2024 Ford BRONCO Manufacturer communications & TSBs.Page 1
Original record summaries, dates and identifiers for this model-year. Records 1–100 of 131, ordered newest first. Dated records on this page: Aug 2, 2024–Aug 25, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Aug 25, 2026Service Bulletin/Repair Instructions
SSM 55118
NHTSA communication ID: 11036529
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the following vehicles: * 2023-2025 F-Super Duty built on or before 02-Feb-2025 * 2024-2026 Ranger/Bronco/Mustang * 2024-2025 F-150 built on or before 15-Jul-2025 * 2024-2025 Nautilus built on or before 16-Feb-2025 * 2025 Explorer/Aviator built on or before 01-Feb-2025 may exhibit all of the following symptoms: - "No Key Detected" message displayed on the instrument panel cluster (IPC). - Key fob does not work in the backup slot. - Remote keyless entry (RKE) (lock and unlock from the key fob) functionality will work to lock/unlock the vehicle. If the vehicle exhibits these symptoms, start the vehicle using both key fobs. If the no crank/no start condition with "No Key Detected" concern is present, reprogram both key fobs and retest. If the no crank/no start condition with "No Key Detected" is still present, replace the body control module (BCM). Refer to Workshop Manual (WSM), Section 419-10. For claiming, use causal part 15604 and labor operation MT55118SSM up to 1.8 hours.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For Various Ford and Lincoln vehicles, if diagnostics lead to the replacement of the front seat cushion cover J-clips, lower-level service parts are now available. Use service part W709919-S901 if the J-clip is completely detached from the seat cover and W715386-S424 if the clip is still partially attached. It is not necessary to replace the seat cover if only the J-clip is separating from the cover. Refer to PTS Home > Technical Assistance > Technical Support Videos > Section 501- Body and Paint > Seat J-Clips. For claiming, use causal parts from list below and labor operations 63100A and 63100A5. Causal Parts for claiming: Bronco/Bronco Sport/Escape/Explorer/Expedition/Navigator: 7862900 or 7862901 F-150/F-Super Duty: 1562900 or 1562901 Ranger/Maverick: 6062900 or 6062901
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 Bronco vehicles may require the removal and installation of the transfer case for various reasons. Installation requires Loctite® 243 adhesive applied to the mounting bolt threads in the transmission. Make sure that the mating faces are clean and dry. Tightening the mounting bolts also requires an updated two-stage tightening sequence. Workshop Manual (WSM), Sections 307-07C/D and 308-07C/D Installation > Transfer Case have been updated to reflect this change.
Source components: POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
Source components: ELECTRICAL SYSTEM · FUEL/PROPULSION SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Ford and Lincoln vehicles may exhibit an "Updating SYNC" message on the vehicle center display screen after an over the air (OTA) update. The message can be cleared from the center display screen and SYNC can be used normally, but it will re-appear at every subsequent ignition cycle. Inform customers that engineering is currently working on a software update solution for this condition to be delivered OTA expected in late Q3 2026. Software will update automatically if vehicle connectivity is enabled in the vehicles settings. Monitor Professional Technician System (PTS) for additional information.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 Bronco vehicles may exhibit a "Park Brake Limited Function Service Required" message in the instrument panel cluster (IPC). This may be due to an issue with the driver door harness connector after removing and installing the removeable doors. If diagnostic trouble code (DTC) B1625:29 is stored in the driver door module (DDM), inspect connector C322C between the upper and lower door hinges that attaches to the body for proper installation and/or pin fitment. Repair as necessary. If the condition was caused by improper door installation, do not submit a claim for this condition. If no concerns are found with the connector, refer to Workshop Manual (WSM), Section 501-11 > Diagnosis and Testing for normal diagnostics.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NEW VEHICLE DELIVERY HOLD - Emissions Recall 26E04 Certain 2021-2025 Model Year F-150, Maverick, Mustang, Ranger, Expedition, Bronco Sport, Explorer, Bronco, Navigator, and Aviator Vehicles Powertrain Control Module Software Update
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2026 Bronco vehicles may exhibit various TRM concerns when attempting first time installation of a dealer installed accessory TRM, including one or more of the following: TRM unable to be programmed -Trailer lights inoperative -DTC U2100 stored in the TRM. This may be due to any of the following conditions:-The incorrect trailer tow kit is being installed. The TRM is model year specific. Refer to the parts catalog using the VIN and base part number 15A416 for the vehicle specific trailer tow kit.-The "TRM - Trailer Module (TRM) Configuration" application being run instead of the "Towbar Configuration" application during first time TRM installation using the Ford Diagnosis and Repair System (FDRS). Dealer installed accessory TRMs are preprogrammed and only the "Towbar Configuration" application should be run during first time TRM installation to configure the TRM properly and support proper function of trailer tow capabilities. Any attempts to program the TRM using the "TRM - Trailer Module (TRM) Configuration" application a
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes 25-2551. Reason for update: to correct the descriptions for the liftgate glass weather seals. Some of the vehicles listed in the model statement above may exhibit paint wearing along on the top inner edge of the tailgate where the rear window weather strip contacts the tailgate. This may be due to the accumulation of dirt between the rear window seal and tailgate.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2026 Bronco vehicles may exhibit a condition where short drop windows, window bounce-back, and/or one-touch open/close does not operate properly. This may be due to loss of window initialization. Replacement or reprogramming of the DDM, PDM, and/or any other components may not resolve these conditions. The short drop windows feature may be restored by performing a reset procedure as described in the Digital Owner's Manual > Windows > Using Short Drop Windows > Resetting Short Drop Windows. If the customer is experiencing an inability to fully close the window due to repeated bounce-back events, the window bounce-back feature may be overridden by performing an override procedure as described in the Digital Owner's Manual > Windows > Window Bounce-Back > Overriding Windows Bounce-Back. The one-touch open/close feature may be restored by performing a reset procedure as described in the Digital Owner's Manual > Windows > Opening and Closing the Windows > Resetting Window One-Touch. These symptoms may return after a successful reset/override
Source components: ELECTRICAL SYSTEM · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 26-2006. Reason for update: update the Parts list to correct the ambient air temperature service part number. Some vehicles listed in the model statement above may require the replacement of the ambient air temperature sensor for various concerns. DTCs P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM).
Source components: POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 20202026 vehicles equipped with the 10R60 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. Workshop Manual (WSM) updates related to this diagnostic procedure are planned for release in Q4 2026. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification for transmission replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Engine misfire condition * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0301, P0302, P0303, and/or P0304 stored in the powertrain control module (PCM)
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2026 Explorer/Escape/Corsair, 2021-2026 Bronco Sport/Bronco, 2022-2026 Maverick, 2024-2026 Mustang/Ranger/Nautilus vehicles equipped with a 2.0L or 2.3L EcoBoost engine may require removal of the turbocharger wastegate control actuator linkage for various reasons. The Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger - 2.0L/2.3L EcoBoost > Removal and Installation > Wastegate Control Actuator Linkage service procedure been added. In addition, the wastegate actuator rod (9E408), associated retention springs (9342) and retaining clips (00817) have been released as lower-level components to complete the repair without replacing the entire turbocharger wastegate actuator assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Bronco vehicles equipped with a manual transmission may experience a rotational scraping noise while the transmission is in neutral, 1st and/or 2nd gear with the clutch pedal released. The noise may be more noticeable in ambient temps below 10°C (50°F) and after a cold soak. This noise may also diminish as the transmission warms up. This may be due to the 5th and 6th gear synchronizer rings. The 5th and 6th gear synchronizer rings are now only available in the 6th/5th gear synchronizer assembly (service part number MU7Z-7124-Q). To correct the condition, replace the 6th/5th gear synchronizer. Remove the transmission from the vehicle. Refer to Workshop Manual (WSM), Section 308-03 > Removal. Disassemble the transmission. Refer to WSM, Section 308-03 > Disassembly. Disassemble the input shaft to gain access to the 6th/5th gear synchronizer. Refer to WSM, Section 308-03 > Disassembly and Assembly of Subassemblies > Input Shaft. Replace the 6th/5th gear synchronizer and assemble the input shaft. Assemble the transmission. Refer to WSM, Section 308-03 > Assembly. Install the transmission.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021-2024 Model Year Bronco, 2021-2024 Model Year Bronco Sport, 2020-2022 Model Year Corsair and Escape, 2016-2024 Model Year Explorer, 2019-2020 Model Year Fusion, 2016-2018 Model Year Focus RS, 2022-2024 Model Year Maverick, 2016-2019 Model Year MKC and 2019-2024 Model Year Ranger Vehicles Equipped with a 2.0L or 2.3L Engine and Engine Block Heater System Block Heater Replacement
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 25-2621. Reason for update: add 2026 model year vehicles and Transit, update the causal part number (15604), update the Service Procedure, update the service labor operations for 2023 F-Super Duty, and add service labor operations for Transit. Some vehicles listed in the Model statement above may exhibit a no crank/no start condition where the customer cannot start their vehicle. The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 Bronco vehicles may exhibit a wind noise that has been isolated to the hard top front panel seal. An updated part has been released for service (5-door: M2DZ-78503A22-C and 3-door: M2DZ-98503A22-C). Refer to Workshop Manual, Section 501-18B Hard Top > Removal and Installation > Hard Top Front Panel Seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Bronco vehicles built on or before 09-Sep-2025 may require replacement of the ambient air temperature sensor for various concerns. Diagnostic trouble codes (DTC) P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM). A concern has been identified in TSB 26-2006 that previously instructed replacement of the incorrect ambient air temperature sensor for the vehicle application. Monitor Professional Technician System (PTS) for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles listed in the model statement above may require the replacement of the ambient air temperature sensor for various concerns. DTCs P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM).
Source components: POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
Source components: ELECTRICAL SYSTEM · LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2026 Bronco vehicles that have the dealer installed option (DIO)/accessory trailer tow kit installed may exhibit a condition where the trailer module (TRM) is not detected, or a "Procedure Unsuccessful" message is displayed after running a configuration application using the Ford Diagnosis and Repair System (FDRS) scan tool. This may be due to any of the following issues:<br /><br /> -The FDRS scan tool version is not at the latest software level. To correct this condition, run the "Towbar Configuration" application using the latest software version of the FDRS scan tool.<br /><br /> -The "TRM - Trailer Module (TRM) Configuration" application being run instead of the "Towbar Configuration" application. Accessory TRMs are preprogrammed and only the "Towbar Configuration" application should be run to configure the TRM properly for trailer tow capabilities. Too many attempts to program the TRM using the "TRM - Trailer Module (TRM) Configuration" application may result in a faulted TRM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
Source components: BACK OVER PREVENTION: REARVIEW SYSTEM BRAKING · BACK OVER PREVENTION: WARNINGS · LANE DEPARTURE: BLIND SPOT DETECTION · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 20172026 vehicles equipped with a 10R transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 Bronco vehicles may exhibit a wind noise that has been isolated to the hard top front panel seal. An updated part has been released for service (M2DZ-78503A22-C). Refer to Workshop Manual, Section 501-18B Hard Top > Removal and Installation > Hard Top Front Panel Seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles listed in the Model statement above may exhibit a no crank/no start condition where the customer cannot start their vehicle. The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.
Source components: ELECTRICAL SYSTEM · POWER TRAIN · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes 24-2387 to update the Parts List, Service Procedure enhancements, and labor operation allowances in place of M-time. Some of the vehicles listed in the Model statement above equipped with a factory subwoofer may exhibit a rattle from right loadspace trim panel at high audio system volumes. This may be due to lose and/or broken attachments.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2408 to update the parts list. Some of the vehicles listed in the Model statement above may exhibit a loud front end clink/clunk noise that leads to the identification of a cracked or broken front differential frame mount bracket. This may be due to flexing of the front differential from driving in 4L for extended periods of time. Note: Advise the customer that 4L/Rock Crawl drive mode should only be used when necessary, as using 4L when not necessary can cause damage to the vehicle. Refer to the Owner's Manual for additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Bronco vehicles may exhibit an illuminated red brake warning indicator with diagnostic trouble code (DTC) C0049:01 stored in the anti-lock brake system (ABS) module. Replace the brake fluid reservoir and the brake fluid level sensor electrical connector. Do not disconnect the brake fluid level sensor electrical connector, cut the connector 3-4 inches (75-100 mm) from the connector end and leave the brake fluid level sensor electrical connector attached to brake fluid reservoir. Include these parts in the same package when returning warranty replacement brake fluid reservoirs. The brake fluid reservoir with the electrical connector still connected should be packaged in the original box to protect it during shipping. For claiming, use causal part 2L210 and labor operations 2140A and 2219D45WR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2104 to update the vehicle model years affected. Some vehicles listed in the Model statement above may exhibit a "Sta-bar Disconnect Service Required" message in the instrument panel cluster (IPC) and an illuminated warning light with any of the following diagnostic trouble codes (DTCs) stored in the chassis control module (CHCM): C103A, C1A99, C1B03, C1B07, C1B14 and/or B1A67. This may be due to water intrusion in the stabilizer bar wiring harness connector.
Source components: ELECTRICAL SYSTEM · SUSPENSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the model statement above may exhibit paint wearing along on the top inner edge of the tailgate where the rear window weather strip contacts the tailgate. This may be due to the accumulation of dirt between the rear window seal and tailgate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Bronco vehicles may exhibit an illuminated red brake warning indicator with diagnostic trouble code (DTC) C0049:01 stored in the anti-lock brake system (ABS) module. Replace the brake fluid reservoir and the brake fluid level sensor electrical connector. Do not disconnect the brake fluid level sensor electrical connector, cut the connector 3-4 inches (75-100 mm) from the connector end and leave the brake fluid level sensor electrical connector attached to brake fluid reservoir. Include these parts in the same package when returning warranty replacement brake fluid reservoirs. The brake fluid reservoir with the electrical connector still connected should be packaged in the original box to protect it during shipping. For claiming, use causal part 2L210 and labor operations 2140A and 2219D45WR.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2025 various Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
Source components: ELECTRICAL SYSTEM · LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Explorer vehicles equipped with a 3.0L EcoBoost engine, 2021-2023 Aviator vehicles equipped with a 3.0L EcoBoost or 3.0L plug-in hybrid electric vehicle (PHEV) engine, 2021-2023 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost, 2021-2024 F-150 vehicles equipped with a 2.7L EcoBoost, and 2021-2024 Bronco and 2024 Ranger vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine. This noise may occur on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to an internal component of the variable cam timing (VCT) unit. Workshop Manual (WSM), Section 303-00 > Diagnosis and Testing > Engine > Pinpoint Test F has been updated to include additional steps along with a video to identify the affected VCT unit that requires replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 Escape Hybrid/Maverick Hybrid/Nautilus Hybrid/F-150 non-Lightning/F-Super Duty/Bronco and 2025 Expedition/Navigator/Ranger vehicles where customers have installed an aftermarket supplemental braking system may experience a discharged 12-volt battery after recreational towing. This may be due to the supplemental braking system keeping the vehicle awake during brake applications. Advise customers that while recreational towing the vehicle with a supplemental braking system installed, it is recommended to use a 12-volt battery charger connected to a power source external to the vehicle being towed. The Owners Manual is in process of being updated with this information.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2269 to add 2025 model year vehicles. Some of the vehicles listed in the Model statement above may exhibit the driver or passenger side upper rail front trim panel with a warped or misaligned appearance.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Harvest Program 25H03 Certain 2024 - 2025 Model Year Bronco, Bronco Sport, Corsair, Escape, Explorer, Maverick, Mustang, and Ranger Vehicles with 1.5L, 2.0L, or 2.3L Engine Spark Plug Replacemen
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2024 - 2025 Model Year Bronco, Bronco Sport, Corsair, Escape, Explorer, Maverick, Mustang, and Ranger Vehicles with 1.5L, 2.0L, or 2.3L Engine Spark Plug Replacement
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit an air register that is broken or loose. This may be due to the register barrel detaching from the register assembly. Removal of the instrument panel is no longer required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Ford and Lincoln vehicles equipped with SYNC4/Digital Experience may exhibit an unsuccessful telematics control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 Bronco vehicles equipped with a painted hard top may exhibit a strong plastic odor inside the cabin coming from the painted hard top during high temperatures and/or after extended periods of sun exposure. This is part of the normal material break-in process for the removable roof panels. This break-in process can be accelerated through exposure to heat over time such as leaving the vehicle parked in direct sunlight on warm days. To dissipate the odor, instruct customers to use air conditioning with the recirculate function off and/or open the side windows to vent the interior cabin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Bronco and 2024-2025 Ranger vehicles equipped with a 2.7L/3.0L EcoBoost engine may require removal of the engine front cover due to various concerns. Workshop Manual, Section 303-01 has been updated with improved engine front cover removal and installation service procedure steps including a new body removal and install step.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Bronco vehicles may exhibit a rattle from the front windows with the windows placed in the partially down position and driving over rough roads and/or bumps. This may be due to the interface between the window glass and the body mounted glass run. To correct this condition, replace the body mounted glass runs using the body mounted glass run kit (3 door: M2DZ-9821597-E, and 5 door: M2DZ-7821597-F) which contains updated seals for improved sealing performance. For claiming, use causal part 9821597/7821597 and labor operations 23943A and 23943A19 in Section 12 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Edge/Nautilus, 2021-2025 Bronco/Bronco Sport/E-Series/Escape/Corsair/Expedition/Navigator/Explorer/Aviator/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Bronco vehicles may exhibit a water leak from the A-pillar, overhead console/upfitter switches and/or sun visors. If a leak is identified from this area, refer to Workshop Manual (WSM), Section 501-18 Pinpoint Test (PPT) G for water leak diagnosis. If the PPT leads to the replacement of the header seal, a revised header seal has been released for service (M2DZ-7803110-H) which contains a thicker consistent bead of butyl across the entire length of the seal. The header seal will need to be firmly depressed and massaged to make sure all of the butyl that is across the entire header seal will properly adhere to the body, creating a water-tight seal. For claiming, use causal part 7803110 and labor operation 03110A in Section 12 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Bronco vehicles built on or before 01-Jan-2025 equipped with a 2.3L EcoBoost engine and 10R60 automatic transmission may exhibit diagnostic trouble codes (DTCs) P0300, P0301, P0302, P0303, and P0304 and may be accompanied by a buck/jerk sensation while driving between 35-55 mph (56-89 km/h) in gears 7-10. If the condition remains after normal engine misfire diagnostics and associated repairs have been performed, the condition may be related to driveline torsional vibration induced by the rear wheels and/or rear axle assembly. The driveline torsional harmonics/vibrations are incorrectly identified by the misfire monitor as an engine misfire. Perform standard road force wheel balancing of all four tire and wheel assemblies and retest. If the condition continues to occur, replace the ring and pinion gearset in the rear axle. For claiming, use causal part 4209 and applicable labor operations found in Section 04 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit a wind noise that has been isolated to the hard top front panel panel-to-panel seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit a repeat loss of window initialization which results in a loss of short drop and/or one-touch up and one-touch down feature operation. This may be due to a recent short drop enhancement that is contained in the driver door module (DDM) and passenger door module (PDM) software.
Source components: ELECTRICAL SYSTEM · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit an incorrectly illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1299, P1026, and P2C39.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Bronco vehicles may exhibit paint wearing along on the top inner edge of the tailgate where the rear window weather strip contacts the tailgate. This may be due to the accumulation of dirt between the rear window seal and tailgate. Inform customers that engineering is aware of this condition and is currently working on a solution which is expected in Q3 2025. Schedule a service visit for customers when the repair is available in Q3 2025. Monitor OASIS for additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2077 to update the model years affected. Some of the vehicles listed in the Model statement above may a exhibit a factory soft top headliner that is detaching from the soft top material. This may be due to the factory installation process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 Bronco vehicles equipped with a dealer installed trailer tow kit may exhibit a "No Key Detected" message displayed in the IPC. This may be due to the remote keyless entry (RKE) antenna connection being left loose or disconnected during trailer tow kit installation. Verify that the vehicle is equipped with the trailer tow kit by checking the window sticker for the trailer tow kit option. If the vehicle was equipped with this dealer installed option, before performing normal diagnostics, inspect the RKE antenna connections located behind the left/rear interior quarter panel. If they are loose or unplugged, re-secure the connector(s) and retest operation. If no loose or unplugged connections are found, refer to Workshop Manual (WSM), Section 419-01 for normal diagnostics. If this vehicle does not have the dealer installed option, refer to the WSM, Section 419-01 for normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Drivers of some 2020-2025 Escape, 2021-2025 Bronco Sport and 2022-2025 Maverick vehicles may report the uncommanded locking of the driver door after the door is closed. This may be due to the driver placing their hand on the interior front door handle and inadvertently pushing the manual door lock toggle into the lock position. If the lock and latching mechanisms are functioning normally, and if there are no related diagnostic trouble codes (DTCs) or other issues identified, then the system is operating as designed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2025 Ford or Lincoln vehicles may exhibit DTCs B142E:78, B1432:78, and/or B1433:54 diagnostic trouble codes (DTCs) in the CCM. This may be due to non-factory sized tires that may cause inaccurate speedometer readings that can impact the functionality of the CCM. When a vehicle is modified in this manner, replacement or realignment of the CCM may impact the normal operation of the system and/or performance of radar and camera-based features. Repair or replacement of the CCM when a vehicle is equipped with non-factory size tires may not be warrantable and subject to chargeback.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * General system performance/stability/intermittent system reboot * Intermittent wireless CarPlay or Android Auto function * Phone related concerns with intermittent no audio or static * Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto * Alexa function consistency and stability * Charge Assist/Public Charging app inoperative (e-Transit only) This may be due to a concern with the software in the accessory protocol interface module (APIM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024 Bronco vehicles built on and after 23-Jul-2024 may exhibit a concern where the vehicle intermittently will not shift out of park in cold weather conditions with diagnostic trouble code (DTC) B1319 stored in the body control module (BCM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2025 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2024 F-150/Edge, 2018 MKX, 2019-2023 Nautilus, 2020-2025 Explorer/Aviator, 2021-2024 Bronco, and 2024 Ranger vehicles equipped with a 2.7L or a 3.0L EcoBoost engine may exhibit an engine oil leak from the crankshaft rear seal with retaining plate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Bronco vehicles equipped with a 2.3L/2.7L engine may exhibit a loud front end clink/clunk noise that leads to the identification of a cracked or broken front differential frame mount bracket.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024 Bronco vehicles may be unable to program the trailer brake module (TRM) during installation of the dealer installed option/accessory "Trailer Tow Kit".
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs. Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 Bronco vehicles built on or before 13-Feb-2024 equipped with a 3.0L EcoBoost engine and 2021-2024 Broncos equipped with a 2.3L EcoBoost engine may exhibit an illuminated MIL with ignition system DTCs P0352, P0353, P0354, P0355, P2303, P2306, P2309, P2312, P2304, P2307, P2310, and/or P2313 set in the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
One of the two keys provided with the vehicle may not have been successfully programmed during production. A key that was not successfully programmed will not start the vehicle. A No Key Detected message will display in the instrument panel cluster when attempting to start the vehicle with an unprogrammed key. The physical buttons on the affected key fob will lock and unlock the doors, and the vehicle can be started if the key fob is placed in the backup slot, located in the center console storage compartment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024 Bronco vehicles equipped with the 2.3L engine may exhibit a red brake warning lamp and brake system warning message in the instrument panel cluster (IPC) with a diagnostic trouble code (DTC) P050F in the anti-lock brake system (ABS) modul
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2024 F150/Edge, 2018 MKX, 2019-2023 Nautilus, 2020-2025 Explorer/Aviator, 2021-2024 Bronco, and 2024 Ranger vehicles equipped with a 2.7L EcoBoost or a 3.0L EcoBoost engine may exhibit an engine oil leak from the crankshaft rear seal with retaining plate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Bronco vehicles equipped with a factory soft top roof and built on or before 14-Jul-2024 may experience snow or sand accumulation on the vehicles’ interior during a strong storm with high winds. To correct this condition, follow the Service Procedure to retrofit the soft top assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021–2024 Bronco and 2024 Ranger vehicles may exhibit a loss of driver's door switch pack control along with any of the following symptoms: * inability to open or close the windows * driver's window switch not working or not working intermittently * cannot fold or unfold the side mirror * cannot adjust the side mirror in any direction * diagnostic trouble code (DTC) B1087:87 stored in the driver's door module (DDM) and/or the passenger door module (PDM) * DTC U2013:23 stored in the DDM and/or PDM
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the following vehicles may exhibit one passive key that is unable to start the vehicle or activate the passive entry feature; however, all remote keyless entry (RKE) physical button functionality works correctly and the second passive key will have full/correct functionality (including being able to start the vehicle):
NHTSA source summary · Original PDF not reviewed by Recallfolio
Quality improvements include: -Robustness action to enhance the Connectivity, Networking and Cellular Data Services and power management. -Ensuring reliable functionality of Stolen Vehicle Services.
Campaign / software reference: 24-OTA SU 10.1.1 Bronco
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2024 Explorer/Aviator/Corsair, 2021-2024 F-150/Bronco, 2023-2024 F-Super Duty, and 2024-2025 Nautilus vehicles may experience the overhead console sunglass bin cannot be locked in a closed position.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Bronco may exhibit the upper rail front trim panel with an excessive gap. This may be due to the misalignment of the upper rail front trim panel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Bronco vehicles may exhibit a rattle from the front windows with the windows placed in the partially down position and driving over rough roads and/or bumps.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Quality Improvements include: - Addresses potential vehicle no start after OTA update. - Improved Phone as A Key functionality post Enhanced Central Gateway module (ECG) reset. - Minor quality fixes in Enhanced Central Gateway module (ECG) Software, not affecting vehicle operation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024 Bronco vehicles built on and before 23-Jun-2024 may exhibit a no crank/no start, discharged battery due to a parasitic battery drain condition. This may be due to the body control module C (BCMC). Perform battery drain test, refer to Workshop Manual (WSM) Section 414-01 Battery, Mounting and Cables - General Procedures - Battery Drain Check. If a battery drain of more than 1 Amp is identified, inspect fuse 8 in the BCMC for available voltage with the vehicle off and resting. If voltage is found, verify the draw is eliminated by removing fuse 8. If removing the fuse eliminates the draw, replace the BCMC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2024 F-150, 2021-2024 Bronco, and 2024 Ranger vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a stuck internal component of the variable cam timing (VCT) unit.