Original record summaries, dates and identifiers for this model-year. Records 101–200 of 263, ordered newest first. Dated records on this page: Oct 3, 2015–Jun 14, 2017.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jun 14, 2017Service Bulletin/Repair Instructions
9003413
NHTSA communication ID: 10138856
NHTSA source summary · Original PDF not reviewed by Recallfolio
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
Source components: STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs set in the PCM memory: U1504 - Implausible Message Data Length Received From Steering Angle Sensor. P0128 - Thermostat Rationality. P0335 - Crankshaft Position Sensor Circuit. P0340 - Camshaft Position Sensor Circuit Bank 1 Sensor 1. U1424-00 - Implausible Engine Torque Signal Received. P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance.In addition to the DTCs above the following improvements have been made: Min spark changes to prevent catalytic converter overheating. Engine Startup Flare and Idle Surge. P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range. U0401 - Implausible Data Received From ECM/PCM - Signal Invalid.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs set in the PCM memory: U1504 - Implausible Message Data Length Received From Steering Angle Sensor. P0128 - Thermostat Rationality. P0335 - Crankshaft Position Sensor Circuit. P0340 - Camshaft Position Sensor Circuit Bank 1 Sensor 1. U1424-00 - Implausible Engine Torque Signal Received. P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance.In addition to the DTCs above the following improvements have been made: Min spark changes to prevent catalytic converter overheating. Engine Startup Flare and Idle Surge. Improved vehicle acceleration. P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range. U0401 - Implausible Data Received From ECM/PCM - Signal Invalid.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING · STEERING · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
NHTSA source summary · Original PDF not reviewed by Recallfolio
Replace Vehicle Emission Certification Information Label This bulletin involves replacing the Vehicle Emission Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Replace Vehicle Emission Certification Information Label This bulletin involves replacing the Vehicle Emission Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Compressor, A/C lines, A/C Condenser This issue pertains to PF, UF, and KL only.~ During service of the AC lines, Compressor or Condenser, do not stow any AC lines in proximity to any heat sources, or sharp edges.~ After the vehicle is reassembled, confirm that all AC lines are in correct design position and not in contact with any heat sources, or sharp edges.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Panasonic 8.4" CTP/FCTP Radio, Update Failure Issue 1: Hand Free Module inoperative, can't pair phone: - Do not replace the radio for phone issues. The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A for an exchange or 05064993A for a new part replacement. Prior to replacing parts, Please contact Leony Gonzalez at cell (248) 736-1267 or Reggie Phillips at cell (678) 330-0255. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair.~ Issue 3; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Reggie Phillips at cell (678) 330-0255. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio. ~ ~______________________________________~ Contact Us at CAGRIS@Chrysler.com for feedback related ONLY to this GPOP Tech Tip. DO NOT email regarding repair procedures unrelated to this Tech Tip or part order inquires. Please include the Part Number (s) and Tech Tip Part Description of the Tech Tip you are referencing for our tracking system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
NHTSA source summary · Original PDF not reviewed by Recallfolio
(X62) Hydraulic Clutch Master Cylinder / Reservoir Hose - 2013-2015 Dodge Dart and 2014-2015 Jeep Cherokee (Rev. A) To announce an extended warranty on the Hydraulic Clutch Master Cylinder/ Reservoir Hose on the following vehicles: ? 2013-2015 Dodge Dart (PF) ? 2014-2015 Jeep Cherokee (KL)
Source components: PARKING BRAKE:DRIVELINE:HYDRAULIC:HOSES, LINES/PIPING, AND FITTINGS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Clutch Pedal Operation X62 Extended Warranty This bulletin involves the replacement of the hydraulic clutch master cylinder and reservoir hose. Some customers may experience a reduction in clutch pedal stroke.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Occupant Restraint Controller (ORC) For PF, KL or UF Vehicles ONLY:~ Prior to replacing ORC part numbers, please contact FCA engineering if ANY of the following Diagnostic trouble codes are Stored or Active in the ORC module:~ DTC: B223D-00 - OCM DTC Present~ DTC: B0050-13 - Driver Seatbelt Sensor-Circuit Open~ DTC: B0052-13 - Passenger Seatbelt Sensor-Circuit Open~ DTC: B00B5-13 - Driver Seat Track Position Restraints Sensor-Circuit Open~ DTC: B00C5-13 - Passenger Seat Track Position Restraints Sensor-Circuit Open~ DTC: B0028-13 - Right Side Seat Deployment Squib 1-Circuit Open~ DTC: B0020-13 - Left Side Seat Deployment Squib 1-Circuit Open~ Execute DealerCONNECT / TechCONNECT Diagnostic Procedures to assess potential defects to devices connected to the ORC Module depending on the active or stored Diagnostic Trouble Code. If no defects are detected, verify wiring connectivity between the ORC Module and the component associated with the Diagnostic Trouble Code. Investigate connector pins and wire harness terminals for bent, corroded, or spread conditions. If no response within 15 minutes, proceed with repair.~ FCA Engineering Contacts:~ Jay Nagle (ORC Module, Driver/passenger seat track position sensor for PF, KL or UF Vehicles ONLY) @ cell (248) 420-4294 or jay.nagle@external.fcagroup.com~ Malcolm Whitehouse (OCM Module - PF,KL, or UF Vehicles ONLY)@248-462-4703 or Malcolm.Whitehouse@fcagroup.com.~ Bill Winfrey (Driver/Passenger Buckle Switch, Passenger/Driver Seat Thorax Airbags) @ cell (248) 941-9221 or william.winfrey@fcagroup.com~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Occupant Restraint Controller (ORC) For PF, KL or UF Vehicles ONLY:~ Prior to replacing ORC part numbers, please contact FCA engineering if the following Diagnostic trouble codes are Stored or Active in the ORC module:~ DTC: B223D-00 - OCM DTC Present~ DTC: B0050-13 - Driver Seatbelt Sensor-Circuit Open~ DTC: B0052-13 - Passenger Seatbelt Sensor-Circuit Open~ DTC: B00B5-13 - Driver Seat Track Position Restraints Sensor-Circuit Open~ DTC: B00C5-13 - Passenger Seat Track Position Restraints Sensor-Circuit Open~ DTC: B0028-13 - Right Side Seat Deployment Squib 1-Circuit Open~ DTC: B0020-13 - Left Side Seat Deployment Squib 1-Circuit Open~ Execute DealerCONNECT / TechCONNECT Diagnostic Procedures to assess potential defects to devices connected to the ORC Module depending on the active or stored Diagnostic Trouble Code. If no defects are detected, verify wiring connectivity between the ORC Module and the component associated with the Diagnostic Trouble Code. Investigate connector pins and wire harness terminals for bent,corroded,or spread conditions. If no response within 15 minutes, proceed with repair.~ FCA Engineering Contacts:~ Jay Nagle (ORC Module, OCM module, Driver/passenger seat track position sensor for PF, KL or UF Vehicles ONLY) @ cell (248) 420-4294 or jay.nagle@external.fcagroup.com~ Bill Winfrey (Driver/Passenger Buckle Switch, Passenger/Driver Seat Thorax Airbags) @ cell (248) 941-9221 or william.winfrey@fcagroup.com
Source components: ELECTRICAL SYSTEM · EQUIPMENT · SEAT BELTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Occupant Restraint Controller (ORC) For PF, KL or UF Vehicles ONLY:~ Prior to replacing ORC part numbers, please contact FCA engineering if the following Diagnostic trouble codes are Stored or Active in the ORC module:~ DTC: B223D-00 - OCM DTC Present~ DTC: B0050-13 - Driver Seatbelt Sensor-Circuit Open~ DTC: B0052-13 - Passenger Seatbelt Sensor-Circuit Open~ DTC: B00B5-13 - Driver Seat Track Position Restraints Sensor-Circuit Open~ DTC: B00C5-13 - Passenger Seat Track Position Restraints Sensor-Circuit Open~ DTC: B0028-13 - Right Side Seat Deployment Squib 1-Circuit Open~ DTC: B0020-13 - Left Side Seat Deployment Squib 1-Circuit Open~ Execute DealerCONNECT / TechCONNECT Diagnostic Procedures to assess potential defects to devices connected to the ORC Module depending on the active or stored Diagnostic Trouble Code. If no defects are detected, verify wiring connectivity between the ORC Module and the component associated with the Diagnostic Trouble Code. Investigate connector pins and wire harness terminals for bent,corroded,or spread conditions. If no response within 15 minutes, proceed with repair.~ FCA Engineering Contacts:~ Jay Nagle (ORC Module, OCM module, Driver/passenger seat track position sensor for PF, KL or UF Vehicles ONLY) @ cell (248) 420-4294 or jay.nagle@external.fcagroup.com~ Bill Winfrey (Driver/Passenger Buckle Switch, Passenger/Driver Seat Thorax Airbags) @ cell (248) 941-9221 or william.winfrey@fcagroup.com
Source components: ELECTRICAL SYSTEM · SEAT BELTS · SEATS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Occupant Restraint Controller (ORC) For PF, KL or UF Vehicles ONLY:~ Prior to replacing ORC part numbers, please contact FCA engineering if the following Diagnostic trouble codes are Stored or Active in the ORC module:~ DTC: B223D-00 - OCM DTC Present~ DTC: B0050-13 - Driver Seatbelt Sensor-Circuit Open~ DTC: B0052-13 - Passenger Seatbelt Sensor-Circuit Open~ DTC: B00B5-13 - Driver Seat Track Position Restraints Sensor-Circuit Open~ DTC: B00C5-13 - Passenger Seat Track Position Restraints Sensor-Circuit Open~ DTC: B0028-13 - Right Side Seat Deployment Squib 1-Circuit Open~ DTC: B0020-13 - Left Side Seat Deployment Squib 1-Circuit Open~ Execute DealerCONNECT / TechCONNECT Diagnostic Procedures to assess potential defects to devices connected to the ORC Module depending on the active or stored Diagnostic Trouble Code. If no defects are detected, verify wiring connectivity between the ORC Module and the component associated with the Diagnostic Trouble Code. Investigate connector pins and wire harness terminals for bent,corroded,or spread conditions. If no response within 15 minutes, proceed with repair.~ FCA Engineering Contacts:~ Jay Nagle (ORC Module, OCM module, Driver/passenger seat track position sensor for PF, KL or UF Vehicles ONLY) @ cell (248) 420-4294 or jay.nagle@external.fcagroup.com~ Bill Winfrey (Driver/Passenger Buckle Switch, Passenger/Driver Seat Thorax Airbags) @ cell (248) 941-9221 or william.winfrey@fcagroup.com
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) · P050D - Cold Start Rough Idle. · P0335 - Crankshaft Position Sensor Circuit. · P1607 - PCM Internal Shutdown Timer Rationality. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - EVAP System Small Leak. · P0480 - Cooling Fan 1 Control Circuit/Open. · U0402 - Implausible Data Received From TCM. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0441 - Evap Purge System Performance. · P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: · Engine Startup Flare and Idle Surge. · Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) · **P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range.** · U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. · P1185 - General Pressure Sensor Correlation. · P050D - Cold Start Rough Idle. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING · SERVICE BRAKES, HYDRAULIC · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) · P050D - Cold Start Rough Idle. · P0335 - Crankshaft Position Sensor Circuit. · P1607 - PCM Internal Shutdown Timer Rationality. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - EVAP System Small Leak. · P0480 - Cooling Fan 1 Control Circuit/Open. · U0402 - Implausible Data Received From TCM. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0441 - Evap Purge System Performance. · P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: · Engine Startup Flare and Idle Surge. · Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) · **P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range.** · U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. · P1185 - General Pressure Sensor Correlation. · P050D - Cold Start Rough Idle. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING · SERVICE BRAKES, HYDRAULIC · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. · P0441 - Evap Purge System Performance. · P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: · Engine Startup Flare and Idle Surge. · Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) · **P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range.** · U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. · P1185 - General Pressure Sensor Correlation. · P050D - Cold Start Rough Idle. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050B - Cold Start Ignition T
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING · SERVICE BRAKES, HYDRAULIC · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Multi-Air Actuator Assembly For 2.4 Tigershark Engine ONLY: When attempting to diagnose P Codes related to the MultiAir Unit, please note that there are multiple causes listed for each in the diagnostic procedure. This procedure must be followed to ensure the correct condition is being addressed. ~ Please verify the following (as listed in the first step in diagnostics) is not present before attempting repair:~ - Low Engine Oil - Incorrect oil filter that does not meet OEM specifications - Oil Dirty or Deteriorated (Lack of scheduled oil changes) - Incorrect Oil Viscosity/Weight - Engine Oil Contaminated (i.e. coolant and/or fuel) - Clogged Oil Galley Screen/Filter (top of block - feeds Multi-Air Unit) If there are any questions please contact: Seth Nankee at cell: (248) 303-5434 seth.nankee@fcagroup.com If no response within 15 minutes, please continue with diagnostics/repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Multi-Air Actuator Assembly For 2.4 Tigershark Engine ONLY: When attempting to diagnose P Codes related to the MultiAir Unit, please note that there are multiple causes listed for each in the diagnostic procedure. This procedure must be followed to ensure the correct condition is being addressed. ~ Please verify the following (as listed in the first step in diagnostics) is not present before attempting repair:~ - Low Engine Oil - Incorrect oil filter that does not meet OEM specifications - Oil Dirty or Deteriorated (Lack of scheduled oil changes) - Incorrect Oil Viscosity/Weight - Engine Oil Contaminated (i.e. coolant and/or fuel) - Clogged Oil Galley Screen/Filter (top of block - feeds Multi-Air Unit) If there are any questions please contact: Seth Nankee at cell: (248) 303-5434 seth.nankee@fcagroup.com If no response within 15 minutes, please continue with diagnostics/repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Multi-Air Actuator Assembly For 2.4 Tigershark Engine ONLY: When attempting to diagnose P Codes related to the MultiAir Unit, please note that there are multiple causes listed for each in the diagnostic procedure. This procedure must be followed to ensure the correct condition is being addressed. ~ Please verify the following (as listed in the first step in diagnostics) is not present before attempting repair:~ - Low Engine Oil - Incorrect oil filter that does not meet OEM specifications - Oil Dirty or Deteriorated (Lack of scheduled oil changes) - Incorrect Oil Viscosity/Weight - Engine Oil Contaminated (i.e. coolant and/or fuel) - Clogged Oil Galley Screen/Filter (top of block - feeds Multi-Air Unit) If there are any questions please contact: Seth Nankee at cell: (248) 303-5434 seth.nankee@fcagroup.com If no response within 15 minutes, please continue with diagnostics/repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A/C Compressor This applies to 2015 and 2016 KL, UF and PF. Before replacing the AC compressor for noise, leaks , or for an inop condition:~ After these questions have been answered please call one of the individuals below.~ 1) Check all AC plumbing connection for leaks with UV light. Any leaks found?~ 2) Does compressor pulley and clutch hub turn freely, or are they seized?~ 3) What was the amount of the recovered refrigerant?~ After these questions have been answered please call one of the individuals below:~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ If the compressor is replaced, then:~ 4) Drain oil from compressor. What was quantity of oil recovered?
NHTSA source summary · Original PDF not reviewed by Recallfolio
Panasonic 8.4" CTP/FCTP Radio, Update Failure Issue 1: Hand Free Module inoperative, can't pair phone: - Do not replace the radio for phone issues. The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 3; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"FLASH: TRANSMISSION SHIFT AND DRIVABILITY ENHANCEMENTS THIS BULLETIN INVOLVES REPROGRAMMING THE TRANSMISSION CONTROL MODULE (TCM) WITH THE LATEST AVAILABLE SOFTWARE. CUSTOMERS MAY EXPERIENCE ONE OR ALL OF THE FOLLOWING: · **ENGINE REVVING BEFORE UP-SHIFTING AT LOW TO MODERATE SPEEDS. (2.4L ONLY) · DELAYED SHIFTING / NOT WANTING TO SHIFT UNTIL ABOUT 3500 RPM, WHEN DRIVING STRAIGHT. (2.4L ONLY) · SHUDDERING OR BUMPS WHILE MOVING AND STEPPING ON THE ACCELERATOR PEDAL. (2.4L ONLY)** · A DELAYED UP-SHIFT. THIS CONDITION MAY BE NOTICED WHEN CORNERING WITH A LIGHT ACCELERATION AND SPEEDS UP TO 40 KPH (25 MPH) CAUSING HIGH ENGINE RPM."
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) · P050D - Cold Start Rough Idle. · P0335 - Crankshaft Position Sensor Circuit. · P1607 - PCM Internal Shutdown Timer Rationality. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - EVAP System Small Leak. · P0480 - Cooling Fan 1 Control Circuit/Open. · U0402 - Implausible Data Received From TCM. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0441 - Evap Purge System Performance. · P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: · Engine Startup Flare and Idle Surge. · Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) · U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. · P1185 - General Pressure Sensor Correlation. · P050D - Cold Start Rough Idle. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050B - Cold Start Ignition Timing Performance. · P061A - Level 2 Torque Performance. · P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). · Low Idle Speed After Cold Start between -10°C to 0°C (14°F to 32°F). · Cold Idle Surge With AC Engaged
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING · SERVICE BRAKES · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: · Engine Startup Flare and Idle Surge. · Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) · U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. · P1185 - General Pressure Sensor Correlation. · P050D - Cold Start Rough Idle. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050B - Cold Start Ignition Timing Performance. · P061A - Level 2 Torque Performance. · P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). In addition to the DTCs above the following improvements have been made: · Low Idle Speed After Cold Start between -10°C to 0°C (14°F to 32°F). · Cold Idle Surge With AC Engaged
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FLASH: 2.4L POWERTRAIN DIAGNOSTIC AND SYSTEM IMPROVEMENTS. BULLETIN INVOLVES REPROGRAMMING THE POWERTRAIN CONTROL MODULE (PCM) WITH THE LATEST AVAILABLE SOFTWARE. A SMALL NUMBER OF CUSTOMERS MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION OR ONE OR MORE OF THE FOLLOWING CONDITIONS. UPON FURTHER INVESTIGATION THE TECHNICIAN MAY FIND THE FOLLOWING DIAGNOSTIC TROUBLE CODES (DTCS) SET IN THE PCM, MEMORY:2015 UF VEHICLES WITH (SALES CODES ED6, ED8)· P050D - COLD START ROUGH IDLE. P0335 - CRANKSHAFT POSITION SENSOR CIRCUIT. P1607 - PCM INTERNAL SHUTDOWN TIMER RATIONALITY. P0133 - O2 SENSOR 1/1 SLOW RESPONSE. P0456 - EVAP SYSTEM SMALL LEAK.· P0480 - COOLING FAN 1 CONTROL CIRCUIT/OPEN. U0402 - IMPLAUSIBLE DATA RECEIVED FROM TCM. P2172 - HIGH AIRFLOW/VACUUM LEAK DETECTED.P1D73 - AGS PERFORMANCE. U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE. · P0441 - EVAP PURGE SYSTEM PERFORMANCE. · P0116 - ENGINE COOLANT TEMPERATURE SENSOR 1 PERFORMANCE.IN ADDITION TO THE DTCS ABOVE THE FOLLOWING IMPROVEMENTS HAVE BEEN MADE:ENGINE STARTUP FLARE AND IDLE SURGE.IMPROVED VEHICLE ACCELERATION. 2015 PF VEHICLES WITH (SALES CODES ED6, ED8)U0401 - IMPLAUSIBLE DATA RECEIVED FROM ECM/PCM - SIGNAL INVALID. P1185 - GENERAL PRESSURE SENSOR CORRELATION.P050D - COLD START ROUGH IDLE. P0133 - O2 SENSOR 1/1 SLOW RESPONSE. P0456 - EVAP SYSTEM SMALL LEAK.P219A - BANK 1 AIR-FUEL RATIO IMBALANCE. P2172 - HIGH AIRFLOW/VACUUM LEAK DETECTED.P1D73 - AGS PERFORMANCE.U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE. P0116 - ENGINE COOLANT TEMPERATURE SENSOR 1 PERFORMANCE. P050B - COLD START IGNITION TIMING PERFORMANCE. P061A - LEVEL 2 TORQUE PERFORMANCE.P2172 - HIGH AIRFLOW/VACUUM LEAK DETECTED (INSTANTANEOUS ACCUMULATION).IN ADDITION TO THE DTCS ABOVE THE FOLLOWING IMPROVEMENTS HAVE BEEN MADE: LOW IDLE SPEED AFTER COLD START BETWEEN -10°C TO 0°C (14°F TO 32°F).
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) · P050D - Cold Start Rough Idle. · P0335 - Crankshaft Position Sensor Circuit. · P1607 - PCM Internal Shutdown Timer Rationality. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - EVAP System Small Leak. · P0480 - Cooling Fan 1 Control Circuit/Open. · U0402 - Implausible Data Received From TCM. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0441 - Evap Purge System Performance. · P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: · Engine Startup Flare and Idle Surge. · Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) · **U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. · P1185 - General Pressure Sensor Correlation.** · P050D - Cold Start Rough Idle. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050B - Cold Start Ignition Timing Performance. · P061A - Level 2 Torque Performance. · P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). In addition to the DTCs above the following improvements have been made:
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING · SERVICE BRAKES, HYDRAULIC · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) · P050D - Cold Start Rough Idle. · P0335 - Crankshaft Position Sensor Circuit. · P1607 - PCM Internal Shutdown Timer Rationality. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - EVAP System Small Leak. · P0480 - Cooling Fan 1 Control Circuit/Open. · U0402 - Implausible Data Received From TCM. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0441 - Evap Purge System Performance. · P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: · Engine Startup Flare and Idle Surge. · Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) · **U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. · P1185 - General Pressure Sensor Correlation.** · P050D - Cold Start Rough Idle. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050B - Cold Start Ignition Timing Performance. · P061A - Level 2 Torque Performance. · P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation).
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: Engine Startup Flare and Idle Surge. Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) **U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. P1185 - General Pressure Sensor Correlation.** P050D - Cold Start Rough Idle. P0133 - O2 Sensor 1/1 Slow Response. P0456 - Evap System Small Leak. P219A - Bank 1 Air-Fuel Ratio Imbalance. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0116 - Engine Coolant Temperature Sensor 1 Performance. P050B - Cold Start Ignition Timing Performance. P061A - Level 2 Torque Performance. P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). In addition to the DTCs above the following improvements have been made: Low Idle Speed After Cold Start between -10°C to 0°C (14°F to 32°F). Cold Idle Surge With AC Eng
NHTSA source summary · Original PDF not reviewed by Recallfolio
9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
Source components: ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:FILTER/SCREEN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) · **P050D - Cold Start Rough Idle. · P0335 - Crankshaft Position Sensor Circuit. · P1607 - PCM Internal Shutdown Timer Rationality. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak.** · P0480 - Cooling Fan 1 Control Circuit/Open. · U0402 - Implausible Data Received From TCM. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0441 - Evap Purge System Performance. · P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: · Engine Startup Flare and Idle Surge. · Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) · P050D - Cold Start Rough Idle. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050B - Cold Start Ignition Timing Performance. · P061A - Level 2 Torque Performance. · P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). In addition to the DTCs above the following improvements have been made: · Low Idle Speed After Cold Start between -10°C to 0°C (14°F to 32°F).
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) · **P050D - Cold Start Rough Idle. · P0335 - Crankshaft Position Sensor Circuit. · P1607 - PCM Internal Shutdown Timer Rationality. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak.** · P0480 - Cooling Fan 1 Control Circuit/Open. · U0402 - Implausible Data Received From TCM. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0441 - Evap Purge System Performance. · P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: · Engine Startup Flare and Idle Surge. · Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) · P050D - Cold Start Rough Idle. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050B - Cold Start Ignition Timing Performance. · P061A - Level 2 Torque Performance. · P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation).
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) · **P050D - Cold Start Rough Idle. · P0335 - Crankshaft Position Sensor Circuit. · P1607 - PCM Internal Shutdown Timer Rationality. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak.** · P0480 - Cooling Fan 1 Control Circuit/Open. · U0402 - Implausible Data Received From TCM. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0441 - Evap Purge System Performance. · P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: · Engine Startup Flare and Idle Surge. · Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) · P050D - Cold Start Rough Idle. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050B - Cold Start Ignition Timing Performance. · P061A - Level 2 Torque Performance. · P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). In addition to the DTCs above the following improvements have been made: · Low Idle Speed After Cold Start between -10°C to 0°C (14°F to 32°F). · Cold Idle Surge With AC Engaged.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.0L Diagnostic And System Improvements software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): · **P0335-00 - Crankshaft Position Sensor Circuit.** · P030X - Cylinder X Misfire improvements when P0335 (Crankshaft Position Sensor Circuit) is present. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P0456 - EVAP System Small Leak. · P0441 - EVAP Purge System Performance. · P1D73 - AGS (Active Grill Shutter) Performance. · U0140 - Lost Communication With Body Control Module (BCM). In addition to the above conditions, a customer may also experience the following symptoms: · ASD/Fuel pump relay cycling during remote start. · E15 cold start improvements in temperatures below -7°C (20°F).
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING · FUEL SYSTEM, GASOLINE · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.0L Diagnostic And System Improvements software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): · **P0335-00 - Crankshaft Position Sensor Circuit.** · P030X - Cylinder X Misfire improvements when P0335 (Crankshaft Position Sensor Circuit) is present. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P0456 - EVAP System Small Leak. · P0441 - EVAP Purge System Performance. · P1D73 - AGS (Active Grill Shutter) Performance. · U0140 - Lost Communication With Body Control Module (BCM). In addition to the above conditions, a customer may also experience the following symptoms: · ASD/Fuel pump relay cycling during remote start. · E15 cold start improvements in temperatures below -7°C (20°F).
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Panasonic 8.4" CTP/FCTP Radio, Update Failure Issue 1: Hand Free Module inoperative, can't pair phone: - Do not replace the radio for phone issues. The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 3.; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio. ~
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.0L Diagnostic And System Improvements software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): · **P0335-00 - Crankshaft Position Sensor Circuit.** · P030X - Cylinder X Misfire improvements when P0335 (Crankshaft Position Sensor Circuit) is present. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P0456 - EVAP System Small Leak. · P0441 - EVAP Purge System Performance. · P1D73 - AGS (Active Grill Shutter) Performance. · U0140 - Lost Communication With Body Control Module (BCM). In addition to the above conditions, a customer may also experience the following symptoms: · ASD/Fuel pump relay cycling during remote start. · E15 cold start improvements in temperatures below -7°C (20°F).
Source components: ENGINE · ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV) · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Panasonic 8.4" CTP/FCTP Radio, Update Failure Issue 1: Hand Free Module inoperative, can't pair phone: - Do not replace the radio for phone issues. The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 3.; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio. ~
NHTSA source summary · Original PDF not reviewed by Recallfolio
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
NHTSA source summary · Original PDF not reviewed by Recallfolio
(X66) RB5 & RB6 8.4 Nav Radio - 2014-2015 Dodge Dart (PF). To announce an extended warranty on the RB5 & RB6 8.4 Nav Radio on the following vehicles: 2014-2015 Dodge Dart (PF)
NHTSA source summary · Original PDF not reviewed by Recallfolio
RB5 RB6 Radio Software Enhancements (X66 Warranty Extension) This bulletin involves updating the radio and navigation software or replacing the radio. SYMPTOM/CONDITION: Customers may experience one or more of the following symptoms/conditions: · Radio screen will lock up and reset intermittently. · Unable to turn on heated seats; screen icon is greyed out. · Navigation screen goes blank. · Navigation system freezes/locks up. · Incorrect routing directions to fuel stations when using Travel Link. · Navigation icon shows the vehicle going backward when it?s moving forward. · Map checksum error may be displayed when attempting to update the navigation system maps.
NHTSA source summary · Original PDF not reviewed by Recallfolio
(X66) RB5 & RB6 8.4 Nav Radio - 2014-2015 Dodge Dart (PF). To announce an extended warranty on the RB5 & RB6 8.4 Nav Radio on the following vehicles: 2014-2015 Dodge Dart (PF)
NHTSA source summary · Original PDF not reviewed by Recallfolio
MODULE, Transmission Control This generic TCM must be flashed with the ignition in the accessory position. Attempts to flash with the ignition in the run position may result in flash failures
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.0L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): · **P030X - Cylinder X Misfire improvements when P0335 (Crankshaft Position Sensor Circuit) is present.** · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P0456 - EVAP System Small Leak. · P0441 - EVAP Purge System Performance. · P1D73 - AGS (Active Grill Shutter) Performance. · U0140 - Lost Communication With Body Control Module (BCM). In addition to the above conditions, a customer may also experience the following symptoms: · ASD/Fuel pump relay cycling during remote start. · E15 cold start improvements in temperatures below -7°C (20°F).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) ? Improved vehicle acceleration. ? P0480 - Cooling Fan 1 Control Circuit/Open. ? P0456 - Evap System Small Leak. ? U0402 - Implausible Data Received From TCM. ? Engine Startup Flare and Idle Surge. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0441 - Evap Purge System Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. 2015 PF Vehicles with (Sales Codes ED6, ED8) ? P0133 - O2 Sensor 1/1 Slow Response. ? P0456 - Evap System Small Leak. ? Low Idle Speed After Cold Start between 14°F to 32°F (-10°C to 0°C). ? Cold Idle Surge With AC Engaged. ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10°F to 40°F (-12°C to 4.5°C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050B - Cold Start Ignition Timing Performance. ? P050D - Cold Start Rough Idle. ? P061A - Level 2 Torque Performance. ? P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). 2013-2014 PF Vehicles (Sales Codes ED6)
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 1.4L Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: 2016 Dart ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. 2015 Dart ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent. ? P104C - Cylinder 4 Oil Supply Solenoid Valve Overcurrent. ? P1D73 - Active Grill Shutter (AGS) Performance. ? P113D - O2 Sensor 1/1 Slow Response. ? Engine bump sensation felt during moderate to heavy acceleration over 3,500 RPM. ? P061A - Level 2 torque performance set. ? Engine difficult to restart after cold or warm soak periods. ? Intermittent high coolant temp warning lamp illumination when using cruise control. Condition occurs in conjunction with the P061A DTC listed above. ? Poor A/C performance primarily during extended hot idle and/or low speed driving conditions. Applies to vehicles built with 1234YF refrigerant sales code XFC. ? Cold start difficulty below -10°C (14°F) ambient temperatures. Engine cranks fast and possibly does not start due to loss of crankshaft synchronization until key cycle is performed. (Vehicles built on or after August 23, 2014 (MDH 0823XX) and on or before June 16, 2015 (MDH 0616XX)). 2014 Dart ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylind
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: Accelerator Pedal Issue Description: Vehicle has accelerator pedal fault code. Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
Source components: VEHICLE SPEED CONTROL · VEHICLE SPEED CONTROL:ACCELERATOR PEDAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: Panasonic 8.4" CTP/FCTP Radio, Update Failure Issue Description: Issue 1; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 2.; During a Travel Link software update.....The radio locks up and displays "Software Missing" with a green screen. Please contact Nabil Issa at cell (248) 941-8720 or Dave Clemons at cell (248) 520-0419. IMPORTANT - Do not clear codes, perform a battery reset, or remove the radio before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. ~ Issue 3.; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Gaurav Saxena at cell (248) 260-0583 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio. ~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: Nut - Front Hub & Bearing Issue Description: Whenever replacing the front Hub & Bearing Halfshaft Nut, make sure to torque to proper spec of 150 ft/lbs (200 Nm) and crimp according to procedure in TechConnect. (This torrque is higher than other platforms). Failure to do so will result in eventual Hub & Bearing failure (noise).~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: HVAC Blower Assembly Issue Description: Blower Motor either making noise or is inoperative (even intermittently). Before replacing any of the part numbers listed above, please call any of the following people for each vehicle type. (If you don't get an answer within 15 minutes, then proceed with the repair.):~ WD/WK--68224166AB - Front Ken Deneau, cell (248) 765-0288~ 68089094AA - Rear Pat Presti- cell (248) 379-0972~ KL/UF/PF- 68223053AB, 68225055AA Mark Ware, cell (248) 705-3469~ F500- 68093422AB,Matt Sasina, cell (248) 464-4982 or Bryan Bremer cell (248) 429-9014~ RT- 68029719AB - Front, Chad Holcomb at cell (734)-634-3679 05183147AA - Rear, Ken Deneau, cell (248) 765-0288
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: Motor, Sunroof Issue Description: If looking to replace the sunroof motor and these conditions are occurring:~ 1) Vent switch does not work.~ 2) Open switch only moves the sunroof an inch no matter how long the switch is held.~ 3) When the close switch is used, sunroof closes but then goes into vent.~ The sunroof motor does not need to be replaced, but only reinitialized. Please follow reinitialization procedure available in TechCONNECT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8). ? Improved vehicle acceleration. ? P0480 - Cooling Fan 1 Control Circuit/Open. ? P0456 - Evap System Small Leak. ? U0402 - Implausible Data Received From TCM. ? Engine Startup Flare and Idle Surge. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0441 - Evap Purge System Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. 2015 PF Vehicles with (Sales Codes ED6, ED8), built on or before July 24, 2015 (MDH 0724XX). ? Low Idle Speed After Cold Start between 14°F to 32°F (-10°C to 0°C). ? Cold Idle Surge With AC Engaged. ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10°F to 40°F (-12°C to 4.5°C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050B - Cold Start Ignition Timing Performance. ? P050D - Cold Start Rough Idle. ? P061A - Level 2 Torque Performance. ? P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2172 - High Airflow/Vacuum Leak Detec
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8). ? Improved vehicle acceleration. ? P0480 - Cooling Fan 1 Control Circuit/Open. ? P0456 - Evap System Small Leak. ? U0402 - Implausible Data Received From TCM. ? Engine Startup Flare and Idle Surge. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0441 - Evap Purge System Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. 2015 PF Vehicles with (Sales Codes ED6, ED8), built on or before July 24, 2015 (MDH 0724XX). ? Low Idle Speed After Cold Start between 14°F to 32°F (-10°C to 0°C). ? Cold Idle Surge With AC Engaged. ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10°F to 40°F (-12°C to 4.5°C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050B - Cold Start Ignition Timing Performance. ? P050D - Cold Start Rough Idle. ? P061A - Level 2 Torque Performance. ? P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2172 - High Airflow/Vacuum Leak Detec
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8). ? Improved vehicle acceleration. ? P0480 - Cooling Fan 1 Control Circuit/Open. ? P0456 - Evap System Small Leak. ? U0402 - Implausible Data Received From TCM. ? Engine Startup Flare and Idle Surge. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0441 - Evap Purge System Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. 2015 PF Vehicles with (Sales Codes ED6, ED8), built on or before July 24, 2015 (MDH 0724XX). ? Low Idle Speed After Cold Start between 14°F to 32°F (-10°C to 0°C). ? Cold Idle Surge With AC Engaged. ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10°F to 40°F (-12°C to 4.5°C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050B - Cold Start Ignition Timing Performance. ? P050D - Cold Start Rough Idle. ? P061A - Level 2 Torque Performance. ? P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2172 - High Airflow/Vacuum Leak Detec
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: Cruise Control Switch Issue Description: Before ordering or replacing this part please contact Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: Cruise Control Switch Issue Description: Before ordering or replacing this part please contact Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: Cruise Control Switch Issue Description: Before ordering or replacing this part please contact Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hands Free Feature Inoperative This bulletin involves updating the Convergence Telematics Module (CTM) software. NOTE: Convergence Telematics Module (CTM) was also known as the Hands Free Module (HFM). The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection one or more of the following DTCs may be found: ? U11F6-00 Lost Communication With Convergence Telematics Module. ? U11F6-87 Lost Communication With Convergence Telematics Module - Missing Message.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hands Free Feature Inoperative This bulletin involves updating the Convergence Telematics Module (CTM) software. NOTE: Convergence Telematics Module (CTM) was also known as the Hands Free Module (HFM). The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection one or more of the following DTCs may be found: ? U11F6-00 Lost Communication With Convergence Telematics Module. ? U11F6-87 Lost Communication With Convergence Telematics Module - Missing Message.
Source components: COMMUNICATION:MANUFACTURER TELEMATICS · ELECTRICAL SYSTEM · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hands Free Feature Inoperative This bulletin involves updating the Convergence Telematics Module (CTM) software. NOTE: Convergence Telematics Module (CTM) was also known as the Hands Free Module (HFM). The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection one or more of the following DTCs may be found: ? U11F6-00 Lost Communication With Convergence Telematics Module. ? U11F6-87 Lost Communication With Convergence Telematics Module - Missing Message.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Brake Squeak/Squeal Noise This bulletin involves replacing the front brake rotors, front brake pads, and related hardware. The customer may describe a front brake squeak/squeal high frequency noise in the 6-7 kHz range while stopping, noise may be intermittent (not every stop).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Brake Squeak/Squeal Noise This bulletin involves replacing the front brake rotors, front brake pads, and related hardware. The customer may describe a front brake squeak/squeal high frequency noise in the 6-7 kHz range while stopping, noise may be intermittent (not every stop).
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · SERVICE BRAKES.