2018 Chevrolet SILVERADO 1500 Manufacturer communications & TSBs.Page 12
Original record summaries, dates and identifiers for this model-year. Records 1,101–1,200 of 1,232, ordered newest first. Dated records on this page: Oct 1, 2017–Nov 19, 2018.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Nov 19, 2018Service Bulletin/Repair Instructions
PIP5570A
NHTSA communication ID: 10151863
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer a condition where a tick noise may be present inside a vehicle while driving. This may be the result of a deformed or improperly seated steering shaft seal allowing engine compartment sounds into the vehicle. Dealers are instructed to replace or reinstall the boot as needed and are informed the condition is being reviewed by engineering.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of additional information when diagnosing a service driver assist message with a diagnostic trouble code B172E and or a B172F. The haptic seat motor has a pigtail lead coming off of it. In many cases the wiring pigtail near the haptic seat motor has broken and will require replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Update. Certain vehicles may have one or multiple DTCs that are incorrectly illuminating the service engine soon (SES) light. Hardware including fuel injectors and exhaust gas recirculation (EGR) valves may have been used to fix this issue, however, the condition could return after these repairs were made. There is no effect for vehicle performance.
Source components: ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM) · FUEL SYSTEM, GASOLINE · FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a whistle noise in the vehicle from the driver or passenger side. Technician will need to inspect for voids in the body sealer on the left or right side A-pillar. Technician should also inspect for voids in the body sealer at the cowl seam and apply sealer as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of A/C Not Cool Due to No Pressure Build.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Missing/Wrong Wheel Trim Shipped with New Vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer an issue where the vehicle's service engine soon light may illuminate due to trouble codes P0601-P0604, P0606, P062B, P062F, P0630, P16F3, or P262B . The dealer is to inspect the engine control module's electrical connections and for proper powers and grounds. Dealer instructed to replace the Engine Control Module, if no other issues found.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering informational bulletin is requesting information pictures of windshield, steering wheel and/or door trim panel for product issues covered under warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a detent / click with a feel of increased resistance when the accelerator pedal is about ¾ of the way. The new accelerator pedal design has a built-in detent position near the last 1/4 of pedal travel. Dealer should communicate to the customer this is a normal operating characteristic of the vehicle and no repair attempts should be performed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesSES lamp, setting DTC P0333 when shifting the Transmissionfrom park.DTC P0333 cansetdue to voltage from the Transmission park/neutral signal 1circuit bleeding into the knock sensor system circuits.If SI does not isolate the concern inspect the K20 ECM connector X2 looking for debris, connectorand or terminal concerns.
Source components: POWER TRAIN · POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have issues were the customer will need increased effort to depress the brake pedal. Technician may find fluid in the brake booster and/or the booster vacuum line. Technician will need to replace Vacuum Pump, Brake Booster, Master Cylinder, Vacuum Pump Belt and the Vacuum Line between the booster and the pump.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the dehydrator to correct the condition of A/C Inoperative and/or Insufficient Cooling due to the seals going bad within the part.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the dehydrator to correct the condition of A/C Inoperative and/or Insufficient Cooling due to the seals going bad within the part.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the oil pressure gauge jumps from approximately 40 lb. to 60 lb. The 4.3L (LV3), 5.3L (L83), 6.2L (L86) engines are equipped with a two stage oil pump. Dealer should advise the customer this is normal operation for these engines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates. A vehicle may have a concern ofDTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a repair procedure for a squeak/squawk type noise coming from the lower column/drivers foot well area when turning. It explains how to properly lubricate the column shaft boot where the shaft interacts with the boot where it passes through the boot.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a creak, click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates. A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have a front driver's or passenger's seat back may lean or be turned outward. Technician will need to remove the seat bottom trim cover and reinstall it completely and squarely to the cushion to correct the concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and/or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.
Source components: ELECTRICAL SYSTEM · PARKING BRAKE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer a condition where a tick noise may be present inside a vehicle while driving. This may be the result of a deformed or improperly seated steering shaft seal allowing engine compartment sounds into the vehicle. Dealers are instructed to replace or reinstall the boot as needed and are informed the condition is being reviewed by engineering.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System” message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause: Coolant getting into the cylinders, and provides direction for the repair.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the Generator Control Module (GCM). The dealer technician is advised to call the GMTechnical AssistanceCenter for further assistance
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates that some technicians may find no refrigerant or a low refrigerant charge. Engineering is currently investigating this issue.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a power steering control module calibration error that does not allow its DTC's to transition to history and they always stay current, which can mislead a technician diagnosis. Dealers are to reprogram the power steering control module with updated calibration which will allow DTC's to transition to history if the issue that caused the DTC(s) are now longer present.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the oil pressure gauge jumps from approximately 40 lb. to 60 lb. The 4.3L (L83), 5.3L (L86), 6.2L (LV3) engines are equipped with a two stage oil pump. Dealer should advise the customer this is normal operation for these engines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and /or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.
Source components: BACK OVER PREVENTION: WARNINGS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts when installing the accessory Accessory 22" Wheels Regular Production Option Code (SES, SEU, SEY, OR SEZ) or production 22" wheels Regular Production Option Code (RPT or SMI) also during any service requiring wheel removal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the drivers front door window regulator motor and door wiring harness if water and/or corrosion is found in the connectors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesP0016 setting after internal engire repair. The engine Base timing is not being set correctly. The information in this PI will be helpful in setting the timing in the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to Add 1 quart of coolant to the upper chamber of the surge tank in order to bring the level up to the bottom of the fill neck to correct a condition of the coolant surge tank appears low and/or a low coolant message displayed intermittently due to the fill process at the plant cannot purge all of the air from the cooling system and surge tank.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the A15, Starter Generator (MGU). The dealer technician is advised to call the GMTechnical AssistanceCenter for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates that water leaking into the headlamp assembly or headlamp assembly connections can cause an electrical short which will keep modules from shutting down causing a dead battery and a no crank condition, a crank no start,or unable to program the engine control module. Engine control module will set a diagnostic trouble code of P1682, or the engine will continue to run with the ignition off.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the engine may run hot with the snow plow installed. Do not exceed 64 kilometers per hour / 40 miles per hour with a snow plow mounted to the vehicle even if equipped with VYU. The vehicle could overheat and be damaged.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar. Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.
Source components: STRUCTURE:BODY:HOOD · STRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have Trailer connection not recognized or “Check Trailer wiring” or “Service Trailer Brake” message. Technician may find Diagnostic Trouble Codes C1112, C1113, C1114, C111B, U1556, and/or U1505. Technician will need to inspect the battery and Trailer Brake Power Module connector for corroded terminals and replace as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have installed an aftermarket bed cap or topper may question where they can wire in the center high mounted stop light for the cap or topper. Provisions for the center high mounted stop light have been provided at the Rear Body Junction Block (X63A) connector X6 terminal 1 for 2014-2015 model years. For vehicle model years 2016-2017 provisions for the center high mounted stop light have been provided at connector X400 terminal 4, circuit 1054.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a check engine light on. Technician may find Diagnostic Trouble Code P026A. The owner's manual advises not to drive above 45 MPH with a snowplow installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesA vehicle may have a concern of engine noise and/or a misfire. This may be caused by a broken rocker arm.Abroken rocker arms that could result in the valve dropping to the cylinder, causing a catastrophic failure and the engine requires replacement due to cylinder head and block damage. If a broken rocker arm is found check to see if the valve dropped into the cylinder if so the engine will need to be replaced.On occasions the valve will not drop, reinstall any valve keepers and replace all the intake rocker arms.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that vehicles with front seat Regular Production Option Codes A52, AZ3, or B3F may comment about low treble, or excessive bass from the front door speakers. This is a normal design characteristic for this seat configuration. These vehicles lack a subwoofer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the technician when looking up the P/N for the 3.5 mm audio jack for the USB, to make sure and enter the VIN# to ensure the correct part is being ordered.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have water or dust from the openings under the bed rails near the stake pockets. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct customer concerns of OnStar, XM, GPS or antenna malfunction ? may set DTC B2462, B2470 or B125C - and/or water leak on headliner at sun visor or overhead console areas, possible battery drain concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician how to repair vehicles that Instrument Panel Cluster, Radio, and Heater-Vent-Air Conditioning display blanks out, Bluetooth phone or Pandora connection dropped, the radio station or volume changes when operating the snow plow. Please advise the customer that engineering is aware of this concern and working on this issue.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technician will need to perform a scan for Diagnostic Trouble Codes. Technician will need to follow published Service Information diagnostics if there are Diagnostic Trouble Codes present. If the concern is and intermittent this Preliminary Information communication will be updated with a repair. When the personalization selections are not missing from the Comfort and Convenience menu but they are missing from other menus such as the Climate and Air Quality, Collision/Detection Systems, and Lighting menus, refer to bulletin 17-NA-086. Memory seat adjustments may not be available tech will need to perform a Memory Seat Module replacement/programming.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technician will need to perform a scan for Diagnostic Trouble Codes. Technician will need to follow published Service Information diagnostics if there are Diagnostic Trouble Codes present. If the concern is and intermittent this Preliminary Information communication will be updated with a repair. When the personalization selections are not missing from the Comfort and Convenience menu but they are missing from other menus such as the Climate and Air Quality, Collision/Detection Systems, and Lighting menus, refer to bulletin 17-NA-086. Memory seat adjustments may not be available tech will need to perform a Memory Seat Module replacement/programming.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission, now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates a power steering control module calibration error that does not allow its DTC's to transition to history and they always stay current, which can mislead a technician diagnosis. Dealers are to reprogram the power steering control module with updated calibration which will allow DTC's to transition to history if the issue that caused the DTC(s) are now longer present.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to reprogram the power steering control module to correct a condition of Loss of Steering Assist due to a software abnormality.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015–0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that “mating” surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped
NHTSA source summary · Original PDF not reviewed by Recallfolio
Condition Certain 2018 model year Chevrolet Silverado and GMC Sierra vehicles, equipped with the manual shift transfer case (RPO NQG), may have a condition in which the transfer case shift linkage rod bolt torque is less than specified. Over time this bolt could loosen enough to allow the transfer case shift indicator to be inaccurate; or the bolt could fall off causing the transfer case to remain in its previous position and the shifter to be non-functional. Correction Tighten the transfer case shift linkage rod bolt to the specified torque
Source components: EQUIPMENT · POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Condition Certain 2018 model year Chevrolet Silverado HD and GMC Sierra HD vehicles, equipped with 6.6L diesel engine (RPO L5P) and Allison transmission (RPO MW7), may have a condition in which the automatic transmission has rough upshifts. Correction Reprogram the transmission control module (TCM).
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This engineering information is requesting information from the field on vehicles that have the condition of Speaker Rattle, Speaker Crackle, Poor Sound Quality, Speaker Pop, or Speaker Distortion.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Changing to Camper Outside Rearview Mirrors Some customers may request to have camper style mirrors installed on their vehicle. The new electrical architecture for the Silverado and Sierra has made swapping mirrors a more involved procedure than with previous models. The recommendation has been divided into three upgrades, depending on which mirrors the truck was built with (RPO DE2, DL8 or DL3). Please follow the correct RPO group below, because not all camper mirrors can be installed on all trucks. After selecting the correct RPO mirror the truck was built with, this PI will aid in determining which camper mirrors can be installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Access to the battery specification label, which contains the OEM part number and CCA rating and type, may be difficult without component removal. Refer to the table below for the original equipment ratings and part numbers used to set up a proper battery test. There has been some confusion as to the correct ACDelco battery warranty replacement. Refer to the table below for the correct battery warranty replacement. The correct ACDelco battery warranty replacement in the catalog is designated by the "Original Equipment Replacement" note in the description field.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component