source components: POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Bronco/Ranger vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P2122, P2123, P2127, P2128, and/or P2138 stored in the powertrain control module (PCM). The vehicle may or may not exhibit a perceived lack of power intermittently. This may be due to an issue with the following connectors associated with the accelerator pedal position (APP) sensor circuits: -C115B -C175B -C2040 Replacement of the accelerator pedal may not resolve this concern. Perform a wiggle test of the connectors while the engine is at normal operating temperature. Perform a visual inspection of the connectors as well as a terminal fit test using the appropriately sized flex probe. Repair as necessary. Refer to Wiring Diagram Cell 005. If no concerns are found, refer to Workshop Manual (WSM), Section 310-02 for normal diagnostics.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
Source components: ELECTRICAL SYSTEM · FUEL/PROPULSION SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Bronco/Bronco Sport/Corsair/F-150/F-Super Duty/Maverick/Mustang/Mustang Mach-E/Ranger vehicles may exhibit a no audio/sound condition. This may be due to the software in the audio control module (ACM). To determine if it is a software concern, disconnect the vehicle's 12-volt battery cables for 10 minutes and reconnect. If the concern is still present, continue with normal diagnostics in Workshop Manual (WSM), Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing and repair as necessary outside of this article. If the no audio/sound concern is resolved, reprogram the ACM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 18C869 and labor operations 10654C, 12651D and 12651D4.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 Bronco vehicles may exhibit a "Park Brake Limited Function Service Required" message in the instrument panel cluster (IPC). This may be due to an issue with the driver door harness connector after removing and installing the removeable doors. If diagnostic trouble code (DTC) B1625:29 is stored in the driver door module (DDM), inspect connector C322C between the upper and lower door hinges that attaches to the body for proper installation and/or pin fitment. Repair as necessary. If the condition was caused by improper door installation, do not submit a claim for this condition. If no concerns are found with the connector, refer to Workshop Manual (WSM), Section 501-11 > Diagnosis and Testing for normal diagnostics.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NEW VEHICLE DELIVERY HOLD - Emissions Recall 26E04 Certain 2021-2025 Model Year F-150, Maverick, Mustang, Ranger, Expedition, Bronco Sport, Explorer, Bronco, Navigator, and Aviator Vehicles Powertrain Control Module Software Update
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2026 Bronco vehicles may exhibit various TRM concerns when attempting first time installation of a dealer installed accessory TRM, including one or more of the following: TRM unable to be programmed -Trailer lights inoperative -DTC U2100 stored in the TRM. This may be due to any of the following conditions:-The incorrect trailer tow kit is being installed. The TRM is model year specific. Refer to the parts catalog using the VIN and base part number 15A416 for the vehicle specific trailer tow kit.-The "TRM - Trailer Module (TRM) Configuration" application being run instead of the "Towbar Configuration" application during first time TRM installation using the Ford Diagnosis and Repair System (FDRS). Dealer installed accessory TRMs are preprogrammed and only the "Towbar Configuration" application should be run during first time TRM installation to configure the TRM properly and support proper function of trailer tow capabilities. Any attempts to program the TRM using the "TRM - Trailer Module (TRM) Configuration" application a
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0300 and/or P0316 stored in the powertrain control module (PCM) (with no other relevant DTCs present) during a cold start after a 3 to 8 hours cold soak. This may be due to the machining surface of the intake ports in the cylinder head.
Source components: ELECTRICAL SYSTEM · ENGINE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes 25-2551. Reason for update: to correct the descriptions for the liftgate glass weather seals. Some of the vehicles listed in the model statement above may exhibit paint wearing along on the top inner edge of the tailgate where the rear window weather strip contacts the tailgate. This may be due to the accumulation of dirt between the rear window seal and tailgate.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2026 Bronco vehicles may exhibit a condition where short drop windows, window bounce-back, and/or one-touch open/close does not operate properly. This may be due to loss of window initialization. Replacement or reprogramming of the DDM, PDM, and/or any other components may not resolve these conditions. The short drop windows feature may be restored by performing a reset procedure as described in the Digital Owner's Manual > Windows > Using Short Drop Windows > Resetting Short Drop Windows. If the customer is experiencing an inability to fully close the window due to repeated bounce-back events, the window bounce-back feature may be overridden by performing an override procedure as described in the Digital Owner's Manual > Windows > Window Bounce-Back > Overriding Windows Bounce-Back. The one-touch open/close feature may be restored by performing a reset procedure as described in the Digital Owner's Manual > Windows > Opening and Closing the Windows > Resetting Window One-Touch. These symptoms may return after a successful reset/override
Source components: ELECTRICAL SYSTEM · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 26-2006. Reason for update: update the Parts list to correct the ambient air temperature service part number. Some vehicles listed in the model statement above may require the replacement of the ambient air temperature sensor for various concerns. DTCs P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM).
Source components: POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Bronco vehicles equipped with a 7 speaker audio system (minor feature code IDBAL) may exhibit diagnostic trouble codes (DTCs) B128A:01, B128A:11, B128A:12, B128A:13, B1288:11, B1288:12 and/or B1238:17 stored in the audio front control module (ACM) with no customer facing symptoms related to those DTCs. Clear the DTCs and if the DTCs return with no customer facing symptoms, this condition may be due to the ACM software. Replacement of the ACM and/or speakers will not resolve this condition. Inform the customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in Q4 2026. Continue to monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If a vehicle exhibits this condition, enter the vehicle identification number (VIN) and click the "Submit Global Concern Report (GCR)" link at the upper right of the PTS "Vehicle ID" screen. Fill out the GCR form, referencing this article number in the report.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 20202026 vehicles equipped with the 10R60 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. Workshop Manual (WSM) updates related to this diagnostic procedure are planned for release in Q4 2026. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification for transmission replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2026 Explorer/Escape/Corsair, 2021-2026 Bronco Sport/Bronco, 2022-2026 Maverick, 2024-2026 Mustang/Ranger/Nautilus vehicles equipped with a 2.0L or 2.3L EcoBoost engine may require removal of the turbocharger wastegate control actuator linkage for various reasons. The Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger - 2.0L/2.3L EcoBoost > Removal and Installation > Wastegate Control Actuator Linkage service procedure been added. In addition, the wastegate actuator rod (9E408), associated retention springs (9342) and retaining clips (00817) have been released as lower-level components to complete the repair without replacing the entire turbocharger wastegate actuator assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Bronco vehicles may exhibit a condition where cruise control is inoperative and/or an "Adaptive Cruise Control Not Available" message is displayed in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U0422:00 stored in the anti-lock brake (ABS) module. If a vehicle exhibits this condition, this may be due to an incorrect configuration programmed to the ABS module during an attempt to change tire size. <br /><br /> The Ford Performance ProCal 4 tool is the only approved tool that can be used for properly adjusting the tire size calibration. Vehicles originally equipped with 30-inch tires that are being upfit with 35-inch tires should be set to 615 revolutions per mile in the Ford Performance ProCal 4 tool under Diagnostics and Tools > Tire/Gear Adjust. Any other concerns related to tire size calibration that exhibit this condition, contact the Ford Performance Techline as outlined in the Ford Performance ProCal 4 tool instructions. <br /><br /> This limitation in tire size calibration is due to the software in the ABS module.
Source components: FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco Raptor vehicles may exhibit a concern where certain selectable drive modes (G.O.A.T. modes) are unavailable after the ABS module receives a software update. Customers may also report that the "Offroad" mode is not visible and/or after switching to the "Baja" or "Rock Crawl" drive modes, the vehicle returns back to "Normal" mode. To correct this condition, download and run the "ABS - Anti-Lock Brake System (ABS) Module Software Update" application using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming use causal part 2005 and labor operations 2219D and 2219D44.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco non-Raptor vehicles may exhibit a concern where certain selectable drive modes (G.O.A.T. modes) are unavailable after the ABS module received a software update. Customers may report that the vehicle is missing the "Mud/Ruts" and/or "Sand" drive mode(s). To correct this condition, download and run the "ABS - Anti-Lock Brake System (ABS) Module Software Update" application using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming use causal part 2005 and labor operations 2219D and 2219D44.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 25-2621. Reason for update: add 2026 model year vehicles and Transit, update the causal part number (15604), update the Service Procedure, update the service labor operations for 2023 F-Super Duty, and add service labor operations for Transit. Some vehicles listed in the Model statement above may exhibit a no crank/no start condition where the customer cannot start their vehicle. The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Bronco vehicles may exhibit various cruise control, pre-collision and/or front stabilizer bar disconnect related warning messages displayed in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U0418:86 stored in the image processing module A (IPMA). DTC U0415:00 may also be stored in the CHCM. <br /><br /> If wheel speed sensor specific DTCs are present in the anti-lock brake (ABS) module and/or warning messages other than those listed above are present, this SSM does not apply. Refer to the Workshop Manual (WSM) for normal diagnostics. <br /><br /> If a vehicle exhibits this condition, carefully inspect the rear wheel speed sensors for correct installation with the rear wheel speed sensor body seated flush against the axle housing. Repair or replace the affected rear wheel speed sensor as needed, clear the DTC, and retest. Refer to WSM, Section 206-09. <br /><br /> This condition does not affect vehicle durability, and additional diagnosis or service is not recommended at this time. Replacement or reprogramming of the IPMA and/or ABS modules will not resolve this
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · SUSPENSION · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 Bronco vehicles may exhibit a wind noise that has been isolated to the hard top front panel seal. An updated part has been released for service (5-door: M2DZ-78503A22-C and 3-door: M2DZ-98503A22-C). Refer to Workshop Manual, Section 501-18B Hard Top > Removal and Installation > Hard Top Front Panel Seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Bronco vehicles built on or before 09-Sep-2025 may require replacement of the ambient air temperature sensor for various concerns. Diagnostic trouble codes (DTC) P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM). A concern has been identified in TSB 26-2006 that previously instructed replacement of the incorrect ambient air temperature sensor for the vehicle application. Monitor Professional Technician System (PTS) for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Bronco vehicles may exhibit various cruise control, pre-collision and/or front stabilizer bar disconnect related warning messages displayed in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U0418:86 stored in the image processing module A (IPMA) and no wheel speed sensor specific DTCs present in the anti-lock brake (ABS) module. DTC U0415:00 may also be stored in the CHCM. If a vehicle exhibits this condition, carefully inspect the rear wheel speed sensors for correct installation with the rear wheel speed sensor body seated flush against the axle housing. Repair or replace the affected rear wheel speed sensor as needed, clear the DTC, and retest. Refer to Workshop Manual (WSM), Section 206-09. If the condition persists, advise the customer that Engineering is working on a software robustness solution that is expected to be available Q2 2026. <br /><br /> This condition does not affect vehicle durability, and additional diagnosis or service is not recommended at this time. Replacement or reprogramming of the IPMA and/or ABS modules will not resolve this condition.
Source components: FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · POWER TRAIN · VEHICLE SPEED CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Bronco, Bronco Sport, F-Super Duty, Maverick, Mustang, Mustang Mach-E, Ranger and Transit vehicles may exhibit a no audio/sound condition. This may be due to the software in the audio control module (ACM). To determine if it is a software concern, disconnect the vehicle's 12-volt battery cables for 10 minutes and reconnect. If the concern is still present, continue with normal diagnostics in Workshop Manual (WSM), Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing and repair as necessary outside of this article. If the no audio/sound concern is resolved, engineering is currently working on a solution for this condition that is expected by September 2026. Replacement or reprogramming of the ACM and or audio digital signal processing module (DSP) may not resolve this condition at this time. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If a customer's vehicle exhibits this concern, submit a Vehicle Concern Report.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Recommended Repair Prior to Sale Customer Satisfaction Program 26P04 Certain 2025 Model Year Bronco and Ranger Vehicles with 2.7L Engine Setting Diagnostic Trouble Code (DTC) P04DB Powertrain Control Module Software Update
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles listed in the model statement above may require the replacement of the ambient air temperature sensor for various concerns. DTCs P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM).
Source components: POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Bronco/Expedition/Navigator/F-150/Ranger vehicles may exhibit a "Check Brake System" message in the instrument panel cluster (IPC) and/or an illuminated anti-lock brake system (ABS) indicator with diagnostic trouble code (DTC) C0563 stored in the ABS module. This may be due to air still trapped in the system after prior bleeding attempts and/or brake service mode being enabled. The applicable pinpoint test (PPT) in Workshop Manual (WSM), Section 206-09 has been updated to improve diagnostics for this concern. Make sure the latest software version of Ford Diagnosis and Repair System (FDRS) is being used when performing the brake system pressure bleeding routine.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
Source components: ELECTRICAL SYSTEM · LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Bronco vehicles may exhibit a "Cruise Control Not Available" or "Adaptive Cruise Control Not Available" and/or "Pre-Collision Assist Not Available" message displayed in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U0418:86 stored in the image processing module A (IPMA) and no DTCs present in the anti-lock brake (ABS) module
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2026 Bronco vehicles that have the dealer installed option (DIO)/accessory trailer tow kit installed may exhibit a condition where the trailer module (TRM) is not detected, or a "Procedure Unsuccessful" message is displayed after running a configuration application using the Ford Diagnosis and Repair System (FDRS) scan tool. This may be due to any of the following issues:<br /><br /> -The FDRS scan tool version is not at the latest software level. To correct this condition, run the "Towbar Configuration" application using the latest software version of the FDRS scan tool.<br /><br /> -The "TRM - Trailer Module (TRM) Configuration" application being run instead of the "Towbar Configuration" application. Accessory TRMs are preprogrammed and only the "Towbar Configuration" application should be run to configure the TRM properly for trailer tow capabilities. Too many attempts to program the TRM using the "TRM - Trailer Module (TRM) Configuration" application may result in a faulted TRM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
Source components: BACK OVER PREVENTION: REARVIEW SYSTEM BRAKING · BACK OVER PREVENTION: WARNINGS · LANE DEPARTURE: BLIND SPOT DETECTION · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025-2026 Bronco Badlands and Raptor only vehicles may exhibit a "Cruise Control Not Available" or "Active Cruise Control Not Available" message displayed in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U0418:86 stored in the image processing module A (IPMA) and no DTCs present in the anti-lock brake (ABS) module.
Source components: ELECTRICAL SYSTEM · VEHICLE SPEED CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco vehicles equipped with a 7-speaker audio system (minor feature code IDBAL) may exhibit an intermittent no audio condition. To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle ID Tab > Vehicle Information, or double-clicking the vehicle identification number (VIN) in the upper left corner on Professional Technician System (PTS). To correct this condition, reprogram the audio front control module (ACM) using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming use causal part 18806 and labor operations 12651D and 12651D4.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 F-150, Expedition/Navigator, Escape/Corsair, Bronco, Explorer, Mustang, Maverick vehicles equipped with a 1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and/or may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the high-pressure fuel pump causing fuel to enter the crankcase and reduce fuel pressure in the direct injection fuel rail. Diagnose this condition using Pinpoint Test HP located in Workshop Manual (WSM), Section 303-04. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. Repair as necessary outside of this article. For claiming, if high-pressure fuel pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article.
Source components: ENGINE · FUEL/PROPULSION SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 20172026 vehicles equipped with a 10R transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco/Ranger vehicles equipped with a 2.7L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04DB stored in the powertrain control module (PCM) with no other relevant DTCs present. This may be due to the software in the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco vehicles may exhibit a condition where the 24-hour clock reverts back to the 12-hour format after each key cycle. This may be due to the software in the accessory protocol interface module (APIM).
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 Bronco vehicles may exhibit a wind noise that has been isolated to the hard top front panel seal. An updated part has been released for service (M2DZ-78503A22-C). Refer to Workshop Manual, Section 501-18B Hard Top > Removal and Installation > Hard Top Front Panel Seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles listed in the Model statement above may exhibit a no crank/no start condition where the customer cannot start their vehicle. The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.
Source components: ELECTRICAL SYSTEM · POWER TRAIN · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco/Ranger vehicles equipped with a 2.7L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04DB stored in the powertrain control module (PCM) with no other relevant DTCs present. Refer to Workshop Manual (WSM), Section 303-08B Engine Emission Control > Diagnosis and Testing > Crankcase Ventilation > Pinpoint Test > steps HG1-3 to check for leaks in the positive crankcase ventilation (PCV) and repair as needed. If no leaks are found in the PCV system, this condition may be due to the software in the PCM. This condition does not affect vehicle durability and no additional diagnosis is required for this condition at this time. The replacement of components or reprogramming of modules will not resolve this condition. Clear the DTC and return the vehicle to the customer. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in Q2 2026. If a vehicle comes in for this condition, submit a Global Concern Report (GCR) and monitor Professional Tech
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes 25-2493 to update the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit a rattle from the right loadspace trim panel at high audio system volumes. This may be due to loose and/or broken attachments.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco vehicles equipped with a 7 speaker audio system (minor feature code IDBAL) may exhibit diagnostic trouble codes (DTCs) B128A:01, B128A:11, B128A:12, B128A:13, B1288:11, B1288:12 and/or B1238:17 stored in the audio front control module (ACM). To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle ID Tab > Vehicle Information, or double-clicking the vehicle identification number (VIN) in the upper left corner on Professional Technician System (PTS). Clear the DTCs and if the DTCs return with no customer facing symptoms, this condition may be due to the ACM software. Replacement of the ACM and/or speakers will not resolve this condition. Inform the customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in Q2 2026. Continue to monitor PTS for additional information and schedule service appointments for customers once the repair becomes available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco vehicles equipped with a 7-speaker audio system (minor feature code IDBAL) may exhibit an intermittent no audio condition. To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle ID Tab > Vehicle Information, or double-clicking the vehicle identification number (VIN) in the upper left corner on Professional Technician System (PTS). To correct this condition, disconnect the negative battery cable and wait two minutes before reconnecting to temporarily restore audio. Inform the customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in Q2 2026. Continue to monitor PTS for additional information and schedule service appointments for customers once the repair becomes available.
Source components: ELECTRICAL SYSTEM · FUEL/PROPULSION SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco/Ranger vehicles equipped with a 2.3L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with only diagnostic trouble codes (DTCs) P0300 and P0316 stored in the powertrain control module (PCM). This condition occurs after initial engine start up following an overnight cold soak or short cold soak (2-3 hours). This condition does not affect vehicle durability and no additional diagnosis is required for this condition at this time. The replacement of components or reprogramming of modules will not resolve this condition. Clear the DTCs and return the vehicle to the customer. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in Q2 2026. Continue to monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2104 to update the vehicle model years affected. Some vehicles listed in the Model statement above may exhibit a "Sta-bar Disconnect Service Required" message in the instrument panel cluster (IPC) and an illuminated warning light with any of the following diagnostic trouble codes (DTCs) stored in the chassis control module (CHCM): C103A, C1A99, C1B03, C1B07, C1B14 and/or B1A67. This may be due to water intrusion in the stabilizer bar wiring harness connector.
Source components: ELECTRICAL SYSTEM · SUSPENSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the model statement above may exhibit paint wearing along on the top inner edge of the tailgate where the rear window weather strip contacts the tailgate. This may be due to the accumulation of dirt between the rear window seal and tailgate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The affected 2025 Model Year Bronco Big Bend and Badlands vehicles had an incorrect Manufacturer’s Suggested Retail Price (MSRP) listed on their Monroney Labels and incorrectly included optional pricing. The Monroney Labels erroneously listed equipment groups 222A (Big Bend) and 332A (Badlands) as optional content on these Job 1 vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Bronco vehicles may exhibit an illuminated red brake warning indicator with diagnostic trouble code (DTC) C0049:01 stored in the anti-lock brake system (ABS) module. Replace the brake fluid reservoir and the brake fluid level sensor electrical connector. Do not disconnect the brake fluid level sensor electrical connector, cut the connector 3-4 inches (75-100 mm) from the connector end and leave the brake fluid level sensor electrical connector attached to brake fluid reservoir. Include these parts in the same package when returning warranty replacement brake fluid reservoirs. The brake fluid reservoir with the electrical connector still connected should be packaged in the original box to protect it during shipping. For claiming, use causal part 2L210 and labor operations 2140A and 2219D45WR.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit a rattle from right loadspace trim panel at high audio system volumes. This may be due to loose and/or broken attachments.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2025 various Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
Source components: ELECTRICAL SYSTEM · LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 Escape Hybrid/Maverick Hybrid/Nautilus Hybrid/F-150 non-Lightning/F-Super Duty/Bronco and 2025 Expedition/Navigator/Ranger vehicles where customers have installed an aftermarket supplemental braking system may experience a discharged 12-volt battery after recreational towing. This may be due to the supplemental braking system keeping the vehicle awake during brake applications. Advise customers that while recreational towing the vehicle with a supplemental braking system installed, it is recommended to use a 12-volt battery charger connected to a power source external to the vehicle being towed. The Owners Manual is in process of being updated with this information.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2269 to add 2025 model year vehicles. Some of the vehicles listed in the Model statement above may exhibit the driver or passenger side upper rail front trim panel with a warped or misaligned appearance.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Harvest Program 25H03 Certain 2024 - 2025 Model Year Bronco, Bronco Sport, Corsair, Escape, Explorer, Maverick, Mustang, and Ranger Vehicles with 1.5L, 2.0L, or 2.3L Engine Spark Plug Replacemen
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2024 - 2025 Model Year Bronco, Bronco Sport, Corsair, Escape, Explorer, Maverick, Mustang, and Ranger Vehicles with 1.5L, 2.0L, or 2.3L Engine Spark Plug Replacement
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco vehicles equipped with a 7 speaker audio system (minor feature code IDBAL) may exhibit an intermittent no audio condition and/or speaker fault with diagnostic trouble codes (DTCs) B128A:01, B128A:11, B128A:12, B128A:13, B1288:11, B1288:12 and/or B1238:17 stored in the audio control module (ACM). To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle ID Tab > Vehicle Information, or double-clicking the vehicle identification number (VIN) in the upper left corner on Professional Technician System (PTS). To correct this condition, disconnect the negative battery cable and wait two minutes before reconnecting. If the no audio condition is not resolved, refer to the Workshop Manual (WSM), Section 415-00 for normal diagnostics outside of this article. If the no audio condition is resolved and the DTCs remain, this concern may be due to the ACM software. Replacement of the ACM and/or speakers will not resolve this condition. Inform the customers that they can continue to drive the vehicle and engineering
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 F-150, Expedition/Navigator, Escape/Corsair, Bronco, Explorer, Mustang, Maverick vehicles equipped with a 1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the fuel injection pump causing fuel to enter the crankcase and reduce fuel pressure in the high pressure fuel rail. Diagnose this condition using Pinpoint Test HP located in the Workshop Manual, Section 303-04A. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. For claiming, if fuel injection pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article. Note: Components damaged as a result of this failure mode
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit an air register that is broken or loose. This may be due to the register barrel detaching from the register assembly. Removal of the instrument panel is no longer required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Ford and Lincoln vehicles equipped with SYNC4/Digital Experience may exhibit an unsuccessful telematics control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2025 Model Year Bronco, Explorer, Mustang, and Ranger Vehicles Engine Coolant Temperature Sensor Replacement On all affected vehicles, the Engine Coolant Temperature sensor (ECT) may have a poor solder joint internally, causing a Diagnostic Trouble Code (DTC) to set against the sensor for an open circuit and the check engine light to illuminate
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 Bronco vehicles equipped with a painted hard top may exhibit a strong plastic odor inside the cabin coming from the painted hard top during high temperatures and/or after extended periods of sun exposure. This is part of the normal material break-in process for the removable roof panels. This break-in process can be accelerated through exposure to heat over time such as leaving the vehicle parked in direct sunlight on warm days. To dissipate the odor, instruct customers to use air conditioning with the recirculate function off and/or open the side windows to vent the interior cabin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Bronco and 2024-2025 Ranger vehicles equipped with a 2.7L/3.0L EcoBoost engine may require removal of the engine front cover due to various concerns. Workshop Manual, Section 303-01 has been updated with improved engine front cover removal and installation service procedure steps including a new body removal and install step.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco vehicles equipped with a 2.3/2.7L EcoBoost engine built on or before 12-June-2025 and 2025 Bronco Raptor vehicles equipped with a 3.0L EcoBoost engine built on or before 18-June-2025 may exhibit various illuminated brake system warning lamps/fault messages at start up with diagnostic trouble codes (DTCs) C003A:4A, C003A:64, C0037:4A, C0037:64, C2005:1D, C2005:78, C2006:1D, and/or C2006:78 stored in the anti-lock brake system (ABS) module. To correct this condition, reprogram the ABS module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 2005 and labor operations 2219D and 2219D44 in Section 02 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco vehicles equipped with a 2.3/2.7L EcoBoost engine built on or before 12-June-2025 and 2025 Bronco Raptor vehicles equipped with a 3.0L EcoBoost engine built on or before 18-June-2025 may exhibit an illuminated anti-lock brake system (ABS) warning indicator with diagnostic trouble code (DTC) U3012:68 stored in the ABS module. The vehicle may also exhibit any of the following symptoms: a soft brake pedal following vehicle start-up, various brake system illuminated warning lamps and/or brake-related messages displayed in the instrument panel cluster (IPC). This may be due to a controller area network (CAN) communication concern within the ABS module. To correct the condition, reprogram the ABS module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 2005 and labor operations 2219D and 2219D44 in Section 02 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Edge/Nautilus, 2021-2025 Bronco/Bronco Sport/E-Series/Escape/Corsair/Expedition/Navigator/Explorer/Aviator/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2023-2025 Escape vehicles equipped with a 1.5L/2.0L EcoBoost engine, 2023-2025 Corsair vehicles equipped with a 2.0L EcoBoost engine, 2024-2025 Nautilus vehicles equipped with a 2.0L EcoBoost engine, 2024-2025 Mustang vehicles with a 2.3L EcoBoost engine, and 2025 Bronco/Explorer/Ranger vehicles equipped with a 2.3L EcoBoost engine may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM). This may be due to the spark plugs and/or ignition coils. To correct the condition, refer to Workshop Manual (WSM), Section 303-07 for normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Bronco vehicles may exhibit a water leak from the A-pillar, overhead console/upfitter switches and/or sun visors. If a leak is identified from this area, refer to Workshop Manual (WSM), Section 501-18 Pinpoint Test (PPT) G for water leak diagnosis. If the PPT leads to the replacement of the header seal, a revised header seal has been released for service (M2DZ-7803110-H) which contains a thicker consistent bead of butyl across the entire length of the seal. The header seal will need to be firmly depressed and massaged to make sure all of the butyl that is across the entire header seal will properly adhere to the body, creating a water-tight seal. For claiming, use causal part 7803110 and labor operation 03110A in Section 12 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco and Ranger vehicles may exhibit various illuminated brake system warning lamps/fault messages at start up with diagnostic trouble codes (DTCs) C003A:4A, C003A:64, C0037:4A, C0037:64, C2005:1D, C2005:78, C2006:1D, and/or C2006:78 stored in the antilock brake system (ABS) module. To correct this condition, clear the DTCs, turn the ignition off and then back on, engage and disengage the park brake and then run a self-test. If any DTCs return, refer to the Workshop Manual (WSM) for normal diagnosis. If the DTCs clear, this concern may be due to the ABS software and replacement of the ABS module or wheel speed sensors will not resolve this condition. Inform the customers they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in Q3 of 2025. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco vehicles may exhibit an illuminated anti-lock brake system (ABS) warning indicator with diagnostic trouble code (DTC) U3012:68 stored in the ABS module. The vehicle may also exhibit any of the following symptoms: a soft brake pedal following vehicle start-up, various brake system illuminated warning lamps and/or brake-related messages displayed in the instrument panel cluster (IPC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit a wind noise that has been isolated to the hard top front panel panel-to-panel seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers with recently delivered Bronco vehicles may experience a harsh ride due to excessive tire pressure not being adjusted during the pre-delivery process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit an incorrectly illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1299, P1026, and P2C39.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 F-150/Expedition/Navigator/Bronco/Ranger vehicles may exhibit diagnostic trouble code (DTC) U3012:68 stored in the anti-lock brake system (ABS) module with a soft brake pedal following vehicle start-up with various brake system illuminated warning lamps and/or brake-related messages displayed in the instrument panel cluster (IPC). This may be due to a controller area network (CAN) communication concern within the ABS module. Replacement of the ABS module will not resolve this condition. To resolve this condition, place the vehicle in park. Disengage the park brake. Turn the vehicle off. Close all doors and liftgate/tailgate. Allow the vehicle to sit for 5 minutes to allow all vehicle modules to power down. Restart the vehicle. Verify brake functionality and clear any DTCs. Pressing unlock/lock button on the key fob, opening the doors/liftgate/tailgate or keeping the key fob within 30 ft (8 meters) of the vehicle can prevent the modules from powering down completely. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco vehicles may exhibit diagnostic trouble code (DTC) U0137 stored in the instrument panel cluster (IPC) after installation of the dealer installed option (DIO) trailer tow package. To correct this condition, download and run the latest version of the towbar configuration application using the latest version of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 15A416 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2025 Bronco vehicles may exhibit a "procedure unsuccessful" message after running the towbar configuration application using Ford Diagnosis and Repair System (FDRS) scan tool. This may be due to the incorrect trailer tow kit being installed. Trailer modules (TRM) are model year specific. A 2024 Bronco requires the installation of trailer tow kit VP2DZ-15A416-B and a 2025 Bronco requires the installation of trailer tow kit VS2DZ-15A416-C.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2077 to update the model years affected. Some of the vehicles listed in the Model statement above may a exhibit a factory soft top headliner that is detaching from the soft top material. This may be due to the factory installation process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 Bronco vehicles equipped with a dealer installed trailer tow kit may exhibit a "No Key Detected" message displayed in the IPC. This may be due to the remote keyless entry (RKE) antenna connection being left loose or disconnected during trailer tow kit installation. Verify that the vehicle is equipped with the trailer tow kit by checking the window sticker for the trailer tow kit option. If the vehicle was equipped with this dealer installed option, before performing normal diagnostics, inspect the RKE antenna connections located behind the left/rear interior quarter panel. If they are loose or unplugged, re-secure the connector(s) and retest operation. If no loose or unplugged connections are found, refer to Workshop Manual (WSM), Section 419-01 for normal diagnostics. If this vehicle does not have the dealer installed option, refer to the WSM, Section 419-01 for normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Drivers of some 2020-2025 Escape, 2021-2025 Bronco Sport and 2022-2025 Maverick vehicles may report the uncommanded locking of the driver door after the door is closed. This may be due to the driver placing their hand on the interior front door handle and inadvertently pushing the manual door lock toggle into the lock position. If the lock and latching mechanisms are functioning normally, and if there are no related diagnostic trouble codes (DTCs) or other issues identified, then the system is operating as designed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2025 Ford or Lincoln vehicles may exhibit DTCs B142E:78, B1432:78, and/or B1433:54 diagnostic trouble codes (DTCs) in the CCM. This may be due to non-factory sized tires that may cause inaccurate speedometer readings that can impact the functionality of the CCM. When a vehicle is modified in this manner, replacement or realignment of the CCM may impact the normal operation of the system and/or performance of radar and camera-based features. Repair or replacement of the CCM when a vehicle is equipped with non-factory size tires may not be warrantable and subject to chargeback.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2025 Bronco vehicles are equipped with an added strategy within the short drop feature which will activate anytime the vehicle is unlocked using the remote keyless entry (RKE), accessory keyless entry keypad, or the interior door unlock switch.