2018 Chevrolet SILVERADO 2500 Manufacturer communications & TSBs.Page 11
Original record summaries, dates and identifiers for this model-year. Records 1,001–1,100 of 1,342, ordered newest first. Dated records on this page: Jan 16, 2018–Apr 27, 2018.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 27, 2018Service Bulletin/Repair Instructions
PIT5308C
NHTSA communication ID: 10137521
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have remote start is inoperative, power lift gate Regular Production Option Code (TB5) is inoperative with the ignition off, Crank no start, Start and Stall, and vehicles equipped with the diesel engine, the blower motor may stay on after the engine is turned off. Technician may find Diagnostic Trouble Code P2537 and/or P129Dset. Technician will need to Use a voltmeter and check circuit 5985 at the Engine Control Module and Transmission Control Module. If no or low voltage is found, use the wiring diagram in Service Information and perform normal circuit diagnosis.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · FUEL SYSTEM, DIESEL · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the HMI module to correct a condition of Radio Control (ICS) Display Does Not Remain Off at Times after it Has Been Turned Off in the Radio Settings Menu due to a software concern.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of water leaking into bed area on trucks equipped with High Desert package.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the filed on vehicles that have the condition of Trailer Electrical Not Working as Intended and/or Trailer Message Displayed.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when a phone does not charge properly or charging cycles is on and off rapidly when connected to the single port USB hub of the vehicle. Technician should check the Human Machine Interface part number Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern if the Human Machine Interface part number ends in 8433. Technician should follow published Service Information diagnostic if the Human Machine Interface part number is not 8433.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the 6.6L Diesel engine Regular Production Option Code (L5P) E41Engine Control Module part number 12683624 restriction has ended.
Source components: ELECTRICAL SYSTEM · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to reprogram the memory set module to correct a condition of Personalization Selections Intermittently Missing from Comfort and Convenience Menu due to a calibration concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Service Stabiltak, ABS, Service Trailer Brake Light, and/or Service Traction Control Indicator Illuminated with DTC C0045 or C0050 Set.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, and displays are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when a phone does not charge properly or charging cycles is on and off rapidly when connected to the single port USB hub of the vehicle. Technician should check the Human Machine Interface part number Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern if the Human Machine Interface part number ends in 8433. Technician should follow published Service Information diagnostic if the Human Machine Interface part number is not 8433.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
Source components: STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Technical Bulletin provides information to correct a customer concern of a siren or whine noise from the in-tank fuel pump at temperatures below -6C or 20F, accompanied by start and stall, no start, loss of power and MIL illuminated. Technicians may find DTCs P0087, P018B, P228A, P228B or P2635 set in ECM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to dealer technicians a repair direction for a whine or siren type noise coming from the in tank fuel pump in cold weather areas due to possible diesel fuel waxing or gelling issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product Allegation Resolution (PAR) claim.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program.
NHTSA source summary · Original PDF not reviewed by Recallfolio
17337 - Product Emission Recall. General Motors has decided to conduct a Voluntary Emission Recall involving certain 2016 model year Chevrolet Colorado, GMC Canyon; 2017 model year Chevrolet Express, GMC Savana; 2017-2018 model year Chevrolet Colorado, Cruze, Silverado HD, GMC Canyon, Sierra HD and 2018 model year Chevrolet Equinox, GMC Terrain vehicles, equipped with a diesel engine. The engine control module in these vehicles may not properly diagnose a fault in the exhaust particulate matter sensor. Additionally, a subset of these vehicles, certain 2017 model year Chevrolet Silverado HD and GM Sierra HD vehicles, may in rare instances exhibit a condition in which the engine surges up to 2,800 RPM during vehicle coast or vehicle braking. Program the engine control module and transmission control module when applicable.
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and /or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.
Source components: BACK OVER PREVENTION: WARNINGS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a customer concern ofIPC gauges inoperative or fluctuate, No Start,No Crank,SIR Light / Service Airbag Message, Service Suspension Message,Radio display blank, Steering Wheel Controls (SWC) not illuminated, Turn Signal no audible feedback,HVAC controls inoperative. During diagnostics a technician may find any of the following DTC's: B1011, B1370, B3980, U0020, U0029, U007D, U0073, U0078, U0100, U0101, U0102, U0104, U0140, U0151, U0155, U0164,U0184, U0186, U0198, U0422. Dealer is instructed to check Serial Data Gateway Module X2 connector for terminal concerns and repair as needed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer side connector are clean and securely fastened. If the vehicle’s 7-way connector socket terminals are deformed or have excessive wear, it will be necessary to replace the truck side connector with part number 23404450.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides additional guidance for diagnosing vibrations or disturbances that may occur on full size pickups and how to correct and repair.
Source components: STRUCTURE:FRAME AND MEMBERS · TIRES · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer technicain a concern with the GPCM service parts(12687698 and 12671083) for 2017 – 2018 vehicles with the 6.6 L5P diesel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin helps the technician on how to determine the difference in small, med, to large leaks in induction or exhaust systems when using a soapy solution or smoke.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, and displays are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while crusing at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
18075 - Service Update. Certain vehicles equipped with an auxiliary battery (RPO K4B) may have the ?buddy clip? to the high-pressure power steering hose and two other clips for the auxiliary negative battery cable not attached consistently during assembly process. Inspect the ?buddy clip? and two auxiliary negative battery cable attachments and secure if required.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY · STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on common diesel engine tick noises and how they are considered part of normal operation and no parts should be replaced for these conditions.
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the drivers front door window regulator motor and door wiring harness if water and/or corrosion is found in the connectors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Service Stabiltak, ABS, Service Trailer Brake Light, and/or Service Traction Control Indicator Illuminated with DTC C0045 or C0050 Set.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES, AIR:ANTILOCK · TRACTION CONTROL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides additional guidance for diagnosing vibrations or disturbances that may occur on full size pickups and how to correct and repair.
Source components: STRUCTURE:FRAME AND MEMBERS · TIRES · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar® Module Functionality After OnStar Module Replacement for Another Condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
18026 - Emissions Recall. General Motors has decided to conduct a Voluntary Emission Recall on certain vehicles equipped with a 6.0L gasoline (L96) engine and dual fuel tanks (N2N). There is a potential that the rear fuel tank inlet check valve may have been damaged during vehicle assembly. If this condition exists it may be possible for fuel or fuel vapor to leak at the connection of the fuel filler hose to the rear fuel tank. Dealers are to replace the rear fuel tank.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
Source components: ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
18019 - Customer Satisfaction Program. Certain vehicles may have a condition in which customers are unable to install the winter grille cover used to increase under hood temperatures, and improve HVAC performance in cold temperatures. Incorrect parts may have been placed in the loose ship items. Replace winter grille cover.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct customer concerns of OnStar, XM, GPS or antenna malfunction ? may set DTC B2462, B2470 or B125C - and/or water leak on headliner at sun visor or overhead console areas, possible battery drain concern.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a lean to the left or right. Technician will need to measure fender wheel-opening heights, front and rear, to quantify vehicle lean. Fender wheel-opening heights are related to, but distinct from, trim height. The front wheel-opening height is known as P height, and the rear wheel-opening height is known as R height. Adjust and heights that are out of specification. After all adjustments are done, perform a front-end alignment and check headlight aim.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to dealer technicians that snow and ice build up is possible if the air filter box is not properly sealed. Aftermarket bumpers may also allow water intrusion.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates repair information for therear vision camera or surround vision camera image being: - Yellow - Blurry -Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message
Source components: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that some vehicles may have a dim Driver Information Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure. This is done to protect the Driver Information Center from damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the correct way to remove the front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.
Source components: ELECTRICAL SYSTEM · SUSPENSION:FRONT:SHOCK ABSORBER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to reprogram the memory set module to correct a condition of Personalization Selections Intermittently Missing from Comfort and Convenience Menu due to a calibration concern.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box removed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesThe vehicle may have an ses lamp with any of the following DTC P06DA, P06DB, P06DC, P06B6, P06B7, P250A, P0300, P0340, P0341, P0335, P0336, P0641, P0011, P0010, P2088, P2089, and/or P2230. Possible crank no start or a stall. possible wiring jumper harness chaffed at the bolt at the X154 connector on lower left side of the frount cover.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
NHTSA source summary · Original PDF not reviewed by Recallfolio
17456 - Customer Satisfaction Program. Certain vehicles may have a condition in which the rear wheel hub nut could become loose due to the rear wheel hub nut retainer not being formed properly. If the hub nut loosens, the StabiliTrak message may be displayed in the driver information center (DIC) and the traction control indicator may illuminate, axle fluid may leak from the axle seal area, and rear axle housing damage could occur. Replace the hub nut retainer. Inspect the axle tube threads for damage and repair if necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
NHTSA source summary · Original PDF not reviewed by Recallfolio
17337 02 Phase 3 - Product Emission. General Motors has decided to conduct a Voluntary Emission Recall involving certain vehicles, equipped with a diesel engine. The engine control module in these vehicles may not properly diagnose a fault in the exhaust particulate matter sensor. Additionally, a subset of these vehicles, certain 2017 model year Chevrolet Silverado HD and GM Sierra HD vehicles, may in rare instances exhibit a condition in which the engine surges up to 2,800 RPM during vehicle coast or vehicle brakingProgram the engine control module, and transmission control module when applicable.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist.Starting with2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that has clearly identified markings. The electric power steering provides a gentle steering correction if a lane marking has been crossed and the driver has not actively responded.
Source components: AIR BAGS · ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC) · FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY · LANE DEPARTURE · POWER TRAIN · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have hard or unable to rotate ignition key concern. When the concern is present the steering wheel will need to be rotated in either direction to alleviate the pressure between the steering column lock pin and lock plate. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:IGNITION · SEAT BELTS · SERVICE BRAKES, HYDRAULIC · STEERING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have either the truck or the snowplow's headlights are flickering or inoperative. There may be a diagnostic trouble code B2575 and or a B2699 set in the body control module. Technician will need to contact the snowplow manufacturer for additional information on their headlight changeover system. Technician is to refer to the latest version of the General Motors up-fitter integration bulletin 116 for additional information these circuits. Technician can find this information at http://www.gmupfitter.com/, under the "Technical Bulletin" Tab and then "Show all bulletins."
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information and definitionsto the technician about vehicles that have fishbite, chuggle, misfire,AFM disturbances or torque converter shudder/vibrationconcerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed and no debris is found in the transmission fluid pan the technicians are instructed to flush the transmission fluid three times. If debris is found in the transmission fluid pan the technicians are instructed to also replace the torque converter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the trans control solenoid assembly if found the cause of the vehicle unable to crank the engine over.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
Source components: BACK OVER PREVENTION · FUEL SYSTEM, GASOLINE · POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT.