2021 Ford BRONCO Manufacturer communications & TSBs.Page 3
Original record summaries, dates and identifiers for this model-year. Records 201–300 of 316, ordered newest first. Dated records on this page: Aug 25, 2021–Nov 10, 2022.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Nov 10, 2022Service Bulletin/Repair Instructions
2122OT22PU1010SQ
NHTSA communication ID: 10227496
NHTSA source summary · Original PDF not reviewed by Recallfolio
Priority Update 22-PU1010-SFT-QL for 2021-2022 Model Year Bronco vehicles is now available. Quality Improvements Include: Improvements to upshift hesitation under certain tip in scenarios, improvements to shift quality, update to prevent misfire codes, updates to the Universal Exhaust Gas Oxygen sensor GHG Parameter identification reporting and Catalyst Monitor Sensor.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Priority Update 22-PU1007-DOR-UP for 2021-2022 Model Year Bronco vehicles is now available. Quality Improvements Include: improvement to short window drop, improvement to window bounceback.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles may experience multiple warning indicators/messages displayed in the instrument panel cluster including but is not limited to Pre-Collision Assist Not Available, Hill Start Assist Not Available and/or Front Camera Malfunction. The vehicle may also have multiple communication fault diagnostic trouble codes (DTC) setting in and/or related to the high speed control area network 2 (HS-CAN2) modules. This may be due to a loose and/or improperly seated connector C210. If the vehicle exhibits the above conditions, access and inspect connector C210 for proper attachment and/or damage and repair as necessary. If this fault persists, refer to Workshop Manual, Section 418-00A and continue with normal diagnostics. For claiming, use causal part 14290 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2150 and SSM 50970 to update the Service Procedure. For some 2021 Mustang Mach-E, F-150, Edge, Nautilus and Bronco vehicles technicians may experience the inability to update the accessory protocol interface module (APIM), telematics control unit (TCU) or gateway module (GWM) using the Ford Diagnosis and Repair System (FDRS) and Universal Serial Bus (USB) drive. The PTS OTA Dashboard on vehicles with this condition may also display multiple APIM and/or TCU updates have failed, and/or a no OTA history message. In addition, on vehicles with this condition, the customer may have reported experiencing a Ford Power-Up software update failure message via the vehicle display and/or FordPass/LincolnWay. This may be due to an internal software error. To correct this condition, follow the Service Procedure to update and/or recover the APIM/TCU. Note: Only 10% of vehicles may require this procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles may exhibit a condition of intermittent headlamp operation while the vehicle is OFF and have diagnostic trouble code (DTC) B1533 stored in the body control module (BCM). This may be due to the internal logic within the headlamp switch. To correct this condition, replace the headlamp switch (service base PN: 11654). Refer Workshop Manual, Section 417-01.
Source components: ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with a soft top roof may experience a broken window buckle on the rear quarter or rear window assemblies. It is no longer required to replace the window assembly to repair this condition. Order the following buckle parts as needed: male side of the buckle (M2DZ-00817-C), which is located on the soft top window assemblies and the female side of the buckle (M2DZ-00817-A), which is located on the soft top cover. To install the male buckle, cut and remove the old plastic clip leaving the fabric loop (on the window assembly) fully intact. The service replacement male buckle includes an open slot that is used to slide the fabric loop through for installation. Sewing is not required for installation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles may exhibit water leaks located at the A-pillars, overhead console/upfitter switches and/or sun visors. To correct the condition, follow the Service Procedure to diagnose and repair the water leak.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with a soft top may exhibit exterior wear on the sides of the top above the B-pillar. This may be due to contact and rubbing between the soft top frame and fabric. To correct the condition, follow the Service Procedure to replace both right and left deflectors attached to the soft top frame and soft top cover.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021 Model Year Bronco Vehicles Front Driveshaft Replacement. In the affected vehicles, the front driveshaft constant-velocity (CV) joint boot material is not robust for this application and may fail under normal vehicle usage. A failed CV joint boot may result in a loss of grease and the accumulation of debris in the CV joint, leading to noise and/or vibration while driving.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Bronco vehicles built on 01-Feb-2022 and through 10-Mar-2022 may exhibit rusted fasteners on the front fender trail sights (base part number 9920038). This may be due to a lack of protective e-coating applied to the bolts during the manufacturing process. Replacement of the exterior bodyside grab handle assembly will no longer be required. Trail sight fasteners are now available on their own as SPN: M2DZ-18D654-A. This kit comes with two bolts and two nuts, enough to replace all fasteners on one trail sight assembly. These fasteners work on both the left and right trail sights.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update 3 Part 2 for 2021-2022 Model Year Bronco vehicles is now available. Quality Improvements Include: Functionality of rear view camera is improved.
Source components: BACK OVER PREVENTION · BACK OVER PREVENTION: SENSING SYSTEM: CAMERA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2210 to update the expected release date of the revised ABS module software. Customers who neutral (4-wheel flat) tow 2021-2022 Broncos equipped with an electronic brake booster (EBB) may report an inconsistent brake assist when a supplemental braking system has been installed. This may result from supplemental brake system set-up that does not account for the Broncos EBB system entering sleep mode (via the ABS module) after a pre-determined period of time following vehicle shut-down. This functionality is necessary to prevent battery drain. Enhanced software is under development to address this condition when the vehicle enters Neutral Tow mode. The new software is expected to be available in December 2022. Monitor OASIS for updates. Until the software becomes available, customers who meet this criteria may perform the procedures below to address this condition when neutral (4-wheel flat) towing their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021 Model Year Bronco Vehicles Equipped with a Hard Top Roof Panel Delamination Program Terms - Updated to extend the program 1 additional year providing the vehicle is still within base warranty mileage limits. Owner Notifications - Revised owner letters
Source components: STRUCTURE:BODY:ROOF AND PILLARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Harvest/Inspection Program Certain 2021 Model Year 5 Door Bronco Vehicles Side Impact Sensor Retaining Stud and Nut Inspection This program is a proactive investigation by Ford Motor Company to inspect for the correct installation of a side impact crash sensor. Specifically, Ford is investigating whether the right hand and/or left hand side impact sensor could be missing the retaining stud and nut that secure the sensor to the b-pillar of the vehicle. Ford is voluntarily conducting this program because it received one report that a side impact sensor was not installed correctly, and it is inspecting other vehicles that were built around the same time. It is very important that the information and pictures from these inspections be provided to Ford for this study
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit an illuminated anti-lock brake system (ABS) indicator and stability-traction control indicator, and diagnostic trouble code (DTC) C1013:09 stored in the ABS module. This may be due to ABS module software. To correct the condition, follow the Service Procedure to update the ABS module software.
Source components: ELECTRONIC STABILITY CONTROL (ESC) · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit multiple error messages displayed in the IPC followed by automatic engagement of the parking brake immediately after starting the vehicle with the doors removed or after sitting in the vehicle for an extended period of time with the vehicle off. This may be due to the software within the anti-lock brake (ABS) module. To correct the condition, follow the Service Procedure to reprogram the ABS module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update 3 Part 1 for 2021-2022 Model Year Bronco vehicles is now available. Quality Improvements Include: Fix for low power mode rearview camera distortion when the vehicle is shut off and restarted quickly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with a stabilizer bar disconnect system may exhibit an illuminated red and/or amber stabilizer bar disconnect indicator and diagnostic trouble code (DTC) C103A:74 stored in the chassis control module (CHCM). This may be due to the software in the CHCM. To correct the condition, follow the Service Procedure to reprogram the CHCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The electronic parts catalog for the 2021-2022 Bronco equipped with a 2.7L GTDI engine had the incorrect engine oil dipstick assigned. This problem only existed for a few months and has since been corrected. The incorrect dipstick that showed in the catalog was SPN: MB3Z-6750-B/F (EPN: MB3E-6750-BB/BC). The 'MB3Z' dipstick (EPN: 'MB3E') is ONLY designed for use on the 2022 Bronco Raptor which is equipped with a 3.0L GTDI engine. The correct engine oil dipstick for the 2021-2022 Bronco 2.7L GTDI engine is SPN: FT4Z-6750-B/C (EPN: FT4E-6750-BF/BG).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2022 Ford/Lincoln vehicles equipped with a wireless charging pad may exhibit one of the following if the customer is using a Magsafe iPhone (iPhone 12 or 13): slow charging, inoperative, notification that the phone has been mispositioned on the charging pad and/or the phone charging icon in the center screen display is not showing. This may be due to a compatibility issue between the customer's phone and the wireless accessory charging module (WACM) that may make it difficult for Ford and Lincoln vehicles to wirelessly charge these specific phones. The phone can still be charged using the USB cable if the vehicle experiences the above symptoms. If the customer is using a Magsafe iPhone such as an iPhone 12 or 13, verify the wireless charging pad works with a Qi certified phone prior to any part replacements.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2022 Ford/Lincoln customers may experience a notification in the FordPassÃÂÃÂÃÂî/LincolnWayÃÂÃÂÃÂî app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with base exterior mirrors (does not have integrated puddle lamps and/or turn signal lamps) may have a whistle noise that originates from the left exterior mirror. This may be due to the design of the exterior mirror cover. To correct this condition, follow the Service Procedure to replace both the left and right exterior mirror covers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with a factory soft top roof may experience excessive wind noise while driving, loose soft top cover, and/or difficulty latching. This may be due incorrect soft top assembly installation, latch striker positioning and/or a failed soft top component. To correct the conditions, follow the Service Procedure to inspect the vehicle and adjust the soft top components as necessary.
Source components: STRUCTURE:BODY:ROOF AND PILLARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with a hard top roof may exhibit symptoms from the front roof panels that sit at an uneven height which may result in a poor appearance, excessive wind noise, water leaks and/or difficulty latching. This may be due to incorrect vertical adjustment of the front roof panel latch strikers. To correct this condition, follow the Service Procedure to adjust the front panel latch strikers.
Source components: STRUCTURE:BODY:ROOF AND PILLARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with an EBB may exhibit multiple error messages displayed in the IPC followed by automatic engagement of the parking brake immediately after starting the vehicle with the doors removed or after sitting in the vehicle for an extended period of time with the vehicle off. The issue will resolve itself once the brake pedal is no longer depressed or the parking brake is manually disengaged. This may be due to the software within the anti-lock brake (ABS) module. This issue can be avoided by placing the vehicle in accessory mode for a few seconds before starting the engine. Engineering is working on improved software to correct this condition that will be available in November 2022. No repairs should be made in attempt to correct this condition. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles built on or before 14-Mar-2022 and equipped with a 2.7L engine may exhibit the inability to disable the traction control system using the traction control on/off switch located on the instrument panel. This may be due to the software within the anti-lock brake system (ABS) module. To correct the condition, follow the Service Procedure and update the ABS software.
Source components: BACK OVER PREVENTION:SOFTWARE · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021 Model Year Mach-E, F-150, Bronco, Edge, Nautilus vehicles Electronic Control Module Recovery: In some of the affected vehicles, an internal error in the Accessory Protocol Interface Module (APIM) or Telematics Control Unit (TCU) module software will prevent the receipt of software updates or enhancements for these modules Ford Power-Up or Lincoln Way. The module will operate as intended otherwise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles may exhibit a Cross Traffic System/Blind Spot System Fault in instrument panel cluster (IPC). If these symptoms are encountered, inspect the wiring under the rear bumper for chaffing of the 13A409 harness close to connector C4369. If this is determined to be the cause of the issue, refer to Wiring Diagram Cell 005 for wiring repair. If no wiring issues are found, continue with normal diagnostics in Workshop Manual (WSM), Section 419-04.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles may exhibit a condition of intermittent headlamp operation while the vehicle is OFF and have diagnostic trouble code (DTC) B1533 stored in the body control module (BCM). This may be due to the internal logic within the headlamp switch. Switch and/or module replacement will not resolve this condition. Headlamp operation is not affected while the vehicle is ON. A new headlamp switch is currently under development to correct this condition. Let the customer know they can continue to drive the vehicle and schedule a follow-up appointment in October 2022, when parts are expected to become available. Follow up with the customer to confirm the appointment once OASIS is updated with the repair information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2021-2022 various Ford and Lincoln vehicles may exhibit an erroneous diagnostic trouble code (DTC) U1A01:93 stored in the telematics control unit (TCU). This may be due to various software parameters within the TCU. If this DTC is identified during normal diagnostics, but the vehicle does not exhibit any customer concerns around the TCU operation, clear this DTC and no further repairs are recommended. If the DTC returns after being cleared or if the vehicle exhibits connectivity concerns with the TCU, continue with normal Workshop Manual (WSM) diagnostics. If set erroneously, this DTC does not cause any observable concerns or warning messages and does not affect vehicle performance or durability. Ford is developing a software update which will be delivered to the vehicle via an over-the-air (OTA) TCU update in July 2022 to prevent this DTC from setting erroneously.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with base exterior mirrors (does not have integrated puddle lamps and/or turn signal lamps) may have a whistle noise that originates from the left exterior mirror. This may be due to the design of the exterior mirror cover. To correct this condition, follow the Service Procedure to replace both the left and right exterior mirror covers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update 2 (SU2) Phase 1-3 Respin for 2021 Model Year Bronco vehicles is now available. Involves: Fix for availability of subscription services.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles built on or before 17-May-2022 equipped with 5 doors and a hard top roof configuration, may exhibit poor Sirius XMî satellite radio reception and/or satellite radio signal loss in areas with tall structures, rural areas with dense foliage or other similar obstructions. This may be due to the antenna positioning. To correct the condition, follow the Service Procedure to relocate the antenna.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customers who neutral (4-wheel flat) tow 2021-2022 Broncos equipped with an electronic brake booster (EBB) may report an inconsistent brake assist when a supplemental braking system has been installed. This may result from supplemental brake system set-up that does not account for the Bronco's EBB system entering sleep mode (via the ABS module) after a pre-determined period of time following vehicle shut-down. This functionality is necessary to prevent battery drain. Enhanced software is under development to address this condition when the vehicle enters Neutral Tow mode. The new software is expected to be available in September 2022. Monitor OASIS for updates. Until the software becomes available, customers who meet this criteria may perform the procedures below to address this condition when neutral (4-wheel flat) towing their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator and 2021-2022 Bronco vehicles may exhibit an illuminated airbag warning indicator with diagnostic trouble code (DTC) B1404:13 and/or B1407:13. This may be due to contamination and relative movement in the connection between the wiring harness and the side airbag. To correct the condition, follow the Service Procedure to replace the affected connector with a service pigtail and the affected side airbag.
Source components: AIR BAGS:SRS MALFUNCTION WARNING LAMP/LIGHT · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The 2021-2022 Bronco Workshop Manual, Section 501-18B Hard Top, has been updated. Updates include hard top rear cap flushness and parallelism specifications and an enhanced diagnostics and testing section to assist with resolving concerns of hard top roof alignment, looseness, water leaks, and noise vibration and harshness (NVH). Submit photos of hard top roof concerns that require part replacement for any reason using web-based PTS or Mobile PTS Report a Vehicle Concern function. This applies to Broncos built on/after 12-Aug-2021 equipped with hard top roof or vehicles repaired under Customer Satisfaction Program 21B49. For claiming, use labor operation SUBPHOTO for reimbursement. The hard top roof is enhanced to meet standards expected by customers. To assist with long-term supplier quality, Ford is seeking immediate dealer feedback on customer concerns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with a soft top roof may experience paint scratches on the sports tube paint due to contact with the soft top roof frame during the open and close operation. This may be due to a lack of protective measures installed on the soft top roof frame. To correct this condition, follow the Service Procedure to install protective plates and hook and loop fasteners to sections of the soft top roof frame.
Source components: STRUCTURE:BODY:ROOF AND PILLARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 and 2022 Ford and Lincoln vehicles may experience a tire sidewall wavy/indentation appearance in the radial direction on one or both sidewalls. Sidewall wavy/indentation appearance is a common cosmetic characteristic of radial tire construction and will not affect the performance of the tire.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021 Model Year Mach-E, F-150, Bronco, Edge, Nautilus vehicles - Electronic Control Module Recovery: In some of the affected vehicles, an internal error in the Accessory Protocol Interface Module (APIM) or Telematics Control Unit (TCM) module software will prevent the receipt of software updates or enhancements for these modules from Ford Power-Up or Lincoln Way. The module will operate as intended otherwise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator and diagnostic trouble codes (DTCs) C05F9 and/or C05D9 stored in the all-wheel drive (AWD) module and inoperative AWD system. These DTCs maybe setting due to a low battery state of charge. To correct the condition, follow the Service Procedure to verify the battery condition and restore the AWD module logic.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles may exhibit a squeak and/or rattle that originates from the roof while driving over rough surfaces. This may be due to poor roof installation, noisy roof seals or roof latches/locator pins wearing prematurely. Follow the service procedure to correct the source of the noise.
Source components: EQUIPMENT · STRUCTURE:BODY:ROOF AND PILLARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 F-150/Bronco and 2022 Expedition/Navigator vehicles may exhibit an illuminated anti-lock brake system (ABS) indicator and stability-traction control indicator when ambient temperatures are below freezing, and diagnostic trouble code (DTC) C1013:09 stored in the ABS module. This may be due to ABS module software parameters and the effects of low ambient temperature on brake fluid viscosity. This condition does not affect brake system hydraulic functionality. Clear the DTC to restore ABS and stability-traction control functionality and inform customers that Ford is developing a software update which will be delivered to the vehicle via an over-the-air (OTA) ABS update in November 2022 to prevent this condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles may exhibit a window rattle when driving over bumps with the windows placed in the partially down position. This may be due to incorrect window glass adjustment from the factory. To correct this condition, perform the Front/Rear Door Window Glass Adjustment procedure located in the Workshop Manual, Section 501-11 > Front doors > Steps 18-26, Rear Doors > Steps 21-25. It is not necessary to remove the door panel to perform this adjustment. During adjustment, set the window regulator nuts to their most outboard position (this will move the top of the window inboard), then reevaluate the noise. Be sure to place the window in the fully down position during adjustment.
Source components: VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2117 to update the Issue, Action, Service Procedure. For some 2021 Mustang Mach-E, F-150, Edge, Nautilus and Bronco vehicles technicians may experience the inability to update the accessory protocol interface module (APIM) or telematics control unit (TCU) using the Ford Diagnosis and Repair System (FDRS) and Universal Serial Bus (USB) drive. The PTS OTA Dashboard on vehicles with this condition may also display multiple APIM and/or TCU updates have failed, and/or a no OTA history message. In addition, on vehicles with this condition, the customer may have reported experiencing a Ford Power-Up software update failure message via the vehicle display and/or FordPass/LincolnWay. This may be due to an internal software error. To correct this condition, follow the Service Procedure to update and/or recover the APIM/TCU. Note: Only 10% of vehicles may require this procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2021-2022 Bronco vehicles are equipped with a smart windshield wiper motor, which has the capability of sensing load of the wiper blades coming across the windshield glass. As a result of this operational characteristic/design, the operation may not be what is expected in certain conditions. The vehicle is programmed with protection features to prevent damage to the wiper motor in case of overheating, operation with dry windshields, or obstructions to the wiper blade (snow, ice, etc.). In such conditions, the wiper motor will temporarily reduce its speed and/or reduce area of cleaning until the condition is no longer present.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL · VISIBILITY:WINDSHIELD WIPER/WASHER:MOTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Ranger/Bronco vehicles equipped with a 2.3L EcoBoost engine built on or after 14-Dec-2021 and 2022 Explorer vehicles equipped with a 2.3L EcoBoost engine and built on or after 14-Dec-2021, may exhibit a lack of power with an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P25B4 stored in the powertrain control module (PCM). To correct the condition, clear the DTC and road test the vehicle under load until the vehicle reaches operating temperature. If the DTC repeats, the turbocharger will need to be replaced. For claiming use causal part 6K682 and applicable labor times found in Section 09 of the Service Labor Time Standards (SLTS) Manual. If the DTC does not repeat, release the vehicle to the customer.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In various 2017-2022 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating "Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with 5 doors and a hard top roof may experience a squeak and/or chirp noise from the rear of the vehicle while driving over bumps with the roof installed. This may be due to an insufficient gap between the hard top and the body rear quarter panel. To correct the condition, follow the Service Procedure to adjust this gap to the correct specifications.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2021 Ranger vehicles built on or before 09-Aug-2021 and 2021 Bronco vehicles equipped with a 2.3L engine may experience reduced engine power in freezing temperatures with an illuminated malfunction indication lamp (MIL) and/or powertrain malfunction indicator (wrench) lamp with diagnostic trouble codes (DTC) P2111, P2112, and/or P2119. This may be due to water or ice buildup in the intake manifold behind the throttle body. If suspected, remove the throttle body and inspect for water or ice in the base of the intake manifold. If water or ice is found, replace the intake manifold with part number KB3Z-9424-B and crankcase vent oil separator hose, part number LB5Z-6A664-D. Refer to Workshop Manual Sections 303-01 and 303-08. For claiming, use causal part number 9424 and applicable labor times from Section 09 of the Service Labor Times Standard (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with parking aid sensors may exhibit a park aid system that does not remain deactivated after the vehicle has been off for more than 5 minutes. The vehicle may exhibit false alerts from the parking aid warning system which may cause it to activate while driving or towing or due to the presence of a winch. This may be due to the software within the instrument panel cluster (IPC). To correct the condition, follow the Service Procedure and update the IPC software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles may experience a water leak that originates from the left and/or right A-pillars and/or the windshield header. This may be due to excessive gaps in the body seams from the factory. To correct the condition, follow the Service Procedure to reseal the affected body gaps and replace the front header seal.
Source components: STRUCTURE:FRAME AND MEMBERS · VISIBILITY:WINDSHIELD.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with a hard top may exhibit a loose and/or sagging headliner. This may be due to the factory installation process. To correct the condition, follow the Service Procedure to re-adhere the headliner.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles may exhibit a squeak and/or rattle that originates from the roof while driving over rough surfaces. This may be due to poor roof installation, noisy roof seals or roof latches/locator pins wearing prematurely. Follow the service procedure to correct the source of the noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update 2 (SU2) Phases 1, 2 and 9 for 2021 Model Year Bronco vehicles is now available. Involves: Fix for availability of subscription services, UEGO fix, addresses 2.3L engine missfires, addresses hesitation durring upshifts, improved shift quality, and prevents "no key detected" message when the door modules are sensing low voltage.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with a soft top roof may exhibit loose exterior fabric on the rear window assembly. This may be due to broken D-pillar clips on the rear window. To correct the condition, follow the Service Procedure to replace the D-pillar clips with rivets.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco/F-150/Explorer/Aviator/Police Interceptor Utility and 2022 Transit vehicles may exhibit harsh/delayed engagement and/or harsh/delayed shift concerns. These may be addressed with the powertrain control module (PCM)/transmission control module (TCM) Transmission Accelerated Main Control Break In Routine and/or a main control overhaul. Refer to Workshop Manual (WSM), Section 307-01, DTC Chart if DTCs are present and/or Diagnosis By Symptom to identify the clutch(s) to be cycled. Cycling the shift solenoids and clutch control valves to remove contamination must be performed along with an adaptive drive cycle before attempting repair. For claiming, use causal part 7A100 and applicable labor operations in Section 7 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2021-2022 Bronco vehicles built on/after 12-Aug-2021 equipped with hard top roof or vehicles repaired under Customer Satisfaction Program 21B49. Submit photos of hard top roof concerns that require part replacement for any reason using web-based PTS or Mobile PTS Report a Vehicle Concern function. For payment, use labor operation SUBPHOTO for reimbursement. The hard top roof is enhanced to meet standards expected by customers. To ensure long-term supplier quality is maintained, Ford is seeking immediate dealer feedback on customer concerns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with parking aid sensors may exhibit a park aid system that does not remain deactivated after a key cycle. The vehicle may exhibit false alerts from the parking aid warning system which cause it to activate while driving or towing or due to the presence of a winch. This may be due to the software within the instrument panel cluster (IPC). To correct the condition, follow the Service Procedure and update the IPC software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles equipped with rubberized flooring may encounter a white chalky/dull appearance due to excessive wax raising from the surface. To correct this condition, follow the Service Procedure to clean the rubberized floor.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles may exhibit a side door window that gets hung up on the upper door weatherstrip when opening the door causing resistance to opening. This may be due to an incorrect alignment of the side door and/or window. To correct this condition, ensure no damage exists to the door, latch or related components and make necessary repairs before continuing. If concern persists, perform the Up/Down, Fore/Aft Adjustment (steps 1-15), refer to Workshop Manual (WSM), Section 501-11, Front/Rear Door Window Glass Adjustment Procedure. If the concern has not been resolved, perform Pinpoint Test K located in Section 501-11 of the WSM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2021-2022 various Ford and Lincoln vehicles may exhibit an erroneous diagnostic trouble code (DTC) U1A01:93 stored in the telematics control unit (TCU). This may be due to various software parameters within the TCU. If this DTC is identified during normal diagnostics, but the vehicle does not exhibit any customer concerns around the TCU operation, clear this DTC and no further repairs are recommended. If the DTC returns after being cleared or if the vehicle exhibits connectivity concerns with the TCU, continue with normal Workshop Manual (WSM) diagnostics. If set erroneously, this DTC does not cause any observable concerns or warning messages and does not affect vehicle performance or durability. Ford is developing a software update which will be delivered to the vehicle via an over-the-air (OTA) TCU update in July 2022 to prevent this DTC from setting erroneously.
Source components: ELECTRICAL SYSTEM:SOFTWARE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco vehicles may exhibit a creak/pop type noise when any of the side doors are opened and closed. This may be due to incorrect door installation, alignment and/or incorrect tightening of the two bolts which hold the door to the vehicle body. To correct this condition, inspect for and address any damage to the door and/or latch components, then remove and reinstall the suspect door following the instructions located in the Digital Owners Manual, Removable Vehicle Components > Removable Doors > Removing and Installing the Doors. In this section youll also find a detailed tutorial video of the process. If the noise persists, perform the Front/Rear Door Alignment procedure located in the Workshop Manual (WSM), Section 501-03 Body Closures.
Source components: LATCHES/LOCKS/LINKAGES:DOORS:LOCK · STRUCTURE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2021-2022 Bronco vehicles equipped with a factory soft top roof may require replacement of the soft top canopy material. Replacement rivets are now available (service part number W790580-S900). Each package contains 4 rivets.
Source components: STRUCTURE:BODY:ROOF AND PILLARS · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Broncos may exhibit a whistle noise coming from the front center of the vehicle and/or the climate control housing. This may be due to the sealing on the climate control case. To correct the condition, follow the Service Procedure to apply butyl tape to cover small holes in the fresh air inlet door.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Broncos may exhibit a whistle noise coming from the front center of the vehicle and/or the climate control housing. This may be due to the sealing on the climate control case. To correct the condition, follow the Service Procedure to apply butyl tape to cover small holes in the fresh air inlet door.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 F-150 and Bronco vehicles built with SYNC 4 require a connected phone with Android Auto or Apple CarPlay active to enable voice interactions and use of the steering wheel Voice Control button. This is due to the affected vehicles not having built in voice interactions capability. Vehicles with built in voice interactions capability can be identified as also being equipped with the built in Connected Navigation feature which includes a navigation tab on the touchscreen. Diagnostics should only be performed for voice interactions on vehicles equipped with built in voice interaction capability or with Android Auto or Apple CarPlay active.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco vehicles equipped with exterior zone lighting may experience the hazard lamps flashing one time intermittently when the hazard lamps are turned off. This condition is due to the body control module (BCM) software. This condition occurs when zone lighting is activated then deactivated while the engine is OFF, or during an engine auto-start-stop event. To correct this condition, follow the Service Procedure to reprogram the BCM.
Source components: ELECTRICAL SYSTEM:BODY CONTROL MODULE:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco Badlands and First Edition vehicles built on or before 19-Nov-2021 with a stabilizer bar disconnect system may exhibit an illuminated red and/or amber stabilizer bar disconnect indicator and diagnostic trouble codes (DTC) C103A:74, C1B03:67 and/or C1B07:67 stored in the chassis control module(CHCM). This may be due to the software in the CHCM. To correct the condition, follow the Service Procedure to reprogram the CHCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco/F-150/Explorer/Aviator/Police Interceptor Utility vehicles, non-hybrid, may exhibit harsh/delayed engagement and/or harsh/delayed shift concerns. These may be addressed with the powertrain control module (PCM)/transmission control module (TCM) Transmission Accelerated Main Control Break In Routine. Refer to Workshop Manual (WSM), Section 307-01, DTC Chart and/or Diagnosis By Symptom to identify the clutch(s) to be cycled. Cycling the shift solenoids and clutch control valves to remove contamination must be performed along with an adaptive drive cycle before attempting repair. This routine's usage has been expanded for various symptoms across the life of the vehicle. For claiming, use causal part 7A100 and applicable labor operations in Section 7 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco vehicles equipped with the 2.3L engine may exhibit a red brake warning lamp and/or brake system warning message in the instrument panel cluster (IPC) with a diagnostic trouble code (DTC) P050F in the anti-lock brake system (ABS) module and a firm brake pedal. This may be due to contamination in a brake booster vacuum line. To correct this condition, replace the vehicle's vacuum hose (MB3Z-2420-A). Refer to Workshop Manual (WSM), Section 206-09 for installation instructions. For claiming, use casual part 2420.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 EcoSport, Expedition, Navigator; 2019-2021 Ranger; 2020-2021 Escape, Corsair, Explorer, Transit; 2021 Bronco, Bronco Sport, Edge, Nautilus, F-150, Mustang; 2019-2022 Transit Connect; 2020-2022 Aviator, F-Super Duty; and 2022 Maverick vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0496, P0456, P0455, P04F0, and/or P0451. Ford has tested returned EVAP canister purge valves and found them to be fully functional. Prior to replacing the canister purge valve or other EVAP components, perform the following tests using the Ford Diagnosis and Repair System (FDRS) Scan Tool: Full System EVAP Leak Test - FDRS Location: TOOLBOX > PCM > PCM - Evap Emissions System Test and the EVAP Purge Valve Leak Test - FDRS Location: TOOLBOX > PCM > Evap Emission System Toolbox > CPV Check.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Ranger and Bronco vehicles built on 15-Jun-2021 and through 15-Aug-2021 may exhibit an illuminated anti-lock brake system (ABS) warning indicator lamp with diagnostic trouble codes (DTC) C003A, C0036, C0037, and/or C0039 stored in the ABS control module. This may be due to damage or movement of the ABS tone ring on the rear axle. Remove the ABS sensor and inspect the rear ABS tone ring for damage or movement from its original position. If movement or damage has occurred, refer to Workshop Manual (WSM), Section 205-02 to complete the service procedure for axle shaft replacement. If no movement has occurred, refer to WSM, Section 206-09 for normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco vehicles may experience a water leak that originates from the left and/or right A-pillars and/or the windshield header. This may be due to excessive gaps in the body seams from the factory. To correct the condition, follow the Service Procedure to reseal the affected body gaps and replace the front header seal.
Source components: STRUCTURE:BODY:ROOF AND PILLARS · VISIBILITY:WINDSHIELD.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco, Edge/Nautilus customers may be unable to authorize the FordPass/LincolnWay app and the Enable Connected Services prompt is not showing in the SYNC screen with no diagnostic trouble codes (DTC) present in the telematics control unit (TCU) or the gateway module A (GWM). Before any repair attempts, try to authorize the vehicle via FordPass/LincolnWay app in order to verify the concern is still present. If the concern is present, make sure the GWM is at the latest software level. Start a new FDRS session and make sure the TCU is at the latest software level. If no software updates are available, remove the TCU and GWM fuses to reset the modules. Make sure the customer is able to authorize the vehicle from FordPass/LincolnWay to confirm the repair. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 F-150/Mustang Mach-E/Bronco/Edge/Nautilus customers may experience an inoperative FordPass/LincolnWay app, features in FordPass/LincolnWay are not functioning and/or the customer cannot pair the FordPass/LincolnWay mobile app to the vehicle. If the telematics control unit (TCU) on the vehicle does not exhibit any diagnostic trouble codes (DTC), but the customer is running into these app concerns, this may be due to poor cell signal getting to the TCU. The TCU - Provisioning Application on the Ford Diagnosis and Repair System (FDRS) scan tool will provide cell signal strength information that can help to diagnose the source of the poor cell signal. If poor cell signal is found, refer to WSM 415-00 to help identify an antenna concern. Be sure the vehicle is an open environment.
Source components: COMMUNICATION:MANUFACTURER TELEMATICS · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco vehicles equipped with a 2.7L EcoBoost engine and built on or before 01-Sep-2021 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P2096 and/or P2098 stored in the powertrain control module (PCM). This may be due to various software parameters within the PCM and/or a catalyst monitor sensor. To correct the condition, follow the Service Procedure to reprogram the PCM.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021 Model Year Bronco Vehicles Equipped with a Hard Top Roof Roof Panel Delamination REASON FOR THIS SUPPLEMENT Technical Information - Dealership: Updated with revised directions regarding hard top panels and rear cap assembly disablement and photo submission requirement. As a result, the Labor Allowances have also been updated.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:BODY:ROOF AND PILLARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco vehicles built on or before 14-Sep-2021 may experience a loss of power when driving with various illuminated warning indicators displayed in the instrument panel cluster (IPC). This may be due to an improper seating of the wiring harness push pins to the driveshaft loop which can cause an interference condition between the rear driveshaft and the 14405 harness near the C2370/C350 connector. If suspected, inspect the harness and connector for damage and repair as necessary. Once inspected and/or repaired fully, seat the harness push pins to the driveshaft loop.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2021 Ranger vehicles built on or before 09-Aug-2021 and 2021 Bronco vehicles may experience a loss of power when driving in freezing temperatures with an illuminated malfunction indication lamp (MIL) and/or powertrain malfunction indicator (wrench) lamp with diagnostic trouble codes (DTC) P2111, P2112, and/or P2119. This may be due to water or ice buildup in the intake manifold behind the throttle body. If suspected, remove the throttle body and inspect for the presence of water or ice in the base of the intake manifold. If water or ice is found, replace the intake manifold with part number KB3Z-9424-B and crankcase vent oil separator hose, part number LB5Z-6A664-D. Refer to Workshop Manual (WSM) Sections 303-01 and 303-08. For claiming, use causal part number 9424 and applicable labor times from Section 09 of the Service Labor Times Standard (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco vehicles built on or before 23-Aug-2021 may experience a charging system fault message displayed in the instrument panel cluster (IPC) and diagnostic trouble codes (DTC) U012D, U0284 and/or U0285 stored in the powertrain control module (PCM). This may be due to water intrusion in the active grille shutter connector. To correct this condition, follow the Service Procedure to inspect for water intrusion in the active grille shutter harness connector and repair as needed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Broncos built on or before 24-Aug-2021 may exhibit a whistle noise coming from the front center of the vehicle and/or the climate control housing. This may be due to the sealing on the climate control case. To correct the condition, follow the Service Procedure to apply butyl tape to cover small holes in the fresh air inlet door.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco, Edge and Nautilus customers may be unable to authorize the FordPass/LincolnWay app and the Enable Connected Services prompt is not showing in the SYNC screen with no diagnostic trouble codes (DTC) present in the telematics control unit (TCU) or the gateway module A (GWM). Before any repair attempts, try to authorize the vehicle via FordPass/LincolnWay app in order to verify the customer concern is still present. If the concern is present, make sure the GWM is at the latest software level, and then make sure the TCU is at the latest software level. If no software updates are available, remove the TCU and GWM fuses to reset the modules. Make sure the customer is able to authorize the vehicle from FordPass/LincolnWay to confirm the repair. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00.
Source components: COMMUNICATION:MANUFACTURER TELEMATICS · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Broncos equipped with the Base, Big Bend, Black Diamond and/or Badlands trim levels built on or before 23-Jun-2021 may exhibit a whistle type noise coming from the drivers side mirror area of the vehicle. This may be caused by an excessive gap between the exterior mirror cover and glass housings. If the source of the noise is coming from the drivers door mirror assembly an updated exterior mirror cover is available to correct this condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco vehicles equipped with the Big Bend or Outer Banks trim levels built on or before 06-Aug-2021 may exhibit a whistle noise originating from the front of the hood area when traveling at speeds above 30 mph (50 km/h). If the whistle noise can be eliminated by taping off the gap between the hood and grille opening, this condition may be due to the hood seal design. To correct this condition, replace the hood seal with the improved hood seal.
Source components: EQUIPMENT · STRUCTURE:BODY:HOOD · STRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco/F-150/Explorer/Aviator/Police Interceptor Utility vehicles, excluding hybrid, may exhibit harsh or delayed engagement/shift concerns. Most concerns may be addressed with the PCM/TCM Transmission Accelerated Main Control Break In Routine. Refer to Workshop Manual (WSM), Section 307-01, DTC Chart and/or Diagnosis By Symptom to identify the clutch(s) to be cycled. This routine cycles the shift solenoids and clutch control valves to remove contamination that may be sticking the valves and must be performed along with an adaptive drive cycle before attempting internal service. Although this routine was developed for low mileage vehicles, its usage is being expanded for various symptoms across the life of the vehicle.For claiming, use causal part 7A100 and applicable labor operations in Section 7 of the Service Labor Time Standards (SLTS) Manual.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CLUTCHES/BANDS:ACTUATORS/SOLENOIDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco vehicles equipped with front parking aid sensors and a Ford Performance and/or aftermarket winch may inhibit the front parking aid sensor warning system and cause it to activate. As a resolution, the front sensors must be turned off by performing the following from the touchscreen; 1. Press Features on the touchscreen. 2. Press Driver Assistance > Park Aid Sensors > Front On, Rear On. 3. Front Sensors (Always) Off > Park Aid Sensors > Front Sensors (Always). Note: trying to adjust the location of the sensor will not resolve this concern. If the front sensors do not stay off after each key cycle monitor OASIS for additional information and schedule a service appointment with the customer once the repair becomes available.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:ADAS:PARKING ASSIST:SENSORS · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco vehicles equipped with a soft top roof may experience paint scratches on the sports tube due to contact with the soft top roof frame during the open and close operation. This may be due to a lack of protective measures installed on the soft top roof frame. To correct the condition, follow the Service Procedure to apply protective hook and loop fasteners to sections of the soft top roof frame.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:BODY:ROOF AND PILLARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021 Model Year Bronco Vehicles Equipped with a Hard Top Roof Roof Panel Delamination; In all of the affected vehicles, the exposed or unsealed edges on the molded in color hard top roof may cause an unsatisfactory appearance when exposed to extreme water and humidity. This concern is strictly an appearance issue as the function of the roof is uncompromised.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco vehicles equipped with front and rear parking aid sensors may set diagnostic trouble codes (DTCs) for all 8 parking aid sensors and/or circuits. This may be due to the software within the parking aid module (PAM). To correct the condition, reprogram the PAM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 15K866 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. After PAM programing check for DTCs and correct as necessary.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco vehicles may experience multiple warning indicators / messages displayed in the instrument panel cluster (IPC) and/or multiple communication fault diagnostic trouble codes (DTC) setting in and/or related to the HS2-CAN modules. This may be due to a loose and/or improperly seated connector C210. If the vehicle exhibits the above conditions, access and inspect connector C210 for proper attachment and/or damage and repair as necessary. To access the connector, remove the right side lower cowl side panel (follow Workshop Manual, (WSM) Section 415-00 > Removal and Installation > A-Pillar Speaker, Steps 9-10) and the glove compartment (follow WSM Section 501-12 > Removal and Installation > Glove Compartment). If this fault persists, refer to WSM Section 418-00A and continue with normal diagnostics.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator and 2021 Bronco vehicles may exhibit an illuminated airbag warning indicator with diagnostic trouble code (DTC) B1404:13 and/or B1407:13. This may be due to contamination and relative movement in the connection between the wiring harness and the side airbag. To correct the condition, follow the Service Procedure steps to replace the affected connector with a service pigtail and the affected side airbag.
Source components: AIR BAGS:SENSOR:SIDE IMPACT · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco 5 door models equipped with a hard top roof configuration may exhibit poor Sirius XM satellite radio reception and or signal loss in rural areas with dense foliage, tall buildings, or other similar obstructions. No additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution to improve this condition that is expected to be available for service in January 2022. In addition, if the vehicle is equipped with the optional factory roof rails and crossbars this may further degrade the reception. Removing the roof rails and crossbars may improve reception performance. Monitor OASIS for additional information and schedule a service appointment with the customer once the repair becomes available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco vehicles equipped with a hard top may exhibit a loose and/or sagging headliner. This may be due to the factory installation process. To correct the condition, follow the Service Procedure to re-adhere the headliner.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
Source components: SERVICE BRAKES, ELECTRIC:SOFTWARE/PROGRAMMING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Bronco 5 door models equipped with a hard top roof configuration may exhibit poor Sirius XM satellite radio reception and or signal loss in rural areas with dense foliage, tall buildings, or other similar obstructions. No additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected to be available for service in January 2022. In addition, if the vehicle is equipped with the optional factory roof rails and crossbars this may further degrade the reception. Removing the roof rails and crossbars may improve reception performance. Monitor OASIS for additional information and schedule a service appointment with the customer once the repair becomes available.