2012 Chevrolet SILVERADO Manufacturer communications & TSBs.Page 3
Original record summaries, dates and identifiers for this model-year. Records 201–279 of 279, ordered newest first. Dated records on this page: Apr 1, 2011–Dec 12, 2012.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Dec 12, 2012Service Bulletin/Repair Instructions
PIT3271F
NHTSA communication ID: 10112655
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with a "Service Charging System" message displayed on the Driver Information Center and/or a low voltage reading on the volt gauge during the first several minutes after a cold start. Technician may find a Diagnostic Trouble Code B1517 sym 03. If this concern only occurs during the first several minutes of a cold start, no repairs should be made. Dealer should communicate to the customer that this is normal operating characteristic of vehicles equipped with the diesel engine.
Source components: ELECTRICAL SYSTEM:IGNITION · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a ticking noise when driving above 30 miles per hour in third and fourth gear. Technician will need to replace the Reaction Carrier and the Low and Reverse Roller Clutch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation settings for concernc regarding noice drop outs during calls and muffled sound.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the front seats will not cool when using remote vehicle start. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: ELECTRICAL SYSTEM · SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that have windows inoperative while the engine is running but work when the engine is off. Technician should look for aftermarket parts and remove them and retest the windows before any in depth diagnostics are performed.
Source components: VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers may inquire about the availability of the passenger compartment air filter. Dealer should advise the customer starting in 2003 the passenger compartment air filter is no longer available as a factory option.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the customer or up-fitter may have removed the rear bumper, install a different rear bumper, or add a different box/flat bed/cube box/hitch, etc. to the rear of the truck, which affects the rear park assist operation. Technician can disable the rear park assist for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a rattle, buzz, tick, or vibration type noise that appears to be coming from the center of the dash. Technician will adjust the transmission dipstick tube away from the front of cowl to provide additional clearance.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a buzz or rattle type noise during light acceleration around 1200-2000 Revolutions per minute. Technician will need to reposition the fuel line and bracket down away from the floor pan.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a no crank condition after the vehicle has had very low accessory battery voltage or a dead battery condition. Technician may find Diagnostic Trouble Code P0C76 set. Technician should be advised that anytime a battery charger or booster pack is connected to the 12 volt battery, the ignition key should always be in the off position. If a battery charger or booster pack is connected to the 12 volt battery with the ignition key on tech will need to reset the Hybrid Powertrain Control Module Diagnostic Trouble Codes.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Electronic Brake Control Module and Brake Pressure Modulator Valve for the 2-Mode Hybrid Utilities and Trucks will be placed on a parts restriction through the General Motors Technical Assistance Center. Dealer will need to contact for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a lack of brake assist after disconnecting the battery or after the 12 volts battery has run low on voltage. The Antilock Braking System Malfunction Indicator Lamp may also be on. Technician may find Diagnostic Trouble Code C121D sym 00 or C056D sym 00 set in the Electronic Brake Control Module. Technician should be advised to wait for a period of at least 1 minute with the ignition in the "OFF" position prior to disconnecting the negative battery cable. Technician will need to follow these steps to repair the concern. 1. Install the negative battery cable to the battery. 2. Rotate the lever lock clockwise until an audible click is heard in order to connect the negative battery cable to the battery. 3. Position the negative battery cable insulating cover over the negative terminal. 4. Start the vehicle without stepping on the brake pedal. 5. Shut the vehicle "Off" for one minute. 6. Restart vehicle and check brakes for proper operation. 7. Clear codes in the Engine Control Module and the Electronic Brake Control Module.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES, ELECTRIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about Electronic Brake Control Module relearn procedure is required anytime the Electronic Brake Control Module is replaced or has been Service Programming System reprogrammed.
Source components: EQUIPMENT:ELECTRICAL · SERVICE BRAKES, ELECTRIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the Malfunction Indicator Lamp is illuminated and the vehicle has a harsh 1-2 shift. Technician may find Diagnostic Trouble Code P0741 set in the Transmission Control Module. Technician will need to replace the torque converter clutch solenoid and wire harness with part number 24237980.
Source components: ELECTRICAL SYSTEM:WIRING · POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have water or dust from the openings under the bed rails near the stake pockets. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the roof beacon switch. The roof beacon switch will be left disconnected from the assembly plant. When a roof beacon light is added technician will need to plug the harness into the switch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with additional vehicle speed sensor diagnostic information. Technician may encounter multiple issues when diagnosing a Vehicle Speed Sensor. Technician will find it difficult to follow the speed signal path between the components. To test connect the Fluke meter leads between circuits 821 and 822 and set the meter to Alternating current voltage and then press the hertz button. When the Engine Control Module showing correct miles per hour in the data list however it is setting a Diagnostic Trouble Code for the Vehicle Speed Sensor. To test connect the Fluke meter red lead to circuit 6399 and the black lead to ground, then set the meter to Direct current voltage and press the hertz button. The Instrument Panel Cluster speedo will work correctly when the Engine Control Module or Antilock Braking System Diagnostic Trouble Codes are for the Vehicle Speed Sensor. To test connect the Fluke meter red lead to circuit 1827 and the black lead to ground, then set the meter to Direct current voltage and press the hertz button. When the Antilock Braking System Malfunction Indicator Lamp on with Electronic Brake Control Module Diagnostic Trouble Code C0055 and no other customer complaints, to test connect the Fluke meter red lead to circuit 817 and the black lead to ground, then set the meter to Direct current voltage and press the hertz button.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an Antilock Braking System lamp followed by a Service Stability message in the Drivers Information Center. Technician my find Diagnostic Trouble Code C0710 set in the Electronic Brake Control Module. Technician may or may not find Diagnostic Trouble Code C0455. Technician will need to ensure the steering wheel is properly installed to the steering shaft.
Source components: SERVICE BRAKES, AIR:ANTILOCK · SERVICE BRAKES, ELECTRIC · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a front passenger flooring wet, water sloshing noise, and/or mist from the dash vents. Technician will need to rotate the drain hose to clear the heat shield.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
Source components: SERVICE BRAKES · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0101. Technician should follow published Service Information diagnostics for any Diagnostic Trouble Codes that are set. If during diagnosis the tech has found that the Airflow Leak Equivalency Ratio or Induction System Leak Indication is above or below the specification the tech will have to carefully check for leaks in the air intake.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B0081 in the Sensing and Diagnostic Module and Passenger Presence Sensor modules. Technician should inspect the Sensing and Diagnostic Module and Passenger Presence Sensor powers, grounds, and communication circuits at all in line connectors for fully seated, backed out terminals, and proper terminal tension using the correct test probes.
Source components: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE · AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Technician will need to contact the Techline Customer Support Center to determine if a calibration is available for the vehicle. If they are able to provide a calibration for the vehicle then order steering wheel with cruise control buttons, steering wheel sir coil, and steering column wiring harness.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about hairline cracks may be noticed in the pad friction material, when performing a brake inspection. Technician should be advised that the hairline cracks do not affect the operation of the brake system and the pads should not be replaced if only hairline cracks are found.
Source components: SERVICE BRAKES · SERVICE BRAKES, AIR:DISC:PADS · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:PADS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a high pitch buzz, whine, squeal, or hum noise from the radio display. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: DIAGNOSE AND REPAIR HVAC BLOWER FUNCTION. MAY NOT BE ANY AIR FLOW FROM THE HVAC VENTS. ONE POSSIBLE OF THIS CONDITION MAY BE THE CONTACTS IN THE HVAC JUNCTION BLOCK(S) LOCATED AT THE RIGHT SIDE OF THE INSTRUMENTAL PANEL. *JS UPDATED 1/24/13. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a "Service Stability Message" appears on the Drivers Information Center. Technician will find Diagnostic Trouble Code C0561 set in the Electronic Brake Control Module. Technician will need to address any other Diagnostic Trouble Codes that are set in the vehicle first before working on Diagnostic Trouble Code C0561.
Source components: EQUIPMENT:ELECTRICAL · SERVICE BRAKES, ELECTRIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a vibration, moan, or buzz type noise heard from either inside the passenger compartment, or from under the hood. Technician will need to replace the new design hose with the first design hose. Technician will also rotate the inlet heater hose.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the content theft alarm is inoperative. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. Technician should be advised that the vehicle must have Keyless Entry Regular Production Option Code (AU0/AU3) and Regular Production Option Code YE9 or Y91 to be equipped with content theft alarm.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have grease leaking from front hub bearings. Technician should not replace the bearing for grease purge. Technician should be advised to not clean the purged grease from the area immediately on or adjacent to the seals because this grease provides additional protection. Technician should only replace the bearing if the seals show visible damage, bearing endplay is greater than 0.005" or 0.13mm, bearing exhibits rough rotation, or bearing exhibits abnormal noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that has a squawk or grunt type noise when shifting from 2nd to 3rd gear. Technician should replace the 3-4 clutch Friction and Steel Clutch Plates along with the Apply Plate and Selective Backing Plate.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are unable to set a personalized easy exit seat and/or power tilt column position and they will only move a predetermined amount. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks and Utilities may ask if they can lower their tire pressures. Tire pressures being set to the "Tire and Loading Label" will ensure the safe handling and ride characteristics of the truck and should not be lowered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have passenger window express down feature is inoperative. Technician should be advised that models equipped with either Memory Seats Regular Production Option Code (AN3) and/or Power Folding Mirrors Regular Production Option Code (DL3) will have the passenger window express down feature. Dealer should advised the customer if the vehicle does not have one of the Regular Production Option Codes AN3 and or DL3, this is a normal operating characteristic.
Source components: EQUIPMENT:ELECTRICAL · VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a lack of power on initial acceleration from a stop when the ambient temperature is approximately 103 Fahrenheit or greater and may include engine detonation or pre-ignition type events as temperatures approach 120 Fahrenheit. Technician will need to perform published Service Information diagnosis first. If Service Information diagnosis does not isolate the cause of this concern, take a Tech 2 snapshot of the concern happening and note the Spark Parameter in the Ignition Data List. If it drops near/below 0 degrees during the concern, check if there is a cylinder that shows any knock. If there is a knock in any cylinder perform a top engine clean. If the concern is still present, then switching to premium fuel (91 octane or higher) with detergents (Top tier fuel) when ambient temperatures exceed 110 Fahrenheit degrees, this should provide a slight improvement in engine performance when ambient temperatures are high especially as temperatures approach 120 Fahrenheit degrees.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician abut vehicles that have a knock noise or vibration from the engine or transmission. Technician will need to inspect the flex plate. The flex plate and transmission bell housing should be replaced if the flex plate is found cracked.
Source components: POWER TRAIN · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that if the ignition key is turned to the start position, and then released when the engine begins cranking, the engine will continue cranking for a few seconds or until the vehicle starts. Some customers may state that this feature is inoperative. Technician should be advised that if the Low Fuel warning lamp is on and/or the FUEL LEVEL LOW message is displayed in the Driver Information Center, the Computer?Controlled Cranking System will be disabled.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:IGNITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an instrument panel backlighting flashes, flickers or inoperative, unwanted horn activation, radio controls inoperative or unwanted activation, OnStar unwanted activation, and cruise control inoperative. Technician should inspect for a short to ground on the steering wheel near the Supplemental Inflatable Restraint coil connector X2 and make necessary repairs to any shorted circuits and then position the wiring.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC. · VEHICLE SPEED CONTROL:CRUISE CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the Malfunction Indicator Lamp is illuminated and the vehicle has a harsh 1-2 shift. Technician may find Diagnostic Trouble Code P0741 set in the Transmission Control Module. Technician will need to replace the torque converter clutch solenoid and wire harness with part number 24237980.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a groan, growl, or moan coming from the vehicle when operating the vehicle in four wheel drive. Driving on clean, dry pavement in Four-Wheel Drive High or Four-Wheel Drive Low for an extended period of time may cause premature wear on your vehicle's power train. Dealer should advise the customer not drive on clean, dry pavement in Four-Wheel Drive High or Four-Wheel Drive Low for extended periods of time.
Source components: POWER TRAIN · POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a ticking noise when driving above 30 miles per hour in third and fourth gear. Technician will need to replace the Reaction Carrier and the Low and Reverse Roller Clutch.
Source components: EQUIPMENT:MECHANICAL · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that unable to program the key fobs to the vehicle. Technician will need to contact Techline Customer Support Center to obtain calibrations if adding Remote Keyless entry.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the front and/or rear heated seats are inoperative and/or the driver's power seat only moves in short bursts each time the seat switch is operated. Technician will need to reprogram only the affected module (Memory Seat Module, Rear Heated/Vented Seat Module, or Front Seat Heating Control Module) with updated calibrations in Tis-2-Web.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the cruise control being inoperative. Technician may find Diagnostic Trouble Code B3894 set in the Trailer Brake Control Module. Technician should follow published Service Information diagnostics first. Technician should check the "Master Cylinder Pressure" sensor parameter listed in the Trailer Brake Control Module data list. If it is displaying pressure with no brake pedal input, suspect a concern with the Master Cylinder Pressure Sensor, wiring/terminals, or Electronic Brake Control Module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have passenger window express down feature is inoperative. Technician should be advised that models equipped with either Memory Seats Regular Production Option Code (AN3) and/or Power Folding Mirrors Regular Production Option Code (DL3) will have the passenger window express down feature. Dealer should advised the customer if the vehicle does not have one of the Regular Production Option Codes AN3 and or DL3, this is a normal operating characteristic.
Source components: VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a ticking noise when driving above 30 miles per hour in third and fourth gear. Technician will need to replace the Reaction Carrier and the Low and Reverse Roller Clutch.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/GMC: THE 4WD FAILS TO ENGAGE WHEN SERVICE 4WD INDICATOR ILLUMINATES AND TRANSFER CASE CONTROL MODULE (TCCM) REPORTS POSSIBLE C0379 SET. MODELS 2012-2013 AVALANCHE, SILVERADO, SUBURBAN, TAHOE, SIERRA, YUKON, YUKON XL. *PE
Source components: POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC/CHEVROLET/GMC: WILL HAVE INOPERATIVE CRUISE CONTROL; INOPERATIVE OR UNWANTED ACTIVATION OF RADIO CONTROLS; BACKLIGHTING FLASHES, FLICKERS OR INOPERATIVE DUE TO POSSIBLE SHORT TO GROUND ON STEERING WHEEL COIL CONNECTOR X2. MODELS 2007-2013 ESCALADES MODELS, AVALANCHE, SILVERADO, SUBURBAN, TAHOE, SIERRA, YUKON MODELS. *PE
Source components: ELECTRICAL SYSTEM · STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET: THERE MAY BE AN ACCUMULATION OF DIESEL PARTICULATE FILTER SOOT LEVEL FOUND WHEN A DIAGNOSTIC SYSTEM CHECK IS PERFORMED AND MAY BE CAUSED BY ENGINE CONTROL MODULE (ECM) WITH A REDUCED ENGINE POWER MESSAGE. MODEL 2011-2013 EXPRESS, SILVERADO; SAVANA, SIERRA. *PE
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET/CADILLAC: INSTRUMENT PANEL MESSAGES REGARDING STABILITRAK MESSAGE, TRACTION CONTROL MESSAGE, SERVICE BRAKE SYSTEM MESSAGE, IS OFF AND GAUGES, IN VARIOUS MODULES LOW SPEED SETTINGS, ARE INOPERATIVE. MODELS 2007-13 ALL ESCALADES; AVALANCHE, SILVERADO, SUBURBAN, TAHOE; SIERRA, ALL YUKONS AND DENALIS. *PE
Source components: ELECTRONIC STABILITY CONTROL (ESC) · ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC) · TRACTION CONTROL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC/GMC/CHEVROLET: INFORMATION ON CRUISE CONTROL BEING INOPERATIVE DUE TO BPP CIRCUIT SIGNAL AND/OR TCC/CRUISE BRAKE PEDAL PARAMETERS, WHEN BRAKE PEDAL IS RELEASED BUT SHOWS APPLIED. MODELS 2007-2013 ALL ESCALADES, AVALANCHE, SILVERADO, SUBURBAN, TAHOE, SIERRA, ALL YUKONS. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/GMC/CADILLAC: BRAKE PEDAL POSITION (BPP) SENSOR HAS RELATED ISSUES AFTER NORMAL DIAGNOSTICS, REGARDING CONNECTOR X205, TERMINAL CONCERN, CRUISE/BRAKE LIGHT OR SERVICE STABILITY MESSAGE OR REDUCED ENGINE POWER. MODELS 2012-2013 ALL ESCALADES, AVALANCHE, SILVERADO, SUBURBAN, TAHOE, SIERRA AND ALL YUKONS. *PE
Source components: SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CADILLAC/CHEVROLET: HVAC SYSTEM, WHEN TURNED ON, IS VERY NOISY AND THERE IS A LACK OF AIRFLOW, THROUGH VENTS, DUE TO BLOWER MOTOR FAILING TO WORK PROPERLY. MODELS 2012-2013 ESCALADE, ESV, EXT; AVALANCHE, SILVERADO, SUBURBAN, TAHOE; SIERRA, YUKON, YUKON DENALI, YUKON XL, YUKON XL DENALI. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CADILLAC/CHEVROLET: NO AIR IS FLOWING THROUGH HVAC VENTS BECAUSE OF AN INOPERATIVE BLOWER MOTOR. THE SITUATION IS INTERMITTENT. MODELS 2011-12 CADILLAC-ESCALADE, ESCALADE ESV & EXT; GMC-SIERRA, YUKON & XL, YUKON DENALI & XL DENALI; CHEVROLET-TAHOE, SUBURBAN, AVALANCHE & SILVERADO. *PE UPDATED 9/26/12. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: SERVICE STABILITY MESSAGE LOW POWER BRAKE LIGHT AND CRUISE CONTROL OPERATION- DTC C0161 AND/OR C0277. NEW FOR THE 2012 MODELS IS A DUAL BRAKE PEDAL POSITION (BPP) SENSOR (TWO SENSORS IN ONE). THE DUAL BPP REPLACES THE OLD STYLE OPEN/CLOSED BRAKE SWITCH WHICH HAS BEEN USED FOR YEARS. *JS MODELS 2012-13 ALL ESCALADES; AVALANCHE, EXPRESS, SILVERADO, SUBURBAN, TAHOE; SAVANA, SIERRA, ALL YUKONS AND DENALIS. UPDATED 11/28/12. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/GMC: STARTER MOTOR, ON CERTAIN SUVS, MAY WEAR THRU, AFTER CONTACT, WIRING INSULATION, WHICH CAUSES CIRCUIT CONDITION TO SHORT OUT. STARTER MOTOR BECOMES INOPERATIVE. MODELS 2013 CHEVROLET AVALANCHE, SILVERADO AND GMC SIERRA. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC/CHEVROLET/GMC/HUMMER/PONTIAC: THERE IS SLIPPING OR HAVE NO FOURTH, FIFTH OR SIXTH GEAR AND MALFUNCTION INDICATOR LAMP (MIL) WOULD BE ON, WITH DIAGNOSTIC TROUBLE CODE (DTC) P0796 FOUND AS ACTIVE. *PE
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM-EXPRESS/SILVERADO/SAVANA/SIERRA: DUE TO POOR CONNECTIONS AND INTERMITTENT CONDITION OF MAP SENSOR CONNECTOR WIRING HARNESS TERMINAL CRIMPS, TRUCKS HAVE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION AND REDUCED ENGINE POWER DISPLAY MESSAGE. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET: SOME TRUCKS, EQUIPPED WITH AUTOMATIC TRANSMISSION 4L60E, MAY EXPERIENCE SLIPPING, MISSED OR LATE SHIFTS IN 3RD AND 4TH GEARS DUE TO POSSIBLE 3-4 CLUTCH DISTRESS. *PE
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET: MALFUNCTION INDICATOR LAMP (MIL) IS ILLUMINATED AND HAS A HARSH SHIFT 1-2. THE TCC ENABLE SOLENOID AND WIRE HARNESS SHOULD BE REPLACED WHEN REPAIRS ARE PERFORMED ON TRANSMISSION. *PE
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: J-35616-64B TERMINAL TEST PROBE AND REPLACEMENT TERMINAL. ALSO INCLUDED MODELS VERANO, REGAL, LACROSSE, CTS, SRX, VOLT, SONIC, MALIBU, IMPALA, EQUINOX, CRUZE, AVALANCHE, TAHOE SUBURBAN, SILVERADO, SIERRA, YUKON, AND TERRAIN FOR MODEL YEAR 2013. MODEL ESCALADE MODEL YEAR 2012-2013. MODEL PONTIAC G3 MODEL YEAR 2007. MODEL WAVE MODEL YEARS 2005-2010. DENALI MODELS MODEL YEARS 2007-2013. *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: TICK OR RATTLE NOISE FROM FRONT OF DASH, TRANSMISSION FILLER TUBE CRACKED OR BROKEN (INSPECT FILLER TUBE, REPLACE TUBE AS NECESSARY). *JS UPDATED 05/3/2013 *JS
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: AIR BAG WARNING LAMP ILLUMINATED, REPEAT HISTORY DTC B0083 0F- B0088 0F ON VEHICLES OPERATED IN AMARILLO TEXAS AREA. AN UPDATED SOFTWARE CALIBRATION HAS BEEN RELEASED TO ADDRESS THIS CONDITION. ALSO INCLUDED IN MODELS YEARS 2010-2012 MODEL:CADILLAC ESCALADE HYBRID; CHEVROLET SILVERADO HYBRID; CHEVROLET TAHOE HYBRID;GMC SIERRA DENALI; GMC SIERRA HYBRID;GMC YUKON HYBRID; GMC YUKON DENALI HYBRID. *JS
Source components: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: LOSS OF HIGH SPEED GMLAN COMMUNICATIONS, INTERMITTENT NO CRANK, IP GAGE FLUCTUATION, INTERMITTENT DOOR LOOK CYCLING, INTERMITTENT CHIME OPERATION, VARIOUS IP WARNING LAMPS ILLUMINATED, TRANSMISSION MAY NOT SHIFT, COMMUNICATION DTCS U0073, U0100, U0101, U0102 U0121 OR U0140 SET (REPAIR TERMINALS IN TRANSMISSION HARNESS CONNECTOR, REPAIR OPEN OR SHORTED GM HIGH SPEED LAN CIRCUITS, OPEN OR SHORTED DATA LINK RESISTOR, CORROSION OR POOR CONNECTIONS IN VARIOUS CONTROL MODULE CONNECTORS). *JS
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC: CORRECT FRONT AXLE VENT HOSE ROUTING. THE FRONT AXLE VENT HOSE IS MOUNTED IN THE LEFT SIDE OF THE ENGINE COMPARTMENT, AND MAY NOT BE CORRECTLY ROUTED. *PE UPDATED ON 5/1/2012. *KB
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CADILLAC/CHEVROLET/GMC/HUMMER: SOME SUVS AND TRUCKS ARE EXHIBITING A CONDITION WHERE BY GRINDING/RATCHETING TYPE NOISE COMING FROM AUTOMATIC TRANSMISSION WHEN SHIFTING INTO PARK WHILE IN 4WD LOW (4LO) RANGE. *PE
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/GMC: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. ON CERTAIN MODEL VEHICLES, A CONDITION WHERE ROOF RAIL AIRBAGS, MAY BEEN IMPROPERLY ROUTED ON RIGHT SIDE, RESULTING IN DEPLOYMENT. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/GMC: A CLUNKING NOISE COMING FROM THE REAR OF THE VEHICLE. UPON FURTHER INVESTIGATION, THE TECHNICIAN MAY DIAGNOSE THE NOISE COMING FROM THE REAR SUSPENSION LEAF SPRING AREA. *PE UPDATED 6/30/2011. *KB
Source components: SUSPENSION:REAR:SPRINGS:LEAF SPRING ASSEMBLY · SUSPENSION:REAR:SPRINGS:LEAF SPRING ASSEMBLY:LEAF.