The manufacturer’s record · Page 1 of 3
Original record summaries, dates and identifiers for this model-year. Records 1–100 of 215, ordered newest first. Dated records on this page: Aug 17, 2016–Jun 18, 2026.
Back to 2013 Chrysler 200 problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 11034343
NHTSA source summary · Original PDF not reviewed by Recallfolio
Emissions Recall U67 - Catalytic Converter Efficiency - Dealer Notification (Revision 11)
Source components: ENGINE.
Source record 11034343 at NHTSANHTSA communication ID: 11022027
NHTSA source summary · Original PDF not reviewed by Recallfolio
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
Source components: UNKNOWN OR OTHER.
Source record 11022027 at NHTSANHTSA communication ID: 11017445
NHTSA source summary · Original PDF not reviewed by Recallfolio
ACTUATOR - A/C AND HEATER
Source components: UNKNOWN OR OTHER.
Source record 11017445 at NHTSANHTSA communication ID: 11017435
NHTSA source summary · Original PDF not reviewed by Recallfolio
ACTUATOR - A/C AND HEATER
Source components: UNKNOWN OR OTHER.
Source record 11017435 at NHTSANHTSA communication ID: 10248517
NHTSA source summary · Original PDF not reviewed by Recallfolio
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
Source components: EQUIPMENT.
Source record 10248517 at NHTSANHTSA communication ID: 10244356
NHTSA source summary · Original PDF not reviewed by Recallfolio
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
Source components: SUSPENSION.
Source record 10244356 at NHTSANHTSA communication ID: 10248509
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
Source components: ELECTRICAL SYSTEM.
Source record 10248509 at NHTSANHTSA communication ID: 10244348
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
Source components: ELECTRICAL SYSTEM:WIRING.
Source record 10244348 at NHTSANHTSA communication ID: 10243209
NHTSA source summary · Original PDF not reviewed by Recallfolio
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10243209 at NHTSANHTSA communication ID: 10243208
NHTSA source summary · Original PDF not reviewed by Recallfolio
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10243208 at NHTSANHTSA communication ID: 10242717
NHTSA source summary · Original PDF not reviewed by Recallfolio
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10242717 at NHTSANHTSA communication ID: 10239957
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Quality When Mixed With Engine Coolant
Source components: ENGINE AND ENGINE COOLING.
Source record 10239957 at NHTSANHTSA communication ID: 10236933
NHTSA source summary · Original PDF not reviewed by Recallfolio
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
Source record 10236933 at NHTSANHTSA communication ID: 10234379
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
Source components: ENGINE AND ENGINE COOLING.
Source record 10234379 at NHTSANHTSA communication ID: 10247905
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
Source components: BACK OVER PREVENTION.
Source record 10247905 at NHTSANHTSA communication ID: 10234378
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
Source components: ENGINE AND ENGINE COOLING.
Source record 10234378 at NHTSANHTSA communication ID: 10247995
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
Source components: STRUCTURE.
Source record 10247995 at NHTSANHTSA communication ID: 10234468
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
Source components: STRUCTURE.
Source record 10234468 at NHTSANHTSA communication ID: 10231753
NHTSA source summary · Original PDF not reviewed by Recallfolio
Emissions recal U67 Catalytic Converter Efficiency
Source components: POWER TRAIN.
Source record 10231753 at NHTSANHTSA communication ID: 10229810
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
Source components: STRUCTURE.
Source record 10229810 at NHTSANHTSA communication ID: 10230438
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the above-involved vehicles may exceed NOx (Oxides of Nitrogen) emission level standards due to loss of catalytic converter efficiency
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE · UNKNOWN OR OTHER.
Source record 10230438 at NHTSANHTSA communication ID: 10229572
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
Source components: STRUCTURE.
Source record 10229572 at NHTSANHTSA communication ID: 10225424
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
Source components: STRUCTURE.
Source record 10225424 at NHTSANHTSA communication ID: 10225287
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
Source components: STRUCTURE · STRUCTURE:INTERIOR PANELS:DOOR · UNKNOWN OR OTHER.
Source record 10225287 at NHTSANHTSA communication ID: 10221375
NHTSA source summary · Original PDF not reviewed by Recallfolio
Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - Feb 28, 2019 VF. - Only use R8453637A$ or R8599680A$ for March 1, 2019 and later VF as they have the revised park system. - R8453637A$ and R8599680A$ are physically and functionally equivalent. Installing a R8453637A$ or R8599680A$ in a 2014 - Feb 28, 2019 VF will result in a core with the original park system being returned. Mopar can no longer convert 62TE core with the original park system to the March 1, 2019 and later version. Continued mis-usage will exacerbate the existing core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when
Source components: POWER TRAIN.
Source record 10221375 at NHTSANHTSA communication ID: 10227969
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold For concerns of V8 oil filter leaks on 22MY and up vehicles: 1. Clean the area and use oil dye to know the exact location of the leak with black/UV light. 2. Removal torque (force needed to loosen the filter) 3. If the source of the leak cannot be identified, please contact FCA Redacted Content to FasTrak parts back for analysis. If no response in 15 minutes, proceed with repair and email pictures of the following: A) Oil filter from the bottom to know if it has a "Factory Installed" filter. B) Leak. C) Damage in filter (if any) D) Gasket. E) Block or Oil Filter Adapter(OFA) or Engine Oil Cooler(EOC) sealing surface.
Source components: SEATS.
Source record 10227969 at NHTSANHTSA communication ID: 10228020
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · UNKNOWN OR OTHER.
Source record 10228020 at NHTSANHTSA communication ID: 10227983
NHTSA source summary · Original PDF not reviewed by Recallfolio
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
Source record 10227983 at NHTSANHTSA communication ID: 10228989
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
Source components: FUEL SYSTEM, OTHER:FUEL FILTER.
Source record 10228989 at NHTSANHTSA communication ID: 10223028
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
Source components: FUEL SYSTEM, OTHER:FUEL FILTER.
Source record 10223028 at NHTSANHTSA communication ID: 10220645
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
Source components: FUEL SYSTEM, OTHER:FUEL FILTER.
Source record 10220645 at NHTSANHTSA communication ID: 10228975
NHTSA source summary · Original PDF not reviewed by Recallfolio
Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.
Source components: PARKING BRAKE · POWER TRAIN · STRUCTURE.
Source record 10228975 at NHTSANHTSA communication ID: 10223014
NHTSA source summary · Original PDF not reviewed by Recallfolio
Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.
Source components: PARKING BRAKE · POWER TRAIN · STRUCTURE.
Source record 10223014 at NHTSANHTSA communication ID: 10220631
NHTSA source summary · Original PDF not reviewed by Recallfolio
Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.
Source components: PARKING BRAKE · POWER TRAIN · STRUCTURE.
Source record 10220631 at NHTSANHTSA communication ID: 10212234
NHTSA source summary · Original PDF not reviewed by Recallfolio
Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.
Source components: PARKING BRAKE · POWER TRAIN · STRUCTURE.
Source record 10212234 at NHTSANHTSA communication ID: 10230180
NHTSA source summary · Original PDF not reviewed by Recallfolio
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
Source components: ENGINE AND ENGINE COOLING.
Source record 10230180 at NHTSANHTSA communication ID: 10221594
NHTSA source summary · Original PDF not reviewed by Recallfolio
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
Source components: ENGINE AND ENGINE COOLING.
Source record 10221594 at NHTSANHTSA communication ID: 10221231
NHTSA source summary · Original PDF not reviewed by Recallfolio
PLATE, TORQUE CONVERTER DRIVE For 3.6L with 62TE NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE & MUST BE REPLACED & PROPERLY TORQUED TO 105NM Replace the eight bolts (8) 06503465 drive plate to crank shaft and the four TC bolts 06504383 as they have sealants Vehicle miles < 30K: Mandatory replacement of transmission and driveplate Vehicle miles > 30K: Replace driveplate only (shot peened)
Source components: POWER TRAIN.
Source record 10221231 at NHTSANHTSA communication ID: 10212513
NHTSA source summary · Original PDF not reviewed by Recallfolio
PLATE, TORQUE CONVERTER DRIVE For 3.6L with 62TE NOTE: FOR ALL PROMASTER VF 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS Part Number 06511385A$ ARE ONE TIME USEAGE & MUST BE REPLACED & PROPERLY TORQUED TO 105NM Replace the eight bolts 8 06503465 drive plate to crank shaft and the four TC bolts 06504383 as they have sealants Vehicle miles < 30K: Mandatory replacement of transmission and driveplate Vehicle miles > 30K: Replace driveplate only shot peened
Source components: EQUIPMENT · POWER TRAIN.
Source record 10212513 at NHTSANHTSA communication ID: 10221150
NHTSA source summary · Original PDF not reviewed by Recallfolio
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
Source components: POWER TRAIN.
Source record 10221150 at NHTSANHTSA communication ID: 10221192
NHTSA source summary · Original PDF not reviewed by Recallfolio
Steering System Inspection After a Collision This bulletin documents the FCA US LLC position regarding conditions under which replacement or repair of steering system components are required.
Source components: EQUIPMENT ADAPTIVE/MOBILITY:VEHICLE CONTROLS:STEERING · STEERING.
Source record 10221192 at NHTSANHTSA communication ID: 10221098
NHTSA source summary · Original PDF not reviewed by Recallfolio
Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.
Source components: PARKING BRAKE · POWER TRAIN · STRUCTURE.
Source record 10221098 at NHTSANHTSA communication ID: 10221097
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
Source components: POWER TRAIN.
Source record 10221097 at NHTSANHTSA communication ID: 10193951
NHTSA source summary · Original PDF not reviewed by Recallfolio
Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.
Source components: PARKING BRAKE · POWER TRAIN · STRUCTURE.
Source record 10193951 at NHTSANHTSA communication ID: 10221123
NHTSA source summary · Original PDF not reviewed by Recallfolio
62TE 6-Speed Transmission Cracked Torque Converter (TC) Piston Repair Index, To Aid In Diagnosis And Repair
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
Source record 10221123 at NHTSANHTSA communication ID: 10193976
NHTSA source summary · Original PDF not reviewed by Recallfolio
62TE 6-Speed Transmission Cracked Torque Converter (TC) Piston Repair Index, To Aid In Diagnosis And Repair
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
Source record 10193976 at NHTSANHTSA communication ID: 10190589
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
Source components: ENGINE AND ENGINE COOLING.
Source record 10190589 at NHTSANHTSA communication ID: 10187662
NHTSA source summary · Original PDF not reviewed by Recallfolio
Warranty Bulletin D-20-16 (X84) Active Head Restraint - Select 2012-2018 Dodge Journey (JC) and 2012-2014 Dodge Avenger/Chrysler 200 (JS) (Rev. B)
Source components: SEATS:FRONT ASSEMBLY:HEAD RESTRAINT.
Source record 10187662 at NHTSANHTSA communication ID: 10224063
NHTSA source summary · Original PDF not reviewed by Recallfolio
Warranty Bulletin D-20-16 (X84) Active Head Restraint - Select 2012-2018 Dodge Journey (JC) and 2012-2014 Dodge Avenger/Chrysler 200 (JS) (Rev. A)
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · SEATS.
Source record 10224063 at NHTSANHTSA communication ID: 10184741
NHTSA source summary · Original PDF not reviewed by Recallfolio
Warranty Bulletin D-20-16 (X84) Active Head Restraint - Select 2012-2018 Dodge Journey (JC) and 2012-2014 Dodge Avenger/Chrysler 200 (JS) (Rev. A)
Source components: SEATS:MID/REAR ASSEMBLY:HEAD RESTRAINT.
Source record 10184741 at NHTSANHTSA communication ID: 10184441
NHTSA source summary · Original PDF not reviewed by Recallfolio
Warranty Bulletin D-20-16 (X84) Active Head Restraint - Select 2012-2018 Dodge Journey (JC) and 2012-2014 Dodge Avenger/Chrysler 200 (JS) (Rev. A)
Source components: SEATS:FRONT ASSEMBLY:HEAD RESTRAINT · SEATS:MID/REAR ASSEMBLY:HEAD RESTRAINT.
Source record 10184441 at NHTSANHTSA communication ID: 10224057
NHTSA source summary · Original PDF not reviewed by Recallfolio
Warranty Bulletin D-20-16 (X84) Active Head Restraint - Select 2010-2018 Dodge Journey (JC) and 2010-2014 Dodge Avenger/Chrysler 200 (JS)
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · SEATS.
Source record 10224057 at NHTSANHTSA communication ID: 10184735
NHTSA source summary · Original PDF not reviewed by Recallfolio
Warranty Bulletin D-20-16 (X84) Active Head Restraint - Select 2010-2018 Dodge Journey (JC) and 2010-2014 Dodge Avenger/Chrysler 200 (JS)
Source components: SEATS:MID/REAR ASSEMBLY:HEAD RESTRAINT.
Source record 10184735 at NHTSANHTSA communication ID: 10184435
NHTSA source summary · Original PDF not reviewed by Recallfolio
Warranty Bulletin D-20-16 (X84) Active Head Restraint - Select 2010-2018 Dodge Journey (JC) and 2010-2014 Dodge Avenger/Chrysler 200 (JS)
Source components: EQUIPMENT · SEATS:FRONT ASSEMBLY:HEAD RESTRAINT · SEATS:MID/REAR ASSEMBLY:HEAD RESTRAINT.
Source record 10184435 at NHTSANHTSA communication ID: 10183098
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
Source components: STRUCTURE.
Source record 10183098 at NHTSANHTSA communication ID: 10221831
NHTSA source summary · Original PDF not reviewed by Recallfolio
(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:TRANSMISSION CASE/HOUSING.
Source record 10221831 at NHTSANHTSA communication ID: 10180221
NHTSA source summary · Original PDF not reviewed by Recallfolio
(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
Source components: ELECTRICAL SYSTEM · ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10180221 at NHTSANHTSA communication ID: 10223512
NHTSA source summary · Original PDF not reviewed by Recallfolio
THROTTLE BODY For clarification, only use 68414676A$ on 2010 & earlier vehicles as supply is limited.
Source components: FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:THROTTLEBODY/MANIFOLD.
Source record 10223512 at NHTSANHTSA communication ID: 10177457
NHTSA source summary · Original PDF not reviewed by Recallfolio
THROTTLE BODY For clarification, only use 68414676A$ on 2010 & earlier vehicles as supply is limited.
Source components: ENGINE.
Source record 10177457 at NHTSANHTSA communication ID: 10176476
NHTSA source summary · Original PDF not reviewed by Recallfolio
Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.
Source components: ENGINE · POWER TRAIN.
Source record 10176476 at NHTSANHTSA communication ID: 10175743
NHTSA source summary · Original PDF not reviewed by Recallfolio
Disinfectant Solution Recommended for COVID-19
Source components: EQUIPMENT · STRUCTURE.
Source record 10175743 at NHTSANHTSA communication ID: 10175735
NHTSA source summary · Original PDF not reviewed by Recallfolio
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10175735 at NHTSANHTSA communication ID: 10175733
NHTSA source summary · Original PDF not reviewed by Recallfolio
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
Source components: FUEL SYSTEM, GASOLINE.
Source record 10175733 at NHTSANHTSA communication ID: 10175501
NHTSA source summary · Original PDF not reviewed by Recallfolio
Speed Control Operates Intermittently
Source components: VEHICLE SPEED CONTROL.
Source record 10175501 at NHTSANHTSA communication ID: 10175088
NHTSA source summary · Original PDF not reviewed by Recallfolio
Speed Control Operates Intermittently
Source components: VEHICLE SPEED CONTROL.
Source record 10175088 at NHTSANHTSA communication ID: 10174168
NHTSA source summary · Original PDF not reviewed by Recallfolio
Speed Control Operates Intermittently
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · EQUIPMENT:ELECTRICAL.
Source record 10174168 at NHTSANHTSA communication ID: 10170408
NHTSA source summary · Original PDF not reviewed by Recallfolio
No Start After Powertrain Control Module (PCM) Replacement and/or Reprogramming
Source components: ELECTRICAL SYSTEM.
Source record 10170408 at NHTSANHTSA communication ID: 10170314
NHTSA source summary · Original PDF not reviewed by Recallfolio
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
Source components: SUSPENSION.
Source record 10170314 at NHTSANHTSA communication ID: 10220101
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
Source components: STRUCTURE.
Source record 10220101 at NHTSANHTSA communication ID: 10220099
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
Source components: STRUCTURE.
Source record 10220099 at NHTSANHTSA communication ID: 10220098
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
Source components: VISIBILITY.
Source record 10220098 at NHTSANHTSA communication ID: 10220097
NHTSA source summary · Original PDF not reviewed by Recallfolio
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
Source components: EQUIPMENT · STRUCTURE.
Source record 10220097 at NHTSANHTSA communication ID: 10169249
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
Source components: EQUIPMENT · STRUCTURE.
Source record 10169249 at NHTSANHTSA communication ID: 10169247
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
Source components: EQUIPMENT.
Source record 10169247 at NHTSANHTSA communication ID: 10169246
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
Source components: VISIBILITY.
Source record 10169246 at NHTSANHTSA communication ID: 10169245
NHTSA source summary · Original PDF not reviewed by Recallfolio
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
Source components: STRUCTURE.
Source record 10169245 at NHTSANHTSA communication ID: 10166537
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
Source components: EQUIPMENT · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10166537 at NHTSANHTSA communication ID: 10162466
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Filter Adapter If replacing Oil Filter Adapter due to oil leak, please be aware a seal kit is available for repair. If replacing due to missing Spring Loaded Check Valve, a replacement spring and check valve are now available through MOPAR.
Source components: ENGINE · EQUIPMENT.
Source record 10162466 at NHTSANHTSA communication ID: 10224894
NHTSA source summary · Original PDF not reviewed by Recallfolio
Cam Phasers, Oil Control Valve For Malfunction Indicator Light (MIL) issues related to 2012-2017 3.6L Pentastar engines, please note that there is a new diagnostic procedure available in DealerCONNECT for P-codes in relationship to cam phasers. Please use this new information for trouble shooting of cam phasers and oil control valves for MIL on issues.
Source components: ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION · EXTERIOR LIGHTING.
Source record 10224894 at NHTSANHTSA communication ID: 10224887
NHTSA source summary · Original PDF not reviewed by Recallfolio
RES / RHA / REB Radios That Support Bluetooth and Hands-Free 1. For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands; DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Hands Free Module (and associated components) are the systems responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis. Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Source components: EQUIPMENT:ELECTRICAL:INFOTAINMENT · EQUIPMENT:ELECTRICAL:INFOTAINMENT:BLUETOOTH/WIFI.
Source record 10224887 at NHTSANHTSA communication ID: 10224693
NHTSA source summary · Original PDF not reviewed by Recallfolio
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
Source components: EQUIPMENT.
Source record 10224693 at NHTSANHTSA communication ID: 10219830
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
Source components: VISIBILITY:WINDSHIELD WIPER/WASHER.
Source record 10219830 at NHTSANHTSA communication ID: 10217521
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
Source components: FUEL SYSTEM, GASOLINE.
Source record 10217521 at NHTSANHTSA communication ID: 10139989
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
Source components: ENGINE AND ENGINE COOLING.
Source record 10139989 at NHTSANHTSA communication ID: 10217510
NHTSA source summary · Original PDF not reviewed by Recallfolio
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
Source components: SEAT BELTS.
Source record 10217510 at NHTSANHTSA communication ID: 10139978
NHTSA source summary · Original PDF not reviewed by Recallfolio
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
Source components: SEAT BELTS.
Source record 10139978 at NHTSANHTSA communication ID: 10217517
NHTSA source summary · Original PDF not reviewed by Recallfolio
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
Source components: SEAT BELTS.
Source record 10217517 at NHTSANHTSA communication ID: 10139985
NHTSA source summary · Original PDF not reviewed by Recallfolio
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
Source components: SEAT BELTS.
Source record 10139985 at NHTSANHTSA communication ID: 10121846
NHTSA source summary · Original PDF not reviewed by Recallfolio
RES / RHA / REB Radios That Supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) are the systems responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10121846 at NHTSANHTSA communication ID: 10223855
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
Source components: VISIBILITY/WIPER.
Source record 10223855 at NHTSANHTSA communication ID: 10223817
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set: U0140 - Lost Communication With Body Control Module. P0441 - EVAP Purge System Performance. P0420 - Catalyst Efficiency (Bank 1). P0430 - Catalyst Efficiency (Bank 2). P0133 - O2 Sensor 1/1 Slow Response. P0153 - O2 Sensor 2/1 Slow Response. P0300 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. P113D - O2 Sensor 1/1 Slow Response (High Frequency). P113E - O2 Sensor 2/1 Slow Response (High Frequency). P0108 - Manifold Absolute Pressure Sensor Circuit High. P0606 - Internal Control Processor. P0204 - Fuel Injector 4 Circuit/Open.In addition, the customer may notice the following conditions: 1 - 2 upshift clunk or bump. 4 - 5 upshift clunk or bump. 5 - 6 upshift clunk or bump. 6 - 5 downshift clunk or bump. 6 - 4 downshift clunk or bump. RPM fluctuating or jerking feeling while operating in cruise control. Condition is more noticeable when the vehicle is going up and down grades. A less than desired idle speed after performing a hard braking maneuver.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
Source record 10223817 at NHTSANHTSA communication ID: 10121739
NHTSA source summary · Original PDF not reviewed by Recallfolio
VECI Label The Authorized Modification Label is no longer required to be filled out and attached to the vehicle when flashing controllers in service. This includes 2013 and older TSB's where it is stated in the TSB to *Type the necessary information on the *Authorized Modification Label* and attach it near the VECI label*.
Source components: EQUIPMENT:OTHER:LABELS.
Source record 10121739 at NHTSANHTSA communication ID: 10130081
NHTSA source summary · Original PDF not reviewed by Recallfolio
Return: Wiring Assy - Engine You have been identified as either having stock, or have stock in transit to your dealership. Please return stock packaged before 2016/07/31 (31 July, 2016)of follow ing part numbers:68176457AF, 68176459AF. Please return suspect parts back to your facing depot using Return Code 02, before 13 September, 2016.
Source components: ELECTRICAL SYSTEM:WIRING.
Source record 10130081 at NHTSANHTSA communication ID: 10130080
NHTSA source summary · Original PDF not reviewed by Recallfolio
05182535AD - Lamp Assy ?Tail Light LT You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 05182535AD . See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
Source components: EQUIPMENT · EXTERIOR LIGHTING.
Source record 10130080 at NHTSANHTSA communication ID: 10130079
NHTSA source summary · Original PDF not reviewed by Recallfolio
Inspect and Return: Trim Cover Assy - A-Pillar Rt/Lt You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part numbers: 1ZA04DX9AE, 1ZA05DX9AE. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
Source components: EQUIPMENT.
Source record 10130079 at NHTSANHTSA communication ID: 10129047
NHTSA source summary · Original PDF not reviewed by Recallfolio
Warranty Operations Newsletter Updates from Warranty Operations
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10129047 at NHTSANHTSA communication ID: 10129045
NHTSA source summary · Original PDF not reviewed by Recallfolio
CBXDP361AA Return: Spacer Kit - Visor You have been identified as either having stock, or have stock in transit to your dealership. Please return stock of part number CBXDP361AA. Replacement part number is CBXDP361AB w hich is in stock and available for order. Please return suspect parts back to your facing depot using Return Code 02, before 16 September, 2016.
Source components: EQUIPMENT.
Source record 10129045 at NHTSANHTSA communication ID: 10129044
NHTSA source summary · Original PDF not reviewed by Recallfolio
1NT30XDVAC - Inspect and Return: Panel - Instrument Panel You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 1N T30XDVAC. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL.
Source record 10129044 at NHTSANHTSA communication ID: 10129043
NHTSA source summary · Original PDF not reviewed by Recallfolio
Inspect and Return: Solenoid Module - Transmission You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of follow ing part numbers:52120000AA, 52119435AF, 05078709AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
Source components: ELECTRICAL SYSTEM.
Source record 10129043 at NHTSANHTSA communication ID: 10129042
NHTSA source summary · Original PDF not reviewed by Recallfolio
Return: Lamp Assy - CHMSL& Cargo Light You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of follow ing part numbers:55372082AE, 55372082AD, 55372082AC, 55372082AB, 55372082AA. Replacement part number is 55372082AF w hich is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10129042 at NHTSA