2015 Chevrolet TAHOE Manufacturer communications & TSBs.Page 19
Original record summaries, dates and identifiers for this model-year. Records 1,801–1,900 of 2,575, ordered newest first. Dated records on this page: Mar 2, 2015–May 4, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
May 4, 2015Service Bulletin/Repair Instructions
PIT5405
NHTSA communication ID: 10114513
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for a reduced power message, steering assist, engine stall or the instrument panel, radio, and or Heater-Vent-Air Conditioning go blank with multiple diagnostic trouble codes. If any of the following diagnostic trouble codes U0073, U0078, U0029, U0028, U0415, U0140, U0126, U0121, U0101, U0100, C0544, U1510, U0073, B127B, B2605, B3600,C0800, U0428, and U0452 set in the vehicle. Check the body control module ground at the G218 location. The front dash insulator mat may be trapped between the ground eyelet and the body stud. Remove the round nut and eyelet and cut the front dash insulator mat away from the ground stud so it no longer interferes with the ground stud and reinstall the eyelet and ground nut.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a buffeting vibration and/or drone type noise, exhaust tone change, and/or body pressure booming. The concern may be most noticeable while the engine is operating in 4-cylinder Active Fuel Management mode in the 1,100-1,400 RPM range. If the noise is excessive it may excite the roof sheet metal and compound the issue, if this concern is found refer to the latest version of PIT5318. If the concern is qualified to be present during V4 mode operation, but is deemed to be normal by comparing to a like vehicle, then no further repairs should be made, as this is a normal characteristic. If the concern is qualified to be present during V4 mode operation, but is deemed excessive by comparing to a like vehicle then continue with the direction in the Preliminary Information. Vehicles equipped with the 6.2 liter engine and noise cancellation, the noise cancellation may not be working or working incorrectly this can be the cause of the issue. Technician should inspect for aftermarket audio components, objects blocking the microphones or speakers, Diagnostic Trouble Codes B0560, B1277, B127C, or B127D. By the technician pulling the fuse for the amplifier the noise cancellation will be disabled if the noise improves there may be an issue with the noise cancellation system. Technician should inspect the exhaust system also. Exhaust should be checked when it is hot and cold while the vehicle is in neutral, forward and reverse gear. Inspect the exhaust system for loose and/or missing fasteners, heat shields damaged, joints and/or couplings not properly seated, bracket and/or insulator mounting concerns, inadequate clearance to body and/or chassis components, improper alignment, disconnected and/or missing insulators, cracked, dry-rotted, and/or oil-soaked insulators, stretched, twisted, broken, torn, and/or collapsed insulators, and bent, twist
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for vehicles with the radio inoperative. The technician may find no communication with the radio and a diagnostic trouble code U0184 set in other modules. Technician is to call General Motors Technical Assistance Center for direction before attempting to diagnose or repair this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for a vehicle setting both a P2635 and P018B diagnostic trouble codes. The following steps may help to determine if this is caused by a fuel pressure sensor not reading the low end of the pressure range. Technician is to make sure the engine is cold and install the Multiple Diagnostic Interface along with Global Diagnostic System 2. Navigate to fuel system depressurize and at engine idle depressurize the fuel system. The fuel pressure sensor value should drop to 0 and the engine will stall. If a sensor is causing this concern the suspected sensor will not drop to 0 the engine will stall however the sensor will still read 30 to 40 pounds per square inch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information to correct a customer concern of wind noise generating from accessory roof cross rails.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET: SOME TRUCKS WILL EXPERIENCE A HIGH RESISTANCE IN WIRING HARNESS CONNECTORS CAUSING SERVICE AIR BAG MESSAGE TO BE DISPLAYED IN DRIVER INFORMATION CENTER (DIC). MODEL 2014 SILVERADO 1500, SIERRA 1500, 2015 SIERRA 2500/3500, YUKON, YUKON XL, SILVERADO 2500/3500, SUBURBAN, TAHOE. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/CADILLAC/GMC: INSTRUCTION INFORMATION REGARDING AN OIL LEAKAGE FROM ENGINE, AROUND LOCATION OF OIL FILTER OF OIL PAN. MODEL 2015 ESCALADE, SIERRA/SILVERADO 1500, SUBURBAN, YUKON, YUKON XL, TAHOE. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have various Heater-Vent-Air Conditioning issues. Technician should use Tis2Web to reprogram the Heater-Vent-Air Conditioning control module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information to correct a customer concern of Service Air Bag message displayed in Driver Information Center (DIC), and technician finding DTC B0014, B0021 or B001E set, with Symptom Code :04 or 0D.
Source components: AIR BAGS · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a Service 4WD message on the Driver Information Center when operated below 10 degrees Fahrenheit (-12 Celsius). Technician may find C0398 or C0326 stored in the Transfer Case Control Module. For vehicles with Regular Production Option Code NQH and NQ6 and only setting Diagnostic Trouble Codes C0398 or C0398 and C0326 the replacement of the actuator motor will correct the concern. Dealer will need to contact General Motors Product Quality Center for further assistance. For vehicles with Regular Production Option Code NQH and NQ6 with other transfer case Diagnostic Trouble Codes. If the vehicle had a Diagnostic Trouble Code C0398 in the transfer case control module stored with any other codes such as C0392, C0396, C0306 or other codes related to rotational position sensor or actuator position sensor it is likely that is causing a C0398 to set and replacement of the actuator will likely not repair the vehicle. For vehicles with Regular Production Option Code NP0 and only have a Diagnostic Trouble Code C0398 stored in the transfer case control module, the technician should insure the transfer case control module calibrations are up-to-date in Tis2Web.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information to correct a customer concern of Iitermittently key will not rotate in door or ignition lock cylinder.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an oily substance is found on the inside windshield surface and appears to be leaking from the rear view mirror area. Technician should inspect the moisture sensor for being the source of the leak, if found to be leaking, carefully remove the moisture sensor. Clean the glass surface and sensor bracket with an isopropanol alcohol wipe until the surfaces are clean, then re-install the moisture sensor.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair procedure information to correct a customer concern of Transport Mode On message displayed in Driver Information Center (DIC) and/or battery light is flashing.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that effective July 28, 2014, the Instrument Panel Cluster will be placed on restriction. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides radio programming information to correct customer concerns about no XM audio or time shift, radio lock-up, slow response, vertical line between clock and temperature, poor FM reception (Truck Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
14281 - CUSTOMER SATISFACTION PROGRAM. CERTAIN 2014-2015 MODEL YEAR CHEVROLET SILVERADO, SUBURBAN, AND TAHOE MODEL VEHICLES AND 2014-2015 MODEL YEAR GMC SIERRA AND YUKON MODEL VEHICLES EQUIPPED WITH A DEALER INSTALLED REAR ENTERTAINMENT SYSTEM MAY HAVE A CONDITION IN WHICH THE REAR SEAT ENTERTAINMENT SYSTEM IN VEHICLES WAS RELEASED AS A DEALER ACCESSORY BEFORE FINAL GENERAL MOTORS VALIDATION APPROVAL. VALIDATION APPROVAL AT GM REQUIRES VERY RIGOROUS TESTING PRIOR TO RELEASE, WHICH, IN MANY CASES, GOES BEYOND WHAT IS REQUIRED TO COMPLY WITH GOVERNMENTAL SAFETY STANDARDS. THESE VEHICLES, AS EQUIPPED, STILL MEETS ALL FEDERAL MOTOR VEHICLE SAFETY STANDARDS. DEALERS ARE TO REMOVE AND REPLACE THE HINGED SCREEN STYLE REAR SEAT ENTERTAINMENT SYSTEM, WITH A REVISED SYSTEM FEATURING AN INTEGRAL SCREEN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B124B sym 04 in the HMI module. Technician should check the USB port operations if no issue found it should be considered a false code and no components should be replaced. If the USB port is inoperative technician should follow published Service Information diagnosis for Auxiliary Audio Input Malfunction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are unable to access XM Weather. If the system responds by highlighting the XM Weather Icon but it does not enter the application technician should replace the Human Machine Interface module for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles with visible water leak or signs of water intrusion from the antenna base, red OnStar LED, unable to connect to OnStar, OnStar unable to locate the vehicle, OnStar has inaccurate global positioning system location, no global positioning system on the navigation radio display, and inaccurate global positioning system location on the navigation radio display. Technician may find Diagnostic Trouble Codes B2462-02, B2462-04, B2470-02, B2470-04, B125C-01, B125C-02, or B125C-04. Technician should replace the high efficiency antenna with the latest part number in the catalog.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides inspection and repair information to correct a customer concern of XM/Cellular Mobile Phone/OnStar Antenna looseness or damage, XM/Cellular/OnStar reception performance degraded, rattle/flutter/squeak noise, wind noise/whistle at highway speeds, water leak on headliner at sunvisor.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides radio programming information to correct customer concerns about no XM audio or time shift, radio lock-up, slow response, vertical line between clock and temperature, poor FM reception (truck only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides reprpgramming information to correct a customer concern of blank display, NAV screen audio content is unavailable via speech recognition, display screen is stuck on incoming call view after phone call finished, rear view camera display blank, USB Issues/Bluetooth/Favorite Bar/Voice, iPod unable to detect via USB, recognition concerns, XM speech recognition inoperative, traffic messages, clock display.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have the rear vision camera system displaying "Rear Park Assist Symbols Unavailable" and the steering grid lines displayed do not show. Dealer will need to communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp dimly illuminated while the engine is running. Technician will need to replace the Instrument Panel Cluster with the update part number.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a blank radio display. Technician may find a Diagnostic Trouble Code U150F stored in the Radio / Heater-Vent-Air Conditioning controls. Technician will verify if the correct display is installed. If the Diagnostic Trouble Code is current inspect the circuit form end to end.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Codes P0089, P127C, P127D, P0192, P0193, P228C, P228D, and P006C. Technician should follow published Service Information diagnostics for the Diagnostic Trouble Codes that are stored. If Service Information does not lead to a repair for the concern, the fuel rail pressure sensor should be replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure message. Technician may also find a Diagnostic Trouble Code P0521 in the Engine Control Module. Technician should follow all published Service Information diagnosis. When using a scan tool if the oil pressure is low but the oil pressure at the oil filter housing is correct, technician should inspect the Valve Lifter Oil Filter for debris/sludge that could be restricting oil flow to the oil pressure sensor. Technician should remove the Valve Lifter Oil Filter and clean it. If the Valve Lifter Oil Filter cannot be cleaned replace it.
NHTSA source summary · Original PDF not reviewed by Recallfolio
14395A - CUSTOMER SATISFACTION PROGRAM (REVISED LABOR TIME). ON SOME 2015 MODEL YEAR BUICK ENCORE, LACROSSE, REGAL, AND VERANO; CADILLAC ATS, CTS, ELR, ESCALADE, SRX AND XTS; CHEVROLET COLORADO, CORVETTE, CRUZE, EQUINOX, IMPALA, MALIBU, SILVERADO, SONIC, SPARK, SS, SUBURBAN, TAHOE, TRAX, AND VOLT; AND GMC CANYON, SIERRA, TERRAIN, AND YUKON VEHICLES, A PERFORMANCE ISSUE WITH THE ONSTAR® MODULE MIGHT IMPACT THE VEHICLE'S BATTERY LIFE. THIS CAN CAUSE A DEAD BATTERY IF THE VEHICLE IS NOT STARTED FOR APPROXIMATELY 4 DAYS. THIS CONDITION CAN OCCUR EVEN IF THE ONSTAR® SYSTEM IS NOT ACTIVE. DEALERS ARE TO REPLACE THE ONSTAR® MODULE. IF THE CUSTOMER DOES NOT HAVE AN ACTIVE ONSTAR® SUBSCRIPTION, THE ONSTAR® MODULE IS TO BE DEACTIVATED AFTER REPLACEMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the LCT1000 6 Speed Allison automatic transmission is on restriction through General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET: TSB CONTAINS A NOTIFICATION OF AN OWNER'S LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. IN SOME TRUCKS, THE REAR SEAT ENTERTAINMENT SYSTEM WAS INSTALLED WITHOUT VALIDATION APPROVAL AND WOULD NEED TO HAVE HINGED SCREEN STYLE REAR SYSTEM REPLACED AND REMOVED WITH REVISED INTEGRAL SCREEN. MODEL 2014-15 SILVERADO, SUBURBAN, TAHOE, SIERRA, YUKON. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CADILLAC/ GMC/ CHEVROLET: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. BATTERY IS DEAD DUE TO ONSTAR MODULE AND IF VEHICLE FAILS TO START AFTER 4 DAYS AND OCCURS EVEN IF ONSTAR SYSTEM IS NOT ACTIVE. *PE UPDATED 11/6/15. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a radio display does not always return to the previous call/source screen when a Bluetooth call has ended and/or that the call timer may continue to flash and increment. The call/source screen staying displayed is a normal operating characteristic and cannot be changed. Technician should updated the Human Machine Interface to prevent the call timer from flashing and incrementing after the call has ended.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information for a customer concern of intermittent clicking/rubbing noise when side door glass is moving up or down at cold temperatures.
Source components: BACK OVER PREVENTION · VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information for a customer concern of intermittent clicking/rubbing noise when side door glass is moving up or down at cold temperatures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
14300 - SERVICE UPDATE (RESUME REPAIRS MESSAGE ONLY). ON MARCH 5, 2015, DEALERS WERE SENT A MESSAGE INFORMING THEM TO SUSPEND REPAIRS FOR SERVICE UPDATE 14300 DUE TO A POSSIBLE QUALITY ISSUE ON THE ACTUATOR ASSEMBLY USED TO PERFORM THE REPAIR. OUR INVESTIGATION HAS COMPLETED AND NO QUALITY ISSUES WERE FOUND. EFFECTIVE IMMEDIATELY, REPAIRS CAN NOW BEGIN AGAIN ON INVOLVED VEHICLES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a Service Engine Soon Malfunction Indicator Lamp on and a misfire or a tick noise. Technician may find a Diagnostic Trouble Code P0300 set. If Service Information diagnosis does not isolate the cause of this concern inspect the valve operation. If the valve or valves are not moving the replace the Active Fuel Management lifters and guide on the bank with the concern and the Valve Lifter Oil Assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have battery draw complaint. Technician should not replace the Instrument Panel Cluster for this concern. Technician should test the battery on the vehicle before performing any diagnostics. Low voltage can be caused by a number of reasons discharged battery, battery cable connections, infrequent usage, extended storage, short trip driving, extended key on accessory usage with the engine off, charging issues, and aftermarket electrical accessories.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a radio display that flickers at first start up. Engineering is currently evaluating this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the E92 Engine Control Module part number 12662034 part restriction through General Motors Product Quality Center has ended. Dealer can order the parts through the regular Customer Care and Aftersales parts process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the radio can be turned on after turning the ignition off and opening the driver?s door. The radio can then be turned back on after the vehicle's Retained Accessory Power has been canceled by simply pressing the power button on the radio. This is a normal characteristic of the key off operation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a Service 4WD message on the Driver Information Center when operated below 10 degrees Fahrenheit (-12 Celsius). Technician may find C0398 or C0326 stored in the Transfer Case Control Module. For vehicles with Regular Production Option Code NQH and NQ6 and only setting Diagnostic Trouble Codes C0398 or C0398 and C0326 the replacement of the actuator motor will correct the concern. Dealer will need to contact General Motors Product Quality Center for further assistance. For vehicles with Regular Production Option Code NQH and NQ6 with other transfer case Diagnostic Trouble Codes. If the vehicle had a Diagnostic Trouble Code C0398 in the transfer case control module stored with any other codes such as C0392, C0396, C0306 or other codes related to rotational position sensor or actuator position sensor it is likely that is causing a C0398 to set and replacement of the actuator will likely not repair the vehicle. For vehicles with Regular Production Option Code NP0 and only have a Diagnostic Trouble Code C0398 stored in the transfer case control module, the technician should insure the transfer case control module calibrations are up-to-date in Tis2Web.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the alarm sounding when learning new key fobs after the original key fobs were lost. Technician will open the driver?s door and allow the Content Theft Deterrent alarm to activate, which will pulse the horns and exterior lamps for approximately 30 seconds and the alarm will shut off at this time. As long as the driver?s door remains open the alarm will not turn back on and the new transmitters can be programmed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the Product Quality Center (PQC) assembly replacement process for Service Agents not required to contact PQC prior to assembly replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the Product Quality Center (PQC) assembly replacement process for Service Agents not required to contact PQC prior to assembly replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how the radio display gets the air ambient temperature. On 1500 series trucks and all sport utility vehicle with regular production option code IO3 radio the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio. On 1500 series trucks and all sport utility vehicle with regular production option code IO4, IO5, or IO6 the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface. On 2500/3500 series trucks production option code IO3 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio. On 2500/3500 series trucks production option code IO4, IO5, or IO6 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may OnStar inoperative and Navigation/GPS/Compass issues. Technician may find Diagnostic Trouble Codes B101D sym 3C and or F0. Technician will gather data using a scan tool and contact General Motors Technical Assistance Center for further assistance. After approval technician will replace the OnStar module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may not level the truck when there is load in the rear of their vehicle or a trailer is attached to the vehicle. Technician will need to inspect the air bags on the shocks for kinked or trapped bags. If any shocks are found with air bags kinked or trapped replace that shock. Then the technician should update the Engine Control Module with the latest calibrations.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a Service 4WD message on the Driver Information Center when operated below 10 degrees Fahrenheit (-12 Celsius). Technician may find C0398 or C0326 stored in the Transfer Case Control Module. For vehicles with Regular Production Option Code NQH and NQ6 and only setting Diagnostic Trouble Codes C0398 or C0398 and C0326 the replacement of the actuator motor will correct the concern. Dealer will need to contact General Motors Product Quality Center for further assistance. For vehicles with Regular Production Option Code NQH and NQ6 with other transfer case Diagnostic Trouble Codes. If the vehicle had a Diagnostic Trouble Code C0398 in the transfer case control module stored with any other codes such as C0392, C0396, C0306 or other codes related to rotational position sensor or actuator position sensor it is likely that is causing a C0398 to set and replacement of the actuator will likely not repair the vehicle. For vehicles with Regular Production Option Code NP0 and only have a Diagnostic Trouble Code C0398 stored in the transfer case control module, the technician should insure the transfer case control module calibrations are up-to-date in Tis2Web.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"15183 - SERVICE UPDATE. THIS BULLETIN PROVIDES A SERVICE PROCEDURE TO REPAIR THE DRIVERS SIDE FRONT ROOF DITCH MOLDING ON CERTAIN VEHICLES. THESE VEHICLES MAY EXHIBIT A WATER LEAK ORIGINATING FROM THE DRIVERS SIDE FRONT ROOF DITCH MOLDING. WATER INTRUSION INTO THE PASSENGER COMPARTMENT COULD WET THE HEADLINER, A-PILLAR MOLDING AND CARPET, POTENTIALLY CAUSING STAINING, MOLD AND MILDEW SMELL."
Source components: STRUCTURE:BODY:ROOF AND PILLARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with various Heater-Vent-Air Conditioning concerns. Technician will need to reprogram HVAC Control Module with the updated calibration available in TIS2WEB starting on 1/17/2015.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides retail and wholesale service personnel with the policies and the warranty claims submission procedures that support Labor Operation 0600014 ? Suspected Tampering or Vehicle Modifications.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides retail and wholesale service personnel with the policies and the warranty claims submission procedures that support Labor Operation 0600014 - Suspected Tampering or Vehicle Modifications.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have a front driver's or passenger's seat back may lean or be turned outward. Technician will need to remove the seat bottom trim cover and reinstall it completely and squarely to the cushion to correct the concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have a radio display flickers momentarily when first starting the vehicle. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a content theft alarm sounding for no apparent reason. Technician may use all published Service Information diagnostics and has not found the cause of the unwanted content theft alarm sounding. Technician should use Global Diagnostic System 2 to review the Body Control Module parameters for "Content Theft Deterrent Trigger History". This is a list of triggers that can cause a content theft alarm sounding. Driver door Passenger door, Left rear door, Right rear door, Rear closure, Tonneau Cover, Hood, Ignition Voltage, Intrusion, Inclination, Telematics enhanced service alarm, Battery reconnect detected, Unauthorized Pulse Width Modulated change, Security Indicates Tamper, and Glass Breakage. If the trigger is an Intrusion inspect for items hanging from the rear view mirror, solar powered dancing characters. When the trigger is a Glass breakage inspect the two rear quarter-panel windows and also in the liftgate glass. The quarter panel windows are attached to the body harness with a connector that looks similar to a 9 volt battery connector inspect them to be fully seated in on the glass. When the trigger is Ignition Voltage/Battery reconnect detected during a cold ambient temperature remote vehicle start event technician should call GM General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle with low miles that may have uneven front brake wear. Technician may find an inner pad worn out more than the outside. Technician will need to call General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that navigation system has inaccurate estimated time of arrival. This is a normal operating characteristic of the New Generation Infotainment system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a Service 4WD message on the Driver Information Center when operated below 10 degrees Fahrenheit (-12 Celsius). Technician may find C0398 or C0326 stored in the Transfer Case Control Module. For vehicles with Regular Production Option Code NQH and NQ6 and only setting Diagnostic Trouble Codes C0398 or C0398 and C0326 the replacement of the actuator motor will correct the concern. Dealer will need to contact General Motors Product Quality Center for further assistance.
Source components: POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information for a customer concern of dome lamps flash/flicker on and off when operating brake pedal or turn signal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a Service Engine Soon Malfunction Indicator Lamp on and a misfire or a tick noise. Technician may find a Diagnostic Trouble Code P0300 set. If Service Information diagnosis does not isolate the cause of this concern inspect the valve operation. If the valve or valves are not moving the replace the Active Fuel Management lifters and guide on the bank with the concern and the Valve Lifter Oil Assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides technicians diagnostic tips for unable to align radar during distance sensing cruise control module learn procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for fleet vehicles which details the proper configurations for the ignition key, fob, key tags and key rings.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides technicians diagnostic tips for unable to align radar during distance sensing cruise control module learn procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides technicians with information on the normal condition of white, milky or cloudy appearance of front differential fluid.
Source components: POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for fleet vehicles which details the proper configurations for the ignition key, fob, key tags and key rings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have hard or unable to rotate ignition key concern. When the concern is present the steering wheel will need to be rotated in either direction to alleviate the pressure between the steering column lock pin and lock plate. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a dimly illuminated Service Engine Soon Malfunction Indicator Lamp when the engine is running. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides technicians a recommendation for when they are performing a front end alignment and find an alignment dowel pin missing .
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides technicians a recommendation for when they are performing a front end alignment and find an alignment dowel pin missing .