2018 Chrysler PACIFICA Manufacturer communications & TSBs.Page 5
Original record summaries, dates and identifiers for this model-year. Records 401–470 of 470, ordered newest first. Dated records on this page: Mar 20, 2013–Mar 24, 2020.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Mar 24, 2020Service Bulletin/Repair Instructions
08-042-20
NHTSA communication ID: 10175573
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processer (AHCP) Diagnostic and System Updates This bulletin involves updating the HCP and the AHCP with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may one or more of the following DTCs have been set:P0CF3-00 - Control Pilot Circuit Open(North America Only). P0CF4-00 - Control Pilot Circuit Performance(North America Only). P0D57-00 - Proximity Detection Circuit Performance(North America Only). P1C68-00 - Hybrid Perf Engine Speed Above Target Idle Speed During Autostop(APAC China Only).
Source components: BACK OVER PREVENTION · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processer (AHCP) Diagnostic and System Updates This bulletin involves updating the HCP and the AHCP with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may one or more of the following DTCs have been set:P0CF3-00 - Control Pilot Circuit Open(North America Only). P0CF4-00 - Control Pilot Circuit Performance(North America Only). P0D57-00 - Proximity Detection Circuit Performance(North America Only). P1C68-00 - Hybrid Perf Engine Speed Above Target Idle Speed During Autostop(APAC China Only).
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN:MANUAL TRANSMISSION:SHIFT PATTERN INDICATOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processer (AHCP) Diagnostic and System Updates This bulletin involves updating the HCP and the AHCP with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may one or more of the following DTCs have been set:P0CF3-00 - Control Pilot Circuit Open(North America Only). P0CF4-00 - Control Pilot Circuit Performance(North America Only). P0D57-00 - Proximity Detection Circuit Performance(North America Only). P1C68-00 - Hybrid Perf Engine Speed Above Target Idle Speed During Autostop(APAC China Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
COVER, Cylinder Head, Left/Right Prior to replacing the cylinder head cover on ANY 3.6L Pentastar Upgrade Engine, verify that there are no steel dowel pins pressed into the cylinder head. If dowels are present in the cylinder head please remove carefully without touching/damaging the cylinder head sealing surface.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CENTER STACK, Upper (Front Radio Display) 1) If Front Radio Display is experiencing a Black Screen, please verify radio Software is up to date. 2) For concern of a "Yellow Band" on the center stack display, swapping the radio or display will NOT resolve the issue. The issue was corrected in a recently released software update. Please visit Service Library for the latest in diagnostic information. For any questions, please contact: Anmol Shergill (248) 512-1207 - Anmol.Shergill@external.fcagroup.com or Ashikur Rahman (248) 512- 6715 - Ashikur.Rahman@external.fcagroup.com
NHTSA source summary · Original PDF not reviewed by Recallfolio
CENTER STACK, Upper (Front Radio Display) 1) If Front Radio Display is experiencing a Black Screen, please verify radio Software is up to date. 2) For concern of a "Yellow Band" on the center stack display, swapping the radio or display will NOT resolve the issue. The issue was corrected in a recently released software update. Please visit Service Library for the latest in diagnostic information. For any questions, please contact: Anmol Shergill (248) 512-1207 - Anmol.Shergill@external.fcagroup.com or Ashikur Rahman (248) 512- 6715 - Ashikur.Rahman@external.fcagroup.com
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI-eVT Transmission - China Variant & 9 inertia ring bolts For SI-eVT Transmission ONLY: Replace the nine (9) flywheel to damper bolts (68382486AA) when replacing the SI-eVT per TechConnect procedure. SI-eVTs built prior to January 11, 2019 had a 05192374AB level cooler. Using service SI-evT built after Jan 11 2019 with the 05192374AC level cooler requires new 68238385AB inlet hose and 68238386AC outlet hose. The service SI-eVT is shipped with a non-China wiring harness (68241331AC). China market replacement must replace wiring harness with 68368596AA. The China variant 68368596AA wiring harness has an interlock to the electrical charge door.
Source components: ELECTRICAL SYSTEM · FUEL SYSTEM, GASOLINE · POWER TRAIN · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI-eVT Transmission - China Variant & 9 inertia ring bolts For SI-eVT Transmission ONLY: Replace the nine (9) flywheel to damper bolts (68382486AA) when replacing the SI-eVT per TechConnect procedure. SI-eVTs built prior to January 11, 2019 had a 05192374AB level cooler. Using service SI-evT built after Jan 11 2019 with the 05192374AC level cooler requires new 68238385AB inlet hose and 68238386AC outlet hose. The service SI-eVT is shipped with a non-China wiring harness (68241331AC). China market replacement must replace wiring harness with 68368596AA. The China variant 68368596AA wiring harness has an interlock to the electrical charge door.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Video Routing Module (VRM) Enhancements For Rear Seat Entertainment System This bulletin involves updating the VRM software level to 19.12.10. Customers may experience the following:Black screen on both rear screens. Rear Seat Entertainment (RSE) remote control does not pair. When playing a video from a USB stick the video does not resume where itleft off after an ignition cycle. Video Screens do not turn on. Radio Uconnect theater button does not work. USB playback is choppy. The video system resets or does not function (Most likely to occur if the vehicle is cold or the battery voltage is too low). Upon further investigationthe technician may find that the following Diagnostic Trouble Code (DTC) has been set:B15AD-00 - Lost Low Voltage Differential Signal (LVDS) Connection With MediaPort 1. B15AE-00 - Lost Low Voltage Differential Signal (LVDS) Connection With MediaPort 2. B15AA-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Display1. B15AB-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Display2.Low Voltage Differential Signal (LVDS) DTCs (B15AD00, B15AE00, B15AB00, B15AA00) get falsely set when thevehicle is remote started. U11BB-00 - Lost Communication With Video Routing Module. In addition the following improvement is included.Blueborn cyber security patch.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GRILLE, Active Shutter When replacing Active Grille Shutter on vehicles built before April 10th, 2018 rearrange pin configuration in the AGS connector to MY 2019 configuration. Failure to do so will result in U11E9 Loss of Comm with AGS. Please view I-sheet in STAR parts for reference.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pentastar Upgrade Oil Fill Level after an Oil Change This bulletin involves rechecking the oil fill level after filling the engine to the correct specifications. The customer may describe that after an oil change they check their oil fill level and it is showing overfilled on the oil dipstick.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio and Back-up Camera Enhancements This bulletin involves updating the radio software level to 1848.24. Customers may experience one or more of the following: Green horizontal lines on back up display, in reverse (If this is the customer concern use camera LOP 18-60-02-Y7, on JL vehicles only). Ghost Touch, features, modes and App?s changing, without drivers input. Speaker pop noise when using Bluetooth device. When vehicle is first started the radio will reset and the time display shows 12:00. Audio distortion and volume fluctuation. Blank rear camera image in reverse (If this is the customer concern use camera LOP 18-60-02-Y7) JL only. Audio cutting in and out during memory recall. Ring tone too loud. AM/FM volume fluctuates. While in CarPlay® or AndroidAuto® Google® maps showing wrong location. Phone disconnected after first call. Black screen or White screen with vertical lines. PIN clear and volume locked while KeySense is used. Audio static while in SXM/SAT modes. Echo heard during Bluetooth phone calls. The radio is locked up. The radio remains on after ignition has been turned off. The radio resets. The radio screen turns black. The radio screen shows messages ?Software Update? or ?Reinsert USB Device? and displays that screen in a continuous loop.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LATCH, Liftgate For Liftgate latch not locking and/or unlocking intermittently, please verify there is no glass in the latch from the rear window breaking. Carefully inspect the part for small shards of glass.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
UConnect Theater Remote Before replacing the Remote Control for the Rear Seat Entertainment system due to pairing issues, ensure that the VRM and radio software is at the latest level. If remote pairing still fails at the newer software levels, perform a reset on the remote by simultaneously pressing the Play/Pause, Down, and Screen buttons and holding for about 5 seconds until the remote backlighting flashes. It is also suggested to turn the ignition off, close all the doors, and wait for the cluster to go to sleep. Key the car back to ACC and retry the pairing procedure. For any additional questions regarding part numbers, software levels, or support please call Mike Galiati at (248) 294-8754. If no response in 15 minutes, proceed with repair.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Seat Entertainment System Video Routing Module Please check the Uconnect software portal to verify the latest software is installed. If the VRM Module is not showing up in WiTech (or is unresponsive) and/or the rear screens are not functioning, before replacement follow the steps below: 1.) Check the part number of the Module, this will be the number above the barcode seen in the top corner of the module. if it is 68376134AE contact Mike Galiati at 248-294-8754 before troubleshooting. If no response in 15 minutes, proceed with repair. 2.) Disconnect and reconnect the 26-way power harness, if the module recovers check software is at the latest level 1750.13. 3.) If the Module does not recover in step 1, disconnect the BLUE mini-USB connector to the module and perform step 1 again. If the Module recovers, replace the USB port located next to the BlueRay player. If there are issues while using the Uconnect theater APP, black radio screen/does not open, but the rear screens are functional DO NOT replace the module. This is a radio software issue and not related to the Video Routing Module. If the above tip does not correct the issue, before replacing the Video Routing Module (VRM) for the Rear Seat Entertainment system in the Pacifica, please call Mike Galiati at (248) 294-8754. If no response in 15 minutes, proceed with repair.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following DTCs have been set: P06E9 - Engine Starter Performance, U0418 - Implausible Data Received From Brake System Control Module 1, U0432 - Invalid Data Received From Multi-Axis Acceleration Sensor Module, P06EF - Engine Restart Performance.Software update will help reduce engine crank time, setting a false P06EF, P00FD - Battery -B- State Of Charge Performance, C2222-68 - Improper Powerdown - Event Information, P0607-00 - ECU Internal Performance - ESM, U0402-00 - Implausible Data Received From TCM, U145D-00 - Implausible Data Received From TCM On D-PT, U1465-00 - Implausible Driver Shift Request Signal Received, P0456 - Evap System Small Leak. If no faults were found when performing normal diagnostic, perform this softwareupdate. P258B - Electronic Vacuum Pump Performance. P0503 - Vehicle Speed Sensor 1 Erratic. Customer may also experience one or more of the following:Customer or technician may be unable to read data information from the OBDII connector when using a generic scan tool (APAC only). Rough Idle. Vibration felt in the seat at Idle. Idle undershoot, just before a complete stop. Engine Start Stop (ESS) disabled during an autostart, requiring the driver to key restart. ESS message appears in the Electronics Vehicle Information Center (EVIC) ?Stop/Start Restart Required Fault Detected?. This software release also includes the following software enhancements:Prevent the ESS Aux battery from drying out on vehicles driven in hot regions and conditions. AGS controls modifications to reduce engine compartment temperatures. Limp home RPM correction in a double pedal fault scenario. Improvements to address an occasional engine stall during a panic brake situation from 45 kph (28 mp
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Bulletin sent to all dealers to update the firmware in the affected vehicles VMI computer. This removes the 1 to 2 second window in the VMIQ software programming immediately prior to the OEM and VMI computers go into 'sleep' mode. During that window, the OEM door operator module may not accept an open or close signal while manual door operation remains unaffected
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A/C Pressure Transducer A/C inoperative and diagnosis leads to pressure transducer. Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A/C Pressure Transducer A/C inoperative and diagnosis leads to pressure transducer. Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rain light sensor Rain sense wipers do not operate: 1. Visual Inspection--> Check if the sensor is visually OK. (all the pins are OK) Check that the Connector is NOT loose (Sensor must get a voltage from 9V to 16V) 2. Functional Checks Rain--> Steering column switch is in auto mode (sensor is active) it is necessary to splash water on the sensitive surface of the sensor to trigger wipes. check the same for different sensitivities When the rain sensitivity is increased (for example from level 0 to level 1), as an acknowledgement a single wipe is seen. (This is not a phantom wipe) and this single wipe is not seen when the rain sensitivity is decreased (from higher level to lower level) Light--> Steering column switch is in auto mode (sensor is active) block the light coming on the sensor from outside of the vehicle (use a opaque object), the head lamps should be activated 3. If the sensor seems functional, it is ideal to remove the silicon gel pad from the sensor, replace it with the new silicon gel pad instead of replacing the whole sensor. When servicing the LRSM please replace the silicon gel pad with a new silicon gel pad (PN 68224945AA) instead of replacing the whole sensor.
Source components: AIR BAGS · BACK OVER PREVENTION · ELECTRICAL SYSTEM · PARKING BRAKE · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI-eVT Transmission - China Variant The service SI-eVT is shipped with a non-China wiring harness (68241331AC). China market replacement must replace wiring harness with 68368596AA. The China variant 68368596AA wiring harness has an interlock to the electrical charge door.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI-eVT Transmission - China Variant The service SI-eVT is shipped with a non-China wiring harness (68241331AC). China market replacement must replace wiring harness with 68368596AA. The China variant 68368596AA wiring harness has an interlock to the electrical charge door.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
Source components: STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Return: Wiring Assy - Engine You have been identified as either having stock, or have stock in transit to your dealership. Please return stock packaged before 2016/07/31 (31 July, 2016)of follow ing part numbers:68176457AF, 68176459AF. Please return suspect parts back to your facing depot using Return Code 02, before 13 September, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
05182535AD - Lamp Assy ?Tail Light LT You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 05182535AD . See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Inspect and Return: Trim Cover Assy - A-Pillar Rt/Lt You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part numbers: 1ZA04DX9AE, 1ZA05DX9AE. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CBXDP361AA Return: Spacer Kit - Visor You have been identified as either having stock, or have stock in transit to your dealership. Please return stock of part number CBXDP361AA. Replacement part number is CBXDP361AB w hich is in stock and available for order. Please return suspect parts back to your facing depot using Return Code 02, before 16 September, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
1NT30XDVAC - Inspect and Return: Panel - Instrument Panel You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 1N T30XDVAC. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Inspect and Return: Solenoid Module - Transmission You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of follow ing part numbers:52120000AA, 52119435AF, 05078709AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Return: Lamp Assy - CHMSL& Cargo Light You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of follow ing part numbers:55372082AE, 55372082AD, 55372082AC, 55372082AB, 55372082AA. Replacement part number is 55372082AF w hich is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
P/N CBSZR068AA: Inspect & Return: Module Kit - Occupant Restraint You have been identified as either having stock, or have stock in transit to your dealership. Please return part number CBSZR068AA as per the QIR attached. Replacement part can be obtained by ordering the same part number (CBSZR068AA) Please return suspect parts back to your facing depot using Return Code 02, before 02 September, 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~