The manufacturer’s record · Page 8 of 13
Original record summaries, dates and identifiers for this model-year. Records 701–800 of 1,271, ordered newest first. Dated records on this page: Jul 16, 2019–Jan 28, 2020.
Back to 2018 Chevrolet TAHOE problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10171896
NHTSA source summary · Original PDF not reviewed by Recallfolio
This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away to correct a crank/No Start condition.
Source components: ENGINE.
Source record 10171896 at NHTSANHTSA communication ID: 10172293
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
Source components: EQUIPMENT · WHEELS.
Source record 10172293 at NHTSANHTSA communication ID: 10171307
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates customers may comment on poor remote keyless entry (RKE) range (less than 20 feet.) Some customers may comment that the RKE fob must be held next to the driver door handle before the doors will unlock when passively attempting to unlock the door. The Radio Antenna Amplifier may be causing the range issue.
Source components: ELECTRICAL SYSTEM.
Source record 10171307 at NHTSANHTSA communication ID: 10171875
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
Source record 10171875 at NHTSANHTSA communication ID: 10171885
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to install an oil cooler line fitting seal, including applying medium strength threadlocker (blue) to the retaining bolt to stop transmission fluid leaking from the transmission oil cooler line retaining bolt passage.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · FUEL SYSTEM, GASOLINE · POWER TRAIN.
Source record 10171885 at NHTSANHTSA communication ID: 10172285
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
Source components: EQUIPMENT.
Source record 10172285 at NHTSANHTSA communication ID: 10171888
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10171888 at NHTSANHTSA communication ID: 10171290
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians are referred to Torque Converter Diagnosis in SI.
Source components: POWER TRAIN.
Source record 10171290 at NHTSANHTSA communication ID: 10171894
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of Phone Charging Cycles On and Off When Connected to the Single Port USB Hub.
Source components: ELECTRICAL SYSTEM.
Source record 10171894 at NHTSANHTSA communication ID: 10171280
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
Source components: ENGINE AND ENGINE COOLING.
Source record 10171280 at NHTSANHTSA communication ID: 10171265
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.
Source components: ENGINE AND ENGINE COOLING.
Source record 10171265 at NHTSANHTSA communication ID: 10171264
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer additional information on checking for the engne crankcase being overfull on oil causing an engine vibration concern. The technician is advised to inspect for contaminnants and adjust the engine oil level as needed.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
Source record 10171264 at NHTSANHTSA communication ID: 10171259
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015?0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that "mating" surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped
Source components: ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10171259 at NHTSANHTSA communication ID: 10171878
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM.
Source record 10171878 at NHTSANHTSA communication ID: 10170483
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).
Source components: TRAILER HITCHES.
Source record 10170483 at NHTSANHTSA communication ID: 10170498
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
Source components: EQUIPMENT.
Source record 10170498 at NHTSANHTSA communication ID: 10170424
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.
Source components: SERVICE BRAKES.
Source record 10170424 at NHTSANHTSA communication ID: 10169357
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10169357 at NHTSANHTSA communication ID: 10169271
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM for metal.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
Source record 10169271 at NHTSANHTSA communication ID: 10168978
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
Source components: POWER TRAIN.
Source record 10168978 at NHTSANHTSA communication ID: 10168975
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
Source components: ENGINE AND ENGINE COOLING.
Source record 10168975 at NHTSANHTSA communication ID: 10169270
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to add PET tape to the brake cables if the cause of the customers concern.
Source components: SERVICE BRAKES.
Source record 10169270 at NHTSANHTSA communication ID: 10169340
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE.
Source record 10169340 at NHTSANHTSA communication ID: 10169315
NHTSA source summary · Original PDF not reviewed by Recallfolio
This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away.
Source components: ENGINE.
Source record 10169315 at NHTSANHTSA communication ID: 10169309
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides information for rebuilding fuel injectors in the event of an underhood fuel odor and/or extended cranking condition.
Source components: ENGINE · FUEL SYSTEM, GASOLINE.
Source record 10169309 at NHTSANHTSA communication ID: 10169298
NHTSA source summary · Original PDF not reviewed by Recallfolio
Information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares.
Source components: POWER TRAIN.
Source record 10169298 at NHTSANHTSA communication ID: 10169356
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · TIRES · WHEELS.
Source record 10169356 at NHTSANHTSA communication ID: 10169354
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · EXTERIOR LIGHTING.
Source record 10169354 at NHTSANHTSA communication ID: 10168965
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that show a "Take Steering" message on the Driver Information Center along with a warning chime/alert. Dealer should be advised the purpose of the message is to alert the driver that the Lane Keep Assist system has not detected active steering input from the driver (hands off the steering wheel).
Source components: LANE DEPARTURE.
Source record 10168965 at NHTSANHTSA communication ID: 10168964
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a normal DIC message after learning keys/fobs which indicates the drivers memory position.
Source components: EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
Source record 10168964 at NHTSANHTSA communication ID: 10168963
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the new 2015 - 2017 Tahoe Police Package Vehicle and Special Service Vehicle have four relay controlled circuits which can be utilized when installing special first responder equipment. Please reference the latest version of General Motors Upfitter Integration Bulletin 118 for additional information on these circuits.
Source components: ELECTRICAL SYSTEM.
Source record 10168963 at NHTSANHTSA communication ID: 10168960
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
Source components: SERVICE BRAKES, AIR:ANTILOCK · WHEELS.
Source record 10168960 at NHTSANHTSA communication ID: 10168958
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.
Source components: ENGINE AND ENGINE COOLING.
Source record 10168958 at NHTSANHTSA communication ID: 10168956
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
Source components: ELECTRICAL SYSTEM.
Source record 10168956 at NHTSANHTSA communication ID: 10168212
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
Source components: POWER TRAIN.
Source record 10168212 at NHTSANHTSA communication ID: 10167466
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
Source components: ELECTRICAL SYSTEM.
Source record 10167466 at NHTSANHTSA communication ID: 10167465
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates if the sunroof, rear sliding window, and/or wireless charging are found to be inoperative due to the F2DL and/or the F8DL fuse(s) being open. Inspect the center console harness area at the hinge pivot point for chaffed circuits.
Source components: ELECTRICAL SYSTEM · VISIBILITY.
Source record 10167465 at NHTSANHTSA communication ID: 10167463
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates that an inoperative third row folding seat back may not fold down or up. This information advises dealers on how the seat functions and also a common area where an open circuit may be found between the third row seat module and the seat position sensor. It provides repair instructions if a concern is found with the circuits between the third row folding seat module and the seat back position sensor, as well as advising the dealer to look for bent/damaged seat recline mechanisms.
Source components: ELECTRICAL SYSTEM.
Source record 10167463 at NHTSANHTSA communication ID: 10167462
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.
Source components: ELECTRICAL SYSTEM.
Source record 10167462 at NHTSANHTSA communication ID: 10167461
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a detent / click with a feel of increased resistance when the accelerator pedal is about ¾ of the way. The new accelerator pedal design has a built-in detent position near the last 1/4 of pedal travel. Dealer should communicate to the customer this is a normal operating characteristic of the vehicle and no repair attempts should be performed.
Source components: VEHICLE SPEED CONTROL:ACCELERATOR PEDAL.
Source record 10167461 at NHTSANHTSA communication ID: 10167460
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.
Source components: LANE DEPARTURE.
Source record 10167460 at NHTSANHTSA communication ID: 10167459
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps needed to diagnose and repair vehicles that may have a rattle noise from the dash. Technician will need to inspect for the rear heater pipes contacting the passenger side exhaust manifold. If the rear heater pipe is found to be contacting the exhaust manifold, reposition the heater pipe so it no longer makes contact.
Source components: ENGINE AND ENGINE COOLING.
Source record 10167459 at NHTSANHTSA communication ID: 10167455
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
Source components: EQUIPMENT.
Source record 10167455 at NHTSANHTSA communication ID: 10168207
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10168207 at NHTSANHTSA communication ID: 10167442
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates if the liftglass will not open using keyless entry to verify Valet Mode is not enabled.
Source components: ELECTRICAL SYSTEM.
Source record 10167442 at NHTSANHTSA communication ID: 10167439
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how the radio display gets the air ambient temperature. On 1500 series trucks and all sport utility vehicle with regular production option code IO3 radio the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio. On 1500 series trucks and all sport utility vehicle with regular production option code IO4, IO5, or IO6 the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface. On 2500/3500 series trucks production option code IO3 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio. On 2500/3500 series trucks production option code IO4, IO5, or IO6 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface.
Source components: ELECTRICAL SYSTEM.
Source record 10167439 at NHTSANHTSA communication ID: 10168175
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
Source components: POWER TRAIN.
Source record 10168175 at NHTSANHTSA communication ID: 10167437
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
Source components: ENGINE.
Source record 10167437 at NHTSANHTSA communication ID: 10168185
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10168185 at NHTSANHTSA communication ID: 10167479
NHTSA source summary · Original PDF not reviewed by Recallfolio
N182202780 01 - Special Coverage. Certain Vehicles may have a condition where customers may experience increased brake pedal effort, hardbrake pedal, and/or potentially increased stopping distance. The condition is more prevalent at low speed when softly applyingthe brakes. The engine mounted mechanical vacuum pump outputmay decrease over time decreasing the amount of vacuum/power brake assist. Failure to follow recommended oil change intervalscould contribute to this condition. The Driver?s Information Center, (DIC) ?Service brake assist? alert will activate 2-5minutes after the vacuum level drops, and a Diagnostic Trouble Code, (DTC) will also be set. Even where this condition occurs,the hydraulic brake system remains functional but may require additionalpedal force. Please be aware that even if the vehicle exhibits this condition, it meets all federal motor vehicle safety standards forbrake performance. Dealers are to replace the vacuum pump and vacuum pump belt. The repairs will be made at no charge to the customer.
Source components: ENGINE AND ENGINE COOLING · SERVICE BRAKES, AIR:CONTROLS:FOOT CONTROL/VALVE.
Source record 10167479 at NHTSANHTSA communication ID: 10167434
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
Source components: ELECTRICAL SYSTEM.
Source record 10167434 at NHTSANHTSA communication ID: 10168208
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on key code security and information on GM key code look up applications.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10168208 at NHTSANHTSA communication ID: 10168205
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
Source components: ENGINE AND ENGINE COOLING.
Source record 10168205 at NHTSANHTSA communication ID: 10168214
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure to reprogram more than 8 keys for the PPV.
Source components: UNKNOWN OR OTHER.
Source record 10168214 at NHTSANHTSA communication ID: 10167426
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians are referred to Torque Converter Diagnosis in SI.
Source components: ELECTRICAL SYSTEM.
Source record 10167426 at NHTSANHTSA communication ID: 10167425
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert".
Source components: FORWARD COLLISION AVOIDANCE.
Source record 10167425 at NHTSANHTSA communication ID: 10168204
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10168204 at NHTSANHTSA communication ID: 10168188
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10168188 at NHTSANHTSA communication ID: 10165920
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with erratic or hesitation when opening and closing the power liftgate. There may be a diagnostic trouble code B153A set in the power liftgate module. This concern could occur if the left liftgate actuator is internally coming apart. The actuator will need to be replaced however care must be taken when removing the actuator from the vehicle. If the internal portion of the actuator had completely separated the end of the actuator could become a projectile when removed. Obtain a number 8 self-tapping screw that measures 1 ½ inches long. Fully open the liftgate and install the screw anywhere in a 30 millimeter space from the bottom of the smooth tube to secure the tubes. Continue with the liftgate actuator by following the liftgate power assist actuator procedure in service information.
Source components: STRUCTURE:BODY:HATCHBACK/LIFTGATE.
Source record 10165920 at NHTSANHTSA communication ID: 10165914
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have Diagnostic Trouble Code P06DD or no or low oil pressure. Technician will replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump. Inspect bearings for damage wear due to debris from oil pump.
Source components: ENGINE AND ENGINE COOLING.
Source record 10165914 at NHTSANHTSA communication ID: 10165905
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar. Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.
Source components: STRUCTURE.
Source record 10165905 at NHTSANHTSA communication ID: 10165904
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
Source components: ELECTRICAL SYSTEM.
Source record 10165904 at NHTSANHTSA communication ID: 10166659
NHTSA source summary · Original PDF not reviewed by Recallfolio
This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
Source components: ENGINE AND ENGINE COOLING.
Source record 10166659 at NHTSANHTSA communication ID: 10166243
NHTSA source summary · Original PDF not reviewed by Recallfolio
N182206730 01 - Customer Satisfaction Program - Certain vehicles equipped with special service package (RPO 5W4) and certain 2018 ? 2019 Chevrolet Tahoe vehicles equipped with police package (RPO 9C1) or special service package (RPO 5W4) may have a condition in which frequent, repeated brake applications at low speed or idle speeds can deplete available brake vacuum assist faster than vacuum can be replenished by the system, which can lead to increased brake pedal effort, hard brake pedal and potentially increased stopping distance.
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10166243 at NHTSANHTSA communication ID: 10166638
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
Source components: EQUIPMENT.
Source record 10166638 at NHTSANHTSA communication ID: 10166635
NHTSA source summary · Original PDF not reviewed by Recallfolio
This diagnostic tip provides information to the tech to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away.
Source components: ENGINE AND ENGINE COOLING.
Source record 10166635 at NHTSANHTSA communication ID: 10166640
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to measure vibration and install engine mounts to correct a Rough Idle in Drive concern.
Source components: ENGINE AND ENGINE COOLING.
Source record 10166640 at NHTSANHTSA communication ID: 10165877
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
Source components: ELECTRICAL SYSTEM.
Source record 10165877 at NHTSANHTSA communication ID: 10165874
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10165874 at NHTSANHTSA communication ID: 10165870
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.
Source components: ENGINE AND ENGINE COOLING.
Source record 10165870 at NHTSANHTSA communication ID: 10165868
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert".
Source components: FORWARD COLLISION AVOIDANCE.
Source record 10165868 at NHTSANHTSA communication ID: 10165865
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Starting with 2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded.
Source components: STEERING.
Source record 10165865 at NHTSANHTSA communication ID: 10165120
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of Phone Charging Cycles On and Off When Connected to the Single Port USB Hub.
Source components: EQUIPMENT.
Source record 10165120 at NHTSANHTSA communication ID: 10164789
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have Diagnostic Trouble Code P06DD or no or low oil pressure. Technician will replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump. Inspect bearings for damage wear due to debris from oil pump.
Source components: ENGINE AND ENGINE COOLING.
Source record 10164789 at NHTSANHTSA communication ID: 10165127
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961).
Source components: ELECTRICAL SYSTEM.
Source record 10165127 at NHTSANHTSA communication ID: 10165087
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
Source components: EQUIPMENT.
Source record 10165087 at NHTSANHTSA communication ID: 10165124
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
Source components: ENGINE AND ENGINE COOLING.
Source record 10165124 at NHTSANHTSA communication ID: 10165126
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC.
Source components: EQUIPMENT.
Source record 10165126 at NHTSANHTSA communication ID: 10165121
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
Source components: ENGINE AND ENGINE COOLING.
Source record 10165121 at NHTSANHTSA communication ID: 10165122
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
Source components: ENGINE AND ENGINE COOLING.
Source record 10165122 at NHTSANHTSA communication ID: 10165114
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on Mandatory VECI Label Replacement for (5W7) Performance Air Intake Kits.
Source components: EQUIPMENT.
Source record 10165114 at NHTSANHTSA communication ID: 10165440
NHTSA source summary · Original PDF not reviewed by Recallfolio
N182206730 - Customer Satisfaction Program. Certain vehicles equipped with special service package (RPO 5W4) and certain 2015 ? 2019 Chevrolet Tahoe vehicles equipped with police package (RPO 9C1) or special service package (RPO 5W4) may have a condition in which frequent, repeated brake applications at low speed or idle speeds can deplete available brake vacuum assist faster than vacuum can be replenished by the system, which can lead to increased brake pedal effort, hard brake pedal and potentially increased stopping distance. These vehicles utilize Hydraulic Brake Boost Assist to supply additional hydraulic pressure when the vacuum boost is not sufficient to achieve the driver?s intended brake force. Dealers will reprogram the Electronic Brake Control Module in these vehicles with a new calibration that will improve how the system utilizes the Hydraulic Brake Boost Assist function when vacuum assist is depleted.
Source components: SERVICE BRAKES, HYDRAULIC · SERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM.
Source record 10165440 at NHTSANHTSA communication ID: 10165123
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10165123 at NHTSANHTSA communication ID: 10164758
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer technician that the torque converters for the 10L80 and 10L90 10 speed transmission are on restriction through the Product Quality Center. Dealers are advised to contact the Product Quality Center if diagnostics has lead to replacement of the transmission torque converter.
Source components: POWER TRAIN.
Source record 10164758 at NHTSANHTSA communication ID: 10164757
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.
Source components: ELECTRICAL SYSTEM · STEERING · VISIBILITY.
Source record 10164757 at NHTSANHTSA communication ID: 10164756
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a Service Adaptive Cruise With DTC C018C SYM3A After Replacing K14 Distance Sensing Cruise Control Module and provides tips for completing all necessary steps and to contact TCSC if configuration does not complete correctly.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL.
Source record 10164756 at NHTSANHTSA communication ID: 10165104
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM for metal.
Source components: POWER TRAIN.
Source record 10165104 at NHTSANHTSA communication ID: 10164749
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
Source components: VISIBILITY.
Source record 10164749 at NHTSANHTSA communication ID: 10165097
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of add-on equipment inoperative, melted terminals on auxiliary relay, new auxiliary battery relay for Police Tahoe Vehicles.
Source components: ELECTRICAL SYSTEM.
Source record 10165097 at NHTSANHTSA communication ID: 10165079
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
Source components: STEERING.
Source record 10165079 at NHTSANHTSA communication ID: 10163690
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates AFM / DFM usage Information. providing additional information on the AFM and DFM systems
Source components: EQUIPMENT:ELECTRICAL.
Source record 10163690 at NHTSANHTSA communication ID: 10164113
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on Information on Head-Up Display (HUD) on Vehicles Model Year 2017 and Newer Has Rotational Feature that Allows for Adjusting of the Angle of the HUD Image.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10164113 at NHTSANHTSA communication ID: 10163686
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
Source components: EQUIPMENT.
Source record 10163686 at NHTSANHTSA communication ID: 10163684
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10163684 at NHTSANHTSA communication ID: 10163682
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer technician that the 10L90 and 10L80 transmissions part restriction has ended.
Source components: POWER TRAIN.
Source record 10163682 at NHTSANHTSA communication ID: 10163681
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and a message "Remote Learn Pending" will be displayed on the Driver Information Center. In the past to perform the new transmitter procedure only one previously learned transmitter was required but this is no longer the case. Now, two previously learned transmitters are required to be placed into the cup holder and then the new transmitter to be programmed placed in the transmitter pocket. If this new procedure is not followed, the "adding transmitters without Service Programming System" cannot be performed. The technician will be forced to add a transmitter using Service Programming System.
Source components: EQUIPMENT.
Source record 10163681 at NHTSANHTSA communication ID: 10163900
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides process information for the (GWM) and (WPC) parts return program.
Source components: EQUIPMENT.
Source record 10163900 at NHTSANHTSA communication ID: 10164119
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to add PET tape to the brake cables if the cause of the customers concern.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · PARKING BRAKE:CONVENTIONAL:MECHANICAL:LINKAGE AND CABLE.
Source record 10164119 at NHTSANHTSA communication ID: 10163902
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2016 model year to diagnostic tips and repair information to correct a customer concern of reduced acceleration at low speed and/or transmission slipping from a launch, DTC P0751 set.
Source components: POWER TRAIN.
Source record 10163902 at NHTSANHTSA communication ID: 10163665
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
Source components: VEHICLE SPEED CONTROL · WHEELS.
Source record 10163665 at NHTSA